Congestionin Data Networks
Download as PPT, PDF0 likes949 views
The document discusses congestion in data networks. It defines congestion as occurring when the number of packets being transmitted approaches the network's handling capacity. This can cause packets to be lost if buffers fill up. Mechanisms for congestion control include backpressure from congested nodes to slow down incoming traffic, choke packets sent to sources to cut back transmission, and implicit or explicit signaling of congestion levels to sources. Frame relay and ATM networks employ various techniques for traffic management, policing, and scheduling to control congestion and meet quality of service guarantees for different connections.
Congestionin Data Networks
- 1. Congestion in Data Networks
- 2. What Is Congestion? Congestion occurs when the number of packets being transmitted through the network approaches the packet handling capacity of the network Congestion control aims to keep number of packets below level at which performance falls off dramatically Data network is a network of queues Generally 80% utilization is critical Finite queues mean data may be lost
- 3. Queues at a Node
- 4. Effects of Congestion Packets arriving are stored at input buffers Routing decision made Packet moves to output buffer Packets queued for output transmitted as fast as possible Statistical time division multiplexing If packets arrive to fast to be routed, or to be output, buffers will fill Can discard packets Can use flow control Can propagate congestion through network
- 6. Ideal Network Utilization
- 7. Practical Performance Ideal assumes infinite buffers and no overhead Buffers are finite Overheads occur in exchanging congestion control messages
- 8. Effects of Congestion - No Control
- 9. Mechanisms for Congestion Control
- 10. Backpressure If node becomes congested it can slow down or halt flow of packets from other nodes May mean that other nodes have to apply control on incoming packet rates Propagates back to source Can restrict to logical connections generating most traffic Used in connection oriented that allow hop by hop congestion control (e.g. X.25) Not used in ATM nor frame relay Only recently developed for IP
- 11. Choke Packet Control packet Generated at congested node Sent to source node e.g. ICMP source quench From router or destination Source cuts back until no more source quench message Sent for every discarded packet, or anticipated Rather crude mechanism
- 12. Implicit Congestion Signaling Transmission delay may increase with congestion Packet may be discarded Source can detect these as implicit indications of congestion Useful on connectionless (datagram) networks e.g. IP based (TCP includes congestion and flow control - see chapter 17) Used in frame relay LAPF
- 13. Explicit Congestion Signaling Network alerts end systems of increasing congestion End systems take steps to reduce offered load Backwards Congestion avoidance in opposite direction to packet required Forwards Congestion avoidance in same direction as packet required
- 14. Categories of Explicit Signaling Binary A bit set in a packet indicates congestion Credit based Indicates how many packets source may send Common for end to end flow control Rate based Supply explicit data rate limit e.g. ATM
- 15. Traffic Management Fairness Quality of service May want different treatment for different connections Reservations e.g. ATM Traffic contract between user and network
- 16. Congestion Control in Packet Switched Networks Send control packet to some or all source nodes Requires additional traffic during congestion Rely on routing information May react too quickly End to end probe packets Adds to overhead Add congestion info to packets as they cross nodes Either backwards or forwards
- 17. Frame Relay Congestion Control Minimize discards Maintain agreed QoS Minimize probability of one end user monoply Simple to implement Little overhead on network or user Create minimal additional traffic Distribute resources fairly Limit spread of congestion Operate effectively regardless of traffic flow Minimum impact on other systems Minimize variance in QoS
- 18. Techniques Discard strategy Congestion avoidance Explicit signaling Congestion recovery Implicit signaling mechanism
- 19. Traffic Rate Management Must discard frames to cope with congestion Arbitrarily, no regard for source No reward for restraint so end systems transmit as fast as possible Committed information rate (CIR) Data in excess of this liable to discard Not guaranteed Aggregate CIR should not exceed physical data rate Committed burst size Excess burst size
- 20. Operation of CIR
- 21. Relationship Among Congestion Parameters
- 22. Explicit Signaling Network alerts end systems of growing congestion Backward explicit congestion notification Forward explicit congestion notification Frame handler monitors its queues May notify some or all logical connections User response Reduce rate
- 23. ATM Traffic Management High speed, small cell size, limited overhead bits Still evolving Requirements Majority of traffic not amenable to flow control Feedback slow due to reduced transmission time compared with propagation delay Wide range of application demands Different traffic patterns Different network services High speed switching and transmission increases volatility
- 24. Latency/Speed Effects ATM 150Mbps ~2.8x10 -6 seconds to insert single cell Time to traverse network depends on propagation delay, switching delay Assume propagation at two-thirds speed of light If source and destination on opposite sides of USA, propagation time ~ 48x10 -3 seconds Given implicit congestion control, by the time dropped cell notification has reached source, 7.2x10 6 bits have been transmitted So, this is not a good strategy for ATM
