COMPARISON ANALYSIS OF SHUNT ACTIVE FILTER AND TRANSFORMERLESS PARALLEL HYBRID ACTIVE FILTER

Jan Zizka (Eds) : CCSIT, SIPP, AISC, PDCTA - 2013
pp. 373–382, 2013. © CS & IT-CSCP 2013 DOI : 10.5121/csit.2013.3642
COMPARISON ANALYSIS OF SHUNT ACTIVE
FILTER AND TRANSFORMERLESS PARALLEL
HYBRID ACTIVE FILTER
Sakshi Bangia1
, P.R.Sharma2
and Maneesha Garg3
1,2
Department of Electrical Engineering, YMCA University Of Science and
Technology, Faridabad
1
sakshibangia@gmail.com,2
prsharma1966@gmail.com
3
Department of Humanities and Applied Science , YMCA University Of
Science and Technology, Faridabad
Garg_maneesha@yahoo.com
ABSTRACT
This research work presents the comparison analysis of Shunt Active Filter (SAF) with Parallel
Hybrid Active Filter (PHAF). The performances of SAF and PHAF have been analyzed with PI
controllers based on Synchronous Reference Frame theory. In each case, simulation is carried
out for three phase unbalanced non liner load conditions. The advantages of the designed
system and the proposed current reference calculation methods are verified by simulations
using MATLAB Power system Toolbox.
KEYWORDS
Power quality, shunt active filter, transformer-less shunt hybrid active filter, Total Harmonic
Distortion
1. INTRODUCTION
Harmonics are injected in source current due to the application of non-linear load. These
harmonic currents influence the function of other equipment connected on the similar distribution
feeder, including the harmonic producing loads. Among number of solutions conventionally
passive filters offers a low cost solution. They generally offer high series impedance or low shunt
impedance to block the particular harmonic content. However there are certain disadvantages like
fixed compensation characteristics and resonances with the source impedance. Thus in orders to
prevail over the demerits associated with traditional passive filters, Active Power Filters (APF)
have been introduced in recent years. APF plays a vital role for controlling the amount of
harmonic pollution present in a distribution system. They can be connected in series, shunt or
combination of series and shunt with the supply impedance.
Typically shunt APF consists of a three phase voltage source inverter with capacitor on dc side.
For large power applications, it is difficult to implement a low loss and a low cost PWM

374 Computer Science & Information Technology (CS & IT)
converter. When this equipment is connected in shunt to the ac source impedance it is possible to
improve the compensation characteristics of the passive filters in parallel connection [1], [2].This
forms the transformerless Parallel Hybrid Active Filter The aim of PHAF is to mitigate the
problems associated with SAF and passive filters and to complement and enhance their
performance by adding active or passive components to their structure [3].Figure 1 shows the
block diagram of transformerless parallel hybrid filter.
Figure 1. Block Diagram of Parallel Hybrid Active Filter
2. PRINCIPLE OF OPERATION
Hybrid active filters effectively mitigate the problems of a passive and an active filter and provide
cost-effective harmonic compensation, particularly for high-power nonlinear loads [4].The
parallel hybrid filter consists of three phase voltage source inverter with capacitor on the dc side
connected in shunt with the tuned passive filter. Shunt passive filter is a series combination of a
capacitor and a reactor tuned to a specific harmonic frequency. Since nonlinear load contributes
the major contribution of harmonics in the source current mainly due to lower order harmonics
thus tuned filter provides low impedance trap to harmonic. Remaining higher order harmonics
only are to be filtered by shunt active filter; hence its power rating can be reduced The
compensation of harmonics in the source current through enhancement of the compensation
characteristics of the passive filters also eliminates the chances of resonance [5].
The performance of the PHAF depends on the computation of reference compensating signal.
Among many control strategies mentioned for estimating the reference compensating current
Instantaneous Reactive Power (IRP) theory [6, 7] and Synchronous Reference Frame (SRF) are
mostly used. [8].These schemes employ the computation of the reference components through
subtraction of positive sequence fundamental current component from the load/source current.
These control strategies are very attractive for their simplicity and ease of implementation, but
lack in providing adequate solution under extreme or severe condition of fault conditions in

