chapter3.pptx electrical engineering for university

1
Basic and Derived Logic Gates

2
Basic Logic Gates
Boolean algebra
Boolean Constants and Variables
 Boolean algebra differs in a major way from ordinary
algebra in that Boolean constants and variables are allowed
to have only two possible values, 0 or 1.
 Boolean Variable is a quantity that may, at different times,
be equal to either 0 or 1 .
 The Boolean Variables are often used to represent the
voltage level represent on a wire or input/output terminal of
a circuit.
 For example: in a certain digital system the Boolean Value
of 0 might be assigned to any voltage in the range from 0 to
0.8V while the Boolean value of 1 might be assigned to any
voltage in the range of 2 to 5V.
 Voltage b/w 0.8 and 2V are undefined (neither 0 nor 1) and
under normal circumstances should not occur.

3
 Thus, Boolean 0 and 1 do not represent actual
numbers but instead represents the state of voltage
variable, or what is called its logic level.
 A voltage in a digital circuit is said to be at logic
level 0 or the logic level 1, depending on its actual
numerical value.
 In table below, some of the more common terms in
the digital logic field are shown.
LOGIC 0 LOGIC 1
False
Off
Low
No
Open switch
True
On
High
Yes
Closed switch

4
 In all our works to follow we shall use letter
symbols to represent logic variables.
 Because only two values are possible, Boolean
algebra is relatively easy to work with as compared
with ordinary algebra.
 In Boolean algebra there are no decimals, fractions,
negative numbers, square root, logarithms,
imaginary number, and so on.
 In Boolean algebra there are only three basic
operation; OR, AND and NOT.
 These basic operations are called logic operations
 Digital circuits called logic gates can be
constructed from diode, transistors, and resistors
connected in such a way that the circuit output is
the result of a basic logic operation (OR, AND,
NOT) performed on the inputs.

5
Truth Tables
 Many logic circuits have more than one input
and only one output.
 A truth table shows how the logic circuit's
output responds to the various combinations
of logic levels at the inputs.
 The format for two-, three-, and four-input truth
tables is shown in Table below
 The number of input combinations will equal
2N for an N-input truth table.
Inputs Output
A B Y
0 0 ?
0 1 ?
1 0 ?
1 1 ?
Inputs Output
A B C Y
0 0 0 ?
0 0 1 ?
0 1 0 ?
0 1 1 ?
1 0 0 ?
1 0 1 ?
1 1 0 ?
1 1 1 ?
Inputs Output
A B C D Y
0 0 0 0 ?
0 0 0 1 ?
0 0 1 0 ?
0 0 1 1 ?
0 1 0 0 ?
0 1 0 1 ?
0 1 1 0 ?
0 1 1 1 ?
1 0 0 0 ?
1 0 0 1 ?
1 0 1 0 ?
1 0 1 1 ?
1 1 0 0 ?
1 1 0 1 ?
1 1 1 0 ?
1 1 1 1 ?
Truth table for
two-input
Truth table for
three-input
Truth table for
four-input

6
OR OPERATION
 Let A and B represents two independent logic variables.
 When A and B are combined using the OR operation the result Y
can be expressed as
Y = A+B
 In this expression the + sign does not stand for ordinary addition;
it stands for the OR operation, whose rules are given in the truth
table shown below
A B Y= A+B
0 0 0
0 1 1
1 0 1
1 1 1

7
It should be apparent from the truth table that
except for the case where A=B=1, the OR operation
is the same as ordinary operation.
However, for A=B=1 the OR sum is 1 (not 2 as in
ordinary addition).
This is easy to remember if we recall that only 0 and
1 are possible values in Boolean algebra, so that
the largest value we can get is 1.
This same result is true if we have Y= A+B+C, for
the case where A=B=C=1 that is
Y= 1+1+1 = 1
We can therefore say that the OR operation result
will be 1 if any one or more variables is a 1
The expression Y= A+B is read as
‘’Y equals A OR B’’

8
Discrete OR Gate
A
B
Y
T2
T1 T3
+5 V
R
Two-input
diode OR Gate
Two-input
Transistor OR gate
Y
A
B
D1
D2
R
A B Y
0 0 0
0 1 1
1 0 1
1 1 1
Truth Table

