Demonstrating warehousing concepts through interactive animations

1 / 17
Gurarslan, O., Guler, Y. H., Sahin, H., Ertek, G., Ozguven, K., Cacina, S. and Akkas, A. C. (2006).
"Demonstrating warehousing concepts through interactive animations.” 5th International
Symposium on Intelligent Manufacturing Systems, Sakarya, Turkey.
Note: This is the final draft version of this paper. Please cite this paper (or this final draft) as
above. You can download this final draft from http://research.sabanciuniv.edu.
Demonstrating Warehousing Concepts
Through Interactive Animations
Omer Gurarslan1, Yigit Huseyin Guler2, Hasan Sahin2,
Gurdal Ertek2, Kutluk Ozguven2,
Sehmuz Cacina2, Ali Can Akkas2
1 Faculty of Management
Sabanci University, Orhanli, Tuzla, 34956, Istanbul, Turkey
2 Faculty of Engineering and Natural Sciences
Sabanci University, Orhanli, Tuzla, 34956, Istanbul, Turkey

2 / 17
Abstract
In this paper, we report development of interactive computer animations to
demonstrate warehousing concepts, providing a virtual environment for learning.
Almost every company, regardless of its industry, holds inventory of goods in its
warehouse(s) to respond to customer demand promptly, to coordinate supply and
demand, to realize economies of scale in manufacturing or processing, to add
value to its products and to reduce response time. Design, analysis, and
improvement of warehouse operations can yield significant savings for a company.
Warehousing science can be considered as an important field within the industrial
engineering discipline. However, there is very little educational material
(including web based media), and only a handful of books available in this field.
We believe that the animations that we developed will significantly contribute to
the understanding of warehousing concepts, and enable tomorrow’s practitioners
to grasp the fundamentals of managing warehouses.
Submission areas: Virtual Worlds, Manufacturing Systems Engineering
Introduction
Warehousing
Warehousing is a critical function that can be found in almost every supply chain. Since
warehousing typically is one of the top three cost contributors (together with transportation and
inventory carrying costs), effective warehouse planning and management can significantly
increase the competitiveness of a company.

3 / 17
Typical operations in a warehouse are receiving of inbound materials, put away to reserve and
forward storage/picking areas, replenishment of the forward areas from the reserve areas, and
picking, sorting, packing, and shipping orders. Warehouse planning and management begins
with determining the strategic decision of which distribution strategy to employ. Then, the
tactical decisions of selecting the equipment and setting the warehouse layout are made.
Another tactical decision is the allocation of product groups to the areas within the warehouse.
The strategy of zoning divides the warehouse into weakly linked zones where order picking takes
place with dedicated labor for each zone. Another, important decision is whether to batch in the
picking of incoming orders or not. Finally, operational decisions such as determining the labor
schedule and the routings of order pickers are made.
The most comprehensive resources on warehousing that we have found and used in our work
are the following:
 Frazelle (2002) not only provides a fascinating introduction to warehousing concepts, but
also gives great insight on how to operate a warehouse efficiently. This book is intended
mainly for practitioners and does not include any mathematical models.
 Bartholdi and Hackman (forthcoming) have made their lecture notes available on the
Internet in the form of a book titled “Warehousing and Distribution Science”. This book,
discusses the results of fundamental research studies on warehousing, besides serving as
an introductory resource.
 The Progress Group1, a logistics and supply chain consulting company, has made several
white papers available at their web site. These papers are great reads for those interested
in learning experts’ insights on a variety of topics in supply chain and warehouse
planning.
Our work is primarily based upon the information and insights presented in the above three
resources. We have singled out the concepts that we believe are crucial, and built interactive
animations for each, as will be explained in detail in the next section.
1
http://www.theprogressgroup.com/

