Edwards Signaling EG1F-C Installation Manual
0 likes185 views
The Genesis Chime is an indoor audible fire alarm notification device with configurable options for sound output and operation modes. It requires a Genesis Signal Master for coded operation and must be installed following NFPA codes and local regulations. The document includes information on model numbers, electrical specifications, installation instructions, and maintenance requirements.
![2 / 2 27MAY03 P/N: 3100561 REV: 1.0
Table 2: Operating current in (Amp RMS)
High db Low db
16 Vdc 0.030 0.019
24 Vdc 0.043 0.026
33 Vdc 0.045 0.027
16 Vfwr 0.060 0.040
24 Vfwr 0.076 0.049
33 Vfwr 0.081 0.055
Vdc = Volts direct current, regulated and filtered
Vfwr = Volts full wave rectified.
Table 3: Sound level output (dBA)
Signal and voltage High db Low db
16 Vdc 56.9 52.5
24 Vdc 59.8 54.8
Temporal
33 Vdc 60.1 55.0
16 Vdc 58.2 52.8
24 Vdc 60.8 55.6
Steady
33 Vdc 61.3 56.1
dBA = Decibels, A-weighted
UL464: Sound level output at 10 ft (3.05 m) measured in a
reverberant room.
Installation instructions
Caution: Electrical supervision requires the wire run to be
broken at each terminal. Do not loop the signaling circuit field
wires around the terminals.
To install the chime:
1. Remove the cover by depressing both tabs on the top of
the unit with a small screwdriver and twisting slightly.
2. Set the chime signal, sound output level, and desired
operation settings. See Figure 1.
3. Connect the chime terminals to the signal circuit field
wiring. You must observe polarity for the unit to function
properly.
For constant non-coded voltage operation, see Figure 2.
For single-stroke coded voltage operation, see Figure 3.
4. Mount the unit onto a compatible electrical box, making
sure not to over tighten the mounting screws.
5. Replace the cover by aligning at the bottom, then
snapping in at the top.
6. Test the unit for proper operation.
Maintenance
This unit is not serviceable or repairable. Should the unit fail to
operate, contact the supplier for replacement.
Perform a visual inspection and an operational test twice a
year or as directed by the local authority having jurisdiction.
J2 J3J1
To change the chime
from steady to temporal cut
from circle J1 to edge of
circuit board
signal
To change the chime
from non-coded to coded (single-
stroke)
operation
cut from circle J2 to edge
of circuit board
To change the chime
from high dB to
low dB cut J3 trace between
holes
sound
output level
Figure 1: Chime settings
Note: Polarity shown in alarm condition
To next device or
end of line device
-
+
-
+
From compatible fire
alarm control panel
+
-
+
-
Figure 2: Constant non-coded voltage operation
Genesis device with
Genesis Signal Master
[1]
-
+
HS
-
+
To next device or
end of line device
Continuous
power source
Coded power
source
+
+
-
-
+
-
Figure 3: Single-stroke coded voltage operation](https://image.slidesharecdn.com/eg1f-c-150526143222-lva1-app6892/85/Edwards-Signaling-EG1F-C-Installation-Manual-2-320.jpg)
Edwards Signaling EG1F-C Installation Manual
- 1. Installation Sheet 27MAY03 P/N: 3100561 REV: 1.0 Genesis Chime 1 / 2 Genesis Chime Product information The Genesis Chime is an audible fire alarm notification appliance designed for indoor walls. See Table 1 for a list of model numbers. The chime includes field configurable jumper options for selecting the desired dB output, steady or temporal chime output, and constant non-coded voltage or single-stroke coded voltage operation. A Genesis Signal Master is required when chimes are configured for coded operation. See Table 2 for a list of compatible synchronization modules. Install this device in accordance with applicable requirements in the latest editions of the NFPA codes and standards and in accordance with the local authorities having jurisdiction. Table 1: Model numbers Model description Model numbers Chime, white ADTG1-C MG1-C EG1-C XLSG1-C G1-C ZG1-C G1-C-LG Chime, white, with FIRE marking ADTG1F-C MG1F-C EG1F-C XLSG1F-C G1F-C ZG1F-C G1F-C-LG Chime, red ADTG1R-C MG1R-C EG1R-C XLSG1R-C