Syllabus

Teaching and Examination Scheme for B. Tech. (Four Year
Course)
Branch Electrical Engineering Branch Code EE
Year II Semester III
Hrs./Week
Maximum
Marks
Code Subject Lecture Tutorial Practical
Duration
of
Exam.
(Hrs)
IA Exam
Total
3EE1 Power Electronics-I 2 1 3 20 80 100
3EE2 Computer Programming-I 3 3 20 80 100
3EE3 Circuit Analysis-I 3 1 3 20 80 100
3EE4 Electrical Machines-I 3 1 3 20 80 100
3EE5 Electrical Measurements 3 1 3 20 80 100
3EE6.1 Mathematics
3EE6.2
3EE6.3
3EE6.4

3 1 3 20 80 100
3EE7 Power Electronics Lab-I 2 2 45 30 75
3EE8 Computer Programming Lab-I 2 2 45 30 75
3EE9 Electrical Circuit Lab 2 2 45 30 75
3EE10 Electrical Machines Lab-I 2 2 45 30 75
3EE11 Electrical Measurement Lab 2 2 30 20 50
3EEDC
Discipline/Extra-Curricular
Activities
50
Total 17 5 10 330 620 1000
Total Teaching hours 32
Year II Semester IV
4EE1 Power Electronics-II 3 1 3 20 80 100
4EE2 Digital Electronics 3 3 20 80 100
4EE3 Electrical Machines-II 3 1 3 20 80 100
4EE4 Computer Programming -II 3 3 20 80 100
4EE5 Circuit Analysis-II 3 1 3 20 80 100
4EE6.1 Advanced Mathematics
4EE6.2
4EE6.3
4EE6.4
3 1 3 20 80 100

4EE7 Power Electronics Lab-II 2 2 45 30 75
4EE8 Digital Electronics Lab 2 2 45 30 75
4EE9 Electrical Machines Lab-II 2 2 45 30 75
4EE10 Computer Programming Lab-II 2 2 45 30 75
4EE11 Humanities & Social Sciences 2 2 30 20 50
4EEDC
Activities
50
Total 18 4 10 330 620 1000
Total Teaching hours 32Year III Semester V
5EE1 Power Electronics-III 3 1 3 20 80 100
5EE2
Microprocessors & Computer
Architecture
3 3 20 80 100
5EE3 Control Systems 3 1 3 20 80 100
5EE4 Generation of Electrical Power 3 1 3 20 80 100
5EE5
Transmission & Distribution of
Electrical Power
3 1 3 20 80 100
5EE6.1 Advanced Distribution System

5EE6.2
Principle of Communication
Systems
5EE6.3 Introduction to VLSI
5EE6.4
3 3 20 80 100
5EE7 Power Electronics Lab-III 2 2 45 30 75
5EE8 Microprocessor Lab 2 2 45 30 75
5EE9 MATLAB Programming Lab 2 2 45 30 75
5EE10 Power System Design 2 2 45 30 75
5EE11 Entrepreneurship Development 2 2 30 20 50
5EEDC
Activities
50
Total 18 4 10 330 620 1000
Year III Semester VI
6EE1 Modern Control Theory 3 1 3 20 80 100
6EE2 High Voltage Engineering 3 3 20 80 100
6EE3 Protection of Power System 3 1 3 20 80 100
6EE4 Advanced Power Electronics 3 1 3 20 80 100
6EE5 Data Structures in C 3 3 20 80 100

6EE6.1 Advanced Microprocessors
6EE6.2 Power System Instrumentation
6EE6.3
Digital Communication and
Information Theory
6EE6.4
3 1 3 20 80 100
6EE7 Control System Lab 2 2 45 30 75
6EE8 Power System Lab 2 2 60 40 100
6EE9 Data Structures Lab 2 2 45 30 75
6EE10 Advanced Power Electronics Lab 2 2 60 40 100
6EE11
6EEDC
Activities
50
Total 18 4 8 330 620 1000
Total Teaching hours 30Year IV Semester VII
7EE1 Data Base Management System 3 3 20 80 100
7EE2 Power System Analysis 3 1 3 20 80 100
7EE3 Artificial Intelligence Techniques 3 3 20 80 100
7EE4 Utilization of Electrical Power 3 1 3 20 80 100
7EE5 Power System Engineering 3 1 3 20 80 100

7EE6.1 Electromagnetic Field Theory
7EE6.2
Computer Aided Design of
Electrical Machines
7EE6.3
Economic Operation of Power
Systems
7EE6.4
3 3 20 80 100
7EE7 DBMS Lab 2 2 45 30 75
7EE8
Power System Modelling &
Simulation Lab
2 2 45 30 75
7EE9
Industrial Economics &
Management
2 2 30 20 50
7EE10 Project Stage I 2 2 50 50
7EE11 Practical Training & Industrial Visit 2 2 60 40 100
7EEDC
Activities

50
Total 18 3 10 350 600 1000
Year IV Semester VIII
8EE1 EHV AC/DC Transmission 3 1 3 20 80 100
8EE2 Electric Drives and Their Control 3 1 3 20 80 100
8EE3 Switchgear & Protection 3 3 20 80 100
8EE4.1 Non Conventional Energy Sources
8EE4.2
FACTS Devices & Their
Applications
8EE4.3 Power System Transients
8EE4.4
3 3 20 80 100
8EE5
Computer Based Power System
Lab
3 2 60 40 100
8EE6 Electrical Drives and Control Lab 3 2 60 40 100
8EE7 High Voltage Engineering Lab 2 2 30 20 50
8EE8 Seminar 2 2 60 40 100
8EE9 Project Stage II 4 2 120 80 200
8EEDC

Activities
50
Total 12 2 14 410 540 1000
Grand Total 100 23 62 2080 3620 6000B. TECH. III- SEMESTER
3EE1 POWER ELECTRONICS - I
Unit-1 PN Junction Diodes: Open-circuited p-n junction and space charge
region. The biased p-n
junction, volt-ampere characteristics, cutin voltage and effect of temperature
on V-I
characteristics. Minority carrier density distribution in (i) a forward biased
junction and (ii) a
reverse biased junction, diode capacitances, junction diode switching times
and characteristics.
Other Diodes: Avalanche breakdown and zener breakdown, working
principles of zener
diodes, photo-diodes, light emitting diodes, solar cell and varactor diodes.
Unit-2 Analysis of Diode Circuits: Diode as a circuit element, load line, small
signal diode model
and large signal diode model, analysis of half wave and full wave single-phase
rectifiers, peak
inverse voltage, various types of filters, their analysis and applications,
voltage multipliers,
clipping and clamping circuits.

