Design and implementation of carrier based sinusoidal pwm (bipolar) inverter

International Journal of Science and Research (IJSR), India Online ISSN: 2319-7064
Volume 1 Issue 3, December 2012
www.ijsr.net
Design and Implementation of Carrier Based
Sinusoidal PWM (Bipolar) Inverter
1
Pankaj H Zope, 2
Pravin G.Bhangale , S. R.Suralkar3
1, 3
Department of Electronics & Telecommunication
SSBT COET, Bhambhori, Jalgaon, India
phzope@indiatimes.com
2
Departments of Electronics & Telecommunication
SSBT COET, Bhambhori, Jalgaon, India
pravinbhangale55@gmail.com
Abstract: SPWM or sinusoidal pulse width modulation is widely used in power electronics to digitize the power so that a sequence of
voltage pulses can be generated by the on and off of the power switches. The pulse width modulation inverter has been the main choice
in power electronic for decades, because of its circuit simplicity and rugged control scheme SPWM switching technique is commonly
used in industrial applications SPWM techniques are characterized by constant amplitude pulses with different duty cycle for each
period. The width of this pulses are modulated to obtain inverter output voltage control and to reduce its harmonic content. Sinusoidal
pulse width modulation or SPWM is the mostly used method in motor control and inverter application. In this development a unipolar
and bipolar SPWM voltage modulation type is selected because this method offers the advantage of effectively doubling the switching
frequency of the inverter voltage, thus making the output filter smaller, cheaper and easier to implement. Conventionally, to generate
this signal, triangle wave as a carrier signal is compared with the sinusoidal wave, whose frequency is the desired frequency. In this
paper single-phase inverters and their operating principles are analyzed in detail. The concept of sinusoidal Pulse Width Modulation
(PWM) for inverters is described with analyses extended to different kinds of SPWM strategies. Finally the simulation results for a
single-phase inverter (Bipolar) using the SPWM strategies described are presented [1],[2],[5].This project deals with implementing the
basic theory of a Sinusoidal Pulse Width Modulated Inverter (SPWM) technique for Bipolar voltage switching , its Simulink modelling,
estimating various designing parameters. The project will be commenced by a basic understanding of the circuitry of the SPWM
Inverter, the components used in its design and the reason for choosing such components in this circuitry. After this, it will be
attempted to simulate a model circuit on any simulating software e.g. MATLAB and analyse the output waveforms and also varying the
modulation index (M) for both Simulink Model and Implemented Design of Bipolar voltage switching
Keywords: Modulation, SPWM, Unipolar, Bipolar
1. Introduction
The dc-ac converter, also known as the inverter, converts dc
power to ac power at desired output voltage and frequency.
The dc power input to the inverter is obtained from an
existing power supply network or from a rotating alternator
through a rectifier or a battery, fuel cell, photovoltaic array
or magneto hydrodynamic generator. The filter capacitor
across the input terminals of the inverter provides a constant
dc link voltage. The inverter therefore is an adjustable-
frequency voltage source. The configuration of ac to dc
converter and dc to ac inverter is called a dc-link converter.
[2] Inverters can be broadly classified into two types, voltage
source and current source inverters. A voltage–fed inverter
(VFI) or more generally a voltage–source inverter (VSI) is
one in which the dc source has small or negligible
impedance. The voltage at the input terminals is constant. A
current–source inverter (CSI) is fed with adjustable current
from the dc source of high impedance that is from a constant
dc source [2], [1], [6].
A voltage source inverter employing thyristor as switches,
some type of forced commutation is required, while the
VSIs made up of using GTOs, power transistors, power
MOSFETs or IGBTs, self commutation with base or gate
drive signals for their controlled turn-on and turn-off. A
standard single-phase voltage or current source inverter can
be in the half-bridge or full-bridge configuration. The single-
phase units can be joined to have three-phase multiphase
topologies. Some industrial applications of inverters are for
adjustable-speed ac drives, induction heating, standby
aircraft power supplies, UPS (uninterruptible power
supplies) for computers, HVDC transmission lines, etc
[1],[8].
1.1 Inverters :
A device that converts DC power into AC power at desired
output voltage and frequency is called an Inverter. Phase
controlled converters when operated in the inverter mode are
called line commutated inverters. But line commutated
inverters require at the output terminals an existing AC
supply which is used for their commutation. This means that
line commutated inverters can’t function as isolated AC
voltage sources or as variable frequency generators with DC
power at the input. Therefore, voltage level, frequency and
waveform on the AC side of the line commutated inverters
can’t be changed. On the other hand, force commutated
inverters provide an independent AC output voltage of
adjustable voltage and adjustable frequency and have
therefore much wider application.
Inverters can be broadly classified into two types based on
their operation:
129

www.ijsr.net
 Voltage Source Inverters(VSI)
 Current Source Inverters(CSI)
Voltage Source Inverters is one in which the DC source has
small or negligible impedance. In Other words VSI has stiff
DC voltage source at its input terminals. A current source
inverter is fed with adjustable current from a DC source of
high impedance, i.e. from a stiff DC current source. In a CSI
fed with stiff current source, output current waves are not
affected by the load. From view point of connections of
semiconductor devices, inverters are classified as under [1],
[2]
 Bridge Inverters
 Series Inverters
 Parallel Inverter
Bridge Inverters are classified as Half bridge & Full bridge
Figure 1: Schematic of a Single Phase Full- Bridge Inverter
A single-phase inverter in the full bridge topology is as
shown in Fig. 1 which consists of four switching devices,
two of them on each leg. The full-bridge inverter can
produce an output power twice that of the half-bridge
inverter with the same input voltage. The S PWM switching
schemes are discussed in this section, which improve the
characteristics of the inverter. The objective is to add a zero
sequence voltage to the modulation signals in such a way to
ensure the clamping of the devices to either the positive or
negative dc rail; in the process of which the voltage gain is
improved, leading to an increased load fundamental voltage,
reduction in total current distortion and increased load power
factor. In Fig. 1, the top devices are assigned to be S11 and
S21 while the bottom devices as S12 and S22,
the voltage
equations for this converter are as given in the following
equations.[1],[6].
Vd (S11-S12) = Van + Vno= Vao …. (1)
2
Vd (S21-S22) = Vbn + Vno= Vbo ….. (2)
2
Vab = Van-Vbn … (3)
The voltages Van and Vbn are the output voltages from
phases A and B to an arbitrary point n, Vno is the neutral
voltage between point n and the mid-point of the DC source.
The switching function of the devices can be approximated
by the Fourier series to be equal to 1/2 * M.Where M is the
modulation signal which when compared with the triangular
waveform yields the switching pulses Thus from Equations1,
2, and 3 the expressions for the modulation signals are
obtained as
M 11 = 2(Van+Vno) .…. (4)
Vd
M 21 = 2(Van+Vno) ...... (5)
Vd
Equations 4 and 5 give the general expression for the
modulation signals for single-phase dc-ac converters. The
various types of modulation schemes presented in the
literature can be obtained from these equations using
appropriate definition for Van, Vbn & Vno[1]
2. SPWM Switching Techniques
PWM with Bipolar voltage switching
PWM with Unipolar voltage switching.
SPWM with Bipolar Switching:
The basic idea to produce PWM Bipolar voltage switching
signal is shown in Fig. 2. It comprises of a comparator used
to compare between the reference voltage waveform Vr with
the triangular carrier signal Vc and produces the bipolar
switching signal. If this scheme is applied to the full bridge
single phase inverter as shown in Fig., all the switch S11, S21,
S12 and S22 are turned on and off at the same time. The
output of leg A is equal and opposite to the output of leg B
[3]
The output voltage is determined by comparing the reference
signal, Vr and the triangular carrier signal, Vc and S12, S22
are turned on or turned off at the same time. The output of
leg A is equal and opposite to the output of leg B. The output
voltage is determined by comparing the control signal, Vr
and the triangular signal, Vc as shown in Fig. 5 to get the
switching pulses for the devices, and the switching pattern
and output waveform is as follows.[2]
Figure 2: Bipolar Generator
130

www.ijsr.net
Figure 3: SPWM with Bipolar voltage switching (a)
Comparison between reference Waveform and triangular
waveform (b) Gating pulses for S11 and S22 (c) Gating
pulses for S12 and S21 (d) Output waveform
2.2 SPWM with Unipolar Switching:
In this scheme, the triangular carrier waveform is
compared with two reference signals which are positive
and negative signal. The basic idea to produce SPWM
with unipolar voltage switching is shown in Fig. 4. The
different between the Bipolar SPWM generators is that the
generator uses another comparator to compare between
the inverse reference waveform−Vr. The process of
comparing these two signals to produce the unipolar
voltage switching signal. The switching pattern and output
waveform is as follows in Fig. 5. In Unipolar voltage
switching the output voltage switches between 0 and Vdc,
or switching event is halved in the unipolar case from
2Vdc to Vdc. The effective switching frequency is seen by
the load is doubled and the voltage pulse amplitude is
halved. Due to this, the harmonic content of the output
voltage waveform is reduced compared to bipolar
switching. In Unipolar voltage switching scheme also,
the amplitude of the significant harmonics and its
sidebands is much lower for all modulation indexes thus
making filtering easier, and with its size being
significantly smaller between 0 and −Vdc. This is in
contrast to the bipolar switching strategy in which the
output swings between Vdc and −Vdc. As a result, the
change in output voltage at each [2], [3], [4].
Figure 4: Unipolar PWM generator
Figure 5: Waveform for SPWM with Unipolar voltage
switching (a) Comparison between reference waveform and
triangular waveform (b) Gating pulses for S11 and S22 (c)
Gating pulses for S12 and S21 (d) Output waveform
3. Simulation and Implementation Results
Here we Design and Test Bipolar Voltage Switching for
Variable Modulation Index and also simulate in MATLAB
and see the switching pulses.
Simulink model and Waveforms:
Figure 6: Simulink Model Bipolar Voltage Switching
Figure 7: Simulink model for SPWN inverter
131

www.ijsr.net
Figure 8: Gating pulses for S1, S2, S3 and S4
4. Experimental kit and setup
Bipolar voltage switching inverter tested for different
modulating index with different resistive loads.
Figure 9: Experimental setup with resistive load bank
Figure.10 Switching gate pulses for Bipolar voltage
switching when M=0.5
Table.1 Experimental result of Bipolar voltage switching for
M=0.5
Figure.11 Switching gate pulses for Bipolar voltage
switching when M=0.9
Table.2 Experimental result of Bipolar voltage switching
for M=0.9
132

www.ijsr.net
5. Conclusion
In this paper the single phase SPWM microcontroller-
based 700VA inverter is designed and tested for Variable
modulation index (M=0.5- 1.1) For Bipolar voltage
switching. It gives a different result of currents and
voltages for different resistive loads wth Variable
modulation index and also note the gate pulse waveforms
for different modulation index. It was found that it gives
maximum efficiency for 100W load upto 92% for M=
0.7.and simulate this Bipolar switching model in
MATLAB,and note output waveform and gate pulses.
References
[1] B. Ismail, S.Taib MIEEE, A. R Mohd Saad, M. Isa,
C.M. Hadzer “Development of a Single Phase SPWM
Microcontroller-Based Inverter” First International
Power and Energy Coference PE Con 2006 November
28 -29, 2006, Putrajaya, Malaysia.
[2] Muhammad H. Rashid, "Power Electronics; Circuit's
Devices and Applications”, Third Edition, Prentice
Hall.2004.
[3] Nalin Kant Mohanty, Ranganath “Microcontroller
Based PWM Controlled Four Switch Three Phase
Inverter Fed Induction Motor Drive” SERBIAN
JOURNAL OF ELECTRICAL ENGINEERING Vol. 7,
No. 2, November 2010, 195-204.
[4] J. Kim, J. Hong, K. Nam “ A Current Distortion
Compensation Scheme For Four-switch Inverters”,
IEEE Transactions on Power Electronics, Vol. 24, No.
4, April 2009, pp. 1032 – 1040.
[5] C.T. Lin, C.W. Hung, C.W. Liu “Position Sensorless
Control for Four-switch Three-phase Brushless DC
Motor Drives”, IEEE Transactions on Power
Electronics, Vol. 23, No. 1, Jan. 2008, pp. 438 – 444.
[6] Mr. R.Senthilkumar, Prof. M.Singaaravelu “DESIGN
OF SINGLE PHASE INVERTER”, dsPIC30F4013
International Journal of Engineering Science and
Technology Vol. 2(11), 2010, 6500-6506
[7] Bose.K.B (1997) “Power Electronics and Variable
Frequency Drives”, IEE Press ISBN 0-7803-1061-
6,New York.
[8] Les Bowtell and Tony Ahfock “COMPARISON
BETWEEN UNIPOLAR AND BIPOLAR SINGLE
PHASE GRID CONNECTED INVERTERS FOR PV
APPLICATIONS “Faculty of Engineering Surveying,
University of Southern Queensland, Australia
(bowtelll@usq.edu.au)
[9] Borle L, Dymond M S, Nayar C V, Philips S J,
“Current Controlled Grid Connected Inverter”,
Proceedings of the Australian and New Zealand Solar
Energy Society Conference, pp 374-379, December
1993.
[10]Jim Doucet,Dan Eggleston,Jeremy Shaw, “DC/AC Pure
Sine Wave Inverter” MQP Terms ABC 20062007.
[11]Watt, Pure Sine Wave Inverter. Donrowe.com,
Retrieved December 14, 2006, From
http://www.donrowe.com/inverters/puresine_600.html
[12]ABS Alaskan. (2006). DC to AC Power Inverters,
Retrieved December 4, 2006, from
http://www.absak.com/basic/inverters.html.
[13]Bellis, Mary. William Stanley Jr. Retrieved December
16, 2006, from
http://inventors.about.com/library/inventors/blstanley
[14]BAHARUDDIN BIN ISMAIL, “Design And
Development Of Unipolar Spwm Switching Pulses For
Single Phase Full Bridge Inverter Application”,
UNIVERSITI SAINS MALAYSIA 2008
Authors
Pankaj H Zope has completed ME (DE) and presently working
in SSBT COET, Bhambhori, Jalgaon, India
Pravin G.Bhangale is a ME Student in SSBT COET,
Bhambhori Jalgaon, India
S. R.Suralkar has completed ME (DE) and is presently working
in SSBT COET, Bhambhori, Jalgaon, India
133

Design and implementation of carrier based sinusoidal pwm (bipolar) inverter

More Related Content

What's hot (19)

Similar to Design and implementation of carrier based sinusoidal pwm (bipolar) inverter (20)

More from International Journal of Science and Research (IJSR) (20)

Recently uploaded (20)

Design and implementation of carrier based sinusoidal pwm (bipolar) inverter