Co channel deployment cross layer approach for lte heterogeneous networks

IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 04 Issue: 06 | June-2015, Available @ http://www.ijret.org 397
CO-CHANNEL DEPLOYMENT CROSS LAYER APPROACH FOR LTE
HETEROGENEOUS NETWORKS
Deepthi Shree A.M1
, Arun Biradar2
1
Student, Department of CSE, East West Institute of Technology, Bangalore, Karnataka, India
2
Head of the Department, Department of CSE, East West Institute of Technology, Bangalore, Karnataka, India
Abstract
Nowadays Heterogeneous Networks (HetNets) are envisioned as the major capacity and performance enhancement enablers by
means of increasing the spectral efficiency per unit area. In LTE, since pico cells typically share the frequency band as macro
cells, the performance of a low-power pico access node could be severely impaired by interference from a high power macro
access node. In co-channel deployment it is necessary to balance the load and Share the resources between the different layers,
where macro and pico cells share the same carrier frequency. In this case, one of the main problem that need to be addressed in
order to improve the network performance is: Cell selection. For this reason we propose a throughput-based cell selection
algorithm. This algorithm targets to optimize the throughput of each user.
Keywords: LTE, Heterogeneous Networks, Macro cell, Pico cell and Co-Channel Deployment.
--------------------------------------------------------------------***----------------------------------------------------------------------
1. INTRODUCTION
In recent years, the development of wireless
communications has experienced a huge revolution. While
just a couple of decades ago mobile phones were mostly
used for making calls and sending messages via SMS, the
introduction of 3G, which allowed the use of broadband data
granting access to browse the internet, and later 4G, which
gets higher speeds, marked the development of mobile
broadband and data oriented devices such as smartphones
and USB modems. These devices are responsible for a fast
growth in mobile data traffic.
Mobile networks have to deal with the increase of the
number of devices and also the demands of users for higher
speeds to allow diversions like real time video streaming
and online games. Therefore, mobile networks have to
evolve in order to fulfill these demands. In the past years the
required increase in capacity would have been achieved by
adding more macro nodes in the network. However, the high
costs and the space needed for such an approach represent
an important problem for the operators. Moreover, spectral
efficiency per link is reaching theoretical limits. At the sight
of this, LTE-Advanced (LTE-A) in conjunction with
Heterogeneous Networks (HetNets) are seen as the keys for
further enhance the performance in mobile networks by
improving spectral efficiency per unit area.
LTE-A is a technology that was designed to meet the
demands of the growing traffic. It includes several advanced
techniques such as carrier aggregation, multiple-input
multiple-output (MIMO), and the introduction of HetNets. A
traditional homogeneous cellular network consists of a
group of high-power nodes (macro nodes). Heterogeneous
networks instead include not only macro but also low-power
nodes. This deployment allows to improve the spectral
efficiency per unit area, as the low-power cells make
possible to remove coverage holes in the macro-only
network and increase the capacity in zones with very high
traffic volume. The main characteristic of HetNets is the
great disparity between the transmit power used by the high-
power and the low-power nodes. This makes necessary the
usage of interference management techniques as low-power
nodes can suffer great interference from macro ones. A
throughtput-based cell selection algorithm is proposed to
optimize the throughput of each user.This is achieved by
choosing the best cell according to the estimated user
throughput that takes into account both the number of users
and the signal quality of the candidate cell, that means
received signal strength quality.
Fig -1 Architecture of LTE heterogeneous Networks
2. PROBLEM STATEMENT
In a heterogeneous network(Hetnet) a series of low power
pico nodes are distributed through the existing macro cell
network. The performance of low power pico nodes could
be severely impaired by interference from high power macro
nodes. In these networks when a new user equipment(UE)
enters in the networks determining the association rules that
decide which UEs should associated with which cells should

