Electrical-Electronics-Engineering.pdf

Scheme of Teaching and Examination for
5 th Semester of 3 Years Diploma in E.E.E.
Duration of Semester : 14 Weeks
Student Contact Hours : 36 Hrs
Total Marks : 800
Effective from : 2017 -18 Session
Sl.
No.
Name of Subject Subject Code Subject
Teaching
Scheme
Examination Scheme
L T P
Hours
of
Exam
Full
Marks of
Subject
Final Exam
/ committee
marks
Internal
Assessment
Pass Marks
Final / Ext.
Exam
Pass
Marks in
Subjects
1. Instrumentation System ECE 503 Theory 3 - 3 100 80 20 26 40
2. Electrical Machines II ELE 504 Theory 3 - - 3 100 80 20 26 40
3. Electronics Sys. Design &
Maintenance
EEE 503 Theory 3 - - 3 100 80 20 26 40
4. Elective I ELE 506/CSE503/ECE505 Theory 3 - - 3 100 80 20 26 40
5. Elective II ELE
507/ECE406/CSE506/ELE508
Theory 3 - - 3 100 80 20 26 40
6. Electrical Machines II Lab ELE 509 Practical - - 2 4 50 40 10 - 20
7. Instrumentation System
Lab
ECE 512 Practical - - 2 4 50 40 10 - 20
8 Elective I lab ELE 511/ELE512/ELE513 Sessional - 2 - 50 30 20 - 25
9. Elective II Lab ELE
514/ECE410/CSE514/ELE515
Sessional - - 2 - 50 30 20 - 25
10 In Plant Training 502 sessional - - - - 50 30 20 - 25
11. DLS 501 Sessional - - 4 - 50 30 20 - 25
Total Hours of Teaching per week : 15 12
Elective I (Illumination Engineering- ELE 506/ Micro. Processor & Micro. Controller- CSE503/ PLC- ECE505)
Elective II (Maintenance of Electrical Machines ELE507/Control System ECE406/Mobile Computing- CSE 506/ Robotics & Smart System-ELE508)
Total Marks: Theory : Practical : Sessional :
L : Lecture, T : Tutorial P : Practical
Note: 1. Period of Class hours should be of 1 hrs duration as per AICTE norms.
2. Remaining Hrs every week has been marked for students for Library and Student Centered Activities.
3. Drawing / Graphics / Practical / Sessional examinations will be held at parent institution.
4. Board will depute examiner for Practical examination.
5. Regarding sessional examination the parent institution will form a three member committee and this committee will examine the sessional records and
hold viva of the examinee for 60 % marks allotted to the subject. Marks for remaining 40 % will be provided by the Faculty concerned on the basis of
evaluation of each job / work throughout the semester.
6. Inplant Traning of 04 weeks duration to be undertaken after 4th semester Exam and before start of 5th semester classes.

Subject : Instrumentation System /Electronics Measurements
Subject Code : ECE503
Total Hours : 42
Full Marks : 80 + 20 = 100
Unit I Electronic Meters: 6 hrs
Electronic Analog voltmeter: DC voltmeters-Choppers type-DC amplifier, solid state voltmeter,
Differential voltmeter, peak responding voltmeter, True RMS voltmeter, calibration of DC voltmeters.
Digital Voltmeter:- Introduction, Ramp Techniques, dual slope, integrating type DVM, Successive
approximation type DVM, Resolution and sensitivity of digital meters, general specification of a
DVM. CRO’s study of various stages in brief, measurement of voltage, current phase and
frequency, special purpose oscilloscope.
Unit II Instrumentation for Generation and Analysis of Waveforms: 6 hrs
Signal generators: Fixed and variable AF oscillators, AF sine and square wave generator, Function
generator: Square and pulse generator, Sweep generator, wave analyzer, harmonic distortion analyzer,
spectrum analyzer, spectrum analysis.
Unit III Storage and Display Devices: 4 hrs
Necessity of recorders, recording requirements, graphic recorders, strip chart recorders, magnetic
tape recorders, digital tape recorders. Electronic indicating instruments, seven segment display,
fourteen segmental display Nixie tube.
Unit IV Transducers and DATA Acquisition Systems: 6 hrs
Strain gauge, LVDT, thermocouple, piezoelectric, crystal and photoelectric transducers and their
applications. Data acquisition systems. Unit VII Telemetry: Introduction, method of data
transmission, types of telemetry systems and applications.
UNIT V Instrumentation : 6 hrs
Types of Instrumentation systems, Data acquisition system (DAS) and its uses in intelligent
Instrumentation system, Detailed study of each block involved in making of DAS, Signal
Conditioners: as DA, IA, Signal Converters (ADC & DAC), Sample and hold, Designing of Pressure,
Temperature measuring instrumentation system using DAS, Data logger.
UNIT VI AUTOMATION 4 hrs
Introduction about Automation system, Concepts of Control Schemes, Types of Controllers,
Components involved in implementation of Automation system i.e., DAS, DOS, Converter ( I to P )
and Actuators: Pneumatic cylinder, Relay, Solenoid (Final Control Element), Computer Supervisory
Control System (SCADA), Direct Digital Control’s Structure and Software.
UNIT VII PLC & INTELLIGENT CONTROLLER : 10 Hrs
Introduction of Programmable logic controller, Principles of operation, Architecture of Programmable
controllers, Programming the Programmable controller. Introduction to Intelligent Controllers, Model
based controllers, Predictive control, Artificial Intelligent Based Systems, Experts Controller, Fuzzy
Logic System and Controller, Artificial Neural Networks, Neuro-Fuzzy Controller system.