Computer Science & Information Technology (CS & IT) 375
passive filter branch. SRF control technique using proportional integral (PI) type controller are is
implemented to strength the currents of the filter to follow their reference values.
3. SYSTEM CONFIGURATION
A three phase parallel hybrid active filter is implemented for unbalance nonlinear load. The test
system consists of shunt connected active filter with shunt passive LC elements tuned 5th
harmonic frequency which the most prominent frequency is causing the distortion in source
current. Passive filters are designed to result in minimum Root Mean Square (RMS) value of
supply current at full load [9,10]. Proposal of Synchronous Reference Frame theory is included
in [11].
4. DESIGN PARAMETERS OF SHUNT ACTIVE FILTER
A shunt active filter consists of three phase, 6 pulse voltage source inverter. The line-line voltage
is considered as 415V. The design for dc bus capacitor, dc bus voltage and ac inductor are as
follows.
4.1. DC Capacitor Voltage
The minimum dc bus voltage should be greater than twice of the peak of the phase voltage of the
system [13]. The dc bus voltage is calculated as
V dc
=
m
V LL−
3
22
(1)
where, m is the modulation index =1 and is considered as 1 and VLL is the ac line voltage of
three phase source.
4.2. DC Bus Capacitor
The value of dc bus capacitor (Cdc)is given by
taIVVVC dcdcdc
)(3)]()[(
2
1 2
1
2
=− (2)
where, Vdc is the reference dc voltage and Vdc1 is the minimum voltage level of dc bus, a is the
over loading factor taken as 1.2, V is the phase voltage, I is the phase current and t is time by
which the dc bus voltage is to be recovered.
4.3. AC Filter
The ac inductance (Lf) depends on the current ripple icr,p-p, switching frequency fs, dc bus voltage
(Vdc) .Thus Lf is given as

Lf=
if
V
pcrps
dc
a
m
−
12
3
(3)
where, i crp-p ,= 5%
5. DESIGN PARAMETERS OF PASSIVE FILTER
The basic of shunt passive filter is to trap the tuned harmonic component in the source current
using LC circuit. At resonance frequency inductive reactance is equal to that of capacitive
reactance. Hence for single tuned filter, resonance frequency is given by
CL ff
f
π2
1
= (4)
Thus to design the size of capacitor, first step is to fixed the reactive power compensation .Hence
capacitance can be calculated by
filterkVAR
V
X LL
c
.
2
−
= (5)
where VL-L is line –line source voltage
kVAR is the fixed reactive power compensation
6. CONTROL STRATEGY
The main function of the SRF control strategy is to provide high resistance at the fundamental
frequency and also zero impedance is presented to harmonic current flowing in to the passive
filter. [12].The control diagram is shown in Fig 2.
Fig 2 Synchronous Reference Frame Control Scheme

In this three phase load current is transformed into d-q stationary reference frame using Parks
Transformation. Using this fundamental component appears as DC quantities and all other
harmonics are transformed as non-DC quantities. These quantities are not required hence these
can be filter out using low pass filter. The extracted dc components and are transformed back into
a–b–c coordinates to obtain the fundamental components of source currents. To compensate for
the inverter losses PI controller is applied to regulate the DC bus voltage.
The output of PI controller at the dc bus voltage of active filter is considered as the current (iloss)
for meeting its losses.
vkvvkii ndeidndendepdnlossnloss )()1()()1()(
)( +−+= −−
(6)
where, vv ndede )1( −
− is the error between the reference(vdc*) and sensed (vdc) dc
voltage at the nth sampling instant. Kpd and Kid are the proportional and the integral gains of the
dc bus voltage PI controller.
The reference source current is therefore expressed as,
iii lossddd
+=
*
(7)
Similarly PI controller is used to regulate reactive power
vkvvkii nteiqntentepqnqrsnqr )()1()()1()(
)( +−+= −−
(8)
The reference supply quadrature axis current is as
iii qrqdq
+=
*
(9)
where, vvv nsnte )(
*
)(
−= denotes the error between reference (vs*) and actual(vs(n)) terminal
voltage amplitudes at the n sampling instant. Kpq and Kiq are the proportional and the integral
gains of the PI controller.
7. MATLAB IMPLEMENTATION
A three phase transformerless hybrid active filter is implemented using MATLAB Power system
Toolbox. Three phase input source voltage of 415V, 50 Hz frequency with source resistance of
0.2 ohms and inductance of 2mH is considered. A three phase unbalance nonlinear load drawing
5A is considered for simulation. Shunt active filter is constituted of 6 pulse VSI with 2200 e-6F
of capacitance attached to the DC side. A small-rated filter has been included to minimize the
switching ripples at the inverter output. Passive elements of the filter are calculated using the
mathematical relation s considering 50% of fixed reactive compensation. Table1 gives the
detailed parameters of the system.

