Cisco CCNAX .200 120

Cisco 200-120 Exam Questions & Answers
Number: 200-120
Passing Score: 800
Time Limit: 120 min
File Version: 28.4
Cisco 200-120 Exam Questions & Answers
Exam Name: CCNA Cisco Certified Network Associate CCNA (803)

Certkiller
QUESTION 1
Refer to the exhibit.
What will Router1 do when it receives the data frame shown? (Choose three.)
A. Router1 will strip off the source MAC address and replace it with the MAC address 0000.0c36.6965.
B. Router1 will strip off the source IP address and replace it with the IP address 192.168.40.1.
C. Router1 will strip off the destination MAC address and replace it with the MAC address 0000.0c07.4320.
D. Router1 will strip off the destination IP address and replace it with the IP address of 192.168.40.1.
E. Router1 will forward the data packet out interface FastEthernet0/1.
F. Router1 will forward the data packet out interface FastEthernet0/2.
Correct Answer: ACF
Section: (none)
Explanation
Explanation/Reference:
Explanation:
QUESTION 2
"Pass Any Exam. Any Time." - www.actualtests.com 2
Cisco 200-120 Exam
Which three statements correctly describe Network Device A? (Choose three.)
A. With a network wide mask of 255.255.255.128, each interface does not require an IP address.
B. With a network wide mask of 255.255.255.128, each interface does require an IP address on a unique IP subnet.
C. With a network wide mask of 255.255.255.0, must be a Layer 2 device for the PCs to communicate with each other.
D. With a network wide mask of 255.255.255.0, must be a Layer 3 device for the PCs to communicate with each other.
E. With a network wide mask of 255.255.254.0, each interface does not require an IP address.
Correct Answer: BDE
Section: (none)
Explanation
Explanation:
QUESTION 3
Which of the following describes the roles of devices in a WAN? (Choose three.)
A. A CSU/DSU terminates a digital local loop.
B. A modem terminates a digital local loop.
C. A CSU/DSU terminates an analog local loop.
D. A modem terminates an analog local loop.
E. A router is commonly considered a DTE device.
F. A router is commonly considered a DCE device.
Correct Answer: ADE
Section: (none)
Explanation

Explanation:
QUESTION 4
Host A pings interface S0/0 on router 3. What is the TTL value for that ping?
A. 252
B. 253
Cisco 200-120 Exam
C. 254
D. 255
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 5
A network administrator is verifying the configuration of a newly installed host by establishing an FTP connection to a remote server. What is the highest layer of
the protocol stack that the network administrator is using for this operation?
A. application
B. presentation
C. session
D. transport
E. internet
F. data link
Correct Answer: A
Section: (none)
Explanation
Explanation:
QUESTION 6
A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the
network interface port?
A. This is a 10 Mb/s switch port.
B. This is a 100 Mb/s switch port.
C. This is an Ethernet port operating at half duplex.
D. This is an Ethernet port operating at full duplex.
E. This is a port on a network interface card in a PC.
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 7
A receiving host computes the checksum on a frame and determines that the frame is damaged. The frame is then discarded. At which OSI layer did this happen?

A. session
B. transport
C. network
D. data link
E. physical
Cisco 200-120 Exam
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 8
Which of the following correctly describe steps in the OSI data encapsulation process? (Choose two.)
A. The transport layer divides a data stream into segments and may add reliability and flow control information.
B. The data link layer adds physical source and destination addresses and an FCS to the segment.
C. Packets are created when the network layer encapsulates a frame with source and destination host addresses and protocol-related control information.
D. Packets are created when the network layer adds Layer 3 addresses and control information to a segment.
E. The presentation layer translates bits into voltages for transmission across the physical link.
Correct Answer: AD
Section: (none)
Explanation
Explanation:
QUESTION 9
What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN? (Choose two.)
A. The number of collision domains would remain the same.
B. The number of collision domains would decrease.
C. The number of collision domains would increase.
D. The number of broadcast domains would remain the same.
E. The number of broadcast domains would decrease.
F. The number of broadcast domains would increase.
Correct Answer: CD
Section: (none)
Explanation
Explanation:
Cisco 200-120 Exam
QUESTION 10
Which three statements accurately describe Layer 2 Ethernet switches? (Choose three.)
A. Spanning Tree Protocol allows switches to automatically share VLAN information.
B. Establishing VLANs increases the number of broadcast domains.
C. Switches that are configured with VLANs make forwarding decisions based on both Layer 2 and Layer 3 address information.
D. Microsegmentation decreases the number of collisions on the network.
E. In a properly functioning network with redundant switched paths, each switched segment will contain one root bridge with all its ports in the forwarding state. All
other switches in that broadcast domain will have only one root port.
F. If a switch receives a frame for an unknown destination, it uses ARP to resolve the address.
Correct Answer: BDE
Section: (none)
Explanation
Explanation:
QUESTION 11
Where does routing occur within the DoD TCP/IP reference model?

A. application
B. internet
C. network
D. transport
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 12
Refer to exhibit:
Cisco 200-120 Exam
Which destination addresses will be used by Host A to send data to Host C? (Choose two.)
A. the IP address of Switch 1
B. the MAC address of Switch 1
C. the IP address of Host C
D. the MAC address of Host C
E. the IP address of the router's E0 interface
F. the MAC address of the router's E0 interface
Correct Answer: CF
Section: (none)
Explanation
Explanation:
QUESTION 13
For what two purposes does the Ethernet protocol use physical addresses? (Choose two.)
A. to uniquely identify devices at Layer 2
B. to allow communication with devices on a different network
C. to differentiate a Layer 2 frame from a Layer 3 packet
D. to establish a priority system to determine which device gets to transmit first
E. to allow communication between different devices on the same network
F. to allow detection of a remote device when its physical address is unknown
Correct Answer: AE
Section: (none)
Explanation
Explanation:
Cisco 200-120 Exam
QUESTION 14
Based on the information given, which switch will be elected root bridge and why?
A. Switch A, because it has the lowest MAC address
B. Switch A, because it is the most centrally located switch

C. Switch B, because it has the highest MAC address
D. Switch C, because it is the most centrally located switch
E. Switch C, because it has the lowest priority
F. Switch D, because it has the highest priority
Correct Answer: E
Section: (none)
Explanation
Explanation:
QUESTION 15
Switch-1 needs to send data to a host with a MAC address of 00b0.d056.efa4. What will Switch-1 do with this data?
A. Switch-1 will drop the data because it does not have an entry for that MAC address.
B. Switch-1 will flood the data out all of its ports except the port from which the data originated.
C. Switch-1 will send an ARP request out all its ports except the port from which the data originated.
D. Switch-1 will forward the data to its default gateway.
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 16
What is the function of the command switchport trunk native vlan 999 on a Cisco Catalyst switch?
A. It creates a VLAN 999 interface.
B. It designates VLAN 999 for untagged traffic.
C. It blocks VLAN 999 traffic from passing on the trunk.
D. It designates VLAN 999 as the default for all unknown tagged traffic.
Correct Answer: B
Section: (none)
Explanation
Cisco 200-120 Exam
Explanation:
QUESTION 17
Which two protocols are used by bridges and/or switches to prevent loops in a layer 2 network? (Choose two.)
A. 802.1d
B. VTP
C. 802.1q
D. STP
E. SAP
Correct Answer: AD
Section: (none)
Explanation
Explanation:
QUESTION 18
Which switch would STP choose to become the root bridge in the selection process?
A. 32768: 11-22-33-44-55-66
B. 32768: 22-33-44-55-66-77
C. 32769: 11-22-33-44-55-65
D. 32769: 22-33-44-55-66-78

Correct Answer: A
Section: (none)
Explanation
Explanation:
QUESTION 19
A switch is configured with all ports assigned to vlan 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch
ports to a new VLAN on the switch?
A. More collision domains will be created.
B. IP address utilization will be more efficient.
C. More bandwidth will be required than was needed previously.
D. An additional broadcast domain will be created.
Cisco 200-120 Exam
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 20
What are three benefits of implementing VLANs? (Choose three.)
A. A higher level of network security can be reached by separating sensitive data traffic from other network traffic.
B. A more efficient use of bandwidth can be achieved allowing many physical groups to use the same network infrastructure.
C. A more efficient use of bandwidth can be achieved allowing many logical networks to use the same network infrastructure.
D. Broadcast storms can be mitigated by increasing the number of broadcast domains, thus reducing their size.
E. Broadcast storms can be mitigated by decreasing the number of broadcast domains, thus increasing their size.
F. VLANs make it easier for IT staff to configure new logical groups, because the VLANs all belong to the same broadcast domain.
G. Port-based VLANs increase switch-port use efficiency, thanks to 802.1Q trunks.
Correct Answer: ACD
Section: (none)
Explanation
Explanation:
QUESTION 21
Cisco 200-120 Exam
Which of the following are benefits of VLANs? (Choose three.)
A. They increase the size of collision domains.
B. They allow logical grouping of users by function.
C. They can enhance network security.
D. They increase the size of broadcast domains while decreasing the number of collision domains.
E. They increase the number of broadcast domains while decreasing the size of the broadcast domains.
F. They simplify switch administration.
Correct Answer: BCE
Section: (none)
Explanation
Explanation:
QUESTION 22
A technician has installed SwitchB and needs to configure it for remote access from the management workstation connected to SwitchA. Which set of commands
is required to accomplish this task?
A. SwitchB(config)# interface FastEthernet 0/1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown
B. SwitchB(config)# interface vlan 1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 "Pass Any Exam. Any Time." - www.actualtests.com 16

Cisco 200-120 Exam
SwitchB(config-if)# ip default-gateway 192.168.8.254 255.255.255.0 SwitchB(config-if)# no shutdown
C. SwitchB(config)# ip default-gateway 192.168.8.254
SwitchB(config)# interface vlan 1
D. SwitchB(config)# ip default-network 192.168.8.254
SwitchB(config)# interface vlan 1
E. SwitchB(config)# ip route 192.168.8.254 255.255.255.0 SwitchB(config)# interface FastEthernet 0/1
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 23
In an Ethernet network, under what two scenarios can devices transmit? (Choose two.)
A. when they receive a special token
B. when there is a carrier
C. when they detect no other devices are sending
D. when the medium is idle
E. when the server grants access
Correct Answer: CD
Section: (none)
Explanation
Explanation:
QUESTION 24
Which two commands can be used to verify a trunk link configuration status on a given Cisco switch interface? (Choose two.)
A. show interface trunk
B. show interface interface
C. show ip interface brief
D. show interface vlan
E. show interface switchport
Correct Answer: AE
Section: (none)
Explanation
Explanation:
QUESTION 25
Which command enables RSTP on a switch?
A. spanning-tree uplinkfast
B. spanning-tree mode rapid-pvst
C. spanning-tree backbonefast
D. spanning-tree mode mst
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 26
Cisco 200-120 Exam

All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to
SwitchB. Based on the output shown, what is the most likely problem?
A. The access link needs to be configured in multiple VLANs.
B. The link between the switches is configured in the wrong VLAN.
C. The link between the switches needs to be configured as a trunk.
D. VTP is not configured to carry VLAN information between the switches.
E. Switch IP addresses must be configured in order for traffic to be forwarded between the switches.
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 27
What is the function of the command switchport trunk native vlan 999 on a Cisco Catalyst switch?
A. It creates a VLAN 999 interface.
B. It designates VLAN 999 for untagged traffic.
C. It blocks VLAN 999 traffic from passing on the trunk.
Cisco 200-120 Exam
D. It designates VLAN 999 as the default for all unknown tagged traffic.
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 28
Given the output shown from this Cisco Catalyst 2950, what is the reason that interface FastEthernet 0/10 is not the root port for VLAN 2?
A. This switch has more than one interface connected to the root network segment in VLAN 2.
B. This switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree.
C. This switch interface has a higher path cost to the root bridge than another in the topology.
D. This switch has a lower bridge ID for VLAN 2 than the elected designated switch.
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 29
Why will a switch never learn a broadcast address?
A. Broadcasts only use network layer addressing.