Subject : Instrumentation System Lab /Electronics Measurements
1 To determine output characteristic of a LVDT and determine its sensitivity.
2 Study characteristics of temperature transducer like Thermocouple, Thermistor and RTD with
implementation of small project using signal conditioning circuit.
3 Study characteristics of Light transducer like Photovoltaic cell, Phototransistor and Pin
Photodiode with implementation of small project using signal conditioning circuit.
4 To study input- output characteristics of a potentiometer and to use two potentiometers as an
error detector.
5 To study transmitter- receiver characteristics of a synchro set to use the set as control
component.
6 To study the operation of a d-c positional servo system and to investigate the effect of
damping and supply voltage on its response.
7 To study the operation of an a.c. position servo-system and to obtain effects of supply voltage
and system parameter on its transient response.
8 To study a stepper motor and control its direction speed and number of steps with the help of
a microprocessor
9. ADC Converter
10. DAC converter
11. Study of Automation system
12. Intelligent controller
Suggested Readings / Books:
1 Electrical and Electronic Measurements and Instrumentation, by K. SAWHNEY.
2 Electronic Instrumentation and Measurement Techniques, by D Cooper.
3 Electronic Instrumentation, by H.S. Kalsi, Tata McGraw Hill
4 Applied Electronics Instrumentation and measurement, David Buchla, Wayne Melachlan:
5 Electronics Measurement and Instrumentation, Oliver by B.H and Cag J.M. McGrawHill.
6 Element of Electronic Instrumentation & Measurement, by Carr, Pearson Education.
7 Electronic Measurements & Instrumentation, by Kishore, Pearson Education.
8 Process Control Systems and Instrumentation, Bartelt, Cengage Learning
9 Process Control Instrumentation Technology‖ 6/e, by Curtis D Johnson, Pearson Ed.
10 Computer-Based Industrial Control‖, by Krishna Kant, PHI.

Subject : Electrical Machine -II
Subject Code : ELE504
Total Hours : 42
Full Marks : 80 + 20 = 100
Contents: Theory
Chapter Name of the Topic Hours
01
Three phase induction motor
1.1 Construction of three phase induction motor
1.2 Production of rotating magnetic field
1.3 Principle of working/operation
1.4 Concept of slip
1.5 Equation of rotor induced emf, current, frequency, reactance,
and impedance under steady and running condition
1.6 Torque equation of three phase induction motor
1.7 Starting and running torque of squirrel cage and slip ring
induction motor
1.8 Condition for maximum and starting torque
1.9 Torque slip characteristics of three phase induction motor
1.10 Effect of change in rotor circuit resistance on torque-slip
characteristics
1.11 Effect of change in supply voltage on torque-slip characteristics
08
1.12 measurement of slip by
a) Tachometer method
b) Comparing rotor frequency and stator frequency
1.13 Speed control of three phase induction motor by
a) Pole changing method
b) Frequency control method
c) By stator voltage control
d) Rotor resistance control
1.14 Comparison between squirrel-cage and slip-ring induction
motor.
1.15 Applications of three phase induction motor.
1.16 Power stages of three phase induction motor.
(Numerical on all above)
1.17 Double cage IM
a) Construction
b) Characteristic of outer, inner cage & combined characteristic
c) Industrial Applications
1.18 I.M. as a generalized transformer
1.19 Vector diagram of IM
08
1.20 Equivalent circuit of 3-phase IM (No numerical)
1.21 Starting of 3-phase IM (No numerical)
a) Stator resistance starter
b) Star-Delta starter
c) Auto transformer starter
d) Rotor resistance starter
02

02
Three Phase Alternator
2.1 Definition and construction of three phase Alternator
a) Armature
b) Rotor- smooth cylindrical & projecting type
2.2 Derivation of e.m.f. equation of Alternator which includes
a) Chording factor
b) Distribution factor
04
2.3 Factors affecting the terminal voltage of Alternator
a) Armature resistive drop
b) Leakage reactance drop
c) Armature reaction at various power factors & concept of
Synchronous impedance
2.4 Regulation of three phase Alternator by
a) Synchronous impedance method
b) mmf method
(Numerical on all above)
04
03
Synchronous Motor
3.1 Principle of working/operation
3.2 Synchronous Motor on load with constant excitation
3.3 Effect of excitation at constant load
3.4 V curve & inverted V curve
3.5 Hunting & phase swinging
3.6 Applications
3.7 Starting of Synchronous Motor
3.8 Comparison between IM & Synchronous Motor
(Numerical on all above )
06
04
Single phase Motors
4.1 Double field revolving theory
4.2 Types of Single phase IM
4.3 Split phasing principle of starting
a) Resistance start induction run
b) Capacitor start induction run
c) Capacitor start Capacitor run
d) Double value Capacitor applications motor
4.4 Shaded pole IM
4.5 Applications
06
05
Special machines
5.1 Induction Generator: Principle of operation, Construction and
Applications
5.2 Linear Induction Motor Principle of operation, Construction and
Applications
5.3 AC series motor Principle of operation, Construction and
Applications
04
Total 42

