Effect of Transmission Parameters on PAPR of Universal Filter Multicarrier Modulation Systems_Crimson Publishers

Research & Development in Material Science
222
Res Dev Material Sci
222
Introduction
To support next generation wireless communication system
with higher data rates, less interference and lower PAPR a new
waveform candidate is required. Various new modulation schemes
like UFMC, FBMC, OFDM and GFDM have been introduced and
studied in different ways [1,2]. OFDM is one of the most popular
and accepted modulation techniques in many communication
systems. In OFDM, to increase robustness against Inter-Symbol
Interference (ISI) caused by multipath propagation on the radio
channel the total symbol duration is further increased by a
adding a Cyclic Prefix (CP). A CP is a copy of the tail of a symbol
placed at its beginning. However, the insertion of cyclic prefix
degrades its spectral efficiency and makes it less reliable for next
generation wireless communication. On the other hand, FBMC
improves spectral efficiency of system by using an inverse fast
Fourier transform/fast Fourier transform (IFFT/FFT) based filter
bank, and staggered OQAM (Orthogonal Quardrature Amplitude
Modulation) symbols, real symbols at twice the symbol rate of
FBMC/QAM, are loaded on the subcarriers. Hence, FBMC/OQAM
has a higher spectral efficiency but at the cost of increased system
complexity. UFMC seems to be attractive technique as it combines
the advantages of OFDM and FBMC [3]. It provides better sub carrier
separation like FBMC and less complexity like OFDM. Filter bank
multicarrier (FBMC) filters the signal on per subcarrier basis [4]
while orthogonal frequency division multiplexing (OFDM) filters
the signal on single shot [5]. UFMC (Universal filter multicarrier)
can be seen as a compromise between OFDM and FBMC, it groups
subcarriers to sub-bands, which are then filtered individually as
compared with single subcarrier or the complete band. In each sub
band, filter parameters and number of carrier per remains same
to prevents aliasing [6]. But all these multi carrier modulation
schemes suffer from the problem of higher peak to average power
ratio (PAPR). In this paper we have evaluated the effect of various
design parameters like filter length, FFT size, modulation order
and number of sub bands on the peak to average power ratio of
Universal filter multi carrier modulation technique.
The remainder of this paper is organized as follows: In section
II, the considered UFMC system model is presented. Section III
is devoted to the high Peak to average power ratio. In Section VI
reports simulation setup, including the performance evaluation
of UFMC in light of PAPR with different design factors. Finally,
conclusions are drawn in Section V.
UFMC System
UFMC system was developed based on the principle of
frequency division multiplexing (FDM) in which we divide the
input data stream into several lower rate sub-streams [7]. The
block diagram of a system employing UFMC is depicted in Figure
1 as shown in figure, the data stream is divided into sub-streams,
Pooja Rani, Silki Baghla and Himanshu Monga*
Department of ECE, JCDM College of Engineering, India
*Corresponding author: Himanshu Monga, Department of ECE, Director of JCDM College of Engineering, India
Submission: November 10, 2017; Published: January 17, 2018
Effect of Transmission Parameters on PAPR of
Universal Filter Multicarrier Modulation Systems
Copyright © All rights are reserved by Himanshu Monga.
Abstract
One of the main objectives of multicarrier modulation is to provide multiple accesses for wireless communication systems with higher data rates
whilehavingminimumoutofbandradiation,highspectralefficiencyandlesscomplexity.Orthogonalfrequencydivisionmultiplexing(OFDM),Universal
filter multicarrier (UFMC), Filter bank multicarrier (FBMC) and Generalized frequency division multiplexing (GFDM) modulation techniques have been
developed to support fourth generation and beyond 4G wireless systems. Demand of high data rate in fourth generation wireless communication
systems has been fulfilled by OFDM techniques but it suffers from the limitation of less spectral efficiency and high PAPR (Peak to average power ratio).
Thus to support next generation wireless systems other waveform models are getting attention. Among the techniques available, UFMC seems to be
attractive due to high spectral efficiency and less complexity. It has not explored much so in this paper, performance of UFMC have been evaluated with
different design factors such as number of sub bands, FFT (Fast Fourier Transform)size, filter characteristics and modulation under the light of PAPR.
Keywords: OFDM; GFD; UFMC; FBMC; FFT; PAPR
Mini Review
Research & Development in
Material ScienceC CRIMSON PUBLISHERS
Wings to the Research
ISSN: 2576-8840