B. A broadcast frame is never forwarded by a switch.
C. A broadcast address will never be the source address of a frame.
D. Broadcast addresses use an incorrect format for the switching table.
E. Broadcast frames are never sent to switches.
Correct Answer: C
Section: (none)
Explanation
Cisco 200-120 Exam
Explanation:
QUESTION 30
Why has this switch not been elected the root bridge for VLAN1?
A. It has more than one interface that is connected to the root network segment.
B. It is running RSTP while the elected root bridge is running 802.1d spanning tree.
C. It has a higher MAC address than the elected root bridge.
D. It has a higher bridge ID than the elected root bridge.
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 31
Which two link protocols are used to carry multiple VLANs over a single link? (Choose two.)
A. VTP
B. 802.1q
C. IGP
Cisco 200-120 Exam
D. ISL
E. 802.3u
Correct Answer: BD
Section: (none)
Explanation
Explanation:
QUESTION 32
Assuming the default switch configuration, which VLAN range can be added, modified, and removed on a Cisco switch?
A. 1 through 1001
B. 2 through 1001
C. 1 through 1002
D. 2 through 1005
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 33
Which statement about VLAN operation on Cisco Catalyst switches is true?

A. When a packet is received from an 802.1Q trunk, the VLAN ID can be determined from the source MAC address and the MAC address table.
B. Unknown unicast frames are retransmitted only to the ports that belong to the same VLAN.
C. Broadcast and multicast frames are retransmitted to ports that are configured on different VLAN.
D. Ports between switches should be configured in access mode so that VLANs can span across the ports.
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 34
Refer to the topology shown in the exhibit.
Cisco 200-120 Exam
Which ports will be STP designated ports if all the links are operating at the same bandwidth? (Choose three.)
A. Switch A - Fa0/0
B. Switch A - Fa0/1
C. Switch B - Fa0/0
D. Switch B - Fa0/1
E. Switch C - Fa0/0
F. Switch C - Fa0/1
Correct Answer: BCD
Section: (none)
Explanation
Explanation:
QUESTION 35
Cisco 200-120 Exam
How should the FastEthernet0/1 ports on the 2950 model switches that are shown in the exhibit be configured to allow connectivity between all devices?
A. The ports only need to be connected by a crossover cable.
B. SwitchX(config)# interface fastethernet 0/1
SwitchX(config-if)# switchport mode trunk
C. SwitchX(config)# interface fastethernet 0/1
SwitchX(config-if)# switchport mode access
SwitchX(config-if)# switchport access vlan 1
D. SwitchX(config)# interface fastethernet 0/1
SwitchX(config-if)# switchport mode trunk
SwitchX(config-if)# switchport trunk vlan 1

Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 36
Cisco 200-120 Exam
A frame on VLAN 1 on switch S1 is sent to switch S2 where the frame is received on VLAN 2.
What causes this behavior?
A. trunk mode mismatches
B. allowing only VLAN 2 on the destination
C. native VLAN mismatches
D. VLANs that do not correspond to a unique IP subnet
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 37
Which three statements about RSTP are true? (Choose three.)
A. RSTP significantly reduces topology reconverging time after a link failure.
Cisco 200-120 Exam
B. RSTP expands the STP port roles by adding the alternate and backup roles.
C. RSTP port states are blocking, discarding, learning, or forwarding.
D. RSTP provides a faster transition to the forwarding state on point-to-point links than STP does.
E. RSTP also uses the STP proposal-agreement sequence.
F. RSTP uses the same timer-based process as STP on point-to-point links.
Correct Answer: ABD
Section: (none)
Explanation
Explanation:
QUESTION 38
At which layer of the OSI model is RSTP used to prevent loops?

A. physical
B. data link
C. network
D. transport
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 39
What does a Layer 2 switch use to decide where to forward a received frame?
A. source MAC address
B. source IP address
C. source switch port
D. destination IP address
E. destination port address
F. destination MAC address
Correct Answer: F
Section: (none)
Explanation
Explanation:
QUESTION 40
Cisco 200-120 Exam
Which statement is true?
A. The Fa0/11 role confirms that SwitchA is the root bridge for VLAN 20.
B. VLAN 20 is running the Per VLAN Spanning Tree Protocol.
C. The MAC address of the root bridge is 0017.596d.1580.
D. SwitchA is not the root bridge, because not all of the interface roles are designated.
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 41
Which two benefits are provided by creating VLANs? (Choose two.)
A. added security
B. dedicated bandwidth
C. provides segmentation
D. allows switches to route traffic between subinterfaces
E. contains collisions
Correct Answer: AC
Section: (none)
Explanation
Explanation:

QUESTION 42
Cisco 200-120 Exam
Which command can be used from a PC to verify the connectivity between hosts that connect through a switch in the same LAN?
A. pingaddress
B. tracertaddress
C. tracerouteaddress
D. arpaddress
Correct Answer: A
Section: (none)
Explanation
Explanation:
QUESTION 43
Based on the network shown in the graphic
Which option contains both the potential networking problem and the protocol or setting that should be used to prevent the problem?
A. routing loops, hold down timers
B. switching loops, split horizon
C. routing loops, split horizon
D. switching loops, VTP
E. routing loops, STP
F. switching loops, STP
Correct Answer: F
Section: (none)
Explanation
Explanation:
Cisco 200-120 Exam
QUESTION 44
Which two statements are true about interVLAN routing in the topology that is shown in the exhibit? (Choose two.)
A. Host E and host F use the same IP gateway address.
B. Router1 and Switch2 should be connected via a crossover cable.
C. Router1 will not play a role in communications between host A and host D.
D. The FastEthernet 0/0 interface on Router1 must be configured with subinterfaces.
E. Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit.
F. The FastEthernet 0/0 interface on Router1 and the FastEthernet 0/1 interface on Switch2 trunk ports must be configured using the same encapsulation type.
Correct Answer: DF
Section: (none)
Explanation
Explanation:

QUESTION 45
Which two of these are characteristics of the 802.1Q protocol? (Choose two.)
A. It is used exclusively for tagging VLAN frames and does not address network reconvergence "Pass Any Exam. Any Time." - www.actualtests.com 30
Cisco 200-120 Exam
following switched network topology changes.
B. It modifies the 802.3 frame header, and thus requires that the FCS be recomputed.
C. It is a Layer 2 messaging protocol which maintains VLAN configurations across networks.
D. It includes an 8-bit field which specifies the priority of a frame.
E. It is a trunking protocol capable of carrying untagged frames.
Correct Answer: BE
Section: (none)
Explanation
Explanation:
QUESTION 46
Each of these four switches has been configured with a hostname, as well as being configured to run RSTP. No other configuration changes have been made.
Which three of these show the correct RSTP port roles for the indicated switches and interfaces? (Choose three.)
A. SwitchA, Fa0/2, designated
B. SwitchA, Fa0/1, root
C. SwitchB, Gi0/2, root
D. SwitchB, Gi0/1, designated
E. SwitchC, Fa0/2, root
F. SwitchD, Gi0/2, root
Cisco 200-120 Exam
Correct Answer: ABF
Section: (none)
Explanation
Explanation:
QUESTION 47
The network administrator normally establishes a Telnet session with the switch from host A. However, host A is unavailable. The administrator's attempt to telnet
to the switch from host B fails, but pings to the other two hosts are successful. What is the issue?
A. Host B and the switch need to be in the same subnet.

B. The switch interface connected to the router is down.
C. Host B needs to be assigned an IP address in VLAN 1.
D. The switch needs an appropriate default gateway assigned.
E. The switch interfaces need the appropriate IP addresses assigned.
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 48
Cisco 200-120 Exam
Which switch provides the spanning-tree designated port role for the network segment that services the printers?
A. Switch1
B. Switch2
C. Switch3
D. Switch4
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 49
What is one benefit of PVST+?
A. PVST+ supports Layer 3 load balancing without loops.
B. PVST+ reduces the CPU cycles for all the switches in the network.
C. PVST+ allows the root switch location to be optimized per VLAN.
D. PVST+ automatically selects the root bridge location, to provide optimized bandwidth usage.
Correct Answer: C
Section: (none)
Explanation
Explanation:
Cisco 200-120 Exam
QUESTION 50
Which are valid modes for a switch port used as a VLAN trunk? (Choose three.)
A. transparent
B. auto
C. on
D. desirable
E. blocking
F. forwarding
Correct Answer: BCD
Section: (none)
Explanation
Explanation:

QUESTION 51
Refer to Exhibit:
How many broadcast domains are shown in the graphic assuming only the default VLAN is configured on the switches?
A. one
B. two
C. six
D. twelve
Correct Answer: A
Section: (none)
Explanation
Explanation:
Cisco 200-120 Exam
QUESTION 52
Which three of these statements regarding 802.1Q trunking are correct? (Choose three.)
A. 802.1Q native VLAN frames are untagged by default.
B. 802.1Q trunking ports can also be secure ports.
C. 802.1Q trunks can use 10 Mb/s Ethernet interfaces.
D. 802.1Q trunks require full-duplex, point-to-point connectivity.
E. 802.1Q trunks should have native VLANs that are the same at both ends.
Correct Answer: ACE
Section: (none)
Explanation
Explanation:
QUESTION 53
The output that is shown is generated at a switch. Which three statements are true? (Choose three.)
A. All ports will be in a state of discarding, learning, or forwarding.
B. Thirty VLANs have been configured on this switch.
C. The bridge priority is lower than the default value for spanning tree.
Cisco 200-120 Exam
D. All interfaces that are shown are on shared media.
E. All designated ports are in a forwarding state.
F. This switch must be the root bridge for all VLANs on this switch.
Correct Answer: ACE
Section: (none)
Explanation

Explanation:
Topic 2, Volume B
QUESTION 54
At the end of an RSTP election process, which access layer switch port will assume the discarding role?
A. Switch3, port fa0/1
B. Switch3, port fa0/12
C. Switch4, port fa0/11
D. Switch4, port fa0/2
E. Switch3, port Gi0/1
F. Switch3, port Gi0/2
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 55
Cisco 200-120 Exam
Which term describes a spanning-tree network that has all switch ports in either the blocking or fowarding state?
A. converged
B. redundant
C. provisioned
D. spanned
Correct Answer: A
Section: (none)
Explanation
Explanation:
QUESTION 56
What are the possible trunking modes for a switch port? (Choose three.)
A. transparent
B. auto
C. on
D. desirable
E. client
F. forwarding
Correct Answer: BCD
Section: (none)
Explanation
Explanation:
QUESTION 57
Which two of these statements regarding RSTP are correct? (Choose two.)
A. RSTP cannot operate with PVST+.
B. RSTP defines new port roles.
C. RSTP defines no new port states.
D. RSTP is a proprietary implementation of IEEE 802.1D STP.
E. RSTP is compatible with the original IEEE 802.1D STP.
Correct Answer: BE
Section: (none)

Explanation
Explanation:
Cisco 200-120 Exam
QUESTION 58
What are three advantages of VLANs? (Choose three.)
A. VLANs establish broadcast domains in switched networks.
B. VLANs utilize packet filtering to enhance network security.
C. VLANs provide a method of conserving IP addresses in large networks.
D. VLANs provide a low-latency internetworking alternative to routed networks.
E. VLANs allow access to network services based on department, not physical location.
F. VLANs can greatly simplify adding, moving, or changing hosts on the network.
Correct Answer: AEF
Section: (none)
Explanation
Explanation:
QUESTION 59
Which two benefits are provided by using a hierarchical addressing network addressing scheme? (Choose two.)
A. reduces routing table entries
B. auto-negotiation of media rates
C. efficient utilization of MAC addresses
D. dedicated communications between devices
E. ease of management and troubleshooting
Correct Answer: AE
Section: (none)
Explanation
Explanation:
QUESTION 60
Refer to the diagram.
All hosts have connectivity with one another. Which statements describe the addressing scheme that is in use in the network? (Choose three.)
A. The subnet mask in use is 255.255.255.192.
B. The subnet mask in use is 255.255.255.128.
C. The IP address 172.16.1.25 can be assigned to hosts in VLAN1
D. The IP address 172.16.1.205 can be assigned to hosts in VLAN1
E. The LAN interface of the router is configured with one IP address.
F. The LAN interface of the router is configured with multiple IP addresses.
Correct Answer: BCF
Section: (none)
Explanation
Explanation:
Cisco 200-120 Exam
QUESTION 61
Which two statements describe characteristics of IPv6 unicast addressing? (Choose two.)
A. Global addresses start with 2000::/3.
B. Link-local addresses start with FE00:/12.
C. Link-local addresses start with FF00::/10.
D. There is only one loopback address and it is ::1.
E. If a global address is assigned to an interface, then that is the only allowable address for the interface.