Unit-3 Bipolar Junction Transistors (BJT): P-N-P and N-P-N transistors,
transistor current
components, common base (CB) and common emitter (CE) configurations:
input & output
characteristics, current Gains: alpha & beta, transistor operating regions:
active region,
saturation region and cutoff region, common collector configuration, BJT
biasing and DC
models, thermal stability and stabilization Techniques, small signal models:
h-parameters and
hybrid pie models, BJT as a switch, minority carrier concentration in the
base for cutoff, active
and saturation conditions, transistor switching times and characteristics,
transistor ratings.
Unit-4 Field Effect Transistors: Construction, working, V-I characteristics
and transfer
characteristics of JFET. MOSFET: Enhancement type and depletion type:
construction,
working, V-I characteristics, and transfer characteristics. DC analysis of
FETs. FET as a
voltage variable resistor. FET small signal models. FET as a switch. CMOS.
Unit-5 Small Signal Amplifiers: Analysis of BJT and JFET amplifiers at low
frequency: input and
out resistances, voltage and current gains, frequency response of common
emitter transistor
amplifier at high frequency. Miller’s theorem and its dual. Cascaded BJT
amplifiers.
Darlington pair and Bootstrapped Darlington circuit.

Reference/Suggested Books
1. J. Millman's & C. Halkias–Integrated Electronics: Analog & Digital Circuits
Systems,2/e
TMH
2. David A. Bell – Electronic Devices and Circuits, 5th Ed Oxford.
3. Millman & Halkias- Millmans Electronic Devices & Circuits 2/e TMH
4. Robert L. Boylested & Louis Nashelshky– Electronic Devices and Circuit
theory, PHI
5. Allen Mottershed – Electronic Devices and Circuits, PHI.
6. Jacob Millman, Arvin Grabel, Microelectronics, TMH.
7. Salivahanan: Electronic Devices and Circuits, TMH
3EE2 COMPUTER PROGRAMMING -I
Unit-1 PROGRAMMING IN C: Review of basics of C, structure & pointer type,
variables, singly
and doubly linked lists, I/O and text file handling, command line arguments.
Unit-2 OOP FUNDAMENTALS: Concept of class and object, attributes, public,
private and
protected members, derived classes, single & multiple inheritance.
Unit-3 PROGRAMMING IN C++: Enhancements in C++ over C in data types,
operators and
functions. Inline functions, constructors and destructors. Friend function,
function and operator
overloading.
Unit-4 Working with class and derived classes. Single and, multiple and
multilevel inheritances and
their combinations, virtual functions, pointers to objects.

Unit-5 Working with text files, templates, file handling in C++, Input output
flags and formatting
operations.
Reference/Suggested Books1. E. Balaguruswamy: Programming in ANSI C
4/e TMH
2. E. Balaguruswamy: Object Oriented Programming in C++ 4/e TMH
3. SAHAY: OBJECT ORIENTED PROGRAMMING WITH C++ , Oxford
4. HUBBARD : Programming with C++ 3/e (SIE) (Schaum's Outline Series)
5. C Gottfried: Programming in C, Schaum Series
6. Rambaugh James etal, "Object Oriented Design and Modeling",PHI-1997
7. Budd, Timothy, "An Introduction to Object Oriented Programming",
Pearson 2000
3EE3 CIRCUIT ANALYSIS-I
Unit-1 Introduction: Introduction to circuit elements and their
characteristics. Current and voltage
reference. Response of single element, double element and triple element
circuits. Resonance,
selectivity & Q-factor in ac circuits.
Network Analysis: Network voltages. Mesh & node systems of network
equations and their
comparison. Graph of network, tree, incidence matrix, fundamental circuit
functions, cut sets,
f-circuits analysis and f-cut set analysis, node and node pair analysis.
Duality. Method of
obtaining dual network.

Unit-2 Network Theorems: Thevenis’s, Norton's, Superposition, Reciprocity,
Compensation,
Millman's, Tellegen’s, Maximum power transfer and Miller`s theorems.
Unit-3 Polyphase Circuits: General Circuit Relations: Three Phase Star, Three
Phase Delta, Star and
Delta Combination, Four Wire Star Connection, Balanced Three Phase
Voltages And
Unbalanced Impedances. Power and Reactive Volt-Amperes in a 3-Phase
System. Power
Relations in AC Circuits: Instantaneous Power in AC Circuits, Power Factor,
Apparent Power,
Reactive Power, Power Triangle, Complex Power.
Unit-4 Non-Sinusoidal Waves: Complex Periodic Waves And Their Analysis
By Fourier Series.
Different Kinds of Symmetry, Determination of Co-Efficients. Average and
Effective Values
of a Non-Sinusoidal Wave, Power in a Circuit of Non-Sinusoidal Waves of
Current and
Voltage, Form Factor, Equivalent Sinusoidal Wave and Equivalent Power
Factor. Response of
Linear Network to Non-Sinusoidal Periodic Waves.
Unit-5 Time Domain and Frequency Domain Analysis: Response of networks
to step, ramp,
impulse, pulse and sinusoidal inputs. Time domain and frequency domain
analysis of circuits.
Shifting theorem, initial and final value theorems. Special signal waveforms
with Laplace
transform & applications to circuit operations.