4 / 17
E-Learning
In the last ten years, as in all disciplines, there have been attempts in the area of logistics
management to train or educate students or workforce with the help of electronic learning and
distance education at various levels, including corporate training programs, blue collar
employee capabilities enhancement, masters programs and undergraduate level courses.
Although there are many alternative definitions, a description can be “E-Learning is the use of
digital and internet technologies to create experiences that educate our fellow human beings”
(Horton 2001).
It is possible to classify electronic learning activities from various aspects: Automation as
opposed to the human tutor involvement, community management tools employed and the level
of interaction, amount of games and simulations as opposed to traditional reading materials. In
the age of internet and computer animation based games as the primary pastime of students,
and when there are a number of various possibilities that attract them including films or
activities, traditional classroom education that is not supplemented by some of the e-learning
activities such as interactive multimedia animations a valuable resource is not utilized.
Therefore in this study it is decided that in the teaching of logistics planning interactive
animations that are characteristic in online education are to be used. This approach is expected
to explain in depth the main concepts in warehousing.
Macromedia Flash
We have used the Macromedia Flash software2 in creating our animations. The greatest
advantages of this software -that played role in our selection- are the following:
 The animations created in Macromedia Flash can be viewed in practically any operating
system and over the internet.
 A great percentage of internet users already have Flash Viewer installed on their
computers.
2
http://www.macromedia.com

5 / 17
 The animation files have very small sizes, due to the use of vectoral graphics.
 The Macromedia Corporation is owned by the Adobe Corporation3 which has a strong
presence on the Internet and a great influence in the software industry. The well-known
Adobe Acrobat format (.pdf files) is the universal format in the academic and business
world.
 The “action script” programming language within Macromedia Flash enables developers
to create easy-to-use GUIs (Graphical User Interfaces) and offers many of the capabilities
of a general purpose programming language (such as C++).
In designing and implementing our animation one issue that we paid attention to was to make
sure that all the animations share the same characteristics with respect to interface: We used the
same set of buttons, same set of font sizes and the same height-to-weight ratios in all the
animations. We believe that this approach will help the users to perceive the animations as
components of an integrated whole.
Related Work
Engineering Education Literature
One can find articles in engineering education literature that present impressive educational
materials in various fields of engineering: Leung et al. (2001) report the development and
classroom use of an animated simulation package to teach electromagnetic theory. Ong and
Mannan (2002) describe a web-based courseware to teach concepts and principles in
metalworking, focusing on metallurgy aspects. Their system is developed using Macromedia
Flash (as in our work) together with MS Front Page web authoring system. The last example that
we have chosen to mention is the system developed by Ettouney et al. (2000) for the design and
3
http://www.adobe.com

6 / 17
simulation of thermal desalination process. This system has been used extensively in graduate,
undergraduate, and training classes with great success.
Internet Resources
Bartholdi has made available on the internet several computational tools4 to accompany
Bartholdi and Hackman (forthcoming). One of these is a visualization program developed using
Visual Basic that reads a MS Access database and a MS Excel spreadsheet, and gives a colored
bird’s eye view of a warehouse. This tool can be used in warehousing education within an
engineering curriculum.
Another source available on the internet is the Interactive Warehouse5 Java applet created by
Roodbergen. The Interactive Warehouse allows users to learn about methods for determining
order picking routes, which were compared earlier in an article by Roodbergen and De Koster
(2001). The applet walks the user through the steps of setting a warehouse layout, creating an
order, creating a route, selecting a routing method, and viewing the results.
These are the only two sources that we have been able to find on the internet.
The Animations Developed
Distribution Strategies
This animation illustrates the three basic distribution strategies of traditional distribution (with
a warehouse), direct shipment, and crossdocking (Simchi-Levi et al., 2003, p133-136). We
believe that this animation should be the first animation to show in an introductory
4
http://www.tli.gatech.edu/whscience/supplement.html
5
http://www.roodbergen.com/warehouse/