9
Example: Determine the OR gate output in Figure below. The OR gate
inputs A and B are varying according to the timing diagrams shown. For
example, A starts out LOW at time to, goes HIGH at t1, back LOW at t3, and
so on.
0
1
0
1
0
1
A
B
t7
t0 t1 t2 t3 t4 t5 t6
Output
Y

10
AND OPERATION
 If two logic variables A and B are
combined using the AND operation, the
result, Y, can be expressed as
Y= A·B
 In this expression the ∙ sign stands for
the Boolean AND operation whose
rules are given in the truth table shown
in figure below.
 It should be apparent from the table
that the AND operation is exactly the
same as ordinary multiplication.
 Whenever A or B is 0, their product is
zero, when both A and B are 1, their
product is 1. We can therefore say that
in the AND operation the result will be 1
only if all the inputs are 1: for all other
cases the result is 0.
 The expression Y= A.B is read ‘’Y
equals A AND B’’
 The multiplication sign is generally
omitted as in ordinary algebra, so that
the expression becomes Y=AB
A B Y= A.B
0 0 0
0 1 0
1 0 0
1 1 1

11
AND Gate
 The logic symbol for a two- input AND
gate is shown in fig. Below
 The AND gate output is equal to the AND
product of the logic inputs i.e. Y= AB.
 In other words, the AND gate is a circuit
that operates in such a way that its output
is HIGH only when all its inputs are
HIGH.
 For all other cases the AND gate output
is LOW.
 This same operation is Characteristic of
AND gates with more than two inputs.
 A three-input AND gate and its
accompanying truth table are shown in
fig. Below.
Summary of the AND operation
 The AND operation is performed
exactly like ordinary multiplication 1s
and 0s
 The output equal to 1 occurs only for
the single case where all inputs are 1
 The output is 0 for any case where one
or more inputs are 0.
Logic symbol of AND gate
A
B
AB
=
Y
A
B ABC
=
Y
C
Logic symbol of
three-input AND gate
A B C Y=ABC
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
0
0
0
0
0
0
1

12
+5 V
Y
A
B
A
B
Y
T2
T1
T3
+5 V
Two-input
diode AND Gate Two-input
Transistor AND gate
Discrete AND Gate
A B X
0 0 0
0 1 0
1 0 0
1 1 1
Truth Table

13
Example: Determine the output from the AND gate in
Figure below for the given input waveforms.
Solution
0
1
0
1
0
1
A
B
t7
t0 t1 t2 t3 t4 t5 t6
Output

14
NOT OPERATION
 The NOT operation is unlike the OR and AND
operation in that it can be performed on a
single input variable.
 Example: If the variable A is subjected to the
NOT operation, the result Y can be expressed
as
Y= Ā
 Where the over bar represents the not
operation.
 This expression is read as
 ‘’Y equals NOT A’’ or
 ‘’Y equals the inverse of A ‘’ or
 ‘’Y equals the complement of A’’.
 All indicate that the logic value of Y= Ā is
opposite to the logic value of A.
 The truth table below clarifies this for the two
cases
NOT Circuit (INVERTER)
 Fig below, shows the symbol for a not circuit,
which is more commonly called an
INVERTER.
 This circuit always has only a single input
and its output logic level is always opposite
to the logic level of this input.
A Y= Ā
0
1
1
0
A A
=
Y
Presence of small circle
always denotes inversion

15
Discrete NOT Gate
T
A
R
Y
+5 V
Transistor as Inverter
A Y
0 1
1 0
Truth Table

16
Summary of Boolean operation
The rules for the OR, AND, and NOT
operation may be summarized as follows:
OR AND NOT
0+0 = 0 0·0 = 0
0+1 = 1 0·1 = 0
1+0 = 1 1·0 = 0
1+1 = 1 1·1 = 1
1
0 
0
1

17
Derived Logic Gates
NOR GATES & NAND GATES
 Two other types of logic gates, NOR
gates and NAND gates, are used
extensively in digital circuitry.
 These gates are derived from
combination of the basic AND, OR and
NOT gates, which make it relatively easy
to describe them using the Boolean
algebra operations learned previously.

