Chapter2-PhysicalLayer.ppt

The Physical Layer
Chapter 2
Computer Networks, Fifth Edition by Andrew Tanenbaum and David Wetherall, © Pearson Education-Prentice Hall, 2011

Outline
• Physical Layer
• Digital-to-Digital Conversion
• Analog-to-Digital Conversion
• Transmission Modes

Physical Layer
 Physical layer in the OSI model plays the role of interacting
with actual hardware and signaling mechanism.
 This layer defines the hardware equipment, cabling, wiring,
frequencies, pulses used to represent binary signals etc.
 Physical layer provides its services to Data-link layer. Data-
link layer hands over frames to physical layer. It also
converts them to electrical pulses, which represent binary
data. The binary data is then sent over the wired or wireless
media.

Physical Layer Functions
 Definition of Hardware Specifications: The details of operation of cables,
connectors, wireless radio transceivers, network interface cards and other
hardware devices are generally a function of the physical.
Encoding and Signaling: The physical layer is responsible for various encoding
and signaling functions that transform the data from bits that reside within a
computer or other device into signals that can be sent over the network.
 Data Transmission and Reception: After encoding the data appropriately, the
physical layer actually transmits the data, and of course, receives it. Note that this
applies equally to wired and wireless networks, even if there is no tangible cable
in a wireless network!
 Topology and Physical Network Design: The physical layer is also considered
the domain of many hardware-related network design issues, such as LAN and
WAN topology.

Signals
When data is sent over physical medium, it needs to be first
converted into electromagnetic signals. Data itself can be
analog such as human voice, or digital such as file on the disk.
Both analog and digital data can be represented in digital or
analog signals.
 Digital Signals
 Digital signals are discrete in nature and represent sequence of
voltage pulses. Digital signals are used within the circuitry of a
computer system.
 Analog Signals
 Analog signals are in continuous wave form in nature and
represented by continuous electromagnetic waves.

Digital-to-Digital Conversion
It explains how to convert digital data into digital signals. It can
be done in two ways, line coding and block coding. For all
communications, line coding is necessary whereas block coding
is optional.
 Line Coding
 The process for converting digital data into digital signal is said to be
Line Coding. Digital data is found in binary format. It is represented
(stored) internally as series of 1s and 0s.

Line Coding Cont..
• Digital signal is denoted by discreet signal, which
represents digital data. There are three types of line
coding schemes available:

Uni-polar Encoding
 Unipolar encoding schemes use single voltage level to represent data.
In this case, to represent binary 1, high voltage is transmitted and to
represent 0, no voltage is transmitted.
 It is also called Unipolar-Non-return-to-zero, because there is no rest
condition i.e. it either represents 1 or 0.

Polar Encoding
 Polar encoding scheme uses multiple voltage levels to represent binary
values.
 Polar Non-Return to Zero (Polar NRZ)
 It uses two different voltage levels to represent binary values. Generally, positive voltage
represents 1 and negative value represents 0. It is also NRZ because there is no rest
condition.
 NRZ scheme has two variants: NRZ-L and NRZ-I.
 NRZ-L changes voltage level at when a different bit is encountered whereas
NRZ-I changes voltage when a 1 is encountered.

Return to Zero (RZ)
 Problem with NRZ is that the receiver cannot conclude when a bit ended
and when the next bit is started, in case when sender and receiver’s clock
are not synchronized.
 RZ uses three voltage levels, positive voltage to represent 1, negative
voltage to represent 0 and zero voltage for none. Signals change during
bits not between bits.

Bipolar Encoding
• Bipolar encoding uses three voltage levels, positive, negative
and zero. Zero voltage represents binary 0 and bit 1 is
represented by altering positive and negative voltages.

Block Coding
 To ensure accuracy of the received data frame redundant bits are used.
For example, in even-parity, one parity bit is added to make the count of
1s in the frame even. This way the original number of bits is increased. It
is called Block Coding.
 Block coding is represented by slash notation, mB/nB. Means, m-bit
block is substituted with n-bit block where n > m.
 Block coding involves three steps:
 Division
 Substitution
 Combination

Analog-to-Digital Conversion
 Microphones create analog voice and camera creates analog videos,
which are treated is analog data. To transmit this analog data over digital
signals, we need analog to digital conversion.
 Analog data is a continuous stream of data in the wave form whereas
digital data is discrete. To convert analog wave into digital data, we use
Pulse Code Modulation (PCM).
 PCM is one of the most commonly used method to convert analog data
into digital form. It involves three steps:
 Sampling
 Quantization
 Encoding.

Sampling
• The analog signal is sampled every T interval. Most important factor in
sampling is the rate at which analog signal is sampled. According to
Nyquist Theorem, the sampling rate must be at least two times of the
highest frequency of the signal.