1. Van Valkenburg – Network Analysis, PHI
2. Hayt & Kemmerly: Engineeirng Circuit Analysis 6/e (TMH)
3. J. Edminster & M. Nahvi: Electric Circuits (SIE), 5/e, Scaum’s Out Line.
4. Nagsarkar & Sukhija : Circuits & Networks, Oxford
5. John Bird-Electric Circuit Theory & Technology, ELSEVIER
6. D Roy Chodhary: Network & Systems, New Age
7. Ghosh & Chakrabarti: Network Analysis and Synthesis (TMH)
8. A. Chakarvorty: Circuit Theory. Publisher: Dhanpat Rai & Co. (p) Ltd.
3EE4 ELECTRICAL MACHINES-I
Unit-1 Electromechanical Energy Conversion: Basic principles of
electromechanical energy
conversion. Basic aspects and physical phenomena involved in energy
conversion. Energy
balance.
Unit-2 DC generators: Construction, Types of DC generators, emf equation,
lap & wave windings,
equalizing connections, armature reaction, commutation, methods of
improving commutations,
demagnetizing and cross magnetizing mmf, interpoles, characteristics,
parallel operation.
Rosenberg generator.
Unit-3 DC Motors: Principle, back emf, types, production of torque, armature
reaction & interpoles,

characteristics of shunt, series & compound motor, DC motor starting. Speed
Control of DC Motor: Armature voltage and field current control methods,
Ward Leonard method. Braking,
losses and efficiency, direct & indirect test, Swinburne’s test, Hopkinsion
test, field &
retardation test, single-phase series motor.
Unit-4 Transformers: Construction, types, emf equation. No load and load
conditions. Equivalent
circuits, Vector diagrams, OC and SC tests, Sumpner’s back-to-back test,
efficiency. voltage
regulation, effect of frequency, parallel operation, autotransformers,
switching currents in
transformers, separation of losses.
Unit-5 Polyphase Transformers: Single unit or bank of single-phase units,
polyphase connections,
Open delta and V connections, Phase conversion: 3 to 6 phase and 3 to 2
phase conversions,
Effect of 3-phase winding connections on harmonics, 3-phase winding
transformers, tertiary
winding.
1. A.E. Fitggerald, C.Kingsley Jr and Umans,”Electric Machinery” 6th Edition
McGraw Hill,
International Student Edition.
2. Kothari & Nagrath: Electric Machines 3/e,TMH
3. M.G. Say, “The Performance and Design of AC machines”, Pit man & Sons.
4. Guru: ELECTRIC MACHINERY 3E, Oxford

5. P. S. Bimbhra-Electrical Machinery, Khanna Pub.
6. Stephen J Chapman: Electric Machinery Fundamentals, McGraw-Hill
7. Husain Ashfaq ,” Electrical Machines”, Dhanpat Rai & Sons
8. Bhag S. Guru and Huseyin R. Hizirogulu, “Electric Machinery and
Transformers” Oxford
Uiversity Press, 2001
3EE5 ELECTRICAL MEASUREMENTS
Unit-1 Measuring Instruments: Moving coil, moving iron, electrodynamic and
induction
instruments-construction, operation, torque equation and errors. Applications
of instruments
for measurement of current, voltage, single-phase power and single-phase
energy. Errors in
wattmeter and energy meter and their compensation and adjustment.
Testing and calibration of
single-phase energy meter by phantom loading.
Unit-2 Polyphase Metering: Blondel's Theorem for n-phase, p-wire system.
Measurement of power
and reactive kVA in 3-phase balanced and unbalanced systems: One-wattmeter,
two-wattmeter
and three-wattmeter methods. 3-phase induction type energy meter.
Instrument Transformers:
Construction and operation of current and potential transformers. Ratio and
phase angle errors
and their minimization. Effect of variation of power factor, secondary burden
and frequency on

errors. Testing of CTs and PTs. Applications of CTs and PTs for the
measurement of current,
voltage, power and energy.
Unit-3 Potentiometers: Construction, operation and standardization of DC
potentiometers– slide wire
and Crompton potentiometers. Use of potentiometer for measurement of
resistance and
voltmeter and ammeter calibrations. Volt ratio boxes. Construction,
operation and
standardization of AC potentiometer – in-phase and quadrature
potentiometers. Applications
of AC potentiometers.
Unit-4 Measurement of Resistances: Classification of resistance.
Measurement of medium
resistances – ammeter and voltmeter method, substitution method,
Wheatstone bridge method.
Measurement of low resistances – Potentiometer method and Kelvin's double
bridge method.
Measurement of high resistance: Price's Guard-wire method. Measurement of
earth resistance.
Unit-5 AC Bridges: Generalized treatment of four-arm AC bridges. Sources
and detectors. Maxwell's
bridge, Hay's bridge and Anderson bridge for self-inductance measurement.
Heaviside's bridge
for mutual inductance measurement. De Sauty Bridge for capacitance
measurement. Wien's
bridge for capacitance and frequency measurements. Sources of error in
bridge measurements

and precautions. Screening of bridge components. Wagner earth device.
Reference/Suggested Books1. H.S. Kalsi-Electronic Inst. & Measurement;
Tata Mc-Graw Hill
2. Morris-Electrcal Measurements & Instrumentation , ELSEVIER
3. BELL: ELECTRONIC INSTRUMENTATION AND MEASUREMENT Oxford
4. W.D. Cooper-Electronic Inst. & Measurement Techniques; Prentice Hall,
India.
5. A.K. Sawhney-Electrical & Electronic Measurement & Inst; Dhanpat Rai &
Sons.
6. E.W. Golding & F.C. Widdis, “Electrical Measurement & Measuring
Instrument”, A.W.
Wheeler& Co. Pvt. Ltd. India.
7. Forest K. Harries,“Electrical Measurement”,Willey Eastern Pvt. Ltd. India.
3EE6.1 MATHEMATICS
Unit-1 Laplace Transform: Laplace transform with its simple properties,
applications to the solution
of ordinary and partial differential equations having constant coefficients
with special
reference to wave and diffusion equations, digital transforms.
Unit-2 Fourier Transform: Discrete Fourier transform, Fast Fourier transform,
Complex form of
Fourier transform and its inverse applications, Fourier transform for the
solution of partial
differential equations having constant coefficients with special reference to
heat equation and
wave equation.