G1R-C ZG1R-C G1R-C-LG Chime, red, with FIRE marking ADTG1RF-C MG1RF-C EG1RF-C XLSG1RF-C G1RF-C ZG1RF-C G1RF-C-LG Trim plate, white ADTG1T MG1T EG1T XLSG1T G1T ZG1T G1T-LG Table 1: Model numbers Model description Model numbers Trim plate, red ADTG1RT MG1RT EG1RT XLSG1RT G1RT ZG1RT G1RT-LG Table 2: Compatible synchronization modules Model names Model numbers Auto-Sync Output Module SIGA-CC1S SIGA-MCC1S SIGA-CC1S-LG SIGA-MCC1S-LG Signal Master snap-on piggyback (1-gang) ADTG1M MG1M EG1M XLSG1M G1M ZG1M G1M-LG Signal Master - Remote Mount ADTG1M-RM MG1M-RM EG1M-RM XLSG1M-RM G1M-RM ZG1M-RM G1M-RM-LG Note: Synchronization module requirements are determined by your application Specifications Operating voltage Regulated 16 to 33 Vdc, 16 to 33 Vfwr This device was tested to the regulated 24 Vdc/fwr operating voltage limits of 16 V and 33 V. Do not apply 80% and 110% of these values for system operation. Operating current: See Table 2 Sound level output: See Table 3 Signals Steady: 60 strokes per minute Temporal: 3-stroke pattern Coded: Maximum 60 strokes per minute Operating modes Non-coded: Continuous voltage Coded: Single-stroke controlled by voltage Default settings Signal: Steady Sound level output: High db Operation: Non-coded Wire size: 12 to 18 AWG (2.50 to 0.75 sq mm) Compatible electrical boxes North American 2-1/2 in (64 mm) deep 1-gang box Standard 4 in square box 1-1/2 in (38 mm), 2-gang, or 4 in octagonal with G1T or G1RT trim accessory Operating temperature range: 32 to 120 °F (0 to 49 °C) Operating humidity range: 0 to 93% RH Agency listings: Meets or exceeds UL464 Seventh Edition for private mode
- 2. 2 / 2 27MAY03 P/N: 3100561 REV: 1.0 Table 2: Operating current in (Amp RMS) High db Low db 16 Vdc 0.030 0.019 24 Vdc 0.043 0.026 33 Vdc 0.045 0.027 16 Vfwr 0.060 0.040 24 Vfwr 0.076 0.049 33 Vfwr 0.081 0.055 Vdc = Volts direct current, regulated and filtered Vfwr = Volts full wave rectified. Table 3: Sound level output (dBA) Signal and voltage High db Low db 16 Vdc 56.9 52.5 24 Vdc 59.8 54.8 Temporal 33 Vdc 60.1 55.0 16 Vdc 58.2 52.8 24 Vdc 60.8 55.6 Steady 33 Vdc 61.3 56.1 dBA = Decibels, A-weighted UL464: Sound level output at 10 ft (3.05 m) measured in a reverberant room. Installation instructions Caution: Electrical supervision requires the wire run to be broken at each terminal. Do not loop the signaling circuit field wires around the terminals. To install the chime: 1. Remove the cover by depressing both tabs on the top of the unit with a small screwdriver and twisting slightly. 2. Set the chime signal, sound output level, and desired operation settings. See Figure 1. 3. Connect the chime terminals to the signal circuit field wiring. You must observe polarity for the unit to function properly. For constant non-coded voltage operation, see Figure 2. For single-stroke coded voltage operation, see Figure 3. 4. Mount the unit onto a compatible electrical box, making sure not to over tighten the mounting screws. 5. Replace the cover by aligning at the bottom, then snapping in at the top. 6. Test the unit for proper operation. Maintenance This unit is not serviceable or repairable. Should the unit fail to operate, contact the supplier for replacement. Perform a visual inspection and an operational test twice a year or as directed by the local authority having jurisdiction. J2 J3J1 To change the chime from steady to temporal cut from circle J1 to edge of circuit board signal To change the chime from non-coded to coded (single- stroke) operation cut from circle J2 to edge of circuit board To change the chime from high dB to low dB cut J3 trace between holes sound output level Figure 1: Chime settings Note: Polarity shown in alarm condition To next device or end of line device - + - + From compatible fire alarm control panel + - + - Figure 2: Constant non-coded voltage operation Genesis device with Genesis Signal Master [1] - + HS - + To next device or end of line device Continuous power source Coded power source + + - - + - Figure 3: Single-stroke coded voltage operation