Table 1. Detailed Parameters of the System.
Parameters Values
Supply voltage 415V (L-L), 50 Hz
Loads: (i) Linear: phase a= 25
Phase b=10 and 80mH
Phase c =10 and 80 mH
(ii) Nonlinear: Three phase
full bridge rectifier drawing
15A
Shunt Active Filter:
Interfacing
Inductance
Lf = 5.5 mH
DC bus capacitance 22000e-6F.
Referenced Dc
voltage
750 V
Tuned Passive Filter C5=129.4e-6F ;L5=3.1mH
8. RESULTS AND DISCUSSION
The performance of the presented SRF control strategy is evaluated using by comparison of pure
shunt active power filter and parallel hybrid power filter. The three phase unbalance nonlinear
load considered here in the present system contains 5th harmonic content as the most prominent
factor which causes the distortion in the source current. Hence the passive elements of the hybrid
filter are tuned for the resonance frequency of 250Hz. The VA rating required for the inverter in
the hybrid filter is much lesser than that required in a pure shunt active filter.
The VA rating required of the inverter in parallel hybrid power active filter is given by
VA rating= 3
22
IV FMAXdc
××
Where I FMAX A13≅ is the maximum filter current.
Also the apparent power rating of nonlinear load is given by
VA rating= IV LrmsSrms
××3
Where VSrms and ILrms are the RMS value of source voltage taken as 415 V and load current taken
as 38A.
The apparent ratio of the parallel hybrid filter and nonlinear load is greatly reduced by 16%.
Another factor which determines the validation of active filters is Total Harmonic Distortion
(THD) is reduced from14.74 % to 2.65 % for phase a. Table II shows the THD for all three
phases for different types of filter. It can be seen from Fig 5 and Table III that parallel hybrid
filter system is able to reduce the 5th harmonic of supply current to 1.68% .The THD of the ac
supply current reduces to 3.27% with pure shunt active power filters alone as the major
component of the load current without any filter is composed of 5th harmonic.

TABLE III Harmonic Current in Percentage of Fundamental Current
5th 7th 11th 13th 17th 19th
Load current 12.76 5.42 3.92 2.23 1.55 0.97
Source current
with Passive Filter
0.20 2.69 2.57 1.64 1.13 0.89
Source current
with Pure Shunt
Active Filter
1.83 0.54 0.64 0.65 0.83 0.05
Source current
with Shunt Hybrid
Active Filter
1.68 1.03 0.23 0.21 0.19 0.13
Figure 3 shows the waveform of load current without filter. Fig 4 and 5 shows the waveform of
source current with pure shunt active filter and parallel hybrid active filter respectively. These
waveforms clearly illustrates that load current is very distorted that implies source current at this
time without filtering is also very distorted . With the application of power filter source currents
can be made sinusoidal .Clearly with the application of parallel hybrid active filter source current
is less distorted and contains less harmonics content as compared to pure shunt active filter. Fig 6
shows the uncompensated and compensated reactive power using parallel hybrid active filter
.Since the passive elements are tuned at fixed 50% compensation, fig 6 clearly validates the
passive parameters of hybrid filter. Fig7 demonstrates the source voltage, source current, load
voltage, load current, DC bus voltage, and filter current for parallel hybrid active filter.
TABLE II THD For Different Phases (in percentage)
Phase
Phase a Phas
e b
Phase
cType of filter
Load current
without filter
14.74 16.27 19.66
Pure shunt active
filter
3.27 4.58 3.75
Parallel hybrid filter 2.65 3.15 2.64

Figure 3 Load current
Figure 4 Source Current with Pure Active Filter
Figure 4 Source Current with Parallel Hybrid Active Filter
Figure 6 Load Reactive Power and Source Reactive power using parallel Hybrid Active Filter

