Effect of use of recycled materials on indirect tensile

IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
__________________________________________________________________________________________
IC-RICE Conference Issue | Nov-2013, Available @ http://www.ijret.org 226
EFFECT OF USE OF RECYCLED MATERIALS ON INDIRECT TENSILE
STRENGTH OF ASPHALT CONCRETE MIXES
Shunyashree1
, Tejas Bhavimane2
, M.R.Archana3
, M S Amarnath4
1, 2
IV 1
semester, M.Tech, 3
Assistant Professor, 4
Professor-Civil Engineering, R.V College of Engineering, Bangalore,
India
shunyashree@gmail.com, tejasbavimane@ymail.com, archana.mosale@gmail.com, amarnath_ms@rediffmail.com
Abstract
Depletion of natural resources and aggregate quarries for the road construction is a serious problem to procure materials. Hence
recycling or reuse of material is beneficial. On emphasizing development in sustainable construction in the present era, recycling of
asphalt pavements is one of the effective and proven rehabilitation processes. For the laboratory investigations reclaimed asphalt
pavement (RAP) from NH-4 and crumb rubber modified binder (CRMB-55) was used. Foundry waste was used as a replacement to
conventional filler. Laboratory tests were conducted on asphalt concrete mixes with 30, 40, 50, and 60 percent replacement with RAP.
These test results were compared with conventional mixes and asphalt concrete mixes with complete binder extracted RAP
aggregates. Mix design was carried out by Marshall Method. The Marshall Tests indicated highest stability values for asphalt
concrete (AC) mixes with 60% RAP. The optimum binder content (OBC) decreased with increased in RAP in AC mixes. The Indirect
Tensile Strength (ITS) for AC mixes with RAP also was found to be higher when compared to conventional AC mixes at 300
C.
Keywords: Reclaimed asphalt pavement, Foundry waste, Recycling, Marshall Stability, Indirect tensile strength.
--------------------------------------------------------------------***-----------------------------------------------------------------------
1. INTRODUCTION
Recycling has been successfully used at many places world
over and has shown good performances. Asphalt pavement
recycling technology is not so popular in India, but gaining its
popularity because of its valuable approach for technical,
environmental and economical reasons. By volume, aggregate
generally accounts for 92 to 96 percent of AC and about 70 to
80 percent of Portland cement concrete. Aggregate is also used
for base and sub-base courses for both flexible and rigid
pavements. Aggregates can either be natural or manufactured.
Natural aggregates are generally extracted from larger rock
formations through an open excavation. While several factors
influence the use of RAP in asphalt pavement, the two primary
factors are economic savings and environmental benefits. RAP
is a useful alternative to virgin materials because it reduces the
use of virgin aggregate and the amount of virgin asphalt binder
required in the production of hot mix asphalt. The use of RAP
also conserves energy, lowers transportation costs required to
obtain quality virgin aggregate, and preserves resources.
Additionally, using RAP decreases the amount of construction
debris placed into landfills and does not deplete non renewable
natural resources such as virgin aggregate and asphalt binder.
2. LITERATURE REVIEW
Recycling asphalt creates a cycle that optimizes the use of
natural resources and sustains the asphalt pavement industry.
Based on the recent studies, in USA, 33 million tons of RAP is
used per year for recycling purpose which is around 80% of
the total amount of RAP collected from old bituminous
pavements. The amount of RAP used for recycling per year is
about 0.84 million tons in Sweden, 7.3 million tons in
Germany, 0.53 million tons in Denmark and around 0.12
million tons in Netherlands. Pavement recycling-an overview:
This discusses about the various recycling materials and they
also study the advantages of RAP over other recycling
material. Which includes, According to a report published by
the Federal Highway Administration (1997), in the United
States of America, asphalt pavement is the most recycled
product (in terms of tonnage) compared to others such as
newsprint, glass bottles, aluminum cans and plastic containers.
The conclusion is as follows, as resources become scarcer and
environmental concern becomes more widespread, it is
anticipated that pavement recycling will become more
important in the coming years. Use and Reuse of materials
have gained high importance in recent years. Depleting natural
resources, reuse of available resources can effectively cut
down cost and save environment. The literature review
indicates that not many studies are on use of reclaimed asphalt
pavement in bituminous mixes have been tried hence
necessitating the study.
2.1 Need for Study
The main emphasis of this study was to reuse the high
invested pavement material for its best instead of burying it in
underneath layers over the new pavement. Depleting natural
resources and increase in cost gives way to use of RAP for the