Correct Answer: AD
Section: (none)
Explanation
Explanation:
QUESTION 62
The network administrator has been asked to give reasons for moving from IPv4 to IPv6. What are two valid reasons for adopting IPv6 over IPv4? (Choose two.)
A. no broadcast
B. change of source address in the IPv6 header
C. change of destination address in the IPv6 header
D. Telnet access does not require a password
E. autoconfiguration
F. NAT
Correct Answer: AE
Section: (none)
Explanation
Explanation:
QUESTION 63
Which subnet mask would be appropriate for a network address range to be subnetted for up to eight LANs, with each LAN containing 5 to 26 hosts?
A. 0.0.0.240
B. 255.255.255.252
C. 255.255.255.0
D. 255.255.255.224
E. 255.255.255.240
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 64
What are three approaches that are used when migrating from an IPv4 addressing scheme to an IPv6 scheme. (Choose three.)
A. enable dual-stack routing
B. configure IPv6 directly
C. configure IPv4 tunnels between IPv6 islands
D. use proxying and translation to translate IPv6 packets into IPv4 packets
E. statically map IPv4 addresses to IPv6 addresses
F. use DHCPv6 to map IPv4 addresses to IPv6 addresses
Correct Answer: ACD
Section: (none)
Explanation
Explanation:
QUESTION 65
In this VLSM addressing scheme, what summary address would be sent from router A?
Cisco 200-120 Exam
A. 172.16.0.0 /16
B. 172.16.0.0 /20
C. 172.16.0.0 /24
D. 172.32.0.0 /16

E. 172.32.0.0 /17
F. 172.64.0.0 /16
Correct Answer: A
Section: (none)
Explanation
Explanation:
QUESTION 66
Cisco 200-120 Exam
What is the most efficient summarization that R1 can use to advertise its networks to R2?
A. 172.1.0.0/22
B. 172.1.0.0/21
C. 172.1.4.0/22
D. 172.1.4.0/24
172.1.5.0/24
172.1.6.0/24
172.1.7.0/24
E. 172.1.4.0/25
172.1.4.128/25
172.1.5.0/24
172.1.6.0/24
172.1.7.0/24
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 67
Which option is a valid IPv6 address?
A. 2001:0000:130F::099a::12a
B. 2002:7654:A1AD:61:81AF:CCC1
C. FEC0:ABCD:WXYZ:0067::2A4
D. 2004:1:25A4:886F::1
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 68
Which three are characteristics of an IPv6 anycast address? (Choose three.)
A. one-to-many communication model
B. one-to-nearest communication model
C. any-to-many communication model
D. a unique IPv6 address for each device in the group
E. the same address for multiple devices in the group
F. delivery of packets to the group interface that is closest to the sending device "Pass Any Exam. Any Time." - www.actualtests.com 45
Cisco 200-120 Exam
Correct Answer: BEF
Section: (none)
Explanation
Explanation:
QUESTION 69
A national retail chain needs to design an IP addressing scheme to support a nationwide network. The company needs a minimum of 300 sub-networks and a
maximum of 50 host addresses per subnet. Working with only one Class B address, which of the following subnet masks will support an appropriate addressing
scheme? (Choose two.)

A. 255.255.255.0
B. 255.255.255.128
C. 255.255.252.0
D. 255.255.255.224
E. 255.255.255.192
F. 255.255.248.0
Correct Answer: BE
Section: (none)
Explanation
Explanation:
QUESTION 70
A network administrator is adding two new hosts to SwitchA. Which three values could be used for the configuration of these hosts? (Choose three.)
Cisco 200-120 Exam
A. host A IP address: 192.168.1.79
B. host A IP address: 192.168.1.64
C. host A default gateway: 192.168.1.78
D. host B IP address: 192.168.1.128
E. host B default gateway: 192.168.1.129
F. host B IP address: 192.168.1.190
Correct Answer: ACF
Section: (none)
Explanation
Explanation:
QUESTION 71
Which IPv6 address is the all-router multicast group?
A. FF02::1
B. FF02::2
C. FF02::3
D. FF02::4
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 72
Which IPv6 address is valid?
A. 2001:0db8:0000:130F:0000:0000:08GC:140B
B. 2001:0db8:0:130H::87C:140B
C. 2031::130F::9C0:876A:130B
D. 2031:0:130F::9C0:876A:130B
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 73
Which of these represents an IPv6 link-local address?

A. FE80::380e:611a:e14f:3d69
B. FE81::280f:512b:e14f:3d69
Cisco 200-120 Exam
C. FEFE:0345:5f1b::e14d:3d69
D. FE08::280e:611:a:f14f:3d69
Correct Answer: A
Section: (none)
Explanation
Explanation:
QUESTION 74
The network administrator is asked to configure 113 point-to-point links. Which IP addressing scheme defines the address range and subnet mask that meet the
requirement and waste the fewest subnet and host addresses?
A. 10.10.0.0/16 subnetted with mask 255.255.255.252
B. 10.10.0.0/18 subnetted with mask 255.255.255.252
C. 10.10.1.0/24 subnetted with mask 255.255.255.252
D. 10.10.0.0/23 subnetted with mask 255.255.255.252
E. 10.10.1.0/25 subnetted with mask 255.255.255.252
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 75
Cisco 200-120 Exam
What is the meaning of the output MTU 1500 bytes?
A. The maximum number of bytes that can traverse this interface per second is 1500.
B. The minimum segment size that can traverse this interface is 1500 bytes.
C. The maximum segment size that can traverse this interface is 1500 bytes.
D. The minimum packet size that can traverse this interface is 1500 bytes.
E. The maximum packet size that can traverse this interface is 1500 bytes.
F. The maximum frame size that can traverse this interface is 1500 bytes.
Correct Answer: E
Section: (none)
Explanation
Explanation:
QUESTION 76
Which command displays CPU utilization?
A. show protocols
B. show process
Cisco 200-120 Exam
C. show system
D. show version
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 77
What two things will a router do when running a distance vector routing protocol? (Choose two.)
A. Send periodic updates regardless of topology changes.
B. Send entire routing table to all routers in the routing domain.
C. Use the shortest-path algorithm to the determine best path.
D. Update the routing table based on updates from their neighbors.

E. Maintain the topology of the entire network in its database.
Correct Answer: AD
Section: (none)
Explanation
Explanation:
QUESTION 78
Which command is used to display the collection of OSPF link states?
A. show ip ospf link-state
B. show ip ospf lsa database
C. show ip ospf neighbors
D. show ip ospf database
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 79
Cisco 200-120 Exam
The technician wants to upload a new IOS in the router while keeping the existing IOS. What is the maximum size of an IOS file that could be loaded if the original
IOS is also kept in flash?
A. 3 MB
B. 4 MB
C. 5 MB
D. 7 MB
E. 8 MB
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 80
The two exhibited devices are the only Cisco devices on the network. The serial network between
Cisco 200-120 Exam
the two devices has a mask of 255.255.255.252. Given the output that is shown, what three statements are true of these devices? (Choose three.)
A. The Manchester serial address is 10.1.1.1.
B. The Manchester serial address is 10.1.1.2.
C. The London router is a Cisco 2610.
D. The Manchester router is a Cisco 2610.
E. The CDP information was received on port Serial0/0 of the Manchester router.
F. The CDP information was sent by port Serial0/0 of the London router.

Correct Answer: ACE
Section: (none)
Explanation
Explanation:
QUESTION 81
If IP routing is enabled, which two commands set the gateway of last resort to the default gateway? (Choose two.)
A. ip default-gateway 0.0.0.0
B. ip route 172.16.2.1 0.0.0.0 0.0.0.0
C. ip default-network 0.0.0.0
D. ip default-route 0.0.0.0 0.0.0.0 172.16.2.1
E. ip route 0.0.0.0 0.0.0.0 172.16.2.1
Correct Answer: CE
Section: (none)
Explanation
Explanation:
QUESTION 82
Which parameter would you tune to affect the selection of a static route as a backup, when a dynamic protocol is also being used?
A. hop count
B. administrative distance
C. link bandwidth
D. link delay
E. link cost
Correct Answer: B
Section: (none)
Explanation
Explanation:
Cisco 200-120 Exam
QUESTION 83
A network associate has configured OSPF with the command:
City(config-router)# network 192.168.12.64 0.0.0.63 area 0
After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit
will participate in OSPF according to this configuration statement? (Choose three.)
A. FastEthernet0 /0
B. FastEthernet0 /1
C. Serial0/0
D. Serial0/1.102
E. Serial0/1.103
F. Serial0/1.104
Correct Answer: BCD
Section: (none)
Explanation
Explanation:
QUESTION 84
Cisco 200-120 Exam

The Lakeside Company has the internetwork in the exhibit. The administrator would like to reduce the size of the routing table on the Central router. Which partial
routing table entry in the Central router represents a route summary that represents the LANs in Phoenix but no additional subnets?
A. 10.0.0.0/22 is subnetted, 1 subnets
D 10.0.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
B. 10.0.0.0/28 is subnetted, 1 subnets
D 10.2.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
C. 10.0.0.0/30 is subnetted, 1 subnets
D 10.2.2.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
D. 10.0.0.0/22 is subnetted, 1 subnets
D 10.4.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
E. 10.0.0.0/28 is subnetted, 1 subnets
D 10.4.4.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
F. 10.0.0.0/30 is subnetted, 1 subnets
D 10.4.4.4 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 85
Cisco 200-120 Exam
Refer to the graphic.
A static route to the 10.5.6.0/24 network is to be configured on the HFD router. Which commands will accomplish this? (Choose two.)
A. HFD(config)# ip route 10.5.6.0 0.0.0.255 fa0/0
B. HFD(config)# ip route 10.5.6.0 0.0.0.255 10.5.4.6
C. HFD(config)# ip route 10.5.6.0 255.255.255.0 fa0/0
D. HFD(config)# ip route 10.5.6.0 255.255.255.0 10.5.4.6
E. HFD(config)# ip route 10.5.4.6 0.0.0.255 10.5.6.0
F. HFD(config)# ip route 10.5.4.6 255.255.255.0 10.5.6.0
Correct Answer: CD
Section: (none)
Explanation
Explanation:
QUESTION 86
Before installing a new, upgraded version of the IOS, what should be checked on the router, and which command should be used to gather this information?
(Choose two.)
A. the amount of available ROM
B. the amount of available flash and RAM memory
C. the version of the bootstrap software present on the router