Unit-3 Fourier Series: Expansion of simple functions in Fourier series, half
range series, change of
interval, harmonic analysis.
Calculus of Variation: Functional, strong and weak variations, simple
variation problems,
Euler’s equation
Unit-4 Complex Variables: Analytic functions, Cauchy–Riemann equations,
Elementary conformal
mapping with simple applications, Line integral in complex domain, Cauchy’s
theorem,
Cauchy’s integral formula.
Unit-5 Complex Variables: Taylor’s series, Laurent’s series, poles, Residues.
Evaluations of simple
definite real integrals using the theorem of residues. Simple contour
integration.
1. M.Ray, J.C. Chaturvedi & H.C. Sharma – Differential Equations. Pub:
Students friends &
company
2. Chandrika Prasad – Mathematics for Engineers, Prasad Mudralaya
3. Bird-Higher Engineering mathematics , ELSEVIER
4. Jeffrey-Advanced Engineering Mathematics , ELSEVIER
5. Chandrika Prasad – Advanced Mathematics for Engineers, Prasad
Mudralaya
6. Ervin Kreyzig - Advanced Engineering Maths, Wiley.
3EE7 POWER ELECTRONICS LAB-I

1 Study the following devices: (i) Analog & digital multimeter (ii) Function/
Signal generators (iii)
Regulated d. c. power supplies (constant voltage and constant current
operations)
2 Study of digital storage CRO and store a transient on it.
3 Study of analog CRO, CRO probes, measurement of time period, amplitude,
frequency & phase
angle using Lissajous figures.
4 Plot V-I characteristic of P-N junction diode & calculate cut-in voltage,
reverse Saturation
current and static & dynamic resistances.
5 Plot V-I characteristic of zener diode and study zener diode as voltage
regulator. Observe the
effect of load changes and determine load limits of the voltage regulator.
6 Plot frequency response curve for audio amplifier and to determine gain
bandwidth product.
7 Plot drain current - drain voltage and drain current – gate bias
characteristics of field effect
transistor and measure of Idss & Vp
8 Plot gain- frequency characteristic of two stages RC coupled amplifier &
calculate its bandwidth
and compare it with theoretical value.
9 Plot gain- frequency characteristic of emitter follower & find out its input
and output resistances. 10 Plot input and output characteristics of BJT in
CB, CC and CE configurations. Find their hparameters.
11 Study half wave rectifier and effects of filters on wave. Also calculate
ripple factor.

12 Study bridge rectifier and measure the effect of filter network on D.C.
voltage output & ripple
factor.
3EE8 COMPUTER PROGRAMMING LAB-I
1 Write a program to find the greatest between four numbers.
2 Write a program to prepare mark sheet of students using structures.
3 Write a C program to read several different names and addresses, re-arrange
the names in
alphabetical order and print name in alphabetical order using structures.
4 Write a program to implement concatenation of two strings using pointers.
5 Write a program to create a singly link list of ten students names and
implement add node, delete
node and isemptylist operations.
6 Write a program to search a pattern in a given string.
7 Write a Program to read add, subtract and multiply integer matrices.
8 Write a program to calculate the power function (m
n
) using the function overloading technique;
implement it for power of integer and double.
9 Implement file creation and operate it in different modes: seek, tell, read,
write and close
operations.
10 Using multiple inheritance, prepare students’ mark sheet. Three classes
containing marks for
every student in three subjects. The inherited class generate mark sheet.

11 Write a program to print the following output using FOR loop.
1 1
2 2 2 2
3 3 3 3 3 3
4 4 4 4 4 4 4 4
5 5 5 5 5 5 5 5 5 5
3EE9 ELECTRICAL CIRCUIT LAB
1 Draw the circuit symbols.
2 Verify theorems for A. C. & D. C. circuits.
PSPICE Programs For Circuit Analysis:
3 DC-analyze resistor networks to determine node voltages, components
voltages, and component
currents.
4 Analyze resistor networks that have several voltage and current sources
and variable load
resistors.
5 Transient –analyze RC & RL circuits to produce tables of component
voltage & current levels
for a given set of time instants & to produce graphs of voltages & currents
versus time.
6 AC-analyze impedance networks to determine the magnitude & phase of
node voltages,
components voltages and component currents.
7 Determine the magnitude & phase and component voltages and currents in
resonant circuits &

produce voltage and current verses frequency graphs.
Programs For Circuit Analysis:
8 Calculate the resistance of a conductor, given its dimensions & resistivity
or determine the
change in conductor resistance when the temp changes.
9 D.C.-analyze resistor networks to determine all junction voltages,
component voltages, and
component currents.10 Transient –analyze RC & RL circuits to produce
tables of component voltage & current levels
for a given set of time instants.
11 Convert Y-connected resistor networks to delta-connected circuits.
3EE10 ELECTRICAL MACHINES LAB-I
1 Speed control of D.C. shunt motor by (a) Field current control method &
plot the curve for speed
verses field current. (b) Armature voltage control method & plot the curve for
speed verses
armature voltage.
2 Speed control of a D.C. Motor by Ward Leonard method and to plot the
curve for speed verses
applied armature voltage.
3 To determine the efficiency of D.C. Shunt motor by loss summation
(Swinburne’s) method.
4 To determine the efficiency of two identical D.C. Machine by Hopkinson’s
regenerative test.
5 To perform O.C. and S.C. test on a 1-phase transformer and to determine
the parameters of its

equivalent circuit its voltage regulation and efficiency.
6 To perform back-to-back test on two identical 1-phase transformers and
find their efficiency &
parameters of the equivalent circuit.
7 To perform parallel operation of two 1-phase transformers and determine
their load sharing.
8 To determine the efficiency and voltage regulation of a single-phase
transformer by direct
loading.
9 To perform OC & SC test on a 3-phase transformer & find its efficiency and
parameters of its
equivalent circuit.
10 To perform parallel operation of two 3-phase transformers and determine
their load sharing.
11 To study the performance of 3-phase transformer for its various
connections, i.e. star/star
star/delta delta/star and delta/delta and find the magnitude of 3
rd
harmonic current.
1. D.R. Kohli & S.K. Jain – A laboratory course in Electrical Machine.
2. S.G. Tarnekar & P.K. Kharbanda – Laboratory courses in Electrical
Engineering
3EE11 ELECTRICAL MEASUREMENT LAB
1 Study working and applications of (i) C.R.O. (ii) Digital Storage C.R.O. & (ii)
C.R.O. Probes

2 Study working and applications of Meggar, Tong-tester, P.F. Meter and
Phase Shifter.
3 Measure power and power factor in 3-phase load by (i) Two-wattmeter
method and (ii) Onewattmeter method.
4 Calibrate an ammeter using DC slide wire potentiometer.
5 Calibrate a voltmeter using Crompton potentiometer.
6 Measure low resistance by Crompton potentiometer.
7 Measure Low resistance by Kelvin's double bridge.
8 Measure earth resistance using fall of potential method.
9 Calibrate a single-phase energy meter by phantom loading at different
power factors.
10 Measure self-inductance using Anderson's bridge.
11 Measure capacitance using De Sauty Bridge.
12 Measure frequency using Wein's bridge.
B. TECH. IV- SEMESTER
4EE1 POWER ELECTRONICS-II
Unit-1 Feedback Amplifiers: Classification, Feedback concept, transfer gain
with feedback.
General characteristics of negative feedback amplifiers. Analysis of voltage
series, voltage shunt, current series and current shunt feedback amplifiers.
Stability criterion.
Unit-2 Oscillators: Classification of oscillators and Criterion for oscillation.
RC-phase shift, Hartley,
Colpitts, tuned collector, Wein Bridge and crystal oscillators. Astable,
monostable and bistable
multivibrators. Schmitt trigger.