How to cite this article: Pooja Rani, Silki Baghla, Himanshu Monga. Effect of Transmission Parameters on PAPR of Universal Filter Multicarrier Modulation
Systems. Res Dev Material Sci. 3(1). RDMS.000554. 2018. DOI: 10.31031/RDMS.2018.03.000554
223
Res Dev Material SciResearch & Development in Material Science
and then a pulse shaping filter with smooth edges is used on each
resource block in time domain that leads to substantial reduction in
out-of-band leakage in frequency domain. In this way, it minimizes
the harmful interference from adjacent sub channels of the
neighboring resource block [8].
Figure 1: UFMC system model.
As shown in Figure 1, the generated output can be given as:

1
RBN
i
p p k
p
x F V X
=
= ∑ (1)
Vp
, being of dimension
RR
SC SCN N× includes the relevant
columns of the inverse Fourier matrix according to the respective
sub-band position within the overall available frequency range, Fp
is a Toeplitz matrix with dimension ( 1)SC FilterN N N+ − × , composed
of the filter impulse response, enabling the convolution. The
signal can be rewritten without the summation by the following
definitions:
1 2 3[ , , ,....... ]RBNF F F F F= (2)
1 2 3( , , ,..... )RBp NV diag V V V V= (3)
,1 ,2 ,3 ,[ , , ,...... ]
T T T T
RB
i i i i i T
k k k k k NX X X X X= (4)
i
p kx FV X= (5)
The block-wise filtering provides flexibility to the system and
may be used to avoid the main FBMC drawbacks. UFMC supports
short bursts data transmission, as well as operation in fragmented
bands. The filter provides protection against inter-symbol
interference (ISI), as well as robustness for supporting multiple
access users which are not perfectly time-aligned. Due to the
possibility to reduce guard bands, and to avoid using a CP, UFMC
is spectrally more efficient than CP-OFDM. The receiver processing
can still be similar to CP-OFDM, single-tap per-subcarrier frequency
domain equalizers can be used which equalize the joint impact of
the radio channel and the respective sub band-filter [9]. This leads
to similar complexity order as CP-OFDM. So, it is thereby clear that
UFMC provides advantages of both OFDM and FBMC system [10].
Peak to Average Power Ratio
The PAPR is the relation between the maximum power of a
sample in a given transmit symbol divided by the average power
of that symbol. PAPR occurs when in a multicarrier system the
different sub-carriers are out of phase with each other [11]. At each
instant they are different with respect to each other at different
phase values. When all the points achieve the maximum value
simultaneously, this will cause the output envelope to suddenly
increase which causes a ‘peak’ in the output. There are a large
number of independently modulated subcarriers in multicarrier
system, and when they are added up coherently for transmission
purpose give a large peak value which is very large as compared to
average value of the sample. The ratio of the peak to average power
value is termed as Peak-to-Average Power Ratio and it can be given
as:
PAPR =
2
2
max{ [ ] }
{ [ ] }
x n
E x n
 
 
 
 
(6)
Where, is the amplitude of x[n] and E denote the expectation
of the signal.
PAPR in dB can be written as:
PAPR (dB) = 10log10
(PAPR) (7)
This higher PAPR causes saturation in power amplifier which
produces inter modulation products among sub bands and also
increases out of band radiation [12].
Different Factors Effecting PAPR in UFMC
There are various parameters which can effect UFMC signal
generation [13]. In this section we have given a brief of all these
design parameters, which we should take in account while
designing an UFMC system model.
Filter characteristics
For the choice of the filter characteristics many alternatives are
available. In this experimental work we have used Dolph-chebyshev
filter and evaluated effect of different filter lengths on PAPR of
UFMC. For a given type of sub band filter, the filter length is a key
parameter affecting the system performance in different ways. A
longer filter not only leads to lower out of band emission, but also
results in better frequency localization, and makes the system more
robust to synchronization errors and multipath fading channels.
However, a longer filter also causes several drawbacks including
more frequency selective filter response along subcarriers within
one sub band and larger overhead, reducing transmission efficiency
in the time domain [14].

