Cisco Network and Engineering
Download as DOCX, PDF0 likes82 views
The document describes the configuration of several routers - Jakarta, Batam, Jawa, and Kalimantan. For each router, it configures interface IP addresses and enables the interfaces. It also configures static routes on each router to route traffic between the different networks.
![Jakarta(config-if)#exit
Jakarta(config)#int se 0/0
Jakarta(config-if)#ip address 193.42.55.1 255.255.255.0
Jakarta(config-if)#no shut
%LINK-5-CHANGED: Interface Serial0/0, changed state to down
Jakarta(config-if)#clock rate 64000
Jakarta(config-if)#exit
Jakarta(config)#int se 0/1
Jakarta(config-if)#ip address 172.16.0.2 255.255.0.0
Jakarta(config-if)#no shut
Jakarta(config-if)#
%LINK-5-CHANGED: Interface Serial0/1, changed state to up
Jakarta(config-if)#exit
Jakarta(config)#exit
Jakarta#
%SYS-5-CONFIG_I: Configured from console by console
Jakarta#copy running start
Destination filename [startup-config]?
Building configuration...
[OK]](https://image.slidesharecdn.com/isnadwisetianingsih-180429074800/85/Cisco-Network-and-Engineering-2-320.jpg)
![Konfigurasi Ip Route
Jakarta(config)#ip route 193.46.54.0 255.255.255.0 193.42.55.1
%Invalid next hop address (it's this router)
Jakarta(config)#ip route 193.46.54.0 255.255.255.0 193.42.55.2
Jakarta(config)#ip route 193.16.10.0 255.255.255.0 172.16.60.2
Jakarta(config)#ip route 10.0.0.0 255.0.0.0 172.16.0.1
Jakarta(config)#exit
Jakarta#
%SYS-5-CONFIG_I: Configured from console by console
Jakarta#copy running start
Destination filename [startup-config]?
Building configuration...
[OK]
Jakarta#](https://image.slidesharecdn.com/isnadwisetianingsih-180429074800/85/Cisco-Network-and-Engineering-3-320.jpg)
![Konfigurasi Router Batam
Router>enable
Router#conf term
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname Batam
Batam(config)#int fa 0/0
Batam(config-if)#ip address 193.46.54.1 255.255.255.0
Batam(config-if)#no shut
Batam(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to
up
Batam(config-if)#exit
Batam(config)#int se 0/0
Batam(config-if)#ip address 172.16.60.1 255.255.0.0
Batam(config-if)#no shut
%LINK-5-CHANGED: Interface Serial0/0, changed state to down
Batam(config-if)#clock rate 64000
Batam(config-if)#exit
Batam(config)#exit
Batam#
%SYS-5-CONFIG_I: Configured from console by console
Batam#copy running start
Destination filename [startup-config]?
Building configuration...
[OK]](https://image.slidesharecdn.com/isnadwisetianingsih-180429074800/85/Cisco-Network-and-Engineering-4-320.jpg)
![Konfigurasi Ip Route
Batam>enable
Batam#conf term
Enter configuration commands, one per line. End with CNTL/Z.
Batam(config)#ip route 193.34.24.0 255.255.255.0 193.42.55.1
Batam(config)#ip route 193.16.10.0 255.255.255.0 172.16.60.2
Batam(config)#ip route 10.0.0.0 255.0.0.0 193.18.4.2
Batam(config)#exit
Batam#copy running start
Destination filename [startup-config]?
Building configuration...
[OK]](https://image.slidesharecdn.com/isnadwisetianingsih-180429074800/85/Cisco-Network-and-Engineering-5-320.jpg)
![Jawa(config)#int se 0/0
Jawa(config-if)#ip address 193.18.4.1 255.255.255.0
Jawa(config-if)#no shut
%LINK-5-CHANGED: Interface Serial0/0, changed state to down
Jawa(config-if)#clock rate 64000
Jawa(config-if)#exit
Jawa(config)#exit
Jawa#
%SYS-5-CONFIG_I: Configured from console by console
Jawa#copy running start
Destination filename [startup-config]?
Building configuration...