D. show version
E. show processes
F. show running-config
Correct Answer: BD
Section: (none)
Explanation
Explanation:
Cisco 200-120 Exam
QUESTION 87
Which command reveals the last method used to powercycle a router?
A. show reload
B. show boot
C. show running-config
D. show version
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 88
Which command would you use on a Cisco router to verify the Layer 3 path to a host?
A. tracert address
B. traceroute address
C. telnet address
D. ssh address
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 89
What information does a router running a link-state protocol use to build and maintain its topological database? (Choose two.)
A. hello packets
B. SAP messages sent by other routers
C. LSAs from other routers
D. beacons received on point-to-point links
E. routing tables received from other link-state routers
F. TTL packets from designated routers
Correct Answer: AC
Section: (none)
Explanation
Cisco 200-120 Exam
Explanation:
QUESTION 90
Which statements describe the routing protocol OSPF? (Choose three.)
A. It supports VLSM.
B. It is used to route between autonomous systems.
C. It confines network instability to one area of the network.
D. It increases routing overhead on the network.
E. It allows extensive control of routing updates.
F. It is simpler to configure than RIP v2.
Correct Answer: ACE
Section: (none)
Explanation
Explanation:
QUESTION 91

A network administrator configures a new router and enters the copy startup-config running-config command on the router. The network administrator powers
down the router and sets it up at a remote location. When the router starts, it enters the system configuration dialog as shown. What is the cause of the problem?
A. The network administrator failed to save the configuration.
B. The configuration register is set to 0x2100.
C. The boot system flash command is missing from the configuration.
D. The configuration register is set to 0x2102.
E. The router is configured with the boot system startup command.
Correct Answer: A
Section: (none)
Explanation
Cisco 200-120 Exam
Explanation:
QUESTION 92
Which WAN protocol is being used?
A. ATM
B. HDLC
C. Frame Relay
D. PPP
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 93
Which characteristics are representative of a link-state routing protocol? (Choose three.)
A. provides common view of entire topology
B. exchanges routing tables with neighbors
C. calculates shortest path
D. utilizes event-triggered updates
E. utilizes frequent periodic updates
Correct Answer: ACD
Section: (none)
Explanation
Explanation:
QUESTION 94

C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The
hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?
A. These commands need to be added to the configuration:
C-router(config)# router eigrp 123
C-router(config-router)# network 172.19.0.0
B. These commands need to be added to the configuration:
C-router(config)# router ospf 1
C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0
C. These commands need to be added to the configuration:
C-router(config)# router rip
C-router(config-router)# network 172.19.0.0
D. No further routing configuration is required.
Cisco 200-120 Exam
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 95
Why is flash memory erased prior to upgrading the IOS image from the TFTP server?
A. The router cannot verify that the Cisco IOS image currently in flash is valid.
B. Flash memory on Cisco routers can contain only a single IOS image.
C. Erasing current flash content is requested during the copy dialog.
D. In order for the router to use the new image as the default, it must be the only IOS image in flash.
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 96

According to the routing table, where will the router send a packet destined for 10.1.5.65?
A. 10.1.1.2
B. 10.1.2.2
C. 10.1.3.3
D. 10.1.4.4
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 97
Which two locations can be configured as a source for the IOS image in the boot system command? (Choose two.)
A. RAM
B. NVRAM
C. flash memory
D. HTTP server
E. TFTP server
F. Telnet server
Correct Answer: CE
Section: (none)
Explanation
Explanation:
QUESTION 98
What commands must be configured on the 2950 switch and the router to allow communication between host 1 and host 2? (Choose two.)
A. Router(config)# interface fastethernet 0/0
Router(config-if)# ip address 192.168.1.1 255.255.255.0 Router(config-if)# no shut down
B. Router(config)# interface fastethernet 0/0
Router(config-if)# no shut down
Router(config)# interface fastethernet 0/0.1
Router(config-subif)# encapsulation dot1q 10
Router(config-subif)# ip address 192.168.10.1 255.255.255.0 Router(config)# interface fastethernet 0/0.2
Cisco 200-120 Exam
Router(config-subif)# encapsulation dot1q 20
Router(config-subif)# ip address 192.168.20.1 255.255.255.0
C. Router(config)# router eigrp 100
Router(config-router)# network 192.168.10.0
Router(config-router)# network 192.168.20.0
D. Switch1(config)# vlan database
Switch1(config-vlan)# vtp domain XYZ
Switch1(config-vlan)# vtp server
E. Switch1(config)# interface fastethernet 0/1

Switch1(config-if)# switchport mode trunk
F. Switch1(config)# interface vlan 1
Switch1(config-if)# ip default-gateway 192.168.1.1
Correct Answer: BE
Section: (none)
Explanation
Explanation:
QUESTION 99
Which two statements describe the process identifier that is used in the command to configure OSPF on a router? (Choose two.)
Router(config)# router ospf 1
A. All OSPF routers in an area must have the same process ID.
B. Only one process number can be used on the same router.
C. Different process identifiers can be used to run multiple OSPF processes
D. The process number can be any number from 1 to 65,535.
E. Hello packets are sent to each neighbor to determine the processor identifier.
Correct Answer: CD
Section: (none)
Explanation
Explanation:
QUESTION 100
Cisco 200-120 Exam
For what two reasons has the router loaded its IOS image from the location that is shown? (Choose two.)
A. Router1 has specific boot system commands that instruct it to load IOS from a TFTP server.
B. Router1 is acting as a TFTP server for other routers.
C. Router1 cannot locate a valid IOS image in flash memory.
D. Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.
E. Cisco routers will first attempt to load an image from TFTP for management purposes.
Correct Answer: AC
Section: (none)
Explanation
Explanation:
QUESTION 101
Which three elements must be used when you configure a router interface for VLAN trunking? (Choose three.)
A. one physical interface for each subinterface
B. one IP network or subnetwork for each subinterface
C. a management domain for each subinterface
D. subinterface encapsulation identifiers that match VLAN tags
E. one subinterface per VLAN
F. subinterface numbering that matches VLAN tags
Correct Answer: BDE
Section: (none)
Explanation
Explanation:

QUESTION 102
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0? (Choose two.)
A. Router(config)# router ospf 0
B. Router(config)# router ospf 1
C. Router(config)# router ospf area 0
D. Router(config-router)# network 192.168.16.0 0.0.0.255 0
E. Router(config-router)# network 192.168.16.0 0.0.0.255 area 0
F. Router(config-router)# network 192.168.16.0 255.255.255.0 area 0
Correct Answer: BE
Section: (none)
Explanation
Explanation:
Cisco 200-120 Exam
QUESTION 103
What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router?
A. 2
B. 4
C. 16
D. unlimited
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 104
Which command shows your active Telnet connections?
A. show cdp neigbors
B. show session
C. show users
D. show vty logins
Correct Answer: B
Section: (none)
Explanation
Explanation:
Cisco 200-120 Exam
QUESTION 105
Which type of EIGRP route entry describes a feasible successor?
A. a backup route, stored in the routing table
B. a primary route, stored in the routing table
C. a backup route, stored in the topology table
D. a primary route, stored in the topology table
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 106

What statement is true of the configuration for this network?
A. The configuration that is shown provides inadequate outside address space for translation of the number of inside addresses that are supported.
B. Because of the addressing on interface FastEthernet0/1, the Serial0/0 interface address will not support the NAT configuration as shown.
Cisco 200-120 Exam
C. The number 1 referred to in the ip nat inside source command references access-list number 1.
D. ExternalRouter must be configured with static routes to networks 172.16.1.0/24 and 172.16.2.0/24.
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 107
Which statement describes the process of dynamically assigning IP addresses by the DHCP server?
A. Addresses are allocated after a negotiation between the server and the host to determine the length of the agreement.
B. Addresses are permanently assigned so that the hosts uses the same address at all times.
C. Addresses are assigned for a fixed period of time, at the end of the period, a new request for an address must be made.
D. Addresses are leased to hosts, which periodically contact the DHCP server to renew the lease.
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 108
What are two benefits of using NAT? (Choose two.)
A. NAT facilitates end-to-end communication when IPsec is enabled.
B. NAT eliminates the need to re-address all hosts that require external access.
C. NAT conserves addresses through host MAC-level multiplexing.
D. Dynamic NAT facilitates connections from the outside of the network.
E. NAT accelerates the routing process because no modifications are made on the packets.
F. NAT protects network security because private networks are not advertised.
Correct Answer: BF
Section: (none)
Explanation
Explanation:
QUESTION 109
On which options are standard access lists based?
Cisco 200-120 Exam
A. destination address and wildcard mask
B. destination address and subnet mask
C. source address and subnet mask
D. source address and wildcard mask
Correct Answer: D

Section: (none)
Explanation
Explanation:
QUESTION 110
A network engineer wants to allow a temporary entry for a remote user with a specific username and password so that the user can access the entire network over
the Internet. Which ACL can be used?
A. standard
B. extended
C. dynamic
D. reflexive
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 111
How does a DHCP server dynamically assign IP addresses to hosts?
A. Addresses are permanently assigned so that the host uses the same address at all times.
B. Addresses are assigned for a fixed period of time. At the end of the period, a new request for an address must be made, and another address is then assigned.
C. Addresses are leased to hosts. A host will usually keep the same address by periodically contacting the DHCP server to renew the lease.
D. Addresses are allocated after a negotiation between the server and the host to determine the length of the agreement.
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 112
Cisco 200-120 Exam
Which rule does the DHCP server use when there is an IP address conflict?
A. The address is removed from the pool until the conflict is resolved.
B. The address remains in the pool until the conflict is resolved.
C. Only the IP detected by Gratuitous ARP is removed from the pool.
D. Only the IP detected by Ping is removed from the pool.
E. The IP will be shown, even after the conflict is resolved.
Correct Answer: A
Section: (none)
Explanation
Explanation:
QUESTION 113

Cisco 200-120 Exam
What statement is true of the configuration for this network?
A. The configuration that is shown provides inadequate outside address space for translation of the number of inside addresses that are supported.
B. Because of the addressing on interface FastEthernet0/1, the Serial0/0 interface address will not support the NAT configuration as shown.
C. The number 1 referred to in the ip nat inside source command references access-list number 1.
D. ExternalRouter must be configured with static routes to networks 172.16.1.0/24 and 172.16.2.0/24.
Correct Answer: C
Section: (none)
Explanation
Explanation: The "list 1 refers to the access-list number 1.
QUESTION 114
Which two tasks does the Dynamic Host Configuration Protocol perform? (Choose two.)
A. Set the IP gateway to be used by the network.
B. Perform host discovery used DHCPDISCOVER message.
C. Configure IP address parameters from DHCP server to a host.
D. Provide an easy management of layer 3 devices.
E. Monitor IP performance using the DHCP server.
F. Assign and renew IP address from the default pool.
Correct Answer: CF
Section: (none)
Explanation
Explanation:
QUESTION 115
When a DHCP server is configured, which two IP addresses should never be assignable to hosts? (Choose two.)
A. network or subnetwork IP address
B. broadcast address on the network
C. IP address leased to the LAN
D. IP address used by the interfaces
E. manually assigned address to the clients
F. designated IP address to the DHCP server
Cisco 200-120 Exam
Correct Answer: AB
Section: (none)
Explanation
Explanation:
QUESTION 116
Which two statements about static NAT translations are true? (Choose two.)
A. They allow connections to be initiated from the outside.
B. They require no inside or outside interface markings because addresses are statically defined.
C. They are always present in the NAT table.
D. They can be configured with access lists, to allow two or more connections to be initiated from the outside.