Research & Development in Material Science
224
Res Dev Material Sci
Modulation type and its orders
There are various modulation schemes which can be use
for UFMC system model such as BPSK, QAM, and QPSK. For this
evaluation we have used QAM modulation and studied effect of
different modulation orders such as 4QAM, 16QAM, 64QAM and
256QAM. Modulation order of the system plays an important role
on system performance and its PAPR value also get affected by this
[15,16].
FFT size
The third factor taken in account is FFT size of the transmitter.
We have evaluated PAPR of UFMC by varying FFT size. For example:
256-point FFT, 512-point FFT, 1024-point FFT and 2048-point FFT
[16].
Number of sub bands
The sub band size is also having a great impact on signal
generation of UFMC model. Number of sub bands, FFT size,
modulation order and filter length are those key factors which
can change signal generation in a large way. In this paper we are
evaluating impact of these factors on system performance.
Simulation Setup
In this section we have evaluated that how different design
factors of UFMC model affects its PAPR value. Different design
parameters for simulation setup are summarized in Table 1.
Table 1: Simulation parameters for considered UFMC
system.
Parameter Value
Filter Characteristics
Dolph-chebyshev filter with filter
length- 43, 63, 83
Modulation Order QAM- 4,64,256
FFT Size FFT point- 256, 512, 1024, 2048
Number of sub bands 20, 30, 40
Table 2: PAPR values with different filter length.
Number of
Sub Bands
Filter
Length
Modulation
Order
FFT Size PAPR
20 43 256 512 22.9060
20 63 256 512 21.8020
20 83 256 512 20.2872
Table 2 gives different values of filter length and the
corresponding values of PAPR are also given. Figure 2 is showing
the effect of different filter length on PAPR of system, here we are
using Dolph-chebyshev filter for realization of the system. It is clear
from table and figure that as we increase the filter length it reduces
the PAPR and vice-versa.
Figure 2: Effect of filter length on PAPR of UFMC.
We can say that a higher filter length can achieve a better PAPR
performance but it also makes the filter more frequency selective
which in turn reduces it bandwidth. Table 3 is showing different
values of PAPR with change in modulation order of the system and
corresponding values are shown graphically in Figure 3. From this
it is clear that UFMC is having minimum value of PAPR at moderate
modulation order and peak to average power ratio is higher at
both low and high modulation orders, it keeps on increasing as the
modulation order is increased. The next factor of our observation is
that how FFT size of the transmitter affects the PAPR of the system.
Table 4 is showing values of PAPR corresponding to the FFT size of
the transmitter and Graphical representation is given in Figure 4.
Table 3: PAPR values with different modulation orders.
Number of
Sub Bands
Filter
Length
Modulation
Order
FFT size PAPR
20 43 4 512 21.7315
20 43 64 512 20.7673
20 43 256 512 22.9060
Table 4: PAPR values with different FFT size.
Number of
Sub Bands
Filter
Length
FFT Size
Modulation
Order
PAPR
20 83 256 256 17.8552
20 83 512 256 20.2872
20 83 1024 256 21.8360
20 83 2048 256 20.2337