__________________________________________________________________________________________
pavement. Reuse of available resources can effectively cut
down cost and save environment. Though use of RAP in base
and sub base courses have been explode, full fledged use is yet
to be undertaken under field conditions. Also, use of RAP in
binder courses is less explored. In this work an effort has been
taken up to throw light on use of RAP in bituminous concrete
grade I mixes with laboratory investigations.
2.2 Objectives of Present Paper
1. To evaluate the improvement or changes in Marshall
properties namely stability, flow, bulk density, voids in
mineral aggregates (VMA), voids filled with bitumen
(VFB), optimum binder content for AC mixes with
varying percentage of RAP.
2. To compare the Marshall properties of AC mixes with
RAP and AC mixes with conventional aggregates and
bitumen or binder extracted aggregates.
3. To study the indirect tensile strength behaviour of
asphalt concrete mixes with conventional aggregate,
binder extracted aggregates and varying percentages of
Rap at 30o
C.
3. METHODOLOGY
For the present study RAP has been procured from the surface
course BC grade I of NH-4 from Sira near Tumkur. Black
sand a by-product from the foundry industry has been used as
filler in AC mix. Crumb rubber modified bitumen (CRMB-55)
has been used as the binder material since the procured RAP
contained the CRMB-55 binder. For the present study, an
attempt has been made to investigate the effect of RAP in
asphalt concrete.RAP without binder extraction has been tried
at trial percentages of 30, 40, 50, and 60. For comparison,
laboratory properties of AC mixes with conventional
aggregate was tried. Also an attempt has been made to use
binder extracted RAP aggregate in AC mixes. In all the cases,
foundry waste has been used as replacement to conventional
fine aggregates and filler.
Coarse aggregates: Conventional aggregate were collected
from local quarry. These were replaced with 30, 40, 50 and 60
percentage of RAP. Hence basic properties of both
conventional and RAP were conducted and are as presented in
Table1.
Fine aggregates: Foundry waste has been used as fine
aggregate in extracted RAP AC mixes for the size 300 and 150
microns, For 30, 40, 50, 60, percentages of RAP AC mixes
2.36 mm and 1.18 mm RAP fines are used. Conventional
aggregates are used for missing blending proportions of RAP.
For binder extracted RAP aggregates foundry waste are used
as substitute for fine aggregate.
Table 1 Basic properties of conventional and RAP aggregates
Sl no Aggregate tests
Conventional
aggregates
RAP
aggregates
Requirements as per Table 500-14 of
MoRT&H
(IV revision)
Specifications
1 Crushing value (%) 22.7 21.1 Max 30%
2 Impact value (%) 19 16.08 Max 27%
3 Los Angeles abrasion value (%) 21.50 20 Max 35%
4
Flakiness and Elongation Index
(Combined) (%)
29.52 26 Max 30%
5 Water absorption (%) 0.162 0.11 Max 2%
6
Aggregate specific gravity
1.Coarse aggregate
2.Fine aggregate
2.65
2.7
2.69
2.31
2.5-3.0
Filler: The foundry collected is a byproduct which is used as a
raw material for cement industry. Fills the voids between the
fine aggregates, stiffens the binder and offers permeability.
Black sand byproduct of foundry industry was used as filler in
asphalt mix. The foundry waste was collected from Dakshin
industry near Hoskote, Bangalore. The chemical composition
of foundry waste is as shown in table 2. The percentage of
silica being 89.49% encouraged the use of foundry waste as
fine aggregates and filler as a replacement to conventional
aggregate and cement respectively. Specific gravity of foundry
waste was found to be 2.56.