Correct Answer: AC
Section: (none)
Explanation
Explanation:
QUESTION 117
Which statement about access lists that are applied to an interface is true?
A. You can place as many access lists as you want on any interface.
B. You can apply only one access list on any interface.
C. You can configure one access list, per direction, per Layer 3 protocol.
D. You can apply multiple access lists with the same protocol or in different directions.
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 118
Which item represents the standard IP ACL?
A. access-list 110 permit ip any any
B. access-list 50 deny 192.168.1.1 0.0.0.255
C. access list 101 deny tcp any host 192.168.1.1
D. access-list 2500 deny tcp any host 192.168.1.1 eq 22
Correct Answer: B
Section: (none)
Explanation
Cisco 200-120 Exam
Explanation:
QUESTION 119
A network administrator is configuring ACLs on a Cisco router, to allow traffic from hosts on networks 192.168.146.0, 192.168.147.0, 192.168.148.0, and
192.168.149.0 only. Which two ACL statements, when combined, would you use to accomplish this task? (Choose two.)
A. access-list 10 permit ip 192.168.146.0 0.0.1.255
B. access-list 10 permit ip 192.168.147.0 0.0.255.255
C. access-list 10 permit ip 192.168.148.0 0.0.1.255
D. access-list 10 permit ip 192.168.149.0 0.0.255.255
E. access-list 10 permit ip 192.168.146.0 0.0.0.255
F. access-list 10 permit ip 192.168.146.0 255.255.255.0
Correct Answer: AC
Section: (none)
Explanation
Explanation:
QUESTION 120
What can be done to secure the virtual terminal interfaces on a router? (Choose two.)
A. Administratively shut down the interface.
B. Physically secure the interface.
C. Create an access list and apply it to the virtual terminal interfaces with the access-group command.
D. Configure a virtual terminal password and login process.
E. Enter an access list and apply it to the virtual terminal interfaces using the access-class command.
Correct Answer: DE
Section: (none)
Explanation
Explanation:
QUESTION 121
Which two commands correctly verify whether port security has been configured on port FastEthernet 0/12 on a switch? (Choose two.)
Cisco 200-120 Exam
A. SW1#show port-secure interface FastEthernet 0/12
B. SW1#show switchport port-secure interface FastEthernet 0/12
C. SW1#show running-config
D. SW1#show port-security interface FastEthernet 0/12
E. SW1#show switchport port-security interface FastEthernet 0/12
Correct Answer: CD

Section: (none)
Explanation
Explanation:
QUESTION 122
The following commands are executed on interface fa0/1 of 2950Switch.
2950Switch(config-if)# switchport port-security
2950Switch(config-if)# switchport port-security mac-address sticky
2950Switch(config-if)# switchport port-security maximum 1
The Ethernet frame that is shown arrives on interface fa0/1. What two functions will occur when this frame is received by 2950Switch? (Choose two.)
A. The MAC address table will now have an additional entry of fa0/1 FFFF.FFFF.FFFF.
Cisco 200-120 Exam
B. Only host A will be allowed to transmit frames on fa0/1.
C. This frame will be discarded when it is received by 2950Switch.
D. All frames arriving on 2950Switch with a destination of 0000.00aa.aaaa will be forwarded out fa0/1.
E. Hosts B and C may forward frames out fa0/1 but frames arriving from other switches will not be forwarded out fa0/1.
F. Only frames from source 0000.00bb.bbbb, the first learned MAC address of 2950Switch, will be forwarded out fa0/1.
Correct Answer: BD
Section: (none)
Explanation
Explanation:
QUESTION 123
What will be the result if the following configuration commands are implemented on a Cisco switch?
Switch(config-if)# switchport port-security
Switch(config-if)# switchport port-security mac-address sticky
A. A dynamically learned MAC address is saved in the startup-configuration file.
B. A dynamically learned MAC address is saved in the running-configuration file.
C. A dynamically learned MAC address is saved in the VLAN database.
D. Statically configured MAC addresses are saved in the startup-configuration file if frames from that address are received.
E. Statically configured MAC addresses are saved in the running-configuration file if frames from that address are received.
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 124
The network administrator cannot connect to Switch1 over a Telnet session, although the hosts attached to Switch1 can ping the interface Fa0/0 of the router.
Given the information in the graphic and assuming that the router and Switch2 are configured properly, which of the following commands should be issued on
Switch1 to correct this problem?
A. Switch1(config)# line con0
Cisco 200-120 Exam
Switch1(config-line)# password cisco
Switch1(config-line)#login
B. Switch1(config)# interface fa0/1
Switch1(config-if)# ip address 192.168.24.3 255.255.255.0
C. Switch1(config)# ip default-gateway 192.168.24.1
D. Switch1(config)# interface fa0/1

Switch1(config-if)# duplex full
Switch1(config-if)# speed 100
E. Switch1(config)# interface fa0/1
Switch1(config-if)# switchport mode trunk
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 125
Which of these statements correctly describes the state of the switch once the boot process has been completed?
A. As FastEthernet0/12 will be the last to come up, it will be blocked by STP.
B. Remote access management of this switch will not be possible without configuration change.
C. More VLANs will need to be created for this switch.
D. The switch will need a different IOS code in order to support VLANs and STP.
Correct Answer: B
Section: (none)
Explanation
Explanation:
Cisco 200-120 Exam
QUESTION 126
Refer to exhibit.
Cisco 200-120 Exam

A network administrator cannot establish a Telnet session with the indicated router. What is the cause of this failure?
A. A Level 5 password is not set.
B. An ACL is blocking Telnet access.
C. The vty password is missing.
D. The console password is missing.
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 127
A router has two Fast Ethernet interfaces and needs to connect to four VLANs in the local
Cisco 200-120 Exam
network. How can you accomplish this task, using the fewest physical interfaces and without decreasing network performance?
A. Use a hub to connect the four VLANS with a Fast Ethernet interface on the router.
B. Add a second router to handle the VLAN traffic.
C. Add two more Fast Ethernet interfaces.
D. Implement a router-on-a-stick configuration.
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 128
A network administrator is trying to add a new router into an established OSPF network. The networks attached to the new router do not appear in the routing
tables of the other OSPF routers. Given the information in the partial configuration shown below, what configuration error is causing this problem?
Router(config)# router ospf 1
Router(config-router)# network 10.0.0.0 255.0.0.0 area 0
A. The process id is configured improperly.
B. The OSPF area is configured improperly.
C. The network wildcard mask is configured improperly.
D. The network number is configured improperly.
E. The AS is configured improperly.
F. The network subnet mask is configured improperly.
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 129
Which Cisco Catalyst feature automatically disables the port in an operational PortFast upon receipt of a BPDU?
A. BackboneFast
B. UplinkFast
C. Root Guard
D. BPDU Guard
E. BPDU Filter
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 130
Host 1 is trying to communicate with Host 2. The e0 interface on Router C is down.
Which of the following are true? (Choose two.)

A. Router C will use ICMP to inform Host 1 that Host 2 cannot be reached.
B. Router C will use ICMP to inform Router B that Host 2 cannot be reached.
C. Router C will use ICMP to inform Host 1, Router A, and Router B that Host 2 cannot be reached.
D. Router C will send a Destination Unreachable message type.
E. Router C will send a Router Selection message type.
F. Router C will send a Source Quench message type.
Correct Answer: AD
Section: (none)
Explanation
Explanation:
QUESTION 131
Cisco 200-120 Exam
When running EIGRP, what is required for RouterA to exchange routing updates with RouterC?
A. AS numbers must be changed to match on all the routers
B. Loopback interfaces must be configured so a DR is elected
C. The no auto-summary command is needed on Router A and Router C
D. Router B needs to have two network statements, one for each connected network
Correct Answer: A
Section: (none)
Explanation
Explanation:
QUESTION 132
A network technician is asked to design a small network with redundancy. The exhibit represents this design, with all hosts configured in the same VLAN. What
conclusions can be made about this design?
A. This design will function as intended.
B. Spanning-tree will need to be used.
C. The router will not accept the addressing scheme.
D. The connection between switches should be a trunk.
E. The router interfaces must be encapsulated with the 802.1Q protocol.
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 133

Cisco 200-120 Exam
The Bigtime router is unable to authenticate to the Littletime router. What is the cause of the problem?
A. The usernames are incorrectly configured on the two routers.
B. The passwords do not match on the two routers.
C. CHAP authentication cannot be used on a serial interface.
D. The routers cannot be connected from interface S0/0 to interface S0/0.
E. With CHAP authentication, one router must authenticate to another router. The routers cannot be configured to authenticate to each other.
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 134
Cisco 200-120 Exam
Given this output for SwitchC, what should the network administrator's next action be?
A. Check the trunk encapsulation mode for SwitchC's fa0/1 port.
B. Check the duplex mode for SwitchC's fa0/1 port.
C. Check the duplex mode for SwitchA's fa0/2 port.
D. Check the trunk encapsulation mode for SwitchA's fa0/2 port.
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 135
What will happen if a private IP address is assigned to a public interface connected to an ISP?
A. Addresses in a private range will be not be routed on the Internet backbone.
B. Only the ISP router will have the capability to access the public network.
C. The NAT process will be used to translate this address to a valid IP address.
D. A conflict of IP addresses happens, because other public routers can use the same range.
Correct Answer: A
Section: (none)

Explanation
Explanation:
Cisco 200-120 Exam
QUESTION 136
Which router IOS commands can be used to troubleshoot LAN connectivity problems? (Choose three.)
A. ping
B. tracert
C. ipconfig
Cisco 200-120 Exam
D. show ip route
E. winipcfg
F. show interfaces
Correct Answer: ADF
Section: (none)
Explanation
Explanation:
QUESTION 137
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common
Ethernet link.
The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this
problem?
A. The OSPF area is not configured properly.
B. The priority on R1 should be set higher.
C. The cost on R1 should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 138
In which circumstance are multiple copies of the same unicast frame likely to be transmitted in a
Cisco 200-120 Exam
switched LAN?
A. during high traffic periods
B. after broken links are re-established
C. when upper-layer protocols require high reliability
D. in an improperly implemented redundant topology
E. when a dual ring topology is in use
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 139
VLAN 3 is not yet configured on your switch. What happens if you set the switchport access vlan 3 command in interface configuration mode?
A. The command is rejected.