Quantization
 Sampling yields discrete form of continuous analog signal. Every discrete
pattern shows the amplitude of the analog signal at that instance.
 The quantization is done between the maximum amplitude value and the
minimum amplitude value.
 Quantization is approximation of the instantaneous analog value.

Encoding
• In encoding, each approximated value is then converted into
the nearest level of binary format.

Transmission Modes
 The transmission mode decides how data is transmitted between two
or more computers or devices. The binary data in the form of 1s and
0s can be sent in two different modes:
 Parallel
 Serial

Parallel Transmission
 The binary bits are organized into groups of fixed length.
 Both sender and receiver are connected in parallel with the equal number of data
lines.
 Both computers distinguish between high order and low order data lines. The
sender sends all the bits at once on all lines. Because the data lines are equal to
the number of bits in a group or data frame, a complete group of bits (data frame)
is sent in one go.
 Parallel transmission is high speed and disadvantage is the cost of wires, as it is
equal to the number of bits sent in parallel.

Serial Transmission
• In serial transmission, bits are sent one after another in a queue manner.
Serial transmission requires only one communication channel.
• Serial transmission can be either asynchronous or synchronous.

Serial Transmission
 Asynchronous Serial Transmission
 It is named so because there’is no importance of timing. Data-bits have specific pattern
and they help receiver recognize the start and end data bits. For example, a 0 is
prefixed on every data byte and one or more 1s are added at the end.
 Two continuous data-frames (bytes) may have a gap between them.
 Synchronous Serial Transmission
 Timing in synchronous transmission has importance as there is no mechanism followed
to recognize start and end data bits. There is no pattern or prefix/suffix method. Data
bits are sent in burst mode without maintaining gap between bytes (8-bits). Single burst
of data bits may contain a number of bytes. Therefore, timing becomes very important.
 It is up to the receiver to recognize and separate bits into bytes.The advantage of
synchronous transmission is high speed, and it has no overhead of extra header and
footer bits as in asynchronous transmission.

Digital-to-Analog Conversion
 When data from one computer is sent to another via some analog carrier, it
is first converted into analog signals. Analog signals are modified to reflect
digital data.
 An analog signal is characterized by its amplitude, frequency, and phase.
There are three kinds of digital-to-analog conversions:
 Amplitude Shift Keying
 In this conversion technique, the amplitude of analog carrier signal is modified to reflect binary data.
 When binary data represents digit 1, the amplitude is held; otherwise it is set to 0. Both frequency and phase
remain same as in the original carrier signal.

Cont…
 Frequency Shift Keying
 In this conversion technique, the frequency of the analog carrier signal is modified to
reflect binary data.
 This technique uses two frequencies, f1 and f2. One of them, for example f1, is chosen
to represent binary digit 1 and the other one is used to represent binary digit 0. Both
amplitude and phase of the carrier wave are kept intact.

Cont…
 Phase Shift Keying
 In this conversion scheme, the phase of the original carrier signal is altered to reflect
the binary data.
 When a new binary symbol is encountered, the phase of the signal is altered.
Amplitude and frequency of the original carrier signal is kept intact.

Cont..
 Quadrature Phase Shift Keying
 QPSK alters the phase to reflect two binary digits at once. This is
done in two different phases. The main stream of binary data is
divided equally into two sub-streams. The serial data is converted in
to parallel in both sub-streams and then each stream is converted to
digital signal using NRZ technique. Later, both the digital signals are
merged together.

Analog-to-Analog Conversion
• Analog signals are modified to represent analog data. This conversion is
also known as Analog Modulation. Analog modulation is required when
bandpass is used. Analog to analog conversion can be done in three
ways:

Cont…
 Amplitude Modulation
 In this modulation, the amplitude of the carrier signal is modified to reflect the analog
data.
 Amplitude modulation is implemented by means of a multiplier. The amplitude of
modulating signal (analog data) is multiplied by the amplitude of carrier frequency,
which then reflects analog data.
 The frequency and phase of carrier signal remain unchanged.
 Frequency Modulation
 In this modulation technique, the frequency of the carrier signal is modified to reflect
the change in the voltage levels of the modulating signal (analog data).
 The amplitude and phase of the carrier signal are not altered.
 Phase Modulation
 In the modulation technique, the phase of carrier signal is modulated in order to reflect
the change in voltage (amplitude) of analog data signal.
 Phase modulation is practically similar to Frequency Modulation, but in Phase
modulation frequency of the carrier signal is not increased. Frequency of carrier is signal
is changed (made dense and sparse) to reflect voltage change in the amplitude of
modulating signal.

