Compact quasi self complementary elliptical disc

IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
__________________________________________________________________________________________
Volume: 03 Special Issue: 07 | May-2014, Available @ http://www.ijret.org 225
COMPACT QUASI SELF-COMPLEMENTARY ELLIPTICAL DISC
MONOPOLE ANTENNA WITH TAPERED MICROSTRIP FEED LINE
Jasmine Mannil Abraham1
, G. Josemin Bala2
1
PG Scholar, Department of Electronics and Communication Engineering, Karunya University, Tamil Nadu, India
2
Professor, Department of Electronics and Communication Engineering, Karunya University, Tamil Nadu, India
Abstract
In this paper a compact elliptical disc monopole antenna with tapered microstrip feed line for UWB application is proposed. The
antenna is designed using the quasi self -complementary technique for attaining electrical as well as physical size reduction. A
triangular notch is included in the ground plane for impedance matching between the antenna and the RF front end. The adoption of
this miniaturization technique has narrowed the impedance bandwidth of the antenna in the UWB range but lead to an additional
operating bandwidth in Ku band thereby exhibiting dual band behavior. This reduction in the bandwidth in the UWB range was
overcome by using the tapered microstrip feed line configuration. The antenna exhibited a wide impedance bandwidth extending
beyond the UWB range and hence could be used for both UWB as well as Ku band applications. The antenna has a physical
dimension of 16mm X 25mm corresponding to an electrical size of 0.24λ and was designed on an FR4 substrate with εr of 4.7. It is
seen that the antenna proposed here has led to 62% size reduction with a percentage impedance bandwidth of 123.46% when
compared with the conventional elliptical disc monopole antenna.
Keywords: Quasi self-complementary technique, planar monopole antennas, miniaturization, tapered microstrip feed line,
bandwidth enhancement, UWB antennas
----------------------------------------------------------------------***-----------------------------------------------------------------------
1. INTRODUCTION
The FCC (Federal Communications Committee) allocated a
bandwidth of 7.5GHz extending from 3.1 GHz to 10.6 GHz
for UWB (Ultra Wideband) applications. Since then UWB
technologies have evolved tremendously. The UWB is a
communication technology that occupies more than 500 MHz
bandwidth or greater than 25% operating frequency. UWB
technology has several advantages which has made it highly
attractive for consumer communication applications. It has
proved to be one of the most promising technologies for high
data rate wireless transmissions and has helped in improving
the services and facilities provided to the end users.
The advantages possessed by UWB antennas has led to an
increasing demand for improved performances, higher data
rate transmissions and synonymous operation with several
other techniques. Thus it was required to extend the antenna
performance beyond 10.6 GHz which is presently the upper
limit allotted by FCC for UWB systems. Apart from this there
has also been a greater demand for small and compact UWB
antennas as they could be easily incorporated in all mobile
electronics. A UWB antenna should not only be capable of
working over the entire UWB band assigned by the FCC but
also should be compact for the easy integration requirement of
the UWB systems. To sum it up, miniaturization and
bandwidth enhancement are two major concerns, in the
context of UWB antennas for which several techniques have
been adopted over the recent years.
Various miniaturization techniques have been adopted over
the past few decades to develop compact UWB antennas
whilst maintaining antenna performance [11-13]. Top loading
the back side of a microstrip fed elliptical monopole antenna
[13] has led to miniaturized physical size of 25 mm X 26mm.
The elliptical radiator was modified to obtain a better
performance in the higher frequency range. Reduced ground
plane effect was also employed to obtain a compact antenna
[7]. This effect was introduced by cutting a rectangular notch
from the patch and attaching an asymmetrical strip to the
radiator. The resulting antenna had a physical size of 25mm X
25mm and displayed considerable performance in the UWB
range. Antenna miniaturization can also be attained by
increasing the dielectric constant of the substrate [13]. The
surface wave excitations that may be caused by the use of a
substrate with higher dielectric constant can be removed by
reducing the thickness of the substrate. An antenna designed
using this technique can have a dimension of 20mm X 26 mm
physically. Techniques adopted for impedance bandwidth
enhancement for monopole antennas include ground plane
modification, tapered microstrip feed line and dual microstrip
feed line. Ground plane modification is the widely used
method which has proved to provide an impedance bandwidth
from 3.1 GHz to 12.6 GHz when used for an elliptical disc
monopole antenna [2]. The ground plane was modified from