Figure 7 Source Voltage, Source Current, Load Voltage, Load Current, DC Bus Voltage, Filter Current.
9. CONCLUSIONS
In this work, concept of transformerless parallel hybrid active filter is defined and verified by
MATLAB simulation. Simulation results verify that presented method has good performance in
the elimination of selective harmonic content and Total Harmonic Distortion. It has much better
dynamic response with less rating compared with the pure shunt active filter.
REFERENCES
[1] B. Singh, K. Al-Haddad, and A. Chandra, “A review of active filters for power quality improvement,”
IEEE Trans. Ind. Electron., vol. 46, no. 5, pp. 960–971, Oct. 1999.
[2] J.W. Dixon, G. Venegas, and L. A.Moran, “A series active power filter based on a sinusoidal current-
controlled voltage-source inverter,” IEEE Trans. Ind. Electron., vol. 44, no. 5, pp. 612–620, Oct.
1997.
[3] Bhattacharya,Divan,”Synchronous Frame based controller implementation for a hybrid series active
filter,Confeence record of IEEE Industry Apllications Conference Vol, 3,pp. 2531-2540 October
1995.
[4] S. Srianthumrong and H. Akagi, “A medium-voltage transformerless AC/DC power conversion
system consisting of a diode rectifier and a shunt hybrid filter,” IEEE Trans. Ind. Appl., vol. 39, no. 3,
pp. 874–882, May/Jun. 2003.
[5] H. Fujita, T. Yamasaki and H. Akagi, "A hybrid active filter for damping of harmonic resonance in
industrial power systems," IEEE Trans. on Power Electronics, vol. 15, no. 2, pp. 215-222, March
2000.

[6] H. Fujita, H. Akagi, "A Practical Approach to Harmonic Compensation in Power Systems-Series
Connection of Passive, Active Filters," IEEE Trans. on Ind.. Appl., vol.27, no.6, pp. 1020-1025,
Nov./Dec. 1991.
[7] F.B. Libano, J.A.Cobos, J. Uceda, "Simplified control strategy for Hybrid Active Filters", IEEE
PESC Record, 1 997, pp 1102-1108.
[8] P.T. Cheng, S. Bhattacharya and D. Divan, "Experimental Verification of Dominant Harmonic Active
Filter for High Power Applications",IEEE Trans. on Ind. Appl., vol. 36, pp.567-577, March/April,
2000.
[9] IEEE Guide for Application and Specification of Harmonic Filters IEEE Std 1531-2003.
[10] V, Verma, S. Shanker, B. Singh, A. Chandra, and Kamal Al- Haddad, "Genetic Algorithm Based
Design of Passive Filters for Offshore Applications," Proc. ofIEEE PCIC '04, 2004, pp 55-62.
[11] S. Bhattacharya, D. Divan and B. Banerjee, “Synchronous frame harmonic isolator using active series
filter,” EPE-Firenze, Vol. 3, pp. 30-35, 1991.
[12] V, Verma, S. Shanker, B. Singh,’Design and Implemention of Current Controlled Parallel Hybrid
Power Filter.
[13] B.N.Singh, P.Rastgoufard, B.Singh, A.Chandra and K.Al.Haddad, “Design,simulation and
implementation of three pole/ four pole topologies for active filters,” IEE Eletr. Power Appl., vol.
151, no. 4, pp. 467-476, July 2004.
Authors
Sakshi Bangia received the B.Tech degree in Instrumentation and Control from MDU
Rohtak and M.Tech degree in Electrical Engg. from YMCA UST in 2004 and 2006,
respectively. She is pursuing Ph.D in Power Quality from Maharishi Dayanand
University, India. Presently she is working as Assistant Professor in Electrical
Engineering Department at YMCA UST Faridabad.
Dr. P.R.Sharma was born in 1966 in India. He is currently working as Chairman of
the Department in Electrical Engg. in YMCA University Of Science and
Technology, Faridabad. He received his B.E Electrical Engineering in 1988 from
Punjab University Chandigarh, M.Tech in Electrical Engineering (Power System)
from Regional Engineering College Kurukshetra in 1990 and Ph.D from
M.D.University Rohtak in 2005. He started his carrier from industry. He has vast
experience in the industry and teaching. His area of interest is Optimal location and
coordinated control of FACTS devices ,power system stability and control
Dr. Maneesha Garg did her Ph.D(Physics) in 2002 from Kurukshetra University,
India. After that she worked as Research Associate granted by CSIR, in NIT
Kurukshetra for 4 years. She has 18 publications in national, international journals
and more than 30 papers in conferences to her credit. Presently she is working as
Assistant Professor in Humanities and Applied Science Department, YMCA UST,
Faridabad and guiding 4 scholars for their research work.

COMPARISON ANALYSIS OF SHUNT ACTIVE FILTER AND TRANSFORMERLESS PARALLEL HYBRID ACTIVE FILTER

More Related Content

What's hot (17)

Similar to COMPARISON ANALYSIS OF SHUNT ACTIVE FILTER AND TRANSFORMERLESS PARALLEL HYBRID ACTIVE FILTER (20)

More from cscpconf (20)

Recently uploaded (20)

COMPARISON ANALYSIS OF SHUNT ACTIVE FILTER AND TRANSFORMERLESS PARALLEL HYBRID ACTIVE FILTER