225
Res Dev Material SciResearch & Development in Material Science
Figure 3: Effect of modulation order on PAPR of UFMC.
Figure 4: Effect of FFT Size on PAPR of UFMC.
From this Figure 5 & Table 5 it is clear that a moderate value of
FFT produces a higher value of PAPR and higher as well as lower
values of FFT Size are resulting in lower PAPR value. The last factor
which is included in this evaluation is number of sub bands used
in system design. Following table and graph shows the effect of
number of sub bands on PAPR of UFMC. From this, it is clear that
by using large number of sub bands we can reduce PAPR to a great
extent.
Figure 5: Effect of Number of Sub bands on PAPR of UFMC.
Conclusion
In this paper we have studied that how different design factors
of an UFMC model can affect its performance because a higher PAPR
value put a great impact on system performance and degrades it.
So, depending on these experimental outcomes we can design such
an UFMC model which give lower value of PAPR. This evaluation
also shows that although UFMC modulation is having advantages of
both FBMC and OFDM but it is having limitation of higher peak to
averagepowerratiolikeothertwomodulationschemes.So,infuture
we can focus on some PAPR reduction techniques to overcome this
shortcoming of the UFMC modulation to make it more reliable and
efficient for next generation wireless communication.
References
1. Rohde, Schwarz (2016) Application Note “5G waveform candidates”.
2. 5GNOW (2013) D3.1: 5G waveform candidate selection. Tech Rep.
3. Schaich F, Wild T (2014) Waveform contenders for 5G-OFDM vs. FBMC
vs. UFMC. ISCCSP pp. 457-460.
4. Farhang-Boroujeny B (2011) OFDM versus filter bank multicarrier.
IEEE Signal Process Mag 28(3): 92-112.
5. Bingham John (1990) Multi carrier modulation for data transmission:
An idea whose time has come. IEEE Commun Mag 28(5): 5-14.
6. Vakilian V, Wild T, Schaich F, Ten Brink S, Frigon JF (2013) Universal-
filtered multi-carrier technique for wireless systems beyond LTE. IEEE
Globecom Workshops pp. 223-228.
7. Wunder G, Jung P, Kasparick M, Wild T, Schaich F, et al. (2014)
5GNOW: non-orthogonal, asynchronous waveforms for future mobile
applications. IEEE Commun Mag 52(2): 97-105.
8. Chen Y, Schaich F, Wild T (2014) Multiple access and waveforms for 5G:
IDMA and universal filtered multi-carrier. IEEE 79th
VTC Spring pp. 1-5.
9. Wild T, Schaich F, Chen Y (2014) 5G Air interface design based on
universal filtered (UF-)OFDM. 19th
International Conference on Digital
Signal Processing pp. 699-704.
10. An C, Kim B, Ryu HG (2016) Waveform comparison and nonlinearity
sensitivities of FBMC, UFMC and W-OFDM systems. 8th
International
Conference on Networks & Communications, pp. 83- 90.
11. Gangwar A, Bhardwaj M (2012) An overview: peak to average power
ratio in OFDM system &its Effect. IJCOTS 1(2): 22-25.
12. Tellado J, Cioffi JM (1999) PAR reduction in multicarrier transmission
system. Stanford University, USA.
13. Zhang L, Ijaz A, Xiao P, Ali Imran M, Tafazolli R (2016) MU-UFMC system
performance analysis and optimal filter length and zero padding length
design.
14. Elmaroud B, Faqihi A, Abbad M, Aboutajdine D (2014) On the impact
of prototype filter length on the PAPR reduction of FBMC signals. IJET
6(4): 1951-1960.
15. Chandra G, Dinesh KS, Anuj S (2013) Examine the impact of modulation
order and sub-bands on PAPR reduction techniques using various
modulator in 802.11a/b/g. International Journal of Computer
Applications (0975 - 8887) 69(6): 49-56.
16. Abdullah MFL, Ghanim MF, Yonis AZ (2013) Effects of FFT size on
PAPR of MC-CDMA system. IEEE 9th
International Colloquium on Signal
Processing and its Applications.

Effect of Transmission Parameters on PAPR of Universal Filter Multicarrier Modulation Systems_Crimson Publishers

More Related Content

What's hot (20)

Similar to Effect of Transmission Parameters on PAPR of Universal Filter Multicarrier Modulation Systems_Crimson Publishers (20)

More from CrimsonPublishersRDMS (20)

Recently uploaded (20)

Effect of Transmission Parameters on PAPR of Universal Filter Multicarrier Modulation Systems_Crimson Publishers