__________________________________________________________________________________________
rectangular to half circular with sleeves included in the ground
plane for further enhancement of the impedance bandwidth.
The dual microstrip feed line when used in conjunction with a
circular patch gives considerable return loss performance up to
15 GHz when compared to a circular disc monopole antenna
fed with the conventional microstrip feed line [3].
Apart from all the miniaturization techniques available the
quasi self-complementary structure can be employed for
reducing the physical size of the antenna. The striking and the
most remarkable feature of this technique is that it can lead to
electrical size reduction along with the reduction in the
physical size. However it is seen that the antenna employing
this structure has a constant impedance of 188.5 Ω
irrespective of the antenna geometry thus requiring an external
impedance matching circuit to transform the 188.5 Ω
impedance of the antenna to the 50 Ω impedance of the RF
front end. This requirement limits the miniaturization that
could be attained by the antenna. To combat this,
modifications in the antenna geometry was taken up for
impedance matching. But this led to a reduction in the
impedance bandwidth of the antenna. In order to overcome
this bandwidth limitation, a tapered microstrip feed line is
used in conjunction with the quasi self-complementary
structure. Thus, in effect a compact UWB antenna design that
could operate over an enhanced bandwidth was obtained.
This paper presents a compact quasi self-complementary
elliptical disc monopole antenna fed by a tapered microstrip
feed line. Theoretically, an antenna designed using the QSC
technique has an impedance of 188.5Ω. Hence a matching
circuit is needed to transform the impedance of the antenna
from 188.5Ω to 50Ω in order to match the impedance of the
antenna with that of the RF front end. For this triangular notch
is included in the ground plane, thereby avoiding the use of
any external circuits for impedance matching and adding to
antenna miniaturization. The inclusion of notch for impedance
matching has reduced the impedance bandwidth of the antenna
over the UWB range. This defect was overcome by using a
tapered microstrip feed line and has led to an impedance
bandwidth extending up to the Ku band. An elliptical patch
and microstrip feed line was chosen to a circular patch and
CPW feed line respectively because it helps in achieving
better size reduction than the latter case. The performance of
this antenna is compared with a compact QSC antenna
employing a conventional microstrip feed line.
2. SELF-COMPLEMENTARY ANTENNA
The self-complementary antenna was first proposed by
Mushiake [14 and16]. He claimed that an antenna designed
using this technique can attain a broad impedance bandwidth.
Theoretically self-complementary antennas possess a constant
impedance of 188.5 Ω independent of the source frequency
and the antenna configuration. From [17] it is seen that a self-
complementary antenna can be represented by a pair of
complementary slot and dipole antenna as shown in Fig.1. The
terminals of the antenna, denoted by FF are separated by a
small infinitesimal distance as shown in Fig.1 (a) and Fig.1
(b). It is also assumed that the slot and the dipole are cut from
an infinitesimal thin plane, perfectly conducting sheet. The
ratio of the terminal voltage Vs to the terminal current Is gives
the driving point impedance Zs at the terminals of the slot
antenna shown in Fig. 1(a) while Zd is the ratio of the terminal
voltage Vd to the terminal current Id of the dipole antenna in
Fig. 1 (b). After derivations in [16], it is found that the product
of the impedances of two complementary antennas is the
constant Zo2
/4, where Zo is the intrinsic impedance of the
surrounding medium.
Frequency-independent impedance behavior can be achieved
if the antenna is its own complement. This is the self-
complementary property, in which the antenna and its
complement are identical. Through translation or rotation a
self-complementary structure can be made to exactly overlay
its complement. The value of impedance follows directly from
the equation, as noted by Mushiake:
Z=Zs =Zd = Zo /2 = 188.5Ω (1)
Fig -1: Slot antenna and its complementary dipole antenna
Therefore, in theory, a perfect self-complementary antenna on
an infinitely large plane has the constant input impedance
188.5 Ω, independent of the source frequency and the shape of
the antenna. Practically a self-complementary antenna has to
be truncated on a finite plane, which limits its bandwidth.
Furthermore, an impedance matching circuit for transforming
188.5 Ω to 50 Ω will further narrow the bandwidth and limit
the reduction of antenna size. In this paper a triangular notch
is included in the ground plane for matching the 188.5 Ω
impedance of the quasi self-complementary antenna to the 50
Ω impedance of the RF front end, thereby avoiding the use of
any external matching circuits and thus adding to the
advantage of higher miniaturization.