Transmission Impairments
 Transmission Impairment
When signals travel through the medium they tend to deteriorate. This may
have many reasons as given:
 Attenuation
 For the receiver to interpret the data accurately, the signal must be
sufficiently strong. When the signal passes through the medium, it tends to
get weaker. As it covers distance, it loses strength.
 Dispersion
 As signal travels through the media, it tends to spread and overlaps. The
amount of dispersion depends upon the frequency used.
 Delay distortion
 Signals are sent over media with pre-defined speed and frequency. If the
signal speed and frequency do not match, there are possibilities that signal
reaches destination in arbitrary fashion. In digital media, this is very critical
that some bits reach earlier than the previously sent ones.

Noise
Random disturbance or fluctuation in analog or digital signal is said to be
Noise in signal, which may distort the actual information being carried. Noise
can be characterized in one of the following class:
 Thermal Noise
 Heat agitates the electronic conductors of a medium which may introduce
noise in the media. Up to a certain level, thermal noise is unavoidable.
 Intermodulation
 Intermodulation noise occurs if two different frequencies are sharing a
medium and one of them has excessive strength or the component itself is not
functioning properly, then the resultant frequency may not be delivered as
expected.
 Crosstalk
 This sort of noise happens when a foreign signal enters into the media. This is
because signal in one medium affects the signal of second medium.
 Impulse
 This noise is introduced because of irregular disturbances such as lightening,
electricity, short-circuit, or faulty components.

Transmission Media
The media over which the information between two computer
systems is sent, called transmission media. Transmission media
comes in two forms.
 Guided Media
 All communication wires/cables are guided media, such as UTP, coaxial
cables, and fiber Optics. In this media, the sender and receiver are directly
connected and the information is send (guided) through it.
 Unguided Media
 Wireless or open air space is said to be unguided media, because there is
no connectivity between the sender and receiver. Information is spread
over the air, and anyone including the actual recipient may collect the
information.

Guided Transmission Media
• Magnetic media
• Twisted pairs
• Coaxial cable
• Power lines
• Fiber optics

Magnetic Media
 One of the most convenient way to transfer data from one computer to
another, even before the birth of networking, was to save it on some
storage media and transfer physical from one station to another.
 For example, a bank has to handle and transfer huge data of its customer.
If the bank needs to store its huge backup data then its, transfer through
internet is not feasible. The WAN links may not support such high speed.
Even if they do; the cost too high to afford.
 In these cases, data backup is stored onto magnetic tapes or magnetic
disks, and then shifted physically at remote places.
 Write data onto magnetic media
 Disks
 Tapes

Twisted Pair Cable
 A twisted pair cable is made of two plastic insulated copper wires twisted
together to form a single media. Out of these two wires, only one carries
actual signal and another is used for ground reference. The twists between
wires are helpful in reducing noise (electro-magnetic interference) and
crosstalk.
 There are two types of twisted pair cables:
 Shielded Twisted Pair (STP) Cable: STP cables comes with twisted wire
pair covered in metal foil. This makes it more indifferent to noise and
crosstalk.
 Unshielded Twisted Pair (UTP) Cable: UTP has seven categories, each
suitable for specific use. In computer networks, Cat-5, Cat-5e, and Cat-6
cables are mostly used. UTP cables are connected by RJ45 connectors.

Twisted Pairs

Basis for comparison UTP STP
Basic
UTP (Unshielded twisted
pair) is a cable with wires
that are twisted together.
STP (Shielded twisted pair)
is a twisted pair cable
enclosed in foil or mesh
shield.
Noise and crosstalk
generation
High comparatively.
Less susceptible to noise
and crosstalk.
Grounding cable Not required Necessarily required
Ease of handling
Easily installed as cables
are smaller, lighter, and
flexible.
Installation of cables is
difficult comparatively.
Cost Cheaper and does not
require much maintenance.
Moderately expensive.
Data Rates Slow comparatively. Provides high data rates

Coaxial Cable
 Coaxial cable has two wires of copper. The core wire lies in the
center and it is made of solid conductor.The core is enclosed in an
insulating sheath.The second wire is wrapped around over the sheath
and that too in turn encased by insulator sheath.This all is covered
by plastic cover.
 Because of its structure,the coax cable is capable of carrying high
frequency signals than that of twisted pair cable.The wrapped
structure provides it a good shield against noise and cross talk.
Coaxial cables provide high bandwidth rates of up to 450 mbps.
 There are three categories of coax cables namely, RG-59 (Cable
TV), RG-58 (Thin Ethernet), and RG-11 (Thick Ethernet). RG
stands for Radio Government.
 Cables are connected using BNC connector and BNC-T. BNC
terminator is used to terminate the wire at the far ends.