18
NOR Gate
 The NOR gate is actually a NOT OR gate.
In other words, the output of an OR gate
is inverted to form a NOR gate.
 The logic symbol for the NOR gate is
diagramed in fig (a).
 Note that the NOR symbol is an OR
symbol with a small invert bubble (small
circle) on the right side
 The NOR function is being performed by
an OR gate and an INVERTER in fig (b)
 The Boolean expression for the final
NOR function is .
 The truth table in fig below shows that
the NOR gate output is the exact inverse
of the OR gate output for all possible
input conditions.
 The OR gate output goes HIGH when any
input is HIGH, while the NOR gate output
goes LOW when any input is HIGH.
A
B
B
+
A
=
Y
Denotes
inversion
Fig (a)
Fig (b)
A
B
B
+
A
=
Y
INPUTS OUTPUTS
A B OR NOR
0
1
0
1
0
0
1
1
0
1
1
1
1
0
0
0
Truth table for
OR and NOR gates
Fig (c)
B
+
A
=
Y

19
Discrete NOR Gate
Discrete two-input NOR gate
A
Y
T2
+5 V
T1
B
A B Y
0 0 1
0 1 0
1 0 0
1 1 0
Truth Table

20
NAND Gate
 The NAND gate is a NOT AND, or an
inverted AND function.
 The Standard logic symbol for the NAND
gate is diagramed in fig (a).
 The little invert bubble (small circle) on
the right end of the symbol means to
invert the AND.
 Fig (b) shows a separate AND gate and
inverter being used to produce the NAND
logic function.
 The truth table in fig. (c) shows that the
NAND gate output is the exact inverse of
the AND gate for all possible input
conditions
 The AND output goes HIGH only when all
inputs are HIGH, while the NAND output
goes LOW only when all input are HIGH.
A
B
B
A
=
Y
Fig (c)
A
B
AB
=
Y
INPUTS OUTPUTS
A B AND NAND
0
1
0
1
0
0
1
1
0
0
0
1
1
1
1
0
Fig (b)
Fig (a)

21
Discrete NAND Gate
Discrete two-input NAND gate
A
B
Y
T
+5 V
R
A B Y
0 0 1
0 1 1
1 0 1
1 1 0
Truth Table

22
Universality of NAND Gates and NOR gates
 All Boolean expressions consist of various
combinations of the basic operations of OR, AND,
and INVERTER.
 Therefore, any expression can be implemented using
combinations of OR gates, AND gates and
INVERTERS.
 It is possible, however to implement any logic
expression using only NAND gates and no other type
of gate.
 This is because NAND gates, in the proper
combination, can be used to perform each of the
Boolean operations OR, AND, and INVERTER.
 This is demonstrated in fig below.

23
Universality of NAND Gates
A A
=
A.A
=
Y
 INVERTER
A
B
B
A 
AB
=
Y
AND

A
B
A
B
B
A
=
Y
OR


24
Universality of NOR Gates
A A
=
A
+
A
=
Y
 INVERTER
A
B
B
A 
B
+
A
=
Y
OR

A
B
A
B
B
+
A
=
Y
AND

 Similarly, it can be shown that NOR gates can be arranged to implement
any of the Boolean operations. See fig. below

25
XOR and XNOR Logic Circuits
 Two special logic circuits that
occur quite often in digital
systems are the exclusive-OR and
exclusive NOR circuits.
Exclusive OR
 Consider the logic circuit of fig (a) .
 The output expression of this circuit
is
 The accompanying truth table
shows that x= 1 for two cases:
A= 0, B= 1 (the term) and
A= 1, B= 0 (the term).
 In other words, this circuit produces
a HIGH output whenever the two
inputs are at opposite levels.
 This is the exclusive OR circuit,
which will hereafter be abbreviated
XOR.
 This particular combination of logic
gates occurs quite often and is very
useful in certain applications.
A
B B
A
+
B
A
=
Y
B
A
B
A
A B Y
0
0
1
1
0
1
0
1
0
1
1
0
B
A
B
A
Fig. (a)
B
A
+
B
A
=
Y