_______________________________________________________________________________________
be considered in efficient way. In this way a throughput-
based cell selection approach is a one of the good way to
improve the network performance.
3. RELATED RESEARCH WORK
In a co-channel deployment both macro and small cells
share the same frequency carrier. This may be the only
option if the available spectrum is limited. One of the key
feature to consider for the design of the network is UE cell
selection. There are few related works has been performed
on UE cell selection.
3.1 UE Cell Selection
In traditional homogeneous networks, the way of selecting
cell for an arriving UE is based on the UE measurement of
the received signal strength. The serving cell selected is the
one with the highest signal. There are different signal
strength indicators.
• Reference Signal Received Power (RSRP): which
measures for each cell the average of the power of the
resource elements that carry cell-specific reference signals
within the considered measurement frequency bandwidth.
This indicator reflects the received power from each cell.
• Reference Signal Received Quality (RSRQ): which is
calculated dividing RSRP by the total received power, thus
including the channel quality of the resources. This indicator
provides additional information useful in cases when RSRP
is not reliable enough for doing the cell selection or a
handover.
Usually in co-channel deployments the cell selection is done
based on the RSRP level. However, it is worth noticing that
macro cells have much larger coverage areas than the small
cells due to the large transmit power disparity between the
macro and small cells, resulting in few users served by the
small cells. It is desirable for the network to balance the load
between the macro and pico layers to harvest the gain from
cell splitting.
3.2 Load Based Cell Selection
The load-based cell selection approach focus on the load in
each cell as decision criterion.
Advantages: It considers the number of users divided by the
capacity of each layer as load measurement.
Disadvantages: This approach has the disadvantage of not
taking into account the channel quality in each cell.
3.3 Cell Selection Technique using RE
The cell selection technique using RE(Range expansion)
concentrate in the SINR(signal interference plus noise ratio),
in which the cell is selected with highest SINR, measuring it
during normal transmission subframes for macro cells and
during ABS subframes for pico cells.
Disadvantage: In this case the load in each cell is not
considered.
4. PROPOSED SYSTEM
4.1 System Architecture
In propose system, throughput-based cell selection approach
is introduced. Throughput-based cell selection algorithms
aim to balance the load among the cells by selecting the one
which offers best throughput, thus taking into account both
the load in each cell and the channel quality. The throughput
in each cell can be estimated based on a function of SINR
and number of users. This algorithm depends strongly on the
current condition of the network when choosing the serving
cell. Fig. 2 shows the architecture of our proposed idea.
Fig -2: System architecture of proposed approach.
4.2 Data Flow Diagram
Fig -3: Data flow diagram of throughput based algorithm.
5. IMPLEMENTATION
The throughput-based algorithm targets to optimize the
throughput of each user. This is achieved by choosing the
best cell according to the estimated user throughput that
takes into account both the number of users and the signal
quality of the candidate cell. This algorithm assumes that the
PF scheduler is applied, thus sharing the resources fairly
between all the users connected to a certain cell.