Coaxial Cable
A coaxial cable

Power Lines
 Power Line communication (PLC) is Layer-1 (Physical Layer) technology
which uses power cables to transmit data signals.In PLC, modulated data
is sent over the cables. The receiver on the other end de-modulates and
interprets the data.
 Because power lines are widely deployed, PLC can make all powered
devices controlled and monitored. PLC works in half-duplex.
 There are two types of PLC:
 Narrow band PLC
 Broad band PLC
 Narrow band PLC provides lower data rates up to 100s of kbps, as they
work at lower frequencies (3-5000 kHz).They can be spread over several
kilometers.
 Broadband PLC provides higher data rates up to 100s of Mbps and works
at higher frequencies (1.8 – 250 MHz).They cannot be as much extended
as Narrowband PLC.

Power Lines
A network that uses household electrical wiring.

Fiber Optics
 Fiber Optic works on the properties of light. When light ray hits at critical
angle it tends to refracts at 90 degree. This property has been used in fiber
optic. The core of fiber optic cable is made of high quality glass or plastic.
From one end of it light is emitted, it travels through it and at the other end
light detector detects light stream and converts it to electric data.
 Fiber Optic provides the highest mode of speed. It comes in two modes, one
is single mode fiber and second is multimode fiber. Single mode fiber can
carry a single ray of light whereas multimode is capable of carrying multiple
beams of light.
 Fiber Optic also comes in unidirectional and bidirectional capabilities. To
connect and access fiber optic special type of connectors are used. These
can be Subscriber Channel (SC), Straight Tip (ST), or MT-RJ.

Fiber Optics (1)
Three examples of a light ray from inside a
silica fiber impinging on the air/silica boundary
at different angles.

Fiber Optics (2)
Light trapped by total internal reflection.

Transmission of Light Through Fiber
Attenuation of light through fiber
in the infrared region

Fiber Cables (1)
Views of a fiber cable

Fiber Cables (2)
A comparison of semiconductor diodes
and LEDs as light sources

Channel Capacity
The speed of transmission of information is said to be the
channel capacity. We count it as data rate in digital world. It
depends on numerous factors such as:
 Bandwidth: The physical limitation of underlying media.
 Error-rate: Incorrect reception of information because of
noise.
 Encoding: The number of levels used for signaling.

The Maximum Data Rate of a Channel
• Nyquist’s theorem
• Shannon’s formula for capacity of a noisy channel

Multiplexing
 Multiplexing is a technique to mix and send multiple data streams
over a single medium.
 This technique requires two system hardware
 The multiplexer (MUX) is used for multiplexing the streams and
sending them on a medium, and de-multiplexer (DMUX) which
takes information from the medium and distributes to different
destinations.

Switching
 Switching is a mechanism by which data/information sent
from source towards destination which are not directly
connected.
 Networks have interconnecting devices, which receives data
from directly connected sources, stores data, analyze it and
then forwards to the next interconnecting device closest to the
destination.
 Switching can be categorized as:
 Circuit Switching
 Packet Switching
 Message Switching

Circuit Switching/Packet Switching (1)
(a) Circuit switching. (b) Packet switching.

Wireless Transmission
• The Electromagnetic Spectrum
• Radio Transmission
• Microwave Transmission
• Infrared Transmission
• Light Transmission

The Electromagnetic Spectrum (1)
The electromagnetic spectrum and
its uses for communication

The Electromagnetic Spectrum (2)
Spread spectrum and ultra-wideband
(UWB) communication

Radio Transmission (1)
In the VLF, LF, and MF bands, radio waves follow the curvature
of the earth

Radio Transmission (2)
In the HF band, they bounce off the ionosphere.

The Politics of the Electromagnetic
Spectrum
ISM and U-NII bands used in the
United States by wireless devices

Light Transmission
Convection currents can interfere with laser communication
systems. A bidirectional system with two lasers is pictured here.

Communication Satellites
• Geostationary Satellites
• Medium-Earth Orbit Satellites
• Low-Earth Orbit Satellites
• Satellites Versus Fiber

Communication Satellites
Communication satellites, some properties, including: altitude
above earth, round-trip delay time, number of satellites for
global coverage.

Geostationary Satellites (1)
The principal satellite bands

Geostationary Satellites (2)
VSATs using a hub.

Low-Earth Orbit Satellites (1)
The Iridium satellites form six necklaces
around the earth.

Relaying in space.

Relaying on the ground

Chapter2-PhysicalLayer.ppt

More Related Content

What's hot (20)

Similar to Chapter2-PhysicalLayer.ppt (20)

Recently uploaded (20)

Chapter2-PhysicalLayer.ppt