Clap Pattern Based Electrical Appliance control

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395 -0056
Volume: 04 Issue: 02 | Feb -2017 www.irjet.net p-ISSN: 2395-0072
© 2017, IRJET | Impact Factor value: 5.181 | ISO 9001:2008 Certified Journal | Page 902
Clap Pattern Based Electrical Appliance control
Prof. Aditi Shukla1, Priyanka Patil2, Kanchan Nanaware3,Shital Salve4
1 Prof. Aditi Shukla, Dept. of E & TC Engineering, Sandip Foundation (SITRC) College Nasik, Maharashtra, India
2Priyanka Patil, Dept. of E & TC Engineering, Sandip Foundation (SITRC) College Nasik, Maharashtra, India
3 Kanchan Nanaware, Dept. of E & TC Engineering, Sandip Foundation (SITRC) College Nasik, Maharashtra, India
4 Shital Salve, Dept. of E & TC Engineering, Sandip Foundation (SITRC) College Nasik, Maharashtra, India
---------------------------------------------------------------------***---------------------------------------------------------------------
Abstract - In this paper, we present idea to control
Electrical Home Appliances like Light, TV, Fan, Bulb etc. using
Clap. There are various techniques available to control
Electrical Home Appliances such as IR based remote control
switch, ON OFF Switch, Using WIFI or Bluetooth Device
control. But our method is most cost effective. This project has
a big social impact. Our aim is that physically challengeduser.
We design PIC based circuit to detect clap from other sounds.
Key Words: Hand Clapping, Condenser microphone,
sampling LED, Relay, Clap trigger circuit etc.
1. INTRODUCTION
Now a day’s various methods are available for
controlling devices. Example simple ON OFF switch,
using SMS GSM based device is control, device control
using IR remote, device control using WIFI or
Bluetooth. These methods used for wired and wireless
technology for the purpose and each technology have
its own advantages and disadvantages. This projects
deals with low cost new technology to control device.
In clap pattern based electrical appliance control claps
is used to turn ON or turn OFF device. Idea of project is
when user claps for one time device one will turn 'ON'
and if user claps for two times devicetwowillturn'ON'
and if user claps for three times device three will turn
'ON' and two turn off device 1,2,3 user has to clap. For
one or two or three times respectively again. In this
project we are going to use PIC based suitable micro
controller and condenser microphone to accept clap
input from user.
2. LITERATURE SURVEY
2.1 Clap switching
This paper proposedbySomangshuBagchi,SubhadipGhosh,
Deepak Nandi present an clap switching work prior to
November 2013. In this project it gives knowledge of 555
timers, i.e. working of relay and clocks. In this type of device
it provide the working of NE555 timer and the relay. The
relay is switch it gives a path only when current flown
through it. In this project the second timer triggers relay of
conducting path it is established terminals of the load and
the device is gets turned on. Time interval of the claps is
checked with the time constant and it can be established by
the RC configuration of T=1.1R7*C3 [1].
2.2 Control of Light and Fan with Whistle and Clap
This paper proposed by Kashinath Murmu and Ravi Sonkar
present a Control of Light and Fan with Whistle and Clap
work prior accepted in November 2004. In this paper, it can
detect clap and whistle properly by removing most of the
noise. But it complicated to distinguishbetweenclapandtap
on a table the with the analog circuits due to similar
waveform generated by it [2].
2.3 Design of a clap activated switch
This paper is published Seyi Stephen olokede work prior
accepted in July-December 2008. In this paper the clap
activated switching device function properly by responding
to both hand claps at about three to four meter away and
finger tap sound at very close range, since both are low
frequency sounds and produce the same pulse wave
features. The resulting device is realizable, has good
reliability and its relatively inexpensive [4].
2.4 GA-Based Feature Extraction for Clapping
Sound Detection
This paper is published Jan Olajec, Roman Jarina, and Michal
Kuba present GA-Based Feature Extraction for Clapping
Sound Detection work from 25 September 2006. The results
of the experiment does not give clear result, in which
coefficient is more and less discriminative in the case of
detecting clapping sound among other sounds. But it is
valuable to notice the factsthat:a)theperformanceincreases
when only selected features are led to the classifier; b)
clearly, the highest and lowest MFCCs are more
discriminative that the coefficient fromthecentralpartofthe
MFCC feature vector. The future work on generic sound
detection will be oriented toward application of GA on wide
range of various spectro-temporal audiofeaturestogetmore
clear answer to the feature selection problem [5].