__________________________________________________________________________________________
3. ANTENNA DESIGN AND GEOMETRY
The design procedure for the compact quasi self-
complementary elliptical disc monopole antenna is shown in
Fig.2. At the initial stage a half elliptical patch is formed on
one side of the FR4 substrate with its slot counterpart on the
other side of the substrate which is made known in Fig. 2(a).
Next a tapered microstrip feed line is then added to the
radiator to excite it as shown in Fig. 2(b). Fig. 2(c) depicts the
final stage where a triangular notch is included in the ground
plane for impedance matching.
The compact quasi self-complementary elliptical disc
monopole antenna with tapered microstrip feed line proposed
in this paper is displayed in Fig.3. The antenna consists of a
semi-elliptical patch on one side of the FR4 substrate with
permittivity εr 4.7 and thickness 1.6mm. L and W denote the
length and the width of the dielectric substrate, respectively. A
and B represent the semi major and semi minor axes
respectively of the semi-elliptical patch. The dimensions of the
proposed antenna are displayed in Table 1. Additionally, in
order to enhance the impedance matching of the antenna, a
triangular notch is proposed on the ground plane. Ws and L2
represent the width and height of the triangular notch
respectively. A tapered microstrip feed line is included to
enhance the impedance bandwidth of the antenna which
otherwise was reduced due to the employment of the QSC
structure. CADFEKO simulation software was used for
simulating the antenna.
Fig -2: Design process of the compact quasi self-
complementary elliptical disc monopole antenna with tapered
microstrip feed line
Fig -3: Geometry of the proposed antenna
Table -1: Dimensions of the Proposed Antenna
Parameter Dimension (mm)
W 16
L 25
H 1.6
A 6
B 3.7
Ws 6
Wf 2.4
L1 8.9
L2 4.8
4. RESULTS AND DISCUSSIONS
The performance of the antenna is compared with that of the
QSC antenna employing a non-tapered microstrip feed line
[1]. Fig.4 and Fig.5 depict the front and back view of the QSC
elliptical disc monopole antenna without and with the tapered
feed line respectively. The triangular notch in the ground
plane included for ground plane for impedance matching can
be seen in Fig.4 (b) and Fig.5 (b). Fig.5 (a) depicts the tapered
microstrip feed line included for impedance bandwidth
enhancement.

__________________________________________________________________________________________
Fig -4: Front and back view of the compact QSC elliptical disc
monopole antenna
Both the antennas were designed using the quasi self-
complementary concept. The resulting antenna has a physical
dimension of 16mm X 25 mm corresponding to an electrical
equivalent of 0.24λ. The inclusion of the tapered microstrip
feed line combats the narrowing of the impedance bandwidth
caused due to the adoption of this technique for
miniaturization
Fig. 6 shows the 3-Dimensional radiation pattern of the
compact quasi self-complementary elliptical disc monopole
antenna with tapered microstrip feed line. From the figure it
can be seen that the antenna exhibits an omni directional
radiation pattern which is a required feature for a UWB
antenna.
Fig -5: Front and back view of the QSC elliptical disc
monopole antenna with tapered microstrip feed line
The impedance bandwidth of the antenna can be estimated
from the return loss graphs. From Fig.7, it is seen that the
compact QSC elliptical disc monopole antenna exhibits a
narrow impedance bandwidth on the UWB range. The
percentage impedance bandwidth of this antenna at fc1 as
7.83GHz is just 2.17%. This is because of the use of the notch
included in the ground plane for impedance matching. But, it
is seen that the antenna exhibits another band from 12.32GHz
to 15.53GHz with center frequency fc2 as 14.6GHz, hence
exhibiting dual band operation.
Fig -6: 3-Dimensional Radiation Pattern of the Proposed
Antenna
Fig.8 displays the return loss of the antenna proposed here. It
is seen that the antenna is capable of operating over the entire
UWB range and beyond thereby eliminating the issue in the
earlier case. The inclusion of the tapered microstrip feed line
has made the antenna capable of working over the UWB range
as well as the Ku band thereby making the antenna capable of
operating over a wider impedance bandwidth extending
beyond the UWB range. The percentage impedance bandwidth
of the proposed antenna with fc as 9.29GHz was calculated as
123.46%.
The Voltage Standing Wave Ratio is the parameter that
indicates how well the antenna matches to the transmission
line. A VSWR of unity is the best that indicates zero
reflections and return losses. But this is difficult to achieve for
UWB systems. Hence for UWB systems a VSWR <2 is
considered to be the best. The proposed antenna exhibits a
VSWR of 1.3 dB at fc.
Theoretically the impedance of an antenna must be equivalent
to 50Ω. Since quasi self-complementary technique was
adopted for miniaturizing the antenna, the antenna’s
impedance rose to 188.5Ω. This was practically brought down
to approximately 49.13Ω by using a triangular notch in the
ground plane thereby matching the impedance of the antenna
with that of the RF front end which is depicted in Fig.9