Subject : Electrical Machine -II Lab
Practical:
Intellectual Skills: 1. Analytical Skills 2. Identification Skills
Motor Skills : 1. Measuring Skills 2. Connecting instruments
List of Practical:
1) a) To measure the slip of 3-phase IM by
i) Tachometer
ii) Comparing rotor & stator frequency
iii) Stroboscopic method.
b) To reverse the direction of rotation of 3-phase IM.
2) To measure the performance of 3-phase IM by direct loading
3) To list different types of starters used for 3-phase IM .Identify & use the same to start & run
3-phase IM
4) Using an MG set (DC motor-Alternator) observe the effect of excitation & speed on
induced e.m.f. & plot O.C.C. of the given alternator.
5) To find the percentage regulation of 3-phase alternator by synchronous impedance method at
various power factors.
6) To find the percentage regulation of 3-phase alternator by direct loading method at various
power factors.
7) To list & explain various starting methods of synchronous motor & applying one of
them to start the synchronous motor. Plot V & inverted V curve of the same.
8) To list the various types of 1-phase IM, Collect the literature for them from
dealers/manufacturers of local places & compare on the following pts.
i) Method of starting ii) Cost iii) Performance iv) Starting
torque etc. Prepare a report
Learning Resources: Books:
Sr. No. Author Title Publisher
01 S. K. Bhattacharya Electrical Machines TTTI, Chandigarh
02 B. L. Theraja Electrical Technology Vol. II S Chand & Co.
03 C. L. Dawes Electrical Technology --
04 P. S Bhimbra Electrical Machines
05 D.P. Khothari Electrical Machines
06 J. B. Gupta Electrical Machines
07 Ashfaq Hussain Electrical Machines
08 G. K Dubey Electrical Drives
09 A. Chakraborty Electrical Machines
10 M. G. Say Electrical Machines & Design

Subject : Electronic System Design & Maintenance
Subject Code : EEE503
Total Hours : 42
Full Marks : 80 + 20 = 100
Content
1. Data Transfer Equipments 4 Hrs
Modems – Internal Modem, External Modem and Cable Modems set top boxes, line
amplifiers, reverse path amplifiers, Distributions amplifiers – their working principle,
operation, Installation, maintenance and repairing.
2. Switches 6 Hrs
ATM Switch, Ethernet Switch, Fast Ethernet Switch, FDDI Switch, FDDI/Ethernet
Switch, Fiber Channel Switch, Multi service Switch and Routing Switch – their
working principle, operation, Installation, maintenance and repairing.
3. Hubs 6 Hrs
100ZVG Hub, ATM Hub, Ethernet Hub, FDDI Hub, Fiber Channel Hub, Repeater
Hub, USB Hub, Wireless Hub – their working principle, operation, Installation,
maintenance and repairing.
4. Router 6 Hrs
ISDN Router, Cable/DSL Routers, Ethernet and ATM WAN Routers, Power supplies
for Router with IP- Voice software, Board Band Router their working principal,
operation, High Data Rate Terminal – their working principal, operation, Installation,
5. Earth Station 4 Hrs
Fixed and Mobile earth Station, BBP mode/MSM mode of Operations, High Data
Rate Terminal – their working principle, operation Installation, maintenance and
repairing.
6. ISDN 3 Hrs
NT, Terminal Adopter their working principle, operation, Installation, maintenance
and repairing.
7. UPS 3 Hrs
On-Line, Off- Line interactive UPS – their working principle, operation, Installation,
8. ATM 6 Hrs
Fundamentals of ATM, ATM adaptation layer, virtual paths and virtual channels,
ATM signaling, addressing, NNI, LAN emulation, MPOA, ATM in WAN, Switch
designs, traffic management, voice over ATM and ATM’s relationship to DSL.
9. Cell Phone 4 Hrs
Study of the front panel & identification and function of different buttons. Disassembling &
assembling of different units & Servicing of Cell Phone, Identification of problems,
troubleshooting & repairing.

Subject : Illumination Engineering (Elective-I)
Total Hours : 42
Full Marks : 80 + 20 = 100
Contents: Theory
Chapter Name of the Topic Hours
1
Fundamentals of Illumination
1.1 Illumination Terminology
1.2 Laws of Illumination
1.3 Featuring of good Illumination scheme
1.4 Advantages of good Illumination scheme
1.5 Measurement of level of Illumination (simple illumination)
06
2
Lamps & Lighting Accessories
2.1 Types of lamps: ARC lamps, HPMV lamps, Sodium
Lamps, CFL Lamps, Metal halides, LED lamps
2.2 Neon Sign Tubes.
2.3 Neon Lamps.
2.4 Halogen Lamps.
2.5 Construction, working principle, advantages, disadvantages
& Application of incandescent & Flurocent
2.6 Lighting accessories. (All fittings, switches, enclosers )
2.7 Illumination Auditing
08
3
Illumination Control & Control Circuits
3.1 Purpose of lighting control
3.2 Dimmer & Dimmer Transformer & their types
3.3 Electronic Dimmer
3.4 Enhancing Lighting control.
3.5 Control circuits for lamps (refer) : ON/OFF control &
Illumination control.
06
4
Illumination for Interior Applications
4.1 Standard for various situations of Interior Illumination
4.2 Design Techniques
4.3 Design considerations for Interior location of Residential,
Commercial, Industrial premises
4.4 Design Illumination scheme for different Interior locations
of Residential, Commercial, Industrial unit.
08
5
Illumination for Outdoor Applications
5.1 Factory Lighting
5.2 Street Lighting (Latest Technology)
5.3 Flood Lighting
5.4 Railway Lighting
5.5 Lighting for Advertisement/Hoardings
5.6 Sports Lighting
08
6
Lighting for Special Applications
6.1 Agriculture & Horticulture
6.2 Health Care Centers / Hospitals
6.3 Decorating Purposes
6.4 Stage Lighting
6.5 Aquariums & Shipyards
6.6 Special purpose lamps used in photography video films.
06
Total 42