[OK]
Jawa#](https://image.slidesharecdn.com/isnadwisetianingsih-180429074800/85/Cisco-Network-and-Engineering-8-320.jpg)
![Konfigurasi Ip Route
Jawa>enable
Jawa#conf term
Enter configuration commands, one per line. End with CNTL/Z.
Jawa(config)#ip route 193.34.24.0 255.255.255.0 193.42.55.1
Jawa(config)#ip route 193.46.54.0 255.255.255.0 172.16.60.1
Jawa(config)#ip route 10.0.0.0 255.0.0.0 193.18.4.2
Jawa(config)#exit
Jawa#
%SYS-5-CONFIG_I: Configured from console by console
Jawa#copy running start
Destination filename [startup-config]?
Building configuration...
[OK]
Jawa#](https://image.slidesharecdn.com/isnadwisetianingsih-180429074800/85/Cisco-Network-and-Engineering-9-320.jpg)
![Kalimantan (config-if)#
%LINK-5-CHANGED: Interface Serial0/1, changed state to up
Kalimantan (config-if)#exit
%LINK-5-CHANGED: Interface Serial0/0, changed state to down
Kalimantan (config-if)#clock rate 64000
Kalimantan (config-if)#exit
Kalimantan (config)#exit
Kalimantan #
%SYS-5-CONFIG_I: Configured from console by console
Kalimantan #copy running start
Destination filename [startup-config]?
Building configuration...
[OK]
Konfigurasi Ip Route
Kalimantan>enable
Kalimantan#conf term
Enter configuration commands, one per line. End with CNTL/Z.
Kalimantan(config)# ip route 193.34.24.0 255.255.255.0 172.16.0.2
Kalimantan(config)# ip route 193.46.54.0 255.255.255.0 172.16.60.1
Kalimantan(config)#ip route 193.16.10.0 255.255.255.0 193.18.4.1
Kalimantan(config)#exit
Kalimantan#
%SYS-5-CONFIG_I: Configured from console by console
Kalimantan#copy running start
Destination filename [startup-config]?
Building configuration...](https://image.slidesharecdn.com/isnadwisetianingsih-180429074800/85/Cisco-Network-and-Engineering-11-320.jpg)
![[OK]
Kalimantan#](https://image.slidesharecdn.com/isnadwisetianingsih-180429074800/85/Cisco-Network-and-Engineering-12-320.jpg)
Cisco Network and Engineering
- 1. Konfigurasi Router Jakarta Router>enable Router#conf term Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname Jakarta Jakarta(config)#int fa 0/0 Jakarta(config-if)#ip address 193.34.24.1 255.255.255.0 Jakarta(config-if)#no shut Jakarta(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
- 2. Jakarta(config-if)#exit Jakarta(config)#int se 0/0 Jakarta(config-if)#ip address 193.42.55.1 255.255.255.0 Jakarta(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/0, changed state to down Jakarta(config-if)#clock rate 64000 Jakarta(config-if)#exit Jakarta(config)#int se 0/1 Jakarta(config-if)#ip address 172.16.0.2 255.255.0.0 Jakarta(config-if)#no shut Jakarta(config-if)# %LINK-5-CHANGED: Interface Serial0/1, changed state to up Jakarta(config-if)#exit Jakarta(config)#exit Jakarta# %SYS-5-CONFIG_I: Configured from console by console Jakarta#copy running start Destination filename [startup-config]? Building configuration... [OK]
- 3. Konfigurasi Ip Route Jakarta(config)#ip route 193.46.54.0 255.255.255.0 193.42.55.1 %Invalid next hop address (it's this router) Jakarta(config)#ip route 193.46.54.0 255.255.255.0 193.42.55.2 Jakarta(config)#ip route 193.16.10.0 255.255.255.0 172.16.60.2 Jakarta(config)#ip route 10.0.0.0 255.0.0.0 172.16.0.1 Jakarta(config)#exit Jakarta# %SYS-5-CONFIG_I: Configured from console by console Jakarta#copy running start Destination filename [startup-config]? Building configuration... [OK] Jakarta#