__________________________________________________________________________________________
Fig -7: Return Loss of the QSC elliptical disc monopole
antenna without the tapered microstrip feed line.
Fig -8: Return Loss of the QSC elliptical disc monopole
antenna with tapered microstrip feed line
Fig -9: Impedance of the QSC elliptical disc monopole
Miniaturization and impedance bandwidth enhancement being
the key parameters of concern here, a comparison between the
antenna proposed here and the conventional elliptical disc
monopole antenna is discussed at this point. It is seen that with
the adoption of the quasi self-complementary technique 62%
size reduction was attained when compared with the
conventional case. This technique has helped in size
diminishment both in the physical domain as well as in the
electrical domain as detailed in Table 2
Table -2: Comparison of the Size between the Conventional
Elliptical Disc Monopole Antenna with the Antenna Proposed
here
Antenna
Physical Size
(mm)
Electrical
Size (mm)
Conventional Elliptical Disc
Monopole Antenna
30 X 35 0.36λ
Compact Quasi Self-
Complementary Elliptical
Disc Monopole Antenna
with Tapered Microstrip
Feed Line
16 X 25 0.24λ
Chart -1: Bar chart comparing the impedance bandwidth of
the QSC elliptical disc monopole antenna in the UWB range,
Ku band and with that of the QSC elliptical disc monopole
The extent to which the tapered microstrip feed line proposal
has boosted the impedance bandwidth of the antenna is
discussed in Chart -1. The comparison is done between the
conventional elliptical disc monopole antenna, the compact
QSC elliptical disc monopole antenna with a microstrip feed
line and the antenna proposed here which is fed with the
tapered microstrip feed line. It is seen that the antenna
proposed here exhibits a considerable large percentage
impedance bandwidth of 123.46% when compared to the
compact antenna without the tapered feed line whose
impedance bandwidth in the UWB range was narrowed due to