_______________________________________________________________________________________
5.1 Set of Feasible Candidate cells F Composition
The set of feasible candidate cells, F, is composed by every
cell i which fulfills the following condition:
( PRxmax / PRxi ) < ( 10^(RETHRESHOLD /10) )
Where:
• 𝑃𝑅𝑥𝑖 is the power received by the UE from cell i.
• 𝑃𝑅𝑥𝑚𝑎𝑥 is the maximum power received by the UE,
corresponding to the strongest signal the UE receives i.e.
𝑚𝑎𝑥𝑃𝑅𝑥𝑖.
• 𝑅𝐸𝑇𝐻𝑅𝐸𝑆𝐻𝑂𝐿𝐷(dB) is the maximum threshold allowed
between the maximum power received by the UE and 𝑃𝑅𝑥𝑖 .
The parameter RETHRESHOLD sets a condition check for
the selection of the candidate base stations. The objective of
this parameter is preventing the connection of the UE to a
base station(BS) with a very bad signal quality. This could
happen in a case where the network is very loaded and then
a BS with poor signal but with few users shows the best
theoretical throughput. In practice, connecting to a BS with
poor signal causes communication problems, and should be
avoided. The RETHRESHOLD value used in this study for
the throughput-based cell selection algorithm is 15 dB.
The conditional SINR is stable, and this stability is
important for the good performance of the throughput-based
algorithm. However, the conditional SINR is something
ideal that cannot be obtained in the real network. Each UE
can measure the channel quality in a certain moment. At that
moment, some BSs are transmitting and others are not. In
some other moment, the BSs transmitting may be different.
Thus, it is not possible for the UE to determine if all BSs are
transmitting at full power in order to obtain the conditional
SINR. It would be interesting to study in the future how to
adapt this algorithm so that it can be applied to a real
network.
5.2 Conditional SINR Estimation
The conditional Signal to interference plus noise ratio
(SINR) is estimated for each macro and pico cells
separately. The conditional SINR for macro cells are
computed as follows:
Γi = PRxi / (Interference + Noise)
The conditional SINR for pico cells are computed as follows:
Γi = PRxi / (Interference – PRxstrongest_macro + Noise)
Where:
• 𝑃𝑅𝑥𝑀𝑎𝑐𝑟𝑜𝑖 is the power received by the UE from Macro
“i”.
• 𝑃𝑅𝑥𝑃𝑖𝑐𝑜𝑖 is the power received by the UE from Pico “i”.
• 𝑃𝑅𝑥𝑆𝑡𝑟𝑜𝑛𝑔𝑒𝑠𝑡 𝑀𝑎𝑐𝑟𝑜 is the power received by the UE
corresponding to the strongest macro signal. This is the
strongest interferer for the potential pico UE.
• Interference is the total interference the UE suffers
assuming all BSs active.
• Noise is the thermal noise.
Γ𝑖 estimates the SINR the UE would have by connecting to
a certain base station with the assumption that the rest of
base stations are transmitting at full power (that is,
considering all BSs to be active). In the case of pico cells the
conditional SINR is computed assuming that the dominant
macro interferer is muted i.e. uses ABS all the time. Thus,
this estimation is optimistic for the pico cells as it is
subtracted the power of the strongest macro interferer.
Besides, the estimation is also optimistic for the macro base
stations as it is not considered that in muted subframes there
is no transmission available from the macro.
This approach for the estimation of the throughput does not
take into account the applied muting ratio in each cell.
Therefore, the cell selection is based just on the number of
users and the signal quality, which allows the algorithm to
balance the load among the cells, leaving the Fast ABS to
manage the resource partitioning.
5.3 Estimated Throughput Calculation
The estimated throughput the UE would get by connecting
to a certain candidate base station “i” is calculated according
to the following formula:
Ri = ( 1 / (Ni + 1) ) * BWi * log2 (1 + Γi )
Where:
• 𝑁𝑖 is the number of users in cells i.
• 𝐵𝑊𝑖 is the component carrier bandwidth of cell i.
• Γ𝑖 is the conditional SINR of the UE in cell i.
5.4 Serving Cell Selection
Every time when an UE arrives to the network, the serving
cell 𝑖* is selected as follows:
Where:
• 𝑅𝑖 is the estimated throughput of the UE in cells i.
• 𝐹 is the set of feasible candidate cells for the UE.
5.5 Pseudo-Code for Throughput Based Cell
Selection Algorithm
The pseudo-code for throughput-based cell selection
algorithm is represented as follows:
New user arrival
for ( each BSi ) do
if ( ( RSRPmax / RSRPi ) < ( 10^(RETHRESHOLD /10) ) )
then
if BSi is pico
Γi = RSRPi / (Interference – RSRPSTRONGEST_MACRO
+ Noise)
else //BSi is Macro