- 4. Konfigurasi Router Batam Router>enable Router#conf term Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname Batam Batam(config)#int fa 0/0 Batam(config-if)#ip address 193.46.54.1 255.255.255.0 Batam(config-if)#no shut Batam(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up Batam(config-if)#exit Batam(config)#int se 0/0 Batam(config-if)#ip address 172.16.60.1 255.255.0.0 Batam(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/0, changed state to down Batam(config-if)#clock rate 64000 Batam(config-if)#exit Batam(config)#exit Batam# %SYS-5-CONFIG_I: Configured from console by console Batam#copy running start Destination filename [startup-config]? Building configuration... [OK]
- 5. Konfigurasi Ip Route Batam>enable Batam#conf term Enter configuration commands, one per line. End with CNTL/Z. Batam(config)#ip route 193.34.24.0 255.255.255.0 193.42.55.1 Batam(config)#ip route 193.16.10.0 255.255.255.0 172.16.60.2 Batam(config)#ip route 10.0.0.0 255.0.0.0 193.18.4.2 Batam(config)#exit Batam#copy running start Destination filename [startup-config]? Building configuration... [OK]
- 7. Konfigurasi Router Jawa Router#conf term Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname Jawa Jawa(config)#int fa 0/0 Jawa(config-if)#ip address 193.16.10.3 255.255.255.0 Jawa(config-if)#no shut Jawa(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up Jawa(config-if)#exit Jawa(config)#int se 0/1 Jawa(config-if)#ip address 172.16.60.2 255.255.0.0 Jawa(config-if)#no shut Jawa(config-if)# %LINK-5-CHANGED: Interface Serial0/1, changed state to up Jawa(config-if)#exit Jawa(config)#int %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to
- 8. Jawa(config)#int se 0/0 Jawa(config-if)#ip address 193.18.4.1 255.255.255.0 Jawa(config-if)#no shut %LINK-5-CHANGED: Interface Serial0/0, changed state to down Jawa(config-if)#clock rate 64000 Jawa(config-if)#exit Jawa(config)#exit Jawa# %SYS-5-CONFIG_I: Configured from console by console Jawa#copy running start Destination filename [startup-config]? Building configuration... [OK] Jawa#
- 9. Konfigurasi Ip Route Jawa>enable Jawa#conf term Enter configuration commands, one per line. End with CNTL/Z. Jawa(config)#ip route 193.34.24.0 255.255.255.0 193.42.55.1 Jawa(config)#ip route 193.46.54.0 255.255.255.0 172.16.60.1 Jawa(config)#ip route 10.0.0.0 255.0.0.0 193.18.4.2 Jawa(config)#exit Jawa# %SYS-5-CONFIG_I: Configured from console by console Jawa#copy running start Destination filename [startup-config]? Building configuration... [OK] Jawa#
- 10. Konfigurasi Router Kalimantan Router#conf term Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname Kalimantan Kalimantan(config)#int fa 0/0 Kalimantan (config-if)#ip address 10.10.11.1 255.0.0.0 Kalimantan (config-if)#no shut Jawa(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up Kalimantan (config-if)#exit Kalimantan (config)#int se 0/0 Kalimantan (config-if)#ip address 172.16.0.1 255.255.0.0 Kalimantan (config-if)#no shut
- 11. Kalimantan (config-if)# %LINK-5-CHANGED: Interface Serial0/1, changed state to up Kalimantan (config-if)#exit %LINK-5-CHANGED: Interface Serial0/0, changed state to down Kalimantan (config-if)#clock rate 64000 Kalimantan (config-if)#exit Kalimantan (config)#exit Kalimantan # %SYS-5-CONFIG_I: Configured from console by console Kalimantan #copy running start Destination filename [startup-config]? Building configuration... [OK] Konfigurasi Ip Route Kalimantan>enable Kalimantan#conf term Enter configuration commands, one per line. End with CNTL/Z. Kalimantan(config)# ip route 193.34.24.0 255.255.255.0 172.16.0.2 Kalimantan(config)# ip route 193.46.54.0 255.255.255.0 172.16.60.1 Kalimantan(config)#ip route 193.16.10.0 255.255.255.0 193.18.4.1 Kalimantan(config)#exit Kalimantan# %SYS-5-CONFIG_I: Configured from console by console Kalimantan#copy running start Destination filename [startup-config]? Building configuration...
- 12. [OK] Kalimantan#