7 / 17
warehousing presentation, since it gives an overview and a general understanding of a
warehouse (and a crossdocking facility) within the general context of a supply chain. In
traditional distribution the warehouse serves as a storage point, where products incoming from
the suppliers are putaway to various locations in the warehouse to be stored for some time
(which can be in the magnitude of years) and then picked for shipment to demand points
(Figure 1a). Direct shipment takes place when the supplier sends its shipments directly to
demand points, bypassing the warehouse (Figure 1b). In crossdocking, the suppliers’ trucks do
visit the so called “crossdock facility”, but the products are not stored for more than 24 hours
(Figure 1c). Crossdocking can bring significant cost savings but should be carefully planned and
coordinated.
Order Picking Schemes
Next animation that we present summarizes the picking schemes in a warehouse. Freeform
picking takes place when there is no zoning in the warehouse. In this scenario, two possibilities
are single order picking and the batch picking (Figure 2a). In single order picking, the order
picker travels on a new route to pick each new order (Figure 1b). In batch picking, the order
picker picks two or more orders on the same route.
In zone picking, each order picker is allocated to a particular zone, and is responsible of picking
the orders in his/her zone. Since the items within the same order may be picked at different
zones simultaneously, there is a need to combine these picks into a single whole. Two strategies
to achieve this are progressive assembly and downstream sortation. In progressive assembly the
first order picker picks the items in an order that reside in his/her zone, and puts the tote/box
containing the incomplete order to the origin point for the second zone (Figure 2c). The next
order picker seizes what the preceding order picker has accumulated and continues picking the
items in the order that reside in his/her region.
In downstream sortation strategy, the order picker in each zone leaves the incomplete order that
he picked into a conveyor, and the conveyor carries the totes/boxes to a sortation point (Figure
2d).

8 / 17
(a) (b)
(c)
Figure 1. Distribution Strategies

9 / 17
(a)
(b)
Figure 2. Picking Schemes in a Warehouse

10 / 17
(c)
(d)
Figure 2 (continued). Picking Schemes in a Warehouse

11 / 17
Pick-to-light System
Order picking in most warehouses involves minimal technology. A typical order picking tour
starts with receipt of a picking list, which displays the item number (also referred to as SKU
number, standing for Stock Keeping Unit), the item location and the number of units to pick.
The order picker sorts the items to be picked in his mind, and visits each item’s location to make
the picks (Figure 3a). Tasks that consume time during this classical mode of order picking are
traveling, searching, extracting and documenting.
(a)

12 / 17
(b)
Figure 3. Pick-to-light System
One problem encountered in most order picking operations is the erroneous picking of items. A
pick-to-light system is a solution that technology offers to reduce the times for the mentioned
tasks and to reduce order picking errors (Figure 3b). In a pick-to-light system, an indicator light
and an electronic numeric display inform the order picker on where to pick from and in what
quantity. The order picker is relieved from the burden of searching the item locations and -to a
degree- relieved from other tasks. Picking errors are also observed to decrease when pick-to-
light systems are implemented. Thus the pick-to-light system is a viable option that can reduce
costs and increase order picking accuracy in a warehouse.
Bucket Brigade
Let us consider a forward pick area, where a number of order pickers (for example three of
them) perform picking at varying speeds. A fundamental question is the following: How should

13 / 17
the order pickers be placed on this picking line? Two alternatives that come to mind
immediately are sorting the pickers from the slowest to fastest and sorting them from the fastest
to the slowest. Theoretical and empirical research by Bartholdi and Eisenstein (2006) show that
the former is indeed the optimal alternative. The bucket brigade animation that we have
developed illustrates how this takes place through animation. The user can observe in the fast-
normal-slow picker sequence (the simulation below) how the slow picker blocks the progress of
the fast picker. In the slow-normal-fast picker sequence (operating mode) the fast picker clears
out any material downstream and takes over the work upstream from the slow picker.
Figure 4. Bucket Brigade
Carousel
Carousels are automated equipments that store small items in the shelves of their carriers and
bring the items to order pickers (Figure 5). In practice two or three carousels are assigned to a
single order picker. This way the order picker can pick from other carousel(s) instead of waiting
while one of the carousels is rotating. In our animation the order picker is given a pick list, and

14 / 17
is responsible of picking from three carousels. The picker is able to initiate the rotation of each
of the carousels, and picks the items that are brought in front of him. When he is finished with
picking all the items in his list, he leaves his tote to a conveyor that will take it to the sorting
area.
Figure 5. Carousel
Order Picker Truck
An order picker truck enables the order picker to pick items from high level storage locations
(Figure 6). The normal operational mode in which the order picker truck uses in visiting pick
locations is the “nearest neighbor” mode, where the picker visits the next closest pick location at
each step. An alternative mode of operation is the “sweep” mode, where the order picker picks
all the items at a certain level before starting to pick the items in the next higher level. Our
animation simulates and time wise compares these two modes of operation.

15 / 17
Figure 6. Order Picker Truck Figure 7. Mobile Storage System
Mobile Storage System
A mobile storage system is used to store items that are requested very infrequently (Figure 7).
The main advantage of a mobile storage system is its space efficiency: There is only a single aisle
empty at any time. When the picker is to pick an item from the system, the system creates an
aisle dynamically to be able to make the pick. This system is typically used by media companies,
state institutions and hospitals to store archived documents.
Conclusions
We have presented our work towards creating and integrating web-compatible educational
media into warehousing education. Our work is unique since we have not found any other
similar work in the field of warehousing, except two web sites.

16 / 17
Possible future work in this topic involves development of other media for warehousing
education, including not only web based demonstrations/animations such as Java applets and
Flash animations, but also interactive 3D models of warehousing equipment, as in the work of
Ou et al. (2002). There is ongoing work going on at Sabanci University for developing such
educational materials.
One study that would contribute to the use of current media and further development of
educational materials in the future is measuring the usefulness of the developed media. This can
be done through formal surveys with users (senior and junior students at Sabanci University)
and analyzing the surveys thoroughly.
References
Bartholdi, J. J. and Eisenstein, D. (2006) Bucket Brigades; available under
http://www2.isye.gatech.edu/people/faculty/John_Bartholdi/bucket-brigades.html
Bartholdi, J. J. and Hackman, S. T. (forthcoming) Warehousing and Distribution Science; available
electronically under http://www.tli.gatech.edu/whscience/
Ettouney, H., El-Dessouky, H., Al-Fulaij, H. and Al-Ansary, A. (2000) Computer Package for
Design/Rating of Thermal Desalination Processes. Computer Applications in Engineering
Education, vol: 8, 80-103.
Frazelle, E. H. (2002) World-Class Warehusing and Material Handling. McGraw-Hill.
Horton, W. (2001) Leading E-Learning. American Society for Training and Development.
Leung W., Chen, Y. and Lee, Y. (2001) EM Wave Simulation: An Animated Electromagnetic Wave
Teaching Package. Computer Applications in Engineering Education, vol: 9, 208-219.
Ong, S. K. and Mannan, M. A. (2002) Development of an Interactive Multimedia Teaching Package for a
Course on Metalworking. Computer Applications in Engineering Education, vol: 10, 215-228.
Ou, S., Sung, W., Hsiao, S. and Fan, K. (2002) Interactive Web-Based Training Tool for CAD in a Virtual
Environment. Computer Applications in Engineering Education, vol: 10, 182-193.

17 / 17
Roodbergen, K. J. and De Koster, R. (2001) Routing methods for warehouses with multiple cross aisles.
International Journal of Production Research, vol: 39, no: 9, 1865-1883.
Simchi-Levi, D., Kaminsky, P. and Simchi-Levi, E. (2003) Designing and Managing the Supply Chain:
Concepts, Strategies, and Case Studies. McGraw-Hill/Irwin.

Demonstrating warehousing concepts through interactive animations

More Related Content

Similar to Demonstrating warehousing concepts through interactive animations (20)

More from Gurdal Ertek (20)

Recently uploaded (20)

Demonstrating warehousing concepts through interactive animations