B. The port turns amber.
C. The command is accepted and the respective VLAN is added to vlan.dat.
D. The command is accepted and you must configure the VLAN manually.
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 140
Refer to the graphic.
R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)
A. All of the routers need to be configured for backbone Area 1.
B. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
C. A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
D. The hello and dead interval timers are not set to the same values on R1 and R3.
E. EIGRP is also configured on these routers with a lower administrative distance.
F. R1 and R3 are configured in different areas.
Correct Answer: DF
Section: (none)
Explanation
Explanation:
QUESTION 141
Cisco 200-120 Exam
The network shown in the diagram is experiencing connectivity problems. Which of the following will correct the problems? (Choose two.)
A. Configure the gateway on Host A as 10.1.1.1.
B. Configure the gateway on Host B as 10.1.2.254.
C. Configure the IP address of Host A as 10.1.2.2.
D. Configure the IP address of Host B as 10.1.2.2.
E. Configure the masks on both hosts to be 255.255.255.224.
F. Configure the masks on both hosts to be 255.255.255.240.
Correct Answer: BD
Section: (none)
Explanation
Explanation:
QUESTION 142

A problem with network connectivity has been observed. It is suspected that the cable connected
Cisco 200-120 Exam
to switch port Fa0/9 on Switch1 is disconnected. What would be an effect of this cable being disconnected?
A. Host B would not be able to access the server in VLAN9 until the cable is reconnected.
B. Communication between VLAN3 and the other VLANs would be disabled.
C. The transfer of files from Host B to the server in VLAN9 would be significantly slower.
D. For less than a minute, Host B would not be able to access the server in VLAN9. Then normal network function would resume.
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 143
HostA cannot ping HostB. Assuming routing is properly configured, what is the cause of this problem?
A. HostA is not on the same subnet as its default gateway.
B. The address of SwitchA is a subnet address.
C. The Fa0/0 interface on RouterA is on a subnet that can't be used.
D. The serial interfaces of the routers are not on the same subnet.
E. The Fa0/0 interface on RouterB is using a broadcast address.
Cisco 200-120 Exam
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 144

The two connected ports on the switch are not turning orange or green. What would be the most effective steps to troubleshoot this physical layer problem?
(Choose three.)
Cisco 200-120 Exam
A. Ensure that the Ethernet encapsulations match on the interconnected router and switch ports.
B. Ensure that cables A and B are straight-through cables.
C. Ensure cable A is plugged into a trunk port.
D. Ensure the switch has power.
E. Reboot all of the devices.
F. Reseat all cables.
Correct Answer: BDF
Section: (none)
Explanation
Explanation:
QUESTION 145
A network administrator attempts to ping Host2 from Host1 and receives the results that are shown. What is the problem?
A. The link between Host1 and Switch1 is down.
B. TCP/IP is not functioning on Host1
C. The link between Router1 and Router2 is down.
D. The default gateway on Host1 is incorrect.
E. Interface Fa0/0 on Router1 is shutdown.
F. The link between Switch1 and Router1 is down.
Correct Answer: C
Section: (none)
Explanation
Explanation:
Cisco 200-120 Exam
QUESTION 146

Hosts in network 192.168.2.0 are unable to reach hosts in network 192.168.3.0. Based on the output from RouterA, what are two possible reasons for the failure?
(Choose two.)
A. The cable that is connected to S0/0 on RouterA is faulty.
B. Interface S0/0 on RouterB is administratively down.
C. Interface S0/0 on RouterA is configured with an incorrect subnet mask.
D. The IP address that is configured on S0/0 of RouterB is not in the correct subnet.
E. Interface S0/0 on RouterA is not receiving a clock signal from the CSU/DSU.
F. The encapsulation that is configured on S0/0 of RouterB does not match the encapsulation that is configured on S0/0 of RouterA.
Correct Answer: EF
Section: (none)
Explanation
Explanation:
QUESTION 147
Cisco 200-120 Exam
An administrator pings the default gateway at 10.10.10.1 and sees the output as shown. At which OSI layer is the problem?
A. data link layer
B. application layer
C. access layer
D. session layer
E. network layer
Correct Answer: E
Section: (none)
Explanation
Explanation:
Topic 4, Volume D
QUESTION 148
"Pass Any Exam. Any Time." - www.actualtests.com 100 Cisco 200-120 Exam
Statements A, B, C, and D of ACL 10 have been entered in the shown order and applied to interface E0 inbound, to prevent all hosts (except those whose
addresses are the first and last IP of subnet 172.21.1.128/28) from accessing the network. But as is, the ACL does not restrict anyone from the network. How can
the ACL statements be re-arranged so that the system works as intended?
A. ACDB
B. BADC
C. DBAC
D. CDBA

Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 149
Which command is used to enable CHAP authentication, with PAP as the fallback method, on a serial interface?
A. Router(config-if)# ppp authentication chap fallback ppp
B. Router(config-if)# ppp authentication chap pap
C. Router(config-if)# authentication ppp chap fallback ppp
D. Router(config-if)# authentication ppp chap pap
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 150
Which protocol is an open standard protocol framework that is commonly used in VPNs, to provide secure end-to-end communications?
A. RSA
B. L2TP
C. IPsec
D. PPTP
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 151
The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router. Which of the following statements is true concerning this command?
A. This command should be executed from the global configuration mode.
B. The IP address 10.121.16.8 is the local router port used to forward data.
C. 102 is the remote DLCI that will receive the information.
D. This command is required for all Frame Relay configurations.
E. The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC.
Correct Answer: E
Section: (none)
Explanation
Explanation:
QUESTION 152
Which Layer 2 protocol encapsulation type supports synchronous and asynchronous circuits and has built-in security mechanisms?
A. HDLC
B. PPP
C. X.25
D. Frame Relay
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 153
Which encapsulation type is a Frame Relay encapsulation type that is supported by Cisco routers?
A. IETF
B. ANSI Annex D
C. Q9333-A Annex A
D. HDLC
Correct Answer: A
Section: (none)
Explanation
Explanation:
QUESTION 154
RouterA is unable to reach RouterB. Both routers are running IOS version 12.0.

After reviewing the command output and graphic, what is the most likely cause of the problem?
A. incorrect bandwidth configuration
B. incorrect LMI configuration
C. incorrect map statement
D. incorrect IP address
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 155
What is the meaning of the term dynamic as displayed in the output of the show frame-relay map command shown?
A. The Serial0/0 interface is passing traffic.
B. The DLCI 100 was dynamically allocated by the router.
C. The Serial0/0 interface acquired the IP address of 172.16.3.1 from a DHCP server.
D. The DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloud.
E. The mapping between DLCI 100 and the end station IP address 172.16.3.1 was learned through Inverse ARP.
Correct Answer: E
Section: (none)
Explanation
Explanation:
QUESTION 156
A network administrator needs to configure a serial link between the main office and a remote location. The router at the remote office is a non-Cisco router. How
should the network administrator configure the serial interface of the main office router to make the connection?
A. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# no shut
B. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# encapsulation ppp
Main(config-if)# no shut
C. Main(config)# interface serial 0/0
Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# encapsulation frame-relay
Main(config-if)# authentication chap
D. Main(config)# interface serial 0/0
Main(config-if)#ip address 172.16.1.1 255.255.255.252 "Pass Any Exam. Any Time." - www.actualtests.com 105 Cisco 200-120 Exam
Main(config-if)#encapsulation ietf
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 157
Which two statistics appear in show frame-relay map output? (Choose two.)
A. the number of BECN packets that are received by the router
B. the value of the local DLCI
C. the number of FECN packets that are received by the router
D. the status of the PVC that is configured on the router
E. the IP address of the local router
Correct Answer: BD
Section: (none)
Explanation

Explanation:
QUESTION 158
Users have been complaining that their Frame Relay connection to the corporate site is very slow. The network administrator suspects that the link is overloaded.
Based on the partial output of the Router# show frame relay pvc command shown in the graphic, which output value indicates to the local router that traffic sent to
the corporate site is experiencing congestion?
A. DLCI = 100
B. last time PVC status changed 00:25:40
C. in BECN packets 192
D. in FECN packets 147
E. in DE packets 0
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 159
It has become necessary to configure an existing serial interface to accept a second Frame Relay virtual circuit. Which of the following procedures are required to
accomplish this task? (Choose three.)
A. Remove the IP address from the physical interface.
B. Encapsulate the physical interface with multipoint PPP.
C. Create the virtual interfaces with the interface command.
D. Configure each subinterface with its own IP address.
E. Disable split horizon to prevent routing loops between the subinterface networks.
F. Configure static Frame Relay map entries for each subinterface network.
Correct Answer: ACD
Section: (none)
Explanation
Explanation:
QUESTION 160
What occurs on a Frame Relay network when the CIR is exceeded?
A. All TCP traffic is marked discard eligible.
B. All UDP traffic is marked discard eligible and a BECN is sent.
C. All TCP traffic is marked discard eligible and a BECN is sent.
D. All traffic exceeding the CIR is marked discard eligible.
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 161

Which statement describes DLCI 17?
A. DLCI 17 describes the ISDN circuit between R2 and R3.
B. DLCI 17 describes a PVC on R2. It cannot be used on R3 or R1.
C. DLCI 17 is the Layer 2 address used by R2 to describe a PVC to R3.
D. DLCI 17 describes the dial-up circuit from R2 and R3 to the service provider.
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 162
What is the result of issuing the frame-relay map ip 192.168.1.2 202 broadcast command?
A. defines the destination IP address that is used in all broadcast packets on DCLI 202
B. defines the source IP address that is used in all broadcast packets on DCLI 202 "Pass Any Exam. Any Time." - www.actualtests.com 109 Cisco 200-120 Exam
C. defines the DLCI on which packets from the 192.168.1.2 IP address are received
D. defines the DLCI that is used for all packets that are sent to the 192.168.1.2 IP address
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 163
What are two characteristics of Frame Relay point-to-point subinterfaces? (Choose two.)
A. They create split-horizon issues.
B. They require a unique subnet within a routing domain.
C. They emulate leased lines.
D. They are ideal for full-mesh topologies.
E. They require the use of NBMA options when using OSPF.
Correct Answer: BC
Section: (none)
Explanation
Explanation:
QUESTION 164
What command is used to verify the DLCI destination address in a Frame Relay static configuration?
A. show frame-relay pvc
B. show frame-relay lmi
C. show frame-relay map
D. show frame relay end-to-end
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 165
Two routers named Atlanta and Brevard are connected via their serial interfaces as illustrated, but they are unable to communicate. The Atlanta router is known to
have the correct configuration.

Given the partial configurations, identify the fault on the Brevard router that is causing the lack of
connectivity.
A. incompatible IP address
B. insufficient bandwidth
C. incorrect subnet mask
D. incompatible encapsulation
E. link reliability too low
F. IPCP closed
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 166
The company uses EIGRP as the routing protocol. What path will packets take from a host on the 192.168.10.192/26 network to a host on the LAN attached to
router R1?
A. The path of the packets will be R3 to R2 to R1.
B. The path of the packets will be R3 to R1 to R2.
C. The path of the packets will be both R3 to R2 to R1 AND R3 to R1.
D. The path of the packets will be R3 to R1.
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 167
How does using the service password-encryption command on a router provide additional security?
A. by encrypting all passwords passing through the router
B. by encrypting passwords in the plain text configuration file
C. by requiring entry of encrypted passwords for access to the device
D. by configuring an MD5 encrypted key to be used by routing protocols to validate routing exchanges

E. by automatically suggesting encrypted passwords for use in configuring the router
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 168
Switch port FastEthernet 0/24 on ALSwitch1 will be used to create an IEEE 802.1Q-compliant trunk to another switch. Based on the output shown, what is the
reason the trunk does not form, even though the proper cabling has been attached?
A. VLANs have not been created yet.
B. An IP address must be configured for the port.
C. The port is currently configured for access mode.
D. The correct encapsulation type has not been configured.
E. The no shutdown command has not been entered for the port.
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 169
In the Frame Relay network, which IP addresses would be assigned to the interfaces with point-to- point PVCs?
A. DLCI 16: 192.168.10.1 /24
DLCI 17: 192.168.10.1 /24
DLCI 99: 192.168.10.2 /24
DLCI 28: 192.168.10.3 /24
B. DLCI 16: 192.168.10.1 /24
DLCI 17: 192.168.11.1 /24
DLCI 99: 192.168.12.1 /24
DLCI 28: 192.168.13.1 /24
C. DLCI 16: 192.168.10.1 /24

DLCI 17: 192.168.11.1 /24
DLCI 99: 192.168.10.2 /24
DLCI 28: 192.168.11.2 /24
D. DLCI 16: 192.168.10.1 /24
DLCI 17: 192.168.10.2 /24
DLCI 99: 192.168.10.3 /24
DLCI 28: 192.168.10.4 /24
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 170
A new subnet with 60 hosts has been added to the network. Which subnet address should this network use to provide enough usable addresses while wasting the
fewest addresses?
A. 192.168.1.56/26
B. 192.168.1.56/27
C. 192.168.1.64/26
D. 192.168.1.64/27
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 171
All of the routers in the network are configured with the ip subnet-zero command. Which network
addresses should be used for Link A and Network A? (Choose two.)
A. Network A - 172.16.3.48/26
B. Network A - 172.16.3.128/25
C. Network A - 172.16.3.192/26
D. Link A - 172.16.3.0/30
E. Link A - 172.16.3.40/30
F. Link A - 172.16.3.112/30
Correct Answer: BD
Section: (none)
Explanation
Explanation:
QUESTION 172
A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560.
Another route is from OSPF with a metric of 782. The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table?
A. the OSPF route
B. the EIGRP route