__________________________________________________________________________________________
Table 2 Chemical composition of Foundry waste
Source: Raghavendra Spectro Metallurgical Laboratory, Bangalore.
Binder: Fills the voids and also cause particle adhesion.
Crumb rubber modified bitumen (CRMB-55) is used in the
mix as the procured RAP contained the same binder in the
aggregates which was used without extraction.
Table 3 Basic properties of Crumb rubber modified bitumen (CRMB-55)
Sl.No Parameter Value (%)
1 Calcium Carbonate 0.60
2 Magnesium Carbonate 0.10
3 Silica 89.49
4 Titanium di Oxide 0.68
5 Alumina 2.40
6 Manganese Oxide 0.03
7 Magnesium Oxide 0.03
8 Calcium Oxide 0.34
9 Potassium Oxide 2.60
10 Phosphorus Pentoxide 0.01
11 Barium Oxide 0.03
12 Loss of Ignition 3.68
SL
No.
Test Conducted Test results
Requirements as per
IRC SP:53-2002
1 Penetration at 250
C,0.1 mm, 100gm, 5sec 56 <60
2 Softening point (R&B), (0
C) 56 55(minimum)
3 Flash point,0
C 310 220 (minimum)
4
Elastic Recovery of half thread in ductilometer at
150
C, %,
60 50 (minimum)
Thin film oven test (TFTO) on residue
5 Penetration at 250
C,0.1 mm, 100gm, 5sec 64 60(minimum)
6 Increase in softening point (R&B), (0
C), 5 6(maximum)
7
Elastic Recovery of half thread in ductilometer at
250
C, %
45 35(minimum)

__________________________________________________________________________________________
Aggregate gradation: Bituminous concrete mix of grading-I,
was chosen as per clause 500-18, of MoRT&H (IV revision)
specifications. Table 4 shows the gradation adopted for the
mix.
Table 4 Aggregate gradation as per MoRT&H (IV revision) for Asphalt concrete grade-I mix
Sieve size in, mm Adopted mid gradation
% Weight
Retained
Weight retained,
grams
26.5 – 19 89.5 10.5 129
19 - 13.2 69 20.5 247
13.2 - 9.5 62 7 88
9.5 - 4.75 45 17 205
4.75 - 2.36 36 9 111
2.36 - 1.18 27 9 111
1.18 - 0.6 21 6 76
0.6 - 0.3 15 6 80
0.3 - 0.15 9 6 76
0.15 - 0.75 5 4 53
4. MARSHALL METHOD OF MIX DESIGN
Marshall Tests were conducted for asphalt concrete mixes
prepared with replacement of conventional coarse and fine
aggregate with RAP and filler with foundry waste with trial
percentages of 30, 40, 50, and 60. For comparison Marshall
tests were conducted on asphalt concrete mixes with binder
extracted RAP aggregate and conventional aggregates.
CRMB-55 was used as binder since the source of RAP
contained the same binder. Foundry waste was used to replace
the conventional fine aggregate and filler. The Marshall test
results for AC mixes with conventional and bitumen extracted
RAP aggregates are as shown in Table 5. Marshall Test was
conducted in accordance with code ASTM D6926 – 04. Figure
1 to Figure 3 indicates the influence of Marshall properties of
RAP on asphalt concrete mixes.
Table.5 Marshall Properties of asphalt concrete mix with conventional aggregates and Bitumen extracted RAP aggregates
Sl.No AC mix with Marshall
stability, KN
Flow,
mm
VMA,% VFB,% OBC,
%
Bulk density,
gm/cc
1
Conventional
aggregates
25.9 3.87 13.6 88.94 5.3 2.3
2
Bitumen
extracted
aggregates
27.11 3.81 13.60 87.57 5.2 2.29

__________________________________________________________________________________________
Fig1. Effect of RAP on Marshall Stability and flow of asphalt concrete mixes
Fig 2.Effect of RAP on VMA and VFB of asphalt concrete mixes
Fig3 Effect of RAP on OBC and bulk density of asphalt concrete mixes