Subject : Illumination Engineering Lab (Elective-I)
Practical:
Skill to be developed:
Intellectual
Skills:
1. Apply different Designing Skills.
2. Select proper
equipment. Motor Skills:
1. Measurement of Illumination.
2. Drawing skills.
List of Practicals:
1. To Measure Illumination by luxmeter.
2. Visit to nearby lamp manufacturing industry.
3. Prepare a report of different luminaries available in the market & collect the technical
data
(Visit local market / Use internet for data collection).
4. Study the different lighting accessories required for varies types of lamps.
5. Design an Illumination scheme for a garden of medium size.
6. Design an Illumination scheme for a conference room of medium size.
7. Design an Illumination scheme for a workshop for fine work of medium size.
8. Design an Illumination scheme for a medium size Hotel / Hospital /Shopping complex.
Learning Resources:
1. Books:
Sr. No. Author Name of Book Publisher & Address
1. Jack L. Lindsey
Applied Illumination
Engineering
The Fairmont Press Inc.
2.
R. H. Simons, Robert
Bean
Lighting Engineering:
Applied Calculations
Architectural Press (ISBN
0750650516)
3. Casimer M Decusatis
Handbook of Applied
Photometry
Springer (ISBN
1563964163)

Subject : Microprocessor & Microcontroller (Elective-I)
Subject Code : CSE503
Total Hours : 42
Full Marks : 80 + 20 = 100
OBJECTIVES:
The student should be made to:
Study the Architecture of 8085 and 8086 microprocessor.
Learn the design aspects of I/O and Memory Interfacing circuits.
Study about communication and bus interfacing.
Study the Architecture of 8051 microcontroller.
UNIT I THE 8085 MICROPROCESSOR 4 Hrs
Introduction to 8085 – Microprocessor architecture , pin out diagram, – Addressing modes -
Instruction set, Interrupts and interrupt service routines.
UNIT II THE 8086 MICROPROCESSOR 8 Hrs
Introduction to 8086 – Microprocessor architecture – Addressing modes - Instruction set and
assembler directives – concept of pipelining, Assembly language programming – Modular
Programming - Linking and Relocation - Stacks - Procedures – Macros – Interrupts and interrupt
service routines – Byte and String Manipulation.
UNIT III 8086 SYSTEM BUS STRUCTURE 6 Hrs
8086 signals – Basic configurations – System bus timing –System design using 8086 – IO
programming – Introduction to Multiprogramming – System Bus Structure - Multiprocessor
configurations – Coprocessor, Closely coupled and loosely Coupled configurations.
UNIT IV I/O INTERFACING 6 Hrs
Memory Interfacing and I/O interfacing - Parallel communication interface – Serial communication
interface – D/A and A/D Interface - Timer – Keyboard /display controller – Interrupt controller –
DMA controller – Programming and applications Case studies: Traffic Light control, LED display ,
LCD display, Keyboard display interface and Alarm Controller.
UNIT V MICROCONTROLLER 6 Hrs
Architecture of 8051 – Special Function Registers(SFRs) - I/O Pins Ports and Circuits - Instruction
set - Addressing modes - Assembly language programming.
UNIT VI INTERFACING MICROCONTROLLER 9 Hrs
Programming 8051 Timers - Serial Port Programming - Interrupts Programming – LCD & Keyboard
Interfacing - ADC, DAC & Sensor Interfacing - External Memory Interface- Stepper Motor and
Waveform generation.

TEXT BOOKS:
1 Microprocessor Architechture, Programming and Applications with 8085 by Ramesh K
Goankar, Galgotia Pub
2 Digital Computer System by Malvino ( 2nd
Ed) TMH
3. Yu-Cheng Liu, Glenn A.Gibson, “Microcomputer Systems: The 8086 / 8088 Family -
Architecture, Programming and Design”, Second Edition, Prentice Hall of India, 2007.
4. Mohamed Ali Mazidi, Janice Gillispie Mazidi, Rolin McKinlay, “The 8051 Microcontroller
and Embedded Systems: Using Assembly and C”, Second Edition, Pearson education, 2011.
REFERENCE: 1. Doughlas V.Hall, “Microprocessors and Interfacing, Programming and
Hardware”,TMH,2012
Subject : Microprocessor & Microcontroller Lab (Elective-I)
LIST OF EXPERIMENTS:
8086 Programs using kits and MASM
1. Basic arithmetic and Logical operations
2. Move a data block without overlap
3. Code conversion, decimal arithmetic and Matrix operations.
4. Floating point operations, string manipulations, sorting and searching
5. Password checking, Print RAM size and system date
6. Counters and Time Delay
7. Traffic light control
8. Stepper motor control
9. Digital clock
Key board and Display
11. Printer status
12. Serial interface and Parallel interface
13. A/D and D/A interface and Waveform Generation using 8051
14. Basic arithmetic and Logical operations
15. Square and Cube program, Find 2‟s complement of a number
16. Unpacked BCD to ASCII