C. the RIPv2 route
D. all three routes
E. the OSPF and RIPv2 routes
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 173
A network administrator needs to allow only one Telnet connection to a router. For anyone viewing the configuration and issuing the show run command, the
password for Telnet access should be encrypted. Which set of commands will accomplish this task?
A. service password-encryption
access-list 1 permit 192.168.1.0 0.0.0.255
line vty 0 4
login
password cisco
access-class 1
B. enable password secret
line vty 0
login
password cisco
C. service password-encryption
line vty 1
login
password cisco
D. service password-encryption
line vty 0 4
login
password cisco
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 174
The speed of all serial links is E1 and the speed of all Ethernet links is 100 Mb/s. A static route will be established on the Manchester router to direct traffic toward
the Internet over the most direct path available. What configuration on the Manchester router will establish a route toward the Internet for traffic that originates from
workstations on the Manchester LAN?
A. ip route 0.0.0.0 255.255.255.0 172.16.100.2
B. ip route 0.0.0.0 0.0.0.0 128.107.1.1
C. ip route 0.0.0.0 255.255.255.252 128.107.1.1
D. ip route 0.0.0.0 0.0.0.0 172.16.100.1
E. ip route 0.0.0.0 0.0.0.0 172.16.100.2
F. ip route 0.0.0.0 255.255.255.255 172.16.100.2
Correct Answer: E
Section: (none)
Explanation
Explanation:
QUESTION 175

The network administrator must establish a route by which London workstations can forward traffic to the Manchester workstations. What is the simplest way to
accomplish this?
A. Configure a dynamic routing protocol on London to advertise all routes to Manchester.
B. Configure a dynamic routing protocol on London to advertise summarized routes to Manchester.
C. Configure a dynamic routing protocol on Manchester to advertise a default route to the London router.
D. Configure a static default route on London with a next hop of 10.1.1.1.
E. Configure a static route on London to direct all traffic destined for 172.16.0.0/22 to 10.1.1.2.
F. Configure Manchester to advertise a static default route to London.
Correct Answer: E
Section: (none)
Explanation
Explanation:
QUESTION 176
The network administrator requires easy configuration options and minimal routing protocol traffic. What two options provide adequate routing table information for
traffic that passes between the two routers and satisfy the requests of the network administrator? (Choose two.)
A. a dynamic routing protocol on InternetRouter to advertise all routes to CentralRouter.
B. a dynamic routing protocol on InternetRouter to advertise summarized routes to CentralRouter.
C. a static route on InternetRouter to direct traffic that is destined for 172.16.0.0/16 to CentralRouter.
D. a dynamic routing protocol on CentralRouter to advertise all routes to InternetRouter.
E. a dynamic routing protocol on CentralRouter to advertise summarized routes to InternetRouter.
F. a static, default route on CentralRouter that directs traffic to InternetRouter.
Correct Answer: CF
Section: (none)

Explanation
Explanation:
QUESTION 177
What is the effect of using the service password-encryption command?
A. Only the enable password will be encrypted.
B. Only the enable secret password will be encrypted.
C. Only passwords configured after the command has been entered will be encrypted.
D. It will encrypt the secret password and remove the enable secret password from the configuration.
E. It will encrypt all current and future passwords.
Correct Answer: E
Section: (none)
Explanation
Explanation:
QUESTION 178
What is the effect of the configuration that is shown?
A. It configures SSH globally for all logins.
B. It tells the router or switch to try to establish an SSh connection first and if that fails to use Telnet.
C. It configures the virtual terminal lines with the password 030752180500.
D. It configures a Cisco network device to use the SSH protocol on incoming communications via the virtual terminal ports.
E. It allows seven failed login attempts before the VTY lines are temporarily shutdown.
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 179
What is the reason that the interface status is "administratively down, line protocol down"?
A. There is no encapsulation type configured.
B. There is a mismatch in encapsulation types.
C. The interface is not receiving any keepalives.
D. The interface has been configured with the shutdown command.
E. The interface needs to be configured as a DTE device.
F. The wrong type of cable is connected to the interface.
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 180

When running OSPF, what would cause router A not to form an adjacency with router B?
A. The loopback addresses are on different subnets.
B. The values of the dead timers on the routers are different.
C. Route summarization is enabled on both routers.
D. The process identifier on router A is different than the process identifier on router B.
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 181
Which two of these statements are true of IPv6 address representation? (Choose two.)
A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
B. A single interface may be assigned multiple IPv6 addresses of any type.
C. Every IPv6 interface contains at least one loopback address.
D. The first 64 bits represent the dynamically created interface ID.
E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.
Correct Answer: BC
Section: (none)
Explanation
Explanation:
QUESTION 182
A junior network administrator was given the task of configuring port security on SwitchA to allow only PC_A to access the switched network through port fa0/1. If
any other device is detected, the
port is to drop frames from this device. The administrator configured the interface and tested it with successful pings from PC_A to RouterA, and then observes the
output from these two show commands.
Which two of these changes are necessary for SwitchA to meet the requirements? (Choose two.)
A. Port security needs to be globally enabled.
B. Port security needs to be enabled on the interface.
C. Port security needs to be configured to shut down the interface in the event of a violation.

D. Port security needs to be configured to allow only one learned MAC address.
E. Port security interface counters need to be cleared before using the show command.
F. The port security configuration needs to be saved to NVRAM before it can become active.
Correct Answer: BD
Section: (none)
Explanation
Explanation:
QUESTION 183
Which set of commands is recommended to prevent the use of a hub in the access layer?
A. switch(config-if)#switchport mode trunk
switch(config-if)#switchport port-security maximum 1
B. switch(config-if)#switchport mode trunk
switch(config-if)#switchport port-security mac-address 1
C. switch(config-if)#switchport mode access
switch(config-if)#switchport port-security maximum 1
D. switch(config-if)#switchport mode access
switch(config-if)#switchport port-security mac-address 1
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 184
What is known as "one-to-nearest" addressing in IPv6?
A. global unicast
B. anycast
C. multicast
D. unspecified address
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 185
What is the first 24 bits in a MAC address called?
A. NIC
B. BIA
C. OUI
D. VAI
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 186
Which subnet mask will place all hosts on Network B in the same subnet with the least amount of wasted addresses?
A. 255.255.255.0
B. 255.255.254.0
C. 255.255.252.0
D. 255.255.248.0
Correct Answer: B
Section: (none)
Explanation
Explanation:

QUESTION 187
What is the most appropriate summarization for these routes?
A. 10.0.0.0 /21
B. 10.0.0.0 /22
C. 10.0.0.0 /23
D. 10.0.0.0 /24
Correct Answer: B
Section: (none)
Explanation
Explanation:
QUESTION 188
What is the difference between a CSU/DSU and a modem?
A. A CSU/DSU converts analog signals from a router to a leased line; a modem converts analog signals from a router to a leased line.
B. A CSU/DSU converts analog signals from a router to a phone line; a modem converts digital signals from a router to a leased line.
C. A CSU/DSU converts digital signals from a router to a phone line; a modem converts analog signals from a router to a phone line.
D. A CSU/DSU converts digital signals from a router to a leased line; a modem converts digital signals from a router to a phone line.
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 189
Which two are features of IPv6? (Choose two.)
A. anycast
B. broadcast
C. multicast
D. podcast
E. allcast
Correct Answer: AC
Section: (none)
Explanation
Explanation:
QUESTION 190
Which two are advantages of static routing when compared to dynamic routing? (Choose two.)
A. Configuration complexity decreases as network size increases.
B. Security increases because only the network administrator may change the routing table.
C. Route summarization is computed automatically by the router.
D. Routing tables adapt automatically to topology changes.
E. An efficient algorithm is used to build routing tables, using automatic updates.
F. Routing updates are automatically sent to neighbors.
G. Routing traffic load is reduced when used in stub network links.
Correct Answer: BG
Section: (none)
Explanation
Explanation:
QUESTION 191
A network administrator needs to configure port security on a switch. Which two statements are true? (Choose two.)
A. The network administrator can apply port security to dynamic access ports.
B. The network administrator can apply port security to EtherChannels.
C. When dynamic MAC address learning is enabled on an interface, the switch can learn new addresses, up to the maximum defined.
D. The sticky learning feature allows the addition of dynamically learned addresses to the running configuration.
E. The network administrator can configure static secure or sticky secure MAC addresses in the voice VLAN.

Correct Answer: CD
Section: (none)
Explanation
Explanation:
QUESTION 192
What are three features of the IPv6 protocol? (Choose three.)
A. optional IPsec
B. autoconfiguration
C. no broadcasts
D. complicated header
E. plug-and-play
F. checksums
Correct Answer: BCE
Section: (none)
Explanation
Explanation:
QUESTION 193
Which command enables IPv6 forwarding on a Cisco router?
A. ipv6 local
B. ipv6 host
C. ipv6 unicast-routing
D. ipv6 neighbor
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 194
Which command encrypts all plaintext passwords?
A. Router# service password-encryption
B. Router(config)# password-encryption
C. Router(config)# service password-encryption
D. Router# password-encryption
Correct Answer: C
Section: (none)
Explanation
Explanation:
QUESTION 195
Given an IP address 172.16.28.252 with a subnet mask of 255.255.240.0, what is the correct network address?
A. 172.16.16.0
B. 172.16.0.0
C. 172.16.24.0
D. 172.16.28.0
Correct Answer: A
Section: (none)
Explanation
Explanation:
QUESTION 196
You are working in a data center environment and are assigned the address range 10.188.31.0/23. You are asked to develop an IP addressing plan to allow the
maximum number of subnets with as many as 30 hosts each. Which IP address range meets these requirements?
A. 10.188.31.0/26
B. 10.188.31.0/25
C. 10.188.31.0/28
D. 10.188.31.0/27
E. 10.188.31.0/29
Correct Answer: D
Section: (none)
Explanation
Explanation:
QUESTION 197

Which parameter or parameters are used to calculate OSPF cost in Cisco routers?
A. Bandwidth
B. Bandwidth and Delay
C. Bandwidth, Delay, and MTU
D. Bandwidth, MTU, Reliability, Delay, and Load
Correct Answer: A
Section: (none)
Explanation
Explanation:
QUESTION 198
DRAG DROP
A.
B.
C.
D.
Correct Answer:
Section: (none)
Explanation
Explanation:
QUESTION 199
DRAG DROP

A.
B.
C.
D.
Correct Answer:
Section: (none)
Explanation
Explanation:
Explanation
If we have many entries matching for next hop ip address then the router will choose the one with most specific path to send the packet. This is called the "longest
match" rule, the route with the most bits in the mask set to "1 will be chosen to route packet.
QUESTION 200
DRAG DROP

A.
B.
C.
D.
Correct Answer:
Section: (none)
Explanation
Explanation:
A simple way to find out which layer is having problem is to remember this rule: "the first statement is for Layer 1, the last statement is for Layer 2 and if Layer 1 is
down then surely Layer 2 will be down too", so you have to check Layer 1 before checking Layer 2. For example, from the output "Serial0/1 is up, line protocol is
down" we know that it is a layer 2 problem because the first statement (Serial0/1 is up) is good while the last statement (line protocol is down) is bad. For the
statement "Serial0/1 is down, line protocol is down", both layers are down so the problem belongs to Layer 1.
There is only one special case with the statement ".... is administrator down, line protocol is down". In this case, we know that the port is currently disabled and
shut down by the administrators.
QUESTION 201
DRAG DROP