Unit-3 OP-AMP and Its Applications: Operational amplifier: inverting and non-inverting
modes.
Characteristics of ideal op-amp. Offset voltage and currents. Basic op-amp
applications.
Differential Amplifier and common mode rejection ratio. Differential DC
amplifier and stable
ac coupled amplifier. Integrator and differentiator. Analog computation,
comparators, sample
and hold circuits, logarithmic & antilog Amplifiers and Analog multipliers.
Unit-4 Integrated Circuits: Precision AC/DC converters-precision limiting,
Precision half wave and
full wave rectifiers. Active average and peak detectors, A to D and D to A
converters. IC 555
timer and its application. Regulated power supplies, Series and shunt voltage
regulators, Brief
idea of Monolithic regulator.
Unit-5 Power Amplifiers: Class –A large signal amplifiers, second harmonic
distortion, higher order
harmonic generation, Transformer coupled audio power amplifier, collector
efficiency.
Pushpull amplifier: Class A, Class B and Class AB operations. Comparison of
performance
with single ended amplifiers.
1. David A. Bell – Electronic Devices and Circuits, 5Ed, Oxford
2. Robert L. Boylested & Louis Nashelshky: Electronic Devices and Circuit
theory (PHI)

3. Millman & Halkias-Electronic Devices& Circuits 2/e, TMH.
4. A.S. Sedra and K.C. Smith “Microelectronics Circuits” Oxford University
Press ( India)
5. R.A. Gayakwad “Op amps and Linear Integrated Circuits” Prentice Hall of
India.
6. Allen Mottershed – Electronic Devices and Circuits, PHI.
7. Salivahanan: Electronic Devices and Circuits 2/e, TMH.
4EE2 DIGITAL ELECTRONICS
Unit-1 Number Systems and Codes: Radix and Radix conversions, sign,
magnitude & complement
notation. Weighted and non-weighted codes, BCD codes, self-complementing
codes, cyclic
codes, error detecting and correcting codes, ASCII & EBCDIC codes.
Alphanumeric codes.
Fixed point and floating point arithmetic. BCD arithmetic.
Unit-2 Boolean Algebra and Digital Logic Gates: Features of Boolean algebra,
postulates of
Boolean algebra, theorems of Boolean algebra. Fundamental logic gates,
derived logic gates,
logic diagrams and Boolean expressions. Converting logic diagrams to
universal logic.
Positive, negative and mixed logic. Minimization Techniques: Minterm,
Maxterm,
Karnaugh’s maps, simplification of logic functions with K-map, conversions
of truth tables in
SOP & POS forms, incompletely specified functions, variable mapping, Quinn-
Mcklusky

method.
Unit-3 Switching Circuits And Logic Families: Diode, BJT, FET as switch.
Different types of logic
families: RTL, TTL, open collector TTL, three state output logic, TTL
subfamilies, MOS,
CMOS, ECL IIL.
Unit-4 Combination Systems: Combinational logic circuit design, Half and full
adder & subtractors.
Binary serial and parallel adders, BCD adder. Binary multiplier, comparator,
decoders,
encoders, multiplexer, de-multiplexer, Code converters.
Unit-5 Sequential Systems: Latches, Flip-Flop: R-S, D, J-K, T, Master slave.
Flip-flop conversions.
Counters: asynchronous & synchronous counter. Counter design, counter
applications.
Registers: buffer & shift register.
1. T.M. Floyd, R.P. Jain-Digital fundamentals, Pearson Education.
2. Morris and Mano - Digital logic and Computer Design, Prentice – Hall of
India
3. R.P. JAIN:Modern Digital Electronics 4/e, TMH.4. Kharate G K : Digital
Electronics, Oxford
5. Pedroni -Digital Electronics & Design , ELSEVIER.
6. Balbir Kumar and Shail B.Jain, “Electronic Devices and Circuits” PHI, 2007.
7. Anil K. Maini, “Digital Electronics: Principles and Integrated circuits” Wiley
2008.

8. Anand Kumar, “Switching Theory and Logic Design” Prentice Hall of India,
2008.
4EE3 ELECTRICAL MACHINES-II
Unit-1 Introduction: General equation of inducted emf, AC armature windings:
concentric and
distributed winding, chording, skewing, effect on induced emf. Armature and
field mmf, effect
of power factor and current on armature mmf, harmonics. Rotating fields.
Unit-2 Induction Motors: Construction of squirrel cage & slip ring induction
motor, basic principles,
flux and mmf waves, induction motor as a transformer. Equivalent circuits,
torque equation,
torque-slip curves, no load & block rotor tests, circle diagram, performance
calculation. Effect
of rotor resistance. Cogging, Crawling. Double cage squirrel cage induction
motor, induction
generator, induction regulator.
Unit-3 Starting & Speed Control of Induction Motors: Various methods of
starting & speed
control of squirrel cage & slip ring motor, cascade connection, braking.
Single-Phase Induction Motor: Revolving field theory, starting methods,
equivalent circuits.
Unit-4 Synchronous Generator: Construction, types, excitation systems,
principles. Equation of
induced emf, flux and emf waves, theory of cylindrical rotor and salient pole
machines, tworeactance theory, phasor diagrams, power developed, voltage
regulation, OC & SC tests, zero