26
 In fact, the XOR circuit has been given
a symbol of its own as shown in fig
below
 This XOR circuit is commonly referred
to as an XOR gate, and we consider it
as another type of logic gate.
 An XOR gate has only two inputs; there
are no three-input or four- input XOR
gates.
 A short hand way that is sometimes
used to indicate the XOR output
expression is Y= AB.
 Where, the symbol  represents the
XOR gate operation.
 The characteristics of an XOR gate are
summarized as follows:
1. It has only two inputs and its output is
2. Its output is HIGH only when the two
inputs are at different levels
A
B
B
A
+
B
A
=
B
⊕
A
=
Y
B
⊕
A
=
B
A
+
B
A
=
Y

27
Exclusive –NOR
 The exclusive-NOR circuit
(Abbreviated XNOR) operates
completely opposite to the XOR
circuit.
 The fig (a) drawn below, shows an
X-NOR circuit and its accompanying
truth table.
 The output expression is
 Which indicates along with the truth
table that Y will be 1 for two cases:
 A=B=1 (the AB term) and
 A=B=0 (the term).
 In other words, this circuit produces
a HIHG output whenever the two
inputs are at the same level.
 In should be apparent that the output
of the XNOR circuit is the exact
inverse of the output of the XOR
B
A
+
B
A
=
Y
A
B B
A
+
B
A
=
Y
B
A
B
A
A B Y
0
0
1
1
0
1
0
1
1
0
0
1
B
A 
Fig.(a)

28
 The traditional symbol for an
XNOR gate is obtained by simply
adding a small circle at the out
put of the XOR symbol.
 A shorthand way to indicate the
output expression of the XNOR is
 This is simply the inverse of the
XOR operation.
 The XNOR gate is summarized as
follows:
1. It has only two inputs and its
output is
2. Its output is HIGH only when the
two input are the same level.
A
B
AB
+
B
A
=
B
⊕
A
=
Y
B
⊕
A
=
Y
B
⊕
A
=
B
A
+
B
A
=
Y

29
DESCRIBING LOGIC CIRCUITS ALGEBRAICALLY
Any logic circuit, no matter how complex,
may be completely described using the
Boolean operations previously defined,
because the OR gate, AND gate, and NOT
circuit are the basic building blocks of
digital systems.
For example, consider the circuit in Figure
(a)
This circuit has three inputs, A, B, and C
and a single output, Y.
Utilizing the Boolean expression for each
gate, we can easily determine the
expression for the output.
Occasionally, there may be confusion as
which operation to be performed first. The
expression Y=AB+C can be interpreted in
two different ways:
 A. B is ORed with C
 A is ANDed with the term B+C
To avoid this confusion, it will be
understood that if an expression contains
both AND and OR operations the AND
A
B
C
A.B Y=A.B+C
(a) Logic circuit which does
not require parenthesis
A
B
C
Y=(A+B).C
A+B
(b) Logic circuit requires
parenthesis

30
EVALUATING LOGIC–CIRCUIT OUTPUTS
 Once the Boolean expression for a
circuit output has been obtained, the
output logic level can be determined for
any set of input levels
 For example: suppose that we want to
know the logic level of the output Y for
the circuit in Figure (a) for the case
where A=0, B=1, C=1, and D=1.
 As in ordinary algebra, the value of Y
can be found by ‘plugging’ the values
of the variables into the expression
In general, the following rules must
always be followed when evaluated a
Boolean expression
1. First ,perform all inversions of single
terms; that is
2. Then perform all operations within
parentheses.
A
D
C
B
2
1
A
BC
A
D
A  D
A 
 
D
A
BC
A
Y 

(a)
( )
1
+
0
.
1
.
1
.
0
=
 
D
A
BC
A
Y 

( )
1
.
1
.
1
.
1
=
0
=
0
=
1
or
1
=
0

31
Determining output level from a Diagram
The output logic level for given input levels can also be
determined directly from the circuit diagram without using the
Boolean expression.
Technicians often use this technique during the
troubleshooting or testing of logic system since it also tells them
what each gate output is supposed to be as well as the final
output.
A=0
D=1
C=1
B=1 1
2
1
1
0
1
1 0
Y=0

THANK YOU!!!
ANY Question???
32

chapter3.pptx electrical engineering for university

More Related Content

Similar to chapter3.pptx electrical engineering for university (20)

Recently uploaded (20)

chapter3.pptx electrical engineering for university