A.
B.
C.
D.
Correct Answer:
Section: (none)
Explanation
Explanation:
QUESTION 202
DRAG DROP
A.
B.
C.
D.
Correct Answer:
Section: (none)
Explanation
Explanation:

The question asks us to "begin with the lowest layer" so we have to begin with Layer 1: verify physical connection; in this case an Ethernet cable connection. For
your information, "verify Ethernet cable connection" means that we check if the type of connection (crossover, straight- through, rollover...) is correct, the RJ45
headers are plugged in, the signal on the cable is acceptable...
Next we "verify NIC operation". We do this by simply making a ping to the loopback interface 127.0.0.1. If it works then the NIC card (layer 1, 2) and TCP/IP stack
(layer 3) are working properly.
Verify IP configuration belongs to layer 3. For example, checking if the IP can be assignable for host, the PC's IP is in the same network with the gateway...
Verifying the URL by typing in your browser some popular websites like google.com, microsoft.com to assure that the far end server is not down (it sometimes
make we think we can't access to the Internet). We are using a URL so this step belongs to layer 7 of the OSI model.
QUESTION 203
CORRECT TEXT
A network associate is adding security to the configuration of the Corp1 router. The user on host C should be able to use a web browser to access financial
information from the Finance Web Server. No other hosts from the LAN nor the Core should be able to use a web browser to access this server. Since there are
multiple resources for the corporation at this location including other resources on the Finance Web Server, all other traffic should be allowed.
The task is to create and apply an access-list with no more than three statements that will allow ONLY host C web access to the Finance Web Server. No other
hosts will have web access to the Finance Web Server. All other traffic is permitted.
Access to the router CLI can be gained by clicking on the appropriate host.
All passwords have been temporarily set to "cisco".
The Core connection uses an IP address of 198.18.196.65
The computers in the Hosts LAN have been assigned addresses of 192.168.33.1 - 192.168.33.254
Host A 192.168.33.1
Host B 192.168.33.2
Host C 192.168.33.3
Host D 192.168.33.4
The servers in the Server LAN have been assigned addresses of 172.22.242.17 - 172.22.242.30
The Finance Web Server is assigned an IP address of 172.22.242.23.

A.
B.
C.
D.
Correct Answer:
Section: (none)
Explanation
Answer: Select the console on Corp1 router
Configuring ACL
Corp1>enable
Corp1#configure terminal
comment: To permit only Host C (192.168.33.3){source addr} to access finance server address (172.22.242.23) {destination addr} on port number 80 (web) Corp1
(config)#access-list 100 permit tcp host 192.168.33.3 host 172.22.242.23 eq 80 comment: To deny any source to access finance server address (172.22.242.23)
{destination addr} on port number 80 (web)
Corp1(config)#access-list 100 deny tcp any host 172.22.242.23 eq 80 comment: To permit ip protocol from any source to access any destination because of the
implicit deny any any statement at the end of ACL.
Corp1(config)#access-list 100 permit ip any any
Applying the ACL on the Interface
comment: Check show ip interface brief command to identify the interface type and number by checking the IP address configured.
Corp1(config)#interface fa 0/1
If the ip address configured already is incorrect as well as the subnet mask. this should be corrected in order ACL to work
type this commands at interface mode :
no ip address 192.x.x.x 255.x.x.x (removes incorrect configured ipaddress and subnet mask) Configure Correct IP Address and subnet mask :
ip address 172.22.242.30 255.255.255.240 ( range of address specified going to server is given as 172.22.242.17 - 172.22.242.30 )
comment: Place the ACL to check for packets going outside the interface towards the finance web server.
Corp1(config-if)#ip access-group 100 out
Corp1(config-if)#end
Important: To save your running config to startup before exit.
Corp1#copy running-config startup-config
Verifying the Configuration :
Step1: show ip interface brief command identifies the interface on which to apply access list. Step2: Click on each host A,B,C & D . Host opens a web browser
page , Select address box of the web browser and type the ip address of finance web server(172.22.242.23) to test whether it permits /deny access to the finance
web Server .
Step 3: Only Host C (192.168.33.3) has access to the server . If the other host can also access then maybe something went wrong in your configuration . check
whether you configured correctly and in order.
Step 4: If only Host C (192.168.33.3) can access the Finance Web Server you can click on NEXT button to successfully submit the ACL SIM.
QUESTION 204
DRAG DROP

A.
B.
C.
D.
Correct Answer:
Section: (none)
Explanation
Explanation:
Source Mac Address Destination Mac Address Source IP address Destination MAC address MAC 0000.0c89.3333 MAC 0000.0c89.9999 IP 172.16.34.250 IP
172.16.21.7
QUESTION 205
DRAG DROP
A.
B.

C.
D.
Correct Answer:
Section: (none)
Explanation
Explanation:
QUESTION 206

What would be the effect of issuing the command ip access-group 114 in to the fa0/0 interface?
A. Attempts to telnet to the router would fail.
B. It would allow all traffic from the 10.4.4.0 network.
C. IP traffic would be passed through the interface but TCP and UDP traffic would not.
D. Routing protocol updates for the 10.4.4.0 network would not be accepted from the fa0/0 interface.
Correct Answer: B
Section: (none)
Explanation
Explanation: From the output of access-list 114: access-list 114 permit ip 10.4.4.0 0.0.0.255 any we can easily understand that this access list allows all traffic (ip)
from 10.4.4.0/24 network
QUESTION 207
CORRECT TEXT

A.
B.
C.
D.
Correct Answer:
Section: (none)
Explanation
Answer: On the MGT Router:
Config t
Router eigrp 12
Network 192.168.77.0
QUESTION 208
CORRECT TEXT
Lab-NAT

A network associate is configuring a router for the weaver company to provide internet access. The ISP has provided the company six public IP addresses of
198.18.184.105 198.18.184.110. The company has 14 hosts that need to access the internet simultaneously. The hosts in the company LAN have been assigned
private space addresses in the range of 192.168.100.17 192.168.100.30.
A.
B.
C.
D.
Correct Answer:
Section: (none)
Explanation
Answer: The company has 14 hosts that need to access the internet simultaneously but we just have 6 public IP addresses from 198.18.184.105 to
198.18.184.110/29.
Therefore we have to use NAT overload (or PAT)
Double click on the Weaver router to open it
Router>enable
Router#configure terminal
First you should change the router's name to Weaver
Router(config)#hostname Weaver
Create a NAT pool of global addresses to be allocated with their netmask. Weaver(config)#ip nat pool mypool 198.18.184.105 198.18.184.110 netmask
255.255.255.248
Create a standard access control list that permits the addresses that are to be translated
Weaver(config)#access-list 1 permit 192.168.100.16 0.0.0.15 Establish dynamic source translation, specifying the access list that was defined in the prior step
Weaver(config)#ip nat inside source list 1 pool mypool overload This command translates all source addresses that pass access list 1, which means a source
address from 192.168.100.17 to 192.168.100.30, into an address from the pool named mypool (the pool contains addresses from 198.18.184.105 to
198.18.184.110)
Overload keyword allows to map multiple IP addresses to a single registered IP address (many-to-one) by using different ports
The question said that appropriate interfaces have been configured for NAT inside and NAT outside statements.
This is how to configure the NAT inside and NAT outside, just for your understanding:
Weaver(config)#interface fa0/0
Weaver(config-if)#ip nat inside
Weaver(config-if)#exit
Weaver(config)#interface s0/0
Weaver(config-if)#ip nat outside
Weaver(config-if)#end
Finally, we should save all your work with the following command:
Weaver#copy running-config startup-config
Check your configuration by going to "Host for testing" and type:

C :>ping 192.0.2.114
The ping should work well and you will be replied from 192.0.2.114
QUESTION 209
CORRECT TEXT
A.
B.
C.
D.
Correct Answer:
Section: (none)
Explanation
Answer: Select the console on Corp1 router
Configuring ACL
Corp1>enable
comment: To permit only Host C (192.168.33.3){source addr} to access finance server address (172.22.242.23) {destination addr} on port number 80 (web) Corp1
(config)#access-list 100 permit tcp host 192.168.33.3 host 172.22.242.23 eq 80 comment: To deny any source to access finance server address (172.22.242.23)
Corp1(config)#access-list 100 deny tcp any host 172.22.242.23 eq 80 comment: To permit ip protocol from any source to access any destination because of the
If the ip address configured already is incorrect as well as the subnet mask. this should be corrected in order ACL to work
no ip address 192.x.x.x 255.x.x.x (removes incorrect configured ipaddress and subnet mask) Configure Correct IP Address and subnet mask :
ip address 172.22.242.30 255.255.255.240 ( range of address specified going to server is given as 172.22.242.17 - 172.22.242.30 )
Important: To save your running config to startup before exit.
Verifying the Configuration :
Step1: show ip interface brief command identifies the interface on which to apply access list. Step2: Click on each host A,B,C & D . Host opens a web browser
page , Select address box of the web browser and type the ip address of finance web server(172.22.242.23) to test whether it permits /deny access to the finance
web Server .
Step 3: Only Host C (192.168.33.3) has access to the server . If the other host can also access then maybe something went wrong in your configuration . check
whether you configured correctly and in order.
Step 4: If only Host C (192.168.33.3) can access the Finance Web Server you can click on NEXT button to successfully submit the ACL SIM.

QUESTION 210
CORRECT TEXT
ACL-3
A.
B.
C.
D.
Correct Answer:
Section: (none)
Explanation
Answer: Corp1>enable
Corp1(config)#access-list 100 permit tcp host 192.168.33.3 host 172.22.242.23 eq 80 Corp1(config)#access-list 100 deny tcp 192.168.33.0 0.0.0.255 host
172.22.242.23 eq 80 Corp1(config)#access-list 100 permit ip any any
Corp1(config)#interface fa 0/1 sh ip int brief
Explanation:
Select the console on Corp1 router
Configuring ACL Corp1 >enable Corp1#configure terminal comment: To permit only Host C (192.168. 33. 3){source addr} to access finance server address (172.
22. 242. 23)
Corp1(config)#access-list 100 permit tcp host 192. 168. 33. 3 host 172. 22. 242. 23 eq 80 comment: To deny any source to access finance server address (172.
22. 242. 23) {destination addr} on port number 80 (web)
Corp1(config)#access-list 100 deny tcp any host 172. 22. 242. 23 eq 80 comment: To permit ip protocol from any source to access any destination because of the

If the ip address configured already is incorrect as well as the subnet mask, this should be corrected in order
ACL to work
no ip address 192. x. x. x 255. x. x. x (removes incorrect configured ip address and subnet mask) Configure Correct IP Address and subnet mask:
ip address 172. 22. 242. 30 255. 255. 255. 240 (range of address specified going to server is given as 172. 22. 242. 17-172. 22. 242. 30 )
Important: To save your running config to startup before exit. Corp1#copy running-config startup- config Verifying the Configuration :
Step1: show ip interface brief command identifies the interface on which to apply access list. Step2: Click on each host A,B,C & D. Host opens a web browser
page, Select address box of the web browser and type the ip address of finance web server(172. 22. 242. 23) to test whether it permits /deny access to the finance
web Server.
Step 3: Only Host C (192.168. 33. 3) has access to the server. If the other host can also access
then maybe something went wrong in your configuration check whether you configured correctly and in order.
Step 4: If only Host C (192.168. 33. 3) can access the Finance Web Server you can click on NEXT button to successfully submit the ACL SIM.

Cisco CCNAX .200 120

More Related Content

What's hot (19)

Viewers also liked (20)

Similar to Cisco CCNAX .200 120 (20)

More from abdulquyyum (6)

Recently uploaded (20)

Cisco CCNAX .200 120