power factor characteristics, potier triangle and ASA method of finding
voltage regulation,
synchronization, parallel operation, hunting and its prevention.
Unit-5 Synchronous Motors: types, construction, principle, phasor diagrams,
speed torque
characteristics, power factor control, V-curves, starting methods,
performance calculations,
applications, synchronous condenser, synchronous induction motor.
1. A.E. Fitggerald, C.Kingsley Jr and Umans,”Electric Machinery” 6th Edition
McGraw Hill,
International Student Edition.
2. Kothari & Nagrath: Electric Machines 3/e,TMH
3. M.G. Say, “The Performance and Design of AC machines”, Pit man & Sons.
4. Guru: ELECTRIC MACHINERY 3E, Oxford
5. P.S. Bimbhra-Electrical Machinery, Khanna Pub.
6. Stephen J Chapman: Electric Machinery Fundamentals, McGraw-Hill
7. Husain Ashfaq ,” Electrical Machines”, Dhanpat Rai & Sons
8. Irving L.Kosow, “Electric Machine and Tranformers”, Prentice Hall of India.
4EE4 COMPUTER PROGRAMMINNG-II
Unit-1 UNIX- Introduction to following basic commands (excluding shell
programming): who, touch,
cat, cp, rm, mv, ls, unmask, pwd, mkdir, rmdir, bc, expr, factor, logname, id,
uname, try, date,
banner, dspace, du, ulimit, passwd, cal, wc, sort, cut, grep, dd, head, pg, lp,
tail, compress,

man, tee.
Unit-2 VI Editor: Text entry and command modes, cursor movement
commands, string replacement
commands and set commands.
Unit-3 JAVA: Variation from C++ to JAVA. Introduction to JAVA bytecode,
virtual machine,
application, application & applets of Java, integer, floating point, characters,
Boolean, literals,
and array declarations.
Unit-4 Operators and Control Statements: Arithmetic operators, bitwise
operators, relational
operators, Boolean logic operators, the assignment operators, ?: operators,
operator
precedence. Switch and loop statements.
Unit-5 Package and Interfaces: Packages, access protection, importing &
defining packages.
Defining and implementing interfaces. I/O APPLETS: I/O basics, reading
console I/O, input and print stream classes, applet fundamental and string
handling, mouse and keyboard
interfaces, awt tools and controls.
1. Yashwant Kanithkar: Unix & Shell Programming (BPB)
2. Sumitabha Das: Unix: Concepts & Applications 4/e (TMH)
3. Balagurusamy: Programming with Java 4/e (TMH)
4. Grady Booch – Object Oriented Analysis & Design with Applications
(Pearson Education,

Patrick.
5. Naughton, Herbert Schildt – Java 2: The complete Reference (McGraw-Hill,
3rd Ed.)
6. James Rambaugh - Object Oriented Modelling and Design (PHI, IGNOU Ed.)
& Pearson
4EE5 CIRCUIT ANALYSIS-II
Unit-1 Impedance and Admittance Functions: The concept of complex
frequency, transform
impedance and admittance, series and parallel combinations.
Network Functions: Terminals and terminal pairs, driving point impedance
transfer functions,
poles and zeros. Restrictions on pole and zero location in s-plane. Time
domain behavior from
pole and zero plot. Procedure for finding network functions for general two
terminal pair
networks.
Unit-2 Network Synthesis: Hurwitz polynomial, positive real functions,
reactive networks.
Separation property for reactive networks. The four-reactance function
forms, specification for
reactance function. Foster form of reactance networks. Cauer form of
reactance networks.
Synthesis of R-L and R-C networks in Foster and Cauer forms.
Unit-3 Two Port General Networks: Two port parameters (impedance,
admittance, hybrid, ABCD
parameters) and their inter relations. Equivalence of two ports. Transformer
equivalent, inter

connection of two port networks. The ladder network, image impedance,
image transfer
function, application to L-C network, attenuation and phase shift in
symmetrical T and pi
networks.
Unit-4 Two Port Reactive Network (Filters): Constant K filters. The m-derived
filter. Image
impedance of m-derived half (or L) sections, composite filters. Band pass and
band
elimination filters. The problem of termination, lattice filters, Barlett’s
bisection theorem.
Introduction to active filters.
Unit-5 Coupled Circuits: Conductively coupled circuits. Mutual impedance,
magnetic coupling,
mutual inductance, co-efficient of magnetic coupling, circuit directions and
sign of mutual
inductance, mutual inductance between portions of the same circuit, mutual
inductance
between parallel branches, transferred impedance. Transformer equivalent
inductively and
conductively coupled circuits; Resonance in Single tuned and Double tuned
circuits, effect of
coefficient of coupling.
1. M.E. Van Valkenburg, “An Introduction to Modern Network
Synthesis”,Wiley Eastern
2. Nagsarkar & Sukhija : Circuits & Networks, Oxford

3. Choudhary D.Roy, “Network & Systems”, Wiley Eastern Ltd.
4. Ghosh & Chakrabarti: Network Analysis and Synthesis (TMH)
5. Samarajit Ghosh, “Network Theory: Analysis and Synthesis” Prentice Hall
of India, 2008
6. A.Chakrabarti, “Circuit Theory” Dhanpat Rai & Co.
7. Umesh Sinha, Transmission Lines and Networks, Satya prakashan.
8. Murthy and Kamath, Basic Circuit Analysis, Jaico Publishing House.
4EE6.1 ADVANCED MATHEMATICS
Unit-1 Numerical Analysis: Finite differences - Forward backward and central
difference. Newton’s
forward and backward differences interpolation formulae. Sterling’s
formulae, Lagrange’s
interpolation formula. Solution of non-linear equations in one variable by
Newton Raphson
and Simultaneous algebraic equation by Gauss and Regula Falsi method.
Solution of simultaneous equations by Gauss elimination and Gauss Seidel
methods. Fitting of curves
(straight line and parabola of second degree) by method of least squares.
Unit-2 Numerical Analysis: Numerical differentiation, numerical integration
trapezoidal rule,
Simpson’s one-third and one eighth rule. Numerical Integration of ordinary
differential
equations of first order, Picard’s method, Euler’s & modified Euler’s methods.
Miline’s
method and Runga Kutta fourth order method. Simple linear difference
equations with
constant coefficients.