__________________________________________________________________________________________
4.1 Indirect Tensile Strength Test
Indirect tensile strength tests were conducted on asphalt
concrete mixes at optimum binder content for 30, 40, 50, 60
percentages of RAP aggregates. For comparison asphalt
concrete mixes prepared with conventional aggregates and
binder extracted RAP aggregates were tested for indirect
tensile strength. The tests were conducted on unconditioned
specimens at 30oC.
The indirect tensile test is performed by loading a cylindrical
specimen with a single or repeated compressive load
according to ASTM D 6931 test, which acts parallel to and
along the vertical diametric plane. This loading configuration
develops a relatively uniform tensile stress perpendicular to
the direction of the applied load and along the vertical
diametric plane, which ultimately causes the specimen to fail
by splitting along the vertical diameter.
4.2 Indirect Tensile Strength Test Results
The tests were conducted on the asphalt concrete mixes
prepared for both conventional and RAP specimens with 30,
40, 50, 60 percent without extraction, 100 percent RAP with
extraction with test temperature of 300C. Table 6 and 7 shows
the indirect tensile strength test results and the same is
graphically represented as shown in figure4.
Table.6 Effect of RAP on ITS of AC mixes at 300
C.
Table7 Indirect tensile strength test results for 0, 100 percent
extracted RAP aggregates at 300
C.
Fig4. Effect of RAP on indirect tensile strength in AC mixes
DISCUSSIONS AND CONCLUSIONS
Marshall Stability and indirect tensile strength test were
conducted on asphalt concrete mixes with 30, 40, 50, and 60%
RAP aggregate. For comparison, tests were also conducted on
asphalt concrete mixes with conventional and bitumen
extracted aggregate. From table 5 and figure 1 to figure 3
following inferences was withdrawn.
1. The Marshall Stability and bulk density of AC mixes
initially decreased and further increased with the increase
in RAP aggregates. Stability value obtained satisfied the
requirements as per Table 500-19, MoRT&H (IV
revision).
2. The flows increased with increase in RAP content and
were in the permissible limit as per Table 500-19,
MoRT&H (IV revision). But the AC mix with 60% RAP
showed the maximum flow which was more than the
permissible limits.
3. Percentage of voids in mineral aggregates and optimum
binder content decreased with the increase of RAP
aggregates in AC mixes.
4. Percentage of voids filled with bitumen increased and
decreased as the RAP contentment was increased. This
was not in permissible limits as per Table 500-19,
MoRT&H (IV revision) due to the presence of bitumen
content of RAP.
5. The stability of AC mixes was found to be increased by
28.6%, 26.29%, 13.16%, 46.6% and 4.67% for 30, 40,
50, 60% and bitumen extracted aggregates as compared
to conventional mixes. Due to the presence of hard aged
binder the stability has increased when compared with
conventional mix.
6. It was found that optimum binder content decreased by
14.5%, 21.5%, 23.9%, 24.5% and 1.8% for 30, 40, 50,
60% and bitumen extracted aggregates as compared to
conventional mixes. The presence of bitumen content in
the RAP has influenced the optimum binder content to
decrease with respect to conventional mix.

__________________________________________________________________________________________
7. Flow was found to be increased by 9.7%, 39.5%, 18.98%
for 40, 60% RAP content and binder extracted RAP
aggregates. Whereas 41.04% and 21.76% has decreased
for 30 and 50% of RAP aggregate when compared with
conventional AC mixes.
8. Bulk density of asphalt concrete mixes was found to be
almost equal when compared with conventional mix and
binder extracted RAP aggregates.
9. Indirect Tensile Strength of asphalt concrete mixes was
found to be increased by 52.73%, 38.09%, 28.64%,
30.97% for 30, 40, 50 and 60%. Whereas decreased by
6.12% for binder extracted RAP aggregates when
compared with conventional AC mixes.
REFERENCES
[1] Freddy L. Roberts, Prithvi S. Khandal, E .Ray Brown,
“Hot mix asphalt materials, mixture design and
construction” NAPA, Maryland, II Edition, 1996.
[2] Audrey Copeland, “Reclaimed Asphalt Pavement in
Asphalt Mixtures: State of the Practice”, FHWA-HRT-
11-021, April 2011
[3] National Cooperative Highway Research Program,
synthesis 421, “Recycling and reclaimation of asphalt
pavemen”t, Transportation research board, 2011.
[4] Ken Sweeden, “Utilization of Reclaimed asphalt
pavement” North Dakota Asphalt conference april 7,
2010
[5] Basic Asphalt Recycling Manual, ARRA- Asphalt
Recycling and Reclaiming Association, U S
Department of Transportation,2001.
[6] Ministry of Road Transport and Highways
(MoRT&H).Specification for Roads and Bridge work.
Government of India, Indian Roads Congress, 4th
revision, New Delhi, India,2001.
[7] Laureano R. Hoyos,; Anand J. Puppala,; and Carlos A.
Ordonez, “Characterization of Cement-Fiber-Treated
Reclaimed Asphalt Pavement Aggregates: Preliminary
Investigation” journal of materials in civil engineering
© ASCE ,977-989, july 2011.
[8] Anand J. Puppala,; Sireesh Saride,; and Richard
Williammee “Sustainable Reuse of Limestone Quarry
Fines and RAP in Pavement Base/Subbase Layers”
Journal of materials in civil engineering © ASCE ,418-
429, april 2012.

Effect of use of recycled materials on indirect tensile

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Effect of use of recycled materials on indirect tensile (20)

More from eSAT Publishing House (20)

Recently uploaded (20)

Effect of use of recycled materials on indirect tensile