Subject : Programmable Logic Controller (Elective-I)
Total Hours : 42
Full Marks : 80 + 20 = 100
Content
1. PLC Basics : 6 hrs
An Overall Look at Programmable Logic Controllers - Introduction, definition &
history of the PLC, manufacturing & assembly process, PLC advantage &
disadvantage, overall PLC system, CPU & programmer/monitors, PLC input & output
modules, printing PLC information. The PLC: A Look Inside - Introduction, the PLC
as a computer, the central processing unit, solid state memory, the processor, I/O
modules, power supplies. General PLC Programming Procedures - Introduction,
programming equipment, programming formats, proper construction of PLC ladder
diagrams, process scanning consideration, PLC operational faults. Devices to Which
PLC Input and Output Modules Are Connected - Introduction, input ON/OFF
switching device, input analog device, output ON/OFF device, output analog devices
2. PLC Programming : 6 hrs
Programming On/Off Inputs to Produce On-Off Outputs - Introduction, PLC input
instruction, output: coils, inductors & others, operational procedures, contact & coil
input/output programming examples, a look at fail safe circuit, industrial process
examples. Relation of Digital Gate Logic to Contact/Coil Logic - Digital logic gates,
Boolean algebra PLC programming, conversion examples. Creating Ladder Diagrams
from Process Control Descriptions - Ladder diagram & sequence listing, large process
ladder diagram construction, flow charting as programming method
3. PLC Functions : 6 hrs
Register - Introduction, general characteristics of registers, module addressing,
holding registers, input registers: single & group, output registers: single & group.
PLC Timer Functions - Introduction, PLC timer functions, examples of timer function
industrial application, industrial process timing application. PLC Counter Functions -
Introduction, PLC counters examples of counter function industrial application
4. Intermediate Functions : 6 hrs
PLC Arithmetic Functions - Introduction, PLC addition & subtraction, the PLC
repetitive clock, PLC multiplication, division & square-root: PLC trigonometric & log
function, other PLC arithmetic functions. PLC Number Comparison Functions -
Introduction, PLC basic comparison function, PLC basic comparison function
application, PLC advanced comparison function. Numbering Systems and PLC
Number Conversion Functions - Introduction, numbering system: decimal, binary &
BCD, PLC conversion between decimal & BCD, OCTAL & HEX DECIMAL
numbering system, other numbering & code system
5. Date Handling Functions 6 hrs
The PLC SKIP and MASTER CONTROL RELAY Functions - Introduction, the
SKIP function & application, the MASTER CNTROL RELAY function &
application. Jump Functions - Introduction, jump with non-return, jump with return.
PLC Data Move Systems - Introduction, PLC MOVE function & application, moving
large blocks of PLC data, PLC table & registers moves, other PLC MOVE functions.

Other PLC Data Handling Functions - Introduction, PLC FIFO functions, the FAL
function, the one shot (ONS), clear (CLR) & SWEEP functions
6. Working with Bits 8hrs
PLC Digital Bit Functions and Applications - Introduction, bit pattern in a register,
changing a register bit status, shift register function, shift register application. PLC
Sequencer Functions - Introduction, electromechanical sequencing, the basic PLC
sequencer function, a basic PLC sequencer application with timing, other PLC
sequencer function, cascading sequencer. Controlling a Robot with a PLC -
Introduction, basic two axis ROBOT with PLC sequencer control, industrial three axis
ROBOT with PLC control. PLC Matrix Functions - Introduction, applying matrix
functions to reduce program length, the PLC AND & OR matrix function, the PLC
COMPLEMENT & OMPARE matrix function, combination PLC matrix operation
7. Advanced PLC Functions : 4 hrs
Analog PLC Operation - Introduction, types of PLC, analog modules & systems, PLC
analog signal processing, BCD or multi-bit data processing, PLC analog output
application examples.
Subject : Programmable Logic Controller Lab (Elective-I)
List of Experiments:
Based on the theoretical paper, faculty will be decide minimum 10 Experiments to be
performed by the Students.
Books :
1. Programmable Logic Controllers : Principles & Applications, John W. Webb and
Ronald A.Reis, Prentice Hall India
2. Programmable Logic Controllers by Bolton, Elsever N Publication
3. Programmable Logic Controllers by FD Prestrusela, TMH
4. Programmable Logic Controllers: Programming Methods and Applications by John R.
Hackworth and Frederick D. Hackworth Jr, Pearson

Subject : Maintenance of Electrical Machines (Elective-II)
Full Marks : 80+20=100
Hours : 42
1. Safety and Accidents - 6 Hrs
Definition of terminology used in safety: Safety, hazard, accident, major accident hazard,
responsibility, authority, accountability, monitoring.
I.E. Act & statutory regulations for safety of persons and equipment working with electrical
installation, causes of electrical accidents, preventive measures, electrical shocks, precaution
to be taken against electrical shock, treatment for electrical shock. Causes of electrical fires,
precaution to be taken to avoid fire, action to be taken in case of fire, fire fighting equipments.
2. General Introduction - 7 Hrs
Concept of routine, preventive and breakdown maintenance, Advantages of preventive
maintenance, procedure for developing preventive maintenance schedule, factors affecting
preventive maintenance schedule. Introductionto total productive maintenance.
3. Maintenance of Rotating machines 7 Hrs
Routine, preventive and breakdown maintenance of 1& 3 phase induction motors,
Synchronous machines and D.C machines
4. Maintenance of transformer 6 Hrs
Preventive and routine maintenance of distribution transformers, Periodic checks for
replacement of oil, Silica gel, properties of a good transformer oil.
5. Maintenance of insulation 6 Hrs
Classification of insulating, factors affecting life of insulating materials, measurement of
insulation resistance, interpretation of conditions, agents that contaminate insulating oil, tests
on insulating oil (a) Acidity test (b) Sludge test (c) Crackle test (d) flash point test
Filtration of insulating oil for protection of electrical equipments (insulation) during period of
inactivity.
Procedure for cleaning, washing and drying insulation and revarnishing
Methods of internal heating & vaccum impregnation.
6. Troubleshooting of electrical machine & switchgear. 10 Hrs
Significance of trouble shooting of various electrical machines and describes the procedure
for the same. Internal and external causes of failure of equipment, various types of faults
(mechanical, electrical of magnetic) in electrical machines, Reason for their occurrences, use
of following tools: Bearing puller, Filler gauge, dial indicator, spirit level, megger, earth
tester, growler,
Trouble shooting charts for 1 & 3 phase induction motor, 1 & 3 Phase transformer.
List the common trouble in electrical installation and cables.
Maintenance and trouble shooting of LVS switchgear like MCCB, ELCB, Contactors & Batteries.