_______________________________________________________________________________________
Γi = RSRPi / (Interference + Noise)
end if;
Ri = ( 1 / (Ni + 1) ) * BWi * log2 (1 + Γi )
end if;
end for;
Select BS with max {Ri }
Where:
• BSi: every BS within reach of the new UE.
• RSRPi: RSRP that UE receives from BSi.
• RSRPmax: best RSRP, corresponding to the strongest
signal the UE receives.
• RSRPSTRONGEST_MACRO: RSRP that UE receives
from the macro cell with strongest signal.
• RETHRESHOLD (dB): maximum difference allowed
between best RSRP and RSRPi.
• Interference: total interference the UE suffers assuming all
base stations transmitting at full power.
• Noise: thermal Noise.
• Γi: Geometry Factor the UE would obtain connecting to
BSi.
• Ni : number of users connected to BSi.
• BWi: Component Carrier Bandwidth of BSi.
• Ri: estimated throughput the UE would obtain connecting
to BSi.
5.6 Advantages
In Heterogeneous Network, the Throughput-Based cell
selection approach determines the association rules that
decides which UEs should associate with which picos. This
approach mitigates the interference problem in an efficient
way. It does not considers the distance between nodes, it
performs scheduling based on the user equipment
throughput in each candidate cells. Thus it increases the
overall performance of the network.
6. CONCLUSION
LTE is the viable path for mobile broadband. In LTE
heterogeneous networks the network performance can be
improved by using throughput-based algorithm especially in
the case of co-channel deployment. This dynamic algorithm
gives a good solution for UE association rules where each
new entering UE can be associated with a cell based on its
throughput.
REFERENCES
[1] Magazine, pp. 10-21, June 2011.J. Clerk Maxwell, A
Treatise on Electricity and Magnetism, 3rd ed., vol.
2. Oxford: Clarendon, 1892, pp.68-73. A.
Damnjanovic, J. Montojo, Y. Wei, T. Ji, T. Luo, M.
Vajapeyam, T. Yoo, O. Song and D. Malladi, "A
Survey on 3GPP systems".
[2] K. I. Pedersen, Y. Wang, S. Strzyz and F.
Frederiksen, "Enhanced Inter Cell Interference
Coordination in Co-Channel Multi-Layer LTE
Advanced Networks," IEEE Wireless
Communications Magazine, pp.120-127, June 2013.
[3] S. Brueck, "Heterogeneous Networks in LTE-
Advanced," in 2011 8th Symposium on Wireless
Communication Systems, Aachen, 2011.
[4] Q. Ye, B. Rong, Y. Chen, C. Caramanis and J. G.
Andrews, "Towards and Optimal User Association in
Heterogeneous Cellular Networks," in IEEE Global
Communications Conference (GLOBECOM), 2012.
[5] D. López-Pérez, I. Güvenç, G. De la Roche, M.
Kountouris, T. Q. Quek and J. Zhang, "Enhanced
Intercell Interference Coordination Challenges in
Heterogeneous Networks," IEEE Wireless
Communications Magazine, pp. 22-30, June 2011.
[6] B. Soret, H. Wang, K. I. Pedersen and C. Rosa,
"Multicell Cooperation for LTE-Advanced
Heterogeneous Network Scenarios," IEEE Wireless
Communications Magazine, February 2013.
BIOGRAPHIES
Deepthi Shree A.M received her B.E in
computer science from Govt. engineering
college hassan, and pursuing her M.Tech
in CS in EWIT Bangalore.
Dr. Arun Biradar is HOD of the computer
science department in EWIT bangalore.
His area of specializations are computer
networks, wireless networks.

Co channel deployment cross layer approach for lte heterogeneous networks

More Related Content

What's hot (15)

Viewers also liked (15)

Similar to Co channel deployment cross layer approach for lte heterogeneous networks (20)

More from eSAT Journals (20)

Recently uploaded (20)

Co channel deployment cross layer approach for lte heterogeneous networks