__________________________________________________________________________________________
the inclusion of the notch in the ground plane. The antenna
proposed here thus, exhibits an ultra-wide impedance
bandwidth extending from the UWB range to the Ku band of
the spectrum
5. CONCLUSIONS
A compact quasi self-complementary elliptical disc monopole
antenna with tapered microstrip feed line was designed and
simulated here. The adoption of the quasi self-complementary
structure has led to 62% size reduction. The miniaturization
attained and the return loss performance of the proposed
antenna is compared with that of the conventional elliptical
disc monopole antenna and the compact quasi self-
complementary elliptical disc monopole antenna fed with a
microstrip feed line.
The quasi self-complementary structure espoused to
miniaturize the antenna has narrowed the impedance
bandwidth of the antenna in the UWB range although it led to
an additional operating band in the Ku region. This drawback
was overcome by feeding the antenna with a tapered
microstrip feed line. The resulting antenna has thus been able
to achieve both miniaturization and acceptable performance
over the UWB range and beyond
REFERENCES
[1]. Jasmine Mannil Abraham, Dr. Josemin Bala, “Compact
Quasi Self-Complementary Elliptical Disc Monopole
Antenna” ELECTRON5,Proceedings of the Fifth National
Conference on Recent Trends in Communication, Computing
and Signal Processing, vol.5,pp. 14-18, February 2014
[2]. Ashraf A. Adam, Sharul Kamal Abdul Rahim, Kim Geok
Tan and Ahmed Wasif Reza, “Design of 3.1–12 GHz Printed
Elliptical Disc Monopole Antenna with Half Circular
Modified Ground Plane for UWB Application”, Springer
Science and Transaction Media, vol. 69, pp.535–549, April
2012
[3]. Dr. Mohammed Matin, “Ultra Wide band Printed Antenna
Design”Ultra Wide Band Communication: Novel Trends-
Antennas and Propagation, 2011,vol. 1,pp. 1-207
[4]. Kalteh, A.-A., Fallahi, R., & Roozbahani, M. G.,” Design
of a band-notched microstrip circular slot antenna for UWB
communication.” Progress in Electromagnetics Research
C,2010, vol. 12, pp. 113–123
[5]. Behjati, Z., & Azarmanesh, M. N., “ Dual band-notched
semi-elliptical monopole antenna with two branch feed line.”,
Progress in Electromagnetics Research Letters,2009, vol.12,
pp.69–78.
[6]. Akhoondzadeh-Asl, L., Fardis, M., Abolghasemi, A., &
Dadashzadeh, G., “Frequency and time domain characteristic
of a novel notched frequency UWB antenna.”, Progress in
Electromagnetics Research,2008, vol. 80, pp. 237–348
[7]. Z.Chen, T.See and X.Qing, “Small Printed Ultra
wideband Antenna with Reduced Ground Plane Effect”, IEEE
Transactions on Antennas and Propagation, vol. 55, no. 2, pp.
383-388, February 2007
[8]. Zhou, H. J., Liu, Q. Z., Li, J. F.,&Guo, J. L., “A swallow-
tailed wideband planar monopole antenna with semi-elliptical
base”, Journal of Electromagnetic Waves and
Applications,2007, vol.21, no.9, pp.1257–1264.
[9]. Ray, K. P., & Rang, Y. ,”Ultra-wideband printed elliptical
monopole antennas”, IEEE Transactions on Antennas and
Propagation,2007, vol. 55, no.4, pp. 1189–1192.
[10]. Ren, W., Deng, J. Y., & Chen, K. S., “ Compact PCB
monopole antenna for UWB applications.”, Journal of
Electromagnetic Waves and Applications, 2007, vol.21, no.10,
pp.1411–1420.
[11]. A.M.Abbosh, M.E.Bialkowski, M.V.Jacob and
J.Mazierska, “Design of a compact ultra-wideband antenna”,
Microwave and Optical Technology Letter, vol. 48, pp. 1515-
1518, August 2006.
[12]. K. Bahadori and Y. Rahmat-Samii, “An Elliptic-Card
UWB Antenna for Wireless Communications”, The first
European Conference on Antennas and Propagation (EuCAP
2006), Nice, France, 6-10 November, 2006
[13]. T.Yang, W.A.Davis and W.L.Stutzman, “Small Planar
Ultra-wideband antenna with top-loading”, IEEE Antennas
and Propagation Society International Symposium 2005, pp.
479-482, July 2005.
[14]. MUSHIAKE, Y, “A report on Japanese development of
antennas: from the Yagi-Uda antenna to self-complementary
antennas”, IEEE Antennas Propag. Mag., 2004, vol. 46, no. 4,
pp. 47-60.
[15]. WONG, K., WU, T., SU, S., LAI, J., “Broadband printed
quasi-self-complementary antenna for 5.2/5.8 GHz WLAN
operation”, Microw. Opt. Technol. Lett., 2003, vol. 39, no. 6,
pp. 495-496
[16]. MUSHIAKE, Y, “Self-complementary antennas”, IEEE
Antennas Propag. Mag., 1992, vol. 34, no. 6, pp. 23-29.
[17]. KRAUS, J. Antennas for All Applications. McGraw-
Hill, Inc., 2002.

Compact quasi self complementary elliptical disc

More Related Content

What's hot (16)

Viewers also liked (20)

Similar to Compact quasi self complementary elliptical disc (20)

More from eSAT Publishing House (20)

Recently uploaded (20)

Compact quasi self complementary elliptical disc