Subject : Maintenance of Electrical Machines Lab (Elective-II)
List of Practical’s
1 Safety precautions in lab while doing electrical work
2 Safety equipments study
3 Winding of Fan coil
4 Winding of single motor
5 Winding of three phase motor
6 Repairing of single phase transformer
7 Repairing of wiring system
8 Installation of machine
9 Repairing of starter
10 Repairing of mains
11 Study of various types of MCB and other circuit breakers
Books :-
1. Electricals Protection & Switchgear by S.S. Rao
2. Maintenance of Electrical Machine by J.B. Gupta
3. Testing Commisioning Operation & Maintenance Of Electrical Equipment by S. Rao
4. Installation Maintenance And Repair Of Electrical Machines And Equipments by
Madhvi Gupta
5. Testing And Maintenance Of Electrical Machines by B.P. Patil

Subject : Control System Lab
Subject Lab : ECE406
Total Hours : 42
Full Marks : 100 (80+20)
L T P
3 2
1. Introduction: 04 hrs
Elements of control systems, concept of open loop and closed loop systems, Examples and
application of open loop and closed loop systems, brief idea of multivariable control systems.
2. Mathematical Modeling of Physical Systems: 06 hrs
Representation of physical system (Electro Mechanical) by differential equations,
Determination of transfer function by block diagram reduction techniques and signal flow
method, Laplace transformation function, inverse Laplace transformation
3. Time Response Analysis of First Order and Second Order System: 08 hrs
Characteristic Equations, response to step, pulse , impulse, ramp and parabolic inputs.
Transient response analysis, steady state errors and error constants, Transient & steady state
analysis of LTI systems
4. Frequency Response Analysis: 06 hrs
Frequency response, correlation between time and frequency responses, polar and inverse
polar plots, Bode plots
5. Control System Components: 04 hrs
Constructional and working concept of ac servomotor, synchronous and stepper motor
6. Stability and Algebraic Criteria: 04 hrs
concept of stability and necessary conditions, Routh-Hurwitz criteria and limitations. Root
Locus Technique: The root locus
concepts, construction of root loci.
7. Stability in Frequency Domain: 04 hrs
Nyquist stability criterion, assessment of relative stability: gain margin and phase margin, M
and N Loci, Nichols chart.
8. Study of preliminary considerations of lead, lag and lead-lag networks, closed loop systems
using compensation techniques in time domain and frequency domain. 04 hrs
9. Controllers : 02 hrs
Brief idea of proportional, derivative and integral controllers.

Subject : Control System Lab
Subject Lab : ECE410
L T P
2
1. Transfer function of first and second order system
2. Sensors system control system study
3. AC position servo system study
4. DC position servo system study
5. Control through magnetic amplifier
6. Measurement of passive elements R , L and C using Bridge Networks
7. Study of transducers and characterization
8. Digital simulation of linear systems
9. Stability Analysis of Linear system using MATLAB or equivalent Software
10. Study the effect of P, PI, PID controllers using MATLAB or equivalent Software or
with conventional methods.
11. Study of Lead and Lag compensator
BOOKS:
1. J.Nagrath and M.Gopal, “Control System Engineering”, New Age International Publishers, 5th
Edition, 2007.
2. Benjamin. C. Kuo, “Automatic control systems”, Prentice Hall of India, 7th Edition,1995.
3. M.Gopal, “Control System – Principles and Design”, Tata McGraw Hill, 2nd Edition, 2002.
4. Schaum’s Outline Series, “Feedback and Control Systems” Tata Mc Graw-Hill, 2007.
5. John J.D’Azzo & Constantine H.Houpis, “Linear Control System Analysis and Design’”, Tata
Mc Graw-Hill, Inc., 1995.
6. Richard C. Dorf and Robert H. Bishop, “Modern Control Systems”, Addison – Wesley, 1999.

Subject : Mobile Computing (Elective-II)
Total Hours : 42
Full Marks : 80 + 20 = 100
Unit-I
Introduction 10 hrs
Issues in mobile computing, overview of wireless telephony: cellular concept, GSM: air-interface,
channel structure, location management: HLR-VLR, hierarchical, handoffs, channel allocation in
cellular systems
Unit II
Mobile Network & Transport Layer 12 hrs
Mobile IP Goals, assumptions, entities and terminology, IP packet delivery, agent advertisement and
discovery, registration, tunnelling and encapsulation, Dynamic Host Configuration Protocol (DHCP),
Traditional TCP, Indirect TCP, Snooping TCP, Mobile TCP, Fast retransmit/fast recovery,
Transmission /time-out freezing, Selective retransmission, Transaction oriented TCP.
Unit III
Wireless Networking 10 hrs
Wireless LAN Overview: MAC issues, IEEE 802.11, Blue Tooth, Wireless multiple access protocols,
TCP over wireless, Wireless applications, data broadcasting, Mobile IP, WAP: Architecture, protocol
stack, application environment, applications.
Unit IV
Mobile Ad hoc Networks 10 hrs
Mobile Agents computing, security and fault tolerance, transaction processing in mobile computing
environment, Mobile Ad hoc Networks (MANETs): Overview, Properties of a MANET, spectrum of
MANET applications, routing and various routing algorithms, security in MANETs.

Subject : Mobile Computing Lab (Elective-II)
List of Experiments
1. Baseband communication
2. Adaptive Linear equalizer
3. CDMA multi path
4. CDMA Multiuser
5. Global System for Mobile Communication
6. GSM Wireless digital communication on digital SDR platform
7. GSM spread spectrum DSSS Modulation and demodulation
8. Free space propagation using path loss model
9. Link budget equation for sat communication
10. Carrier to noise ratio of wireless signal
11. Outdoor propagation Okumura model
12. Outdoor propagation Hata model
13. Selective retransmission
14. Tunneling and encapsulation,
15. Data broadcasting MANETs
Reference Books:
1. J. Schiller, Mobile Communications, Addison-Wesley, second edition, 2004.
2. Raj Pandya, Mobile & Personal Communication Systems and Service, PHI.
3. Asoke k Talukder , Roopa R Yavagal, Mobile Computing , Technology, Application & Service
Creation. Tata Mc Graw Hill
4. Stojmenovic and Cacute, ―Handbook of Wireless Networks and Mobile Computing‖, Wiley,

Subject : Robotics & Smart System (Elective-II)
Full Marks : 80+20=100
Hours : 42
Module-I [4Hrs]
Fundamentals: Define Robot, Classification of Robots, Define Robotics, History of
Robotics, Advantage and Disadvantages of Robots, Robot Components, Robot Sensing,
Robot Degree of Freedom, Robot Joints, Robot Coordinates, Robot Reference Frames,
Programming Modes, Robot Programming Language, Robot Applications.
Module-II [4 Hrs]
Robot Arm Kinematics: Robots as Mechanisms, Conventions, Matrix Representation:
Representation of a Point in Space; Representation of a Vector in Space, Representation of
Rigid Body, The Direct Kinematics Problem, The Inverse Kinematics Solution
Module-III [3 Hrs]
Robot Arm Dynamics: Lagrange-Euler Formulation, Newton-Euler Formation, Effective
Moments of Inertia, Generalized D'Alembert Equation of Motion.
Module-IV [4 Hrs]
Panning of Manipulator Trajectories: Path versus Trajectory, Basics of Trajectory
Planning, General Consideration on Trajectory Planning, Joint-interpolated Trajectories,
Planning of Manipulator Cartesian Path Trajectories.
Module-V [8 Hrs]
Control of Robot Manipulators: Characteristics of Actuating Systems, Comparison of
Actuating Systems, Hydraulic Actuators, Pneumatic Devices, Electric Motors: AC Motors;
DC Motors; Servomotors; Stepper Motors, Microprocessor Control of Electric Motors,
Magneto strictive Actuators, Speed Reduction.
Module-VI [8 Hrs]
Sensors: Sensor Characteristics, Sensor Utilization, Position Sensors: Potentiometers;
Encoders; LVDT; Resolves; LMDT; Hall-effect Sensors, Velocity Sensors: Encoders;
Tachometers; Differentiation of Position Signals, Acceleration Sensors, Force and Pressure
Sensors: Piezoelectric; Force Sensing Resistor; Strain Gauge, Torque Sensors, Micro
switches, Visible Light and Infrared Sensors, Touch Sensors, Proximity Sensors, Range
Finder, Sniff Sensors,.
Module-VII [5 Hrs]
Robot Programming Languages: Characteristics of Robot Level Languages, A brief about
AL and AML robot programming languages, Position Specification, Motion Specification,
Sensing and Flow of Control, Programming Support, Characteristics of Task Level
Languages, World Modelling, Task Specification, Robot Program Synthesis, Concluding
Remarks.

Subject : Robotics & Smart System Lab (Elective-II)
List of Experiments:
1. Configure the working of robots
2. Demonstrate the different types of sensor in robotics
3. Interface sensors using Microprocessor or Microcontroller
4. Measure various parameters of Electro-Mechanical Instruments Pressure, Flow, Speed and
Moisture
5. Interface Actuators using Microprocessor or Microcontroller
6. Interface Drives using Microprocessor or Microcontroller
7. Interface Stepper Motor using Microprocessor or Microcontroller
8. Use robot trainer to perform different tasks
9. Develop a Program for Line Follower Configuration.
10. Develop a Program for coffee maker configuration
Reference Books:
1. K.S. Fu, R.C. Gonzalez, C.S.G. Lee, “Robotics: Control, Sensing, Vision and
Intelligence”, McGraw Hill Education (India Ed.)
2. Saeed B. Niku, "Introduction to Robotics: Analysis, Control, Application 2/E", Wiley India
Edition
3. S.K. Saha, “Introduction to Robotics 2/E”, McGraw Hill Education (India Ed.)
4. R.K. Mittle, I.J. Nagrath, “Robotics and Control", McGraw Hill Education (India Ed.)
5. Thomas R. Kurfess, “Robotics and Automation Handbook", CRC Press
6. Ashitava Ghosal, "Robotics: Fundamental Concepts and Analysis 1/E", Oxford University
Press

Subject Title : Development of Life Skills (Common Paper)
Subject Code : 502
Full Marks : 50
Rationale:
In today’s competitive world, the nature of ind ividua l a nd organizations is
changing at very rapid speed. In this situation the responsibility of diploma holder is not
unique. After completing his course work he has to face the world and seek
meaningful employment also. Merely having knowledge is not sufficient these
days. He has to show his communicative skill also. As such the individual skills
with capability to show his strength and communicate his willingness new skills for
further advancement with to impart his ability and acquiring has to be displayed and
learned.
This subject will develop the student as an effective i n d i v i d u a l t o g r a b t h e
a v a i l a b l e s i t u a t i o n a n d b e member of the unseen team in which he may be put
in . It will develop the abilities and skills to perform at highest degree of quality as an
individual as well as a member of core group or team. Such skills will enhance his
capabilities in the field of searching, assimilating information, managing the given task,
handling people effectively, solving challenging problems.
Objectives: The students will be able to:
1. Develop acumen to face interview.
2. Lead in the group discussion and set goals and targets for others
3. Develop team spirit i.e. concept of working in teams
2. Apply problem solving skills for a given situation
3. Use effective presentation techniques
4. Apply techniques of effective time management
5. Apply task management techniques for given projects
6. Enhance leadership traits
7. Resolve conflict by appropriate method
8. Survive self in today’s competitive world
9. Follow moral and ethics
11. Convince people to avoid frustration
CONTENTS:
SOCIAL SKILLS
1. Social understanding for group discussion, imaginative thinking and develop free
ideas .
2. SWOT Analysis – Concept, and know himself in details. Learn how to make
use of SWOT.
3. Inter personal Relation:- How to effectively counter arguments of others without
hearting their feeling Sources of conflict and conflict resolution, Ways to enhance
interpersonal dependence and relations.
4. Problem Solving
I) STEPS IN PROBLEM SOLVING,
1) Identify and clarify the problem,
2) Information gathering related to problem,

3) Evaluate the evidence,
4) Consider alternative solutions and their implications,
5) Choose and implement the best alternative,
6) Review
II) Problem solving technique.(any one technique may be considered)
1) Trial and error
2) 2) Brain storming
3) 3) Lateral thinking
5. Presentation Skills
Body language --
Dress like the audience, Posture, Gestures, Eye contact and facial expression. STAGE
FRIGHT,
Voice and language – Volume, Pitch, Inflection, Speed, Pause, Pronunciation, Articulation,
Language, Practice of speech. Use of presentation aids, Summarizing the facts
6. Group discussion –
Introduction to group discussion, Ways to carry out group discussion, Parameters—
Contact, body language, analytical and logical thinking, decision making
7. INTERVIEW TECHNIQUE
Necessity, Techniques to influence interviews and giving directions, Tips for handling
common questions.
8. Working in Teams
Understand and work within the dynamics of a groups.
Tips to work effectively in teams,
Establish good rapport, interest with others and work effectively with them to meet
common objectives,
Tips to provide and accept feedback in a constructive and considerate way ,
Leadership in teams, Handling frustrations in group.
9. Task Management
Introduction, Task identification, Task planning ,organizing and execution, Closing the
task

BOOKS:
Sr.
No
Title of the book Author Publisher
1 Adams Time management Marshall Cooks Viva Books
2 Basic Managerial Skills for All E.H. Mc Grath , S.J. Pretice Hall of India
3 Body Language Allen Pease Sudha Publications Pvt.
Ltd.
4 Creativity and problem solving Lowe and Phil Kogan Page (I) P Ltd
5
Decision making & Problem
Solving
by Adair, J Orient Longman
6 Develop Your Assertiveness Bishop , Sue Kogan Page India
7 Make Every Minute Count Marion E Haynes Kogan page India
8 Organizational Behavior
Steven L McShane and
Mary Ann Glinow
Tata McGraw Hill
9 Organizational Behavior Stephen P. Robbins
Pretice Hall of India, Pvt
Ltd
10 Presentation Skills
Michael Hatton
( Canada – India
Project)
ISTE New Delhi
11
Stress Management Through
Yoga and Meditation
-- Sterling Publisher Pvt Ltd
12
Target setting and Goal
Achievement
Richard Hale ,Peter
Whilom
Kogan page India
13 Time management Chakravarty, Ajanta Rupa and Company
14 Working in Teams Harding ham .A Orient Longman
INTERNET ASSISTANCE
1. http://www.mindtools.com
2. http://www.stress.org
3. http://www.ethics.com
4. http://www.coopcomm.org/workbook.htm
5. http://www.mapfornonprofits.org/
6. http://www.learningmeditition.com http://bbc.co.uk/learning/courses/
7. http://eqi.org/
8. http://www.abacon.com/commstudies/interpersonal/indisclosure.html
9. http://www.mapnp.org/library/ethics/ethxgde.htm
10. http://www.mapnp.org/library/grp_cnfl/grp_cnfl.htm
11. http://members.aol.com/nonverbal2/diction1.htm
12. http://www.thomasarmstron.com/multiple_intelligences.htm
13. http://snow.utoronto.ca/Learn2/modules.html
14. http://www.quickmba.com/strategy/swot/

Electrical-Electronics-Engineering.pdf

More Related Content

Similar to Electrical-Electronics-Engineering.pdf (20)

Recently uploaded (20)

Electrical-Electronics-Engineering.pdf