3. PROPOSED OF WORK
The clap pattern based electrical appliance control is based
on the patterns of claps. The claps are one, two, and three
likewise devices can be ON and OFF. In this the specific time
delay can be given to the microcontroller because by using
this microcontroller can read the triggering pulses.
4. BLOCK DIAGRAM
Fig-1: Block Diagram of Clap Pattern Based Electrical
Appliance control
 The above system consists of following blocks:
1. PIC microcontroller
2. IC 555 timer
3. Condenser MICROPHONE
4. Sampling LED
5. Power Supply
6. Oscillator
4.1 PIC microcontroller:-
In this block diagram we used the PIC18F2550
microcontroller it is a 28 pin IC. It has a flash type program
memory. Here we used the 256 prescalar for the delay
purpose.
4.2 Audio Amplifier:-
When we clap our hands, sound is captured by audio
amplifier. This sound is converted into the electrical signal
and then it is amplified by using transistors.
4.3 Condenser Microphone:-
A microphoneis an acoustic-to-electric transducer or sensor
that converts Sound into an electrical signal.
4.4 Monostable flip-flop:-
Mon stable multivibratorisknownasone-shotmultivibrator,
is a pulse generator circuit in which the duration of the pulse
determined by the R-C network, connected externally to the
555 timer. In sucha vibrator,one stateof outputisstable.For
auto triggering at output from quasi stable state to stable
stateenergy is stored by an externallyconnectedcapacitorto
reference level. The time taken in storage determines the
pulse width. The transition of output from stable state to
quasi stable state is accomplished by external triggering.
4.5 Sampling LED:-
For sampling led some specific time delay is given which is 4
sec is for on time and after every 4 sec it takes 5 sec delay.
4.6 IC 555 timer:-
It works as square-wave form generator with duty cycle
varying from 50 percent to 100 percent, Oscillator and can
also provide time delay in circuits.
4.7 Oscillator-
Oscillator is used to generate audio and radio frequency
energy. And the output of the oscillator sine wave output. It
has many shapes like square wave or saw-tooth wave. The
sinusoidal waveform in the form of ac or dc. Oscillator is a
very low power devices use in a radio frequency circuits.
Electronic oscillator related with a both produce sinusoidal
electrical energy. Output of the oscillator on a frequencies
measure in tens of a megahertz or the output produce of a
special oscillator at microwave frequencies. Oscillator
actually generates radio frequency output in the low power
transmitter most basic form.

5. FLOWCHART
Fig-2: Flowchart of Clap Pattern Based Electrical
Appliance control.
In above flowchart, when sampling LED is turn ON
then micro-controller will read clap triggering pulses from
clap trigger circuit. And when the sampling switch is OFF,
then it will check the triggering pulses coming from timer.
When triggering pulse is one then it will turn ON the first
device. When triggering pulse is two then it will turn ON the
second device. When triggering pulse is three then it will
turn ON the third device. When sampling LED is ON then
again it will read clap triggering pulses from clap triggering
circuit. When all devices turn ON then it takes 4 to 5 sec
delay.
When we want to OFF all devices, then it will again
check the sampling LED is ON. And if the sampling LED isON
then it will checks triggering pulses. It will only OFF the
already ON devices. When triggering pulse is one then it will
OFF the first device. When triggering pulse is two thenit will
OFF the second device. When triggering pulseis threethenit
will OFF the third device.
6. CONCLUSIONS
The main objective of this project is to design system to ON
OFF electrical appliance. Traditional clap switch control the
only one device, which is tedious and inefficient. By using
this, we can control multiple electrical appliances. The
resulting device is realizable, has good reliability and it is
relatively inexpensive. This project is useful for handicap
person.
REFERENCES
[1] Somangshu bagchi, shubhdip ghosh, Deepak Nandi
“Clapp switching” International journal of scientific and
engineering research, volume 4,issue 11, NOV 2013.
[2] Kashinath Murmu, Ravi Sonkar, “Control of Light and
Fan with Whistle and Clap Sounds” Department of
electrical engineering, IIT Bombay ,NOV 2004.
[3] Godfried T. Toussaint, “Recognization of hand clapping
sounds”, International journel of computer science and
electronics engineering volume1,issue 1 (2013).
[4] seyi stephen olkeede, "Design of clap activated switch",
Leonardo journal of sciences ISSN 1583-0233, ISSUE
13,JULY-DEC-2008.
[5] Jan Olajec, Roman Jarina, Michal Kuba “GA-Based
Feature Extraction for Clapping Sound Detection”
Faculty of electrical engineering, university of Belgrade,
Serbia September 25,2006.
[6] W. Ahmad and A. M. Kondoz, "Analysis and synthesis of
hand clapping sounds based on adaptive dictionary,"
Proceedings of the International Computer Music
Conference, University of Huddersfield, UK, 31 July -5
August, 2011.
[7] A. Jylhä and C. Erkut, "Inferring the hand configuration
from hand clapping sounds,"Proceedings of the 11th
International Conferenceon Digital AudioEffects(DAFx-
08), Espoo, Finland, September 1- 4, 2008.
[8] B. H. Repp, "The sound of two hands clapping: an
exploratory study, "Journal of the Acoustical Society of
America, vol. 81, no. 4 (April), 1100-1109, 1987.
BIOGRAPHIES
Prof. Aditi Shukla,
Dept. of E & TC Engineering,
Sandip Foundation(SITRC)college
Nashik,Maharashtra.
Priyanka Patil,
BE Student of E & TC Engineering,
Sandip Foundation (SITRC)college
Nashik, Maharashtra.

Kanchan Nanaware,
Shital Salve,

Clap Pattern Based Electrical Appliance control

More Related Content

What's hot (20)

Similar to Clap Pattern Based Electrical Appliance control (20)

More from IRJET Journal (20)

Recently uploaded (20)

Clap Pattern Based Electrical Appliance control