- 25. Cell Delay Variation For ATM voice/video, data is a stream of cells Delay across network must be short Rate of delivery must be constant There will always be some variation in transit Delay cell delivery to application so that constant bit rate can be maintained to application
- 26. Time Re-assembly of CBR Cells
- 27. Network Contribution to Cell Delay Variation Packet switched networks Queuing delays Routing decision time Frame relay As above but to lesser extent ATM Less than frame relay ATM protocol designed to minimize processing overheads at switches ATM switches have very high throughput Only noticeable delay is from congestion Must not accept load that causes congestion
- 28. Cell Delay Variation At The UNI Application produces data at fixed rate Processing at three layers of ATM causes delay Interleaving cells from different connections Operation and maintenance cell interleaving If using synchronous digital hierarchy frames, these are inserted at physical layer Can not predict these delays
- 29. Origins of Cell Delay Variation
- 30. Traffic and Congestion Control Framework ATM layer traffic and congestion control should support QoS classes for all foreseeable network services Should not rely on AAL protocols that are network specific, nor higher level application specific protocols Should minimize network and end to end system complexity
- 31. Timings Considered Cell insertion time Round trip propagation time Connection duration Long term Determine whether a given new connection can be accommodated Agree performance parameters with subscriber
- 32. Traffic Management and Congestion Control Techniques Resource management using virtual paths Connection admission control Usage parameter control Selective cell discard Traffic shaping
- 33. Resource Management Using Virtual Paths Separate traffic flow according to service characteristics User to user application User to network application Network to network application Concern with: Cell loss ratio Cell transfer delay Cell delay variation
- 34. Configuration of VCCs and VPCs
- 35. Allocating VCCs within VPC All VCCs within VPC should experience similar network performance Options for allocation: Aggregate peak demand Statistical multiplexing
- 36. Connection Admission Control First line of defense User specifies traffic characteristics for new connection (VCC or VPC) by selecting a QoS Network accepts connection only if it can meet the demand Traffic contract Peak cell rate Cell delay variation Sustainable cell rate Burst tolerance
- 37. Usage Parameter Control Monitor connection to ensure traffic cinforms to contract Protection of network resources from overload by one connection Done on VCC and VPC Peak cell rate and cell delay variation Sustainable cell rate and burst tolerance Discard cells that do not conform to traffic contract Called traffic policing
- 38. Traffic Shaping Smooth out traffic flow and reduce cell clumping Token bucket
- 39. Token Bucket for Traffic Shaping
- 40. GFR Traffic Management Guaranteed frame rate is as simple as UBR from end system viewpoint Places modest requirements on ATM network elements End system does no policing or shaping of traffic May transmit at line rate of ATM adaptor No guarantee of delivery Higher layer (e.g. TCP) must do congestion control User can reserve capacity for each VC Assures application may transmit at minimum rate without losses If no congestion, higher rates maybe used
- 41. Frame Recognition GFR recognizes frames as well as cells When congested, network discards whole frame rather than individual cells All cells of a frame have same CLP bit setting CLP=1 AAL5 frames are lower priority Best efforts CLP=0 frames minimum guaranteed capacity
- 42. GFR Contract Parameters Peak cell rate (PCR) Minimum cell rate (MCR) Maximum burst size (MBS) Maximum frame size (MFS) Cell delay variation tolerance (CDVT)
- 43. Mechanisms for Supporting Rate Guarantees (1) Tagging and policing Discriminate between frames that conform to contract and those that don’t Set CLP=1 on all cells in frame if not Gives lower priority Maybe done by network or source Network may discard CLP=1 cells Policing Buffer management Treatment of buffered cells Congestion indicated by high buffer occupancy Discard tagged cells Including ones already in buffer to make room To be fair, per VC buffering Cell discard based on queue-specific thresholds
- 44. Mechanisms for Supporting Rate Guarantees (2) Scheduling Give preferential treatment to untagged cells Separate queues for each VC Make per-VC scheduling decisions Enables control of outgoing rate of VCs VCs get fair capacity allocation Still meet contract
- 45. Components of GFR System
- 46. Conformance Definition UPC Monitors each active VC Ensure traffic conforms to contract Tag or discard nonconforming cells Frame conforms if all cells conform Cell conforms if: Rate of cells within contract All cells in frame have same CLP Frame satisfies MFS parameter (check for last cell in frame or cell count < MFS)
- 47. QoS Eligibility Test Two stage filtering process Frame tested for conformance to contract If not, may discard If not discarded, tag Sets upper bound Penalize cells above upper bound Implementations expected to attempt delivery of tagged cells Determine frames eligible for QoS guarantees Under GFR contract for VC Lower bound on traffic Frames making up traffic flow below threshold are eligible
- 48. GFR VC Frame Categories Nonconforming frame Cells of this frame will be tagged or discarded Conforming but ineligible frames Cells will receive a best-effort service Conforming and eligible frames Cells will receive a guarantee of delivery
- 49. Required Reading Stallings chapter 1 3