Unit-3 Special Functions: Bessel’s function of first and second kind, simple
recurrence relations,
orthogonal property of Bessel functions, Transformation, Generating
functions, Legendre’s
function of first kind, simple recurrence relations, orthogonal property,
Generating functions.
Unit-4 Statistics & Probability: Elementary theory of probability, Baye’s
theorem with simple
applications, Expected value. Theoretical probability distributions – Binomial,
Poisson and
Normal distributions.
Unit-5 Statistics & Probability: Lines of regression, co-relation and rank
correlation. Transforms:
Z-transforms, its inverse, simple properties and application to difference
equations.
1. Jeffrey-Advanced Engineering Mathematics , ELSEVIER
2. Ervin Kreyzig - Advanced Engineering Maths, John Wiley
3. Bird-Higher Engineering Mathematics , ELSEVIER
4. Chandrika Prasad – Advanced Mathematics for Engineers, Prasad
Mudralaya
5. Kaplan, W. “Advanced Mathematics for Engineers”, Addison-Wesley
Publishing Co.
6. Brigham, E.O. “The Fast Fourier Transform and its Applications”, Prentice-
Hall
7. J.N. Kapur, Mathematical Statistics, S. Chand & company Ltd.,2000

8. R.K. Jain & S.R.K. Iyenger, Advance Engineering Mathematics, Narosa
Pub., 2002.
9. E. Kreysig, Advanced Engineering Mathematics, John Wiley & Sons, 2005.
4EE7 POWER ELECTRONICS LAB-II
1 Plot gain-frequency characteristics of BJT amplifier with and without
negative feedback in the
emitter circuit and determine bandwidths, gain bandwidth products and
gains at 1KHz with and
without negative feedback.
2 Study of series and shunt voltage regulators and measure line and load
regulation and ripple
factor.
3 Plot and study the characteristics of small signal amplifier using FET.
4 Push Pull amplifier: To study variation of output power & distortion with
load.
5 Study Wein bridge oscillator and observe the effect of variation in R & C on
oscillator frequency
6 Study transistor phase shift oscillator and observe the effect of variation in
R & C on oscillator
frequency and compare with theoretical value.
7 Study the following oscillators and observe the effect of variation of C on
oscillator frequency:
(i) Hartley (ii) Colpitts
8 (i) Study op-amp in inverting and non-inverting modes. (ii) Use op-amp as
scalar, summer and
voltage follower.

9 Use of op-amp as differentiator and integrator.
10 Study Op-amp characteristics and get data for input bias current, measure
the output-offset
voltage and reduce it to zero and calculate slow rate.
11 Obtain a frequency response of filters.
12 Analyze filter circuits to produce voltage frequency & phase-frequency
response graphs using
PSPICE.
4EE8 DIGITAL ELECTORNICS LAB
1 Study of following combinational circuits: Multiplexer, Demultimplexer and
Encoder. Verify truth tables of various logic functions.
2 Study of various combinational circuits based on: AND/NAND Logic blocks
and OR/NOR
Logic blocks.
3 To study various waveforms at different points of a transistor bistable
multivibrator and its
frequency variation with different parameters.
4 To design a frequency divider using IC-555 timer.
5 To study various types of registers and counters.
6 To study Schmitt trigger circuit.
7 To study transistor astable multivibrator.
8 Experimental study of characteristics of CMOS integrated circuits.
9 Interfacing of CMOS to TTL and TTL to CMOS.
10 BCD to binary conversion on digital IC trainer.
11 Testing of digital IC by automatic digital IC trainer.

12 To study OP-AMP as Current to Voltage & Voltage to Current converters &
comparator.
4EE09 ELECTERICAL MACHINES LAB-II
1 Separation of transformer core losses and to determine the hystersis and
eddy current losses at
rated voltage and frequency.
2 To plot the O.C.C. & S.C.C. of an alternator and to determine its regulation
by synchronous
impedance method.
3 To synchronize an alternator across the infinite bus (RSEB) & summarize
the effects of variation
of excitation on load sharing.
4 To plot the V-curve for a synchronous motor for different values of loads.
5 To perform sumpner’s back-to-back test on 3 phase transformers, find its
efficiency &
parameters for its equivalent circuits.
6 To perform the heat run test on a delta/delta connected 3-phase
transformer and determine the
parameters for its equivalent circuit.
7 To perform no load and blocked rotor test on a 3 phase induction motor and
to determine the
parameters of its equivalent circuits. Draw the circle diagram and compute
the following (i)
Max. Torques (ii) Current (iii) slip (iv) p.f. (v) Efficiency.
8 To perform the load test on a 3-phase induction motor and determine its
performance

characteristics (a) Speed vs load curve (b) p.f. vs load curve (c) Efficiency vs
load curve (d)
Speed vs torque curve
9 Determination of losses and efficiency of an alternator.
10 To find Xd and Xq of a salient pole synchronous machine by slip test.
1. D.R. Kohli & S.K. Jain – A Laboratory Course in Electrical Machines,
Publisher: NEM
CHAND & BROTHERS.
2. S.G. Tarnekar & P.K. Kharbanda – Laboratory Course in Electrical
Engineering , S. Chand
4EE10 COMPUTER PROGRAMMING LAB - II
UNIX
1 Use of advanced vi commands.
2 Sorting of files containing records using sort command.
3 Searching patterns in files.
4 Use of bc, expr, factor commands.5 Use of head, tail, compress commands.
6 Memory management commands, dfspace, du, ulimit etc.
JAVA
7 Programs based on matrix: addition, multiplication, transpose, check if
matrix is symmetric /
upper triangular / lower triangular / unit matrix.
8 Representation of complex numbers and their operation: add, multiply;
divide, subtraction,
magnitude (mod) etc.

9 Complex matrix representation and operation: add, subtract, multiply.
10 Defining packages for sorting algorithms.
11 File handling operations: input from file, output to file, file copy, file
concatenation.
12 Mouse and keyboard event handling programs.
13 Programs based on string operations.
14 Drawing in applet and use of buttons check boxes, text fields and labels
in applets.
4EE11 HUMANITIES & SOCIAL SCIENCES
Unit-1 India: Brief history of Indian Constitution, farming features,
fundamental rights, duties,
directive principles of state. History of Indian National Movement, socio
economic growth
after independence.
Unit-2 Society: Social groups- concept and types, socialization- concept and
theory, social control:
concept, social problem in contemporary India, status and role.
Unit-3 The Fundamentals of Economics: meaning, definition and importance
of economics, Logic
of choice, central economic problems, positive and normative approaches,
economic systemssocialism and capitalism.
Unit-4 Microeconomics: Law of demand supply, utility approach, indifference
curves, elasticity of
demand and supply and applications, consumer surplus, Law of returns to
factors and returns
to scale.

Unit-5 Macroeconomics: concepts relating to National product–National
income and its
measurement, Simple Keynesian theory, simple multiplier, money and
banking. Meaning,
concept of international trade, determination of exchange rate, Balance of
payments.
B. TECH. V- SEMESTER
5EE1 POWER ELECTRONICS-III
Unit-1 Power Semiconductor Devices: Characteristics of Power Transistor,
Thyristor, GTO, Power
MOSFET and IGBT. Two-Transistor Model of Thyristor.
Unit-2 SCR: Construction and characteristics, specification and ratings, pulse
transformer, optical
isolators, methods of turn on: R, RC, UJT relaxation oscillator, Rating
extension by series and
parallel connections, string efficiency. Protection of SCR-Protection against
over voltage, over
current, dv/dt, di/dt, Gate protection.
Unit-3 Converters-I: Single Phase half & full wave converters with RL load,
Single phase dual
converters, Three phase half wave converters, Three phase full converters
with RL load, Three
phase dual converters.
Unit-4 Converters-II: Single and three-phase semi converters with RL load.
Power Factor
Improvement-Extinction angle control, symmetrical angle control, pulse
width modulation

control and sinusoidal pulse width modulation control. Inversion operation.
Effect of load and
source impedances.
Unit-5 DC-DC Converters: Choppers: Step Up/Down Copper, Chopper
Configurations, analysis of
type A Chopper Commutation of Choppers. Switched Mode Regulators-buck,
boost, buck-boost
and cuk regulator.Reference/Suggested Books
1. M H Rashid: Power Electronics, Circuits Devices and Applications, PHI
2. Ned Mohan: Power Electronics, John Wiley
3. M D Singh and K B Khanchandani: Power Electronics 2/e, TMH, 2008.
4. Krein P. T: Eleements of Power Electronics, Oxford.
5. P C Sen: Power Electronics, Tata McGraw-Hill, India.
6. C W Lander: Power Electronics, McGraw Hill
7. W Shepherd: Power Electronics and Motor Control, Cambridge Uni. Press.
8. P S Bimbhra: Power Electronics, Khanna Publishers.
5EE2 MICROPROCESSORS & COMPUTER ARCHITECTURE
Unit-1 Introduction: CPU, address bus, data bus and control bus. Input/Output
devices, buffers,
encoders, latches and memories. Brief introduction to comparison of
different features in 8085
and 8086 microprocessors.
Unit-2 8085 Microprocessor Architecture: Internal Data Operations and
Registers, Pins and Signals,
Peripheral Devices and Memory Organization, Interrupts.

Unit-3 8085 Microprocessor Instructions: Classification, Format and Timing.
Instruction Set.
Programming and Debugging, 8 Bit And 16 Bit Instructions.
Unit-4 8085 Microprocessor Interfacing: 8259, 8257, 8255, 8253, 8155 chips
and their applications.
A/D conversion, memory, keyboard and display interface (8279).
Unit-5 Basic Computer Architecture: Central Processing Unit, memory and
input/output interfacing.
Memory Classification: Volatile and non-volatile memory, Primary and
secondary memory,
Static and Dynamic memory, Logical, Virtual and Physical memory. Types of
memory:
Magnetic core memory, binary cell, Rom architecture and different types of
ROM, RAM
architecture, PROM, PAL, PLA, Flash and Cache memory, SDRAM, RDRAM
and DDRAM.
Memory latency, memory bandwidth, memory seek time.
1. Gaonkar, Ramesh S, “Microprocessor Architecture, programming and
applications with the
8085” Pen ram International Publishing 5th Ed.
2. Douglas Hall: Microprocessors and Interfacing, Revised Second Edition
(SIE) TMH
3. Mathur A P -Introduction to Microprocessors , TMH
4. Ray, A.K. & Burchandi, K.M., “Advanced Microprocessors and Peripherals:
Architecture,
Programaming and Interfacing” Tata Mc. Graw Hill.

5. Krishna Kant, “Microprocessors and Microcontrollers” PHI Learning.
6. Brey, Barry B. “INTEL Microprocessors” Prentice Hall ( India)
7. M. Rafiquzzaman, “Microprocessors- Theory and applications” PHI
8. B. Ram, “Advanced Microprocessor & Interfacing” Tata McGraw Hill
9. Liu and Gibson G.A., “Microcomputer Systems: The 8086/8088 Family” PHI
5EE3 CONTROL SYSTEMS
Unit-1 Introduction: Elements of control systems, concept of open loop and
closed loop systems.,
Examples and application of open loop and closed loop systems, brief idea
of multivariable
control systems.
Unit-2 Mathematical Modeling of Physical Systems: Representation of
physical system (Electro
Mechanical) by differential equations, Determination of transfer function by
block diagram
reduction techniques and signal flow method, Laplace transformation
function, inverse Laplace
transformation.
Unit-3 Time Response Analysis of First Order and Second Order System:
Characteristic equations,
response to step, ramp and parabolic inputs, transient response analysis,
steady state errors and
error constants, Transient & steady state analysis of LTI systems.
Unit-4 Stability of the System: Absolute stability and relative stability,
Routh’s stability criterion,

root locus method of analysis, polar plots, Nyquist stability criterion. M and N
Loci, Nichols chart.
Unit-5 Elementary Ideas of Compensation, Networks: Lag, lead and log lead
networks, brief idea of
proportional, derivative and integral controllers.
1. I J Nagrath and M Gopal: Control Systems Engineering, 3rd Ed, New Age
Publication.
2. Robert H Bishop : Modern Control Systems, Boyd and Fraser pub
3. B C Kuo: Modern Control Engineering, NEW AGE
4. K.Ogata,“Modern Control Engineering” Prentice Hall of India.
5. Norman S.Nise, “Control System Engineering”, John Wiley & Sons.
6. Richard C Dorf, Robert H Bishop : Modern Control Systems, Prentice-Hall
5EE4 GENERATION OF ELECTRICAL POWER
Unit-1 Conventional Energy Generation Methods: (i) Thermal Power plants:
Basic schemes and
working principle. (ii) Gas Power Plants: open cycle and closed cycle gas
turbine plants,
combined gas & steam plants – basic schemes. (iii) Hydro Power Plants:
Classification of
hydroelectric plants. Basic schemes of hydroelectric and pumped storage
plants. (iv) Nuclear
Power Plants: Nuclear fission and Nuclear fusion. Fissile and fertile
materials. Basic plant
schemes with boiling water reactor, heavy water reactor and fast breeder
reactor. Efficiencies of

various power plants.
Unit-2 New Energy Sources: Impact of thermal, gas, hydro and nuclear power
stations on
environment. Green House Effect (Global Warming). Renewable and non-renewable
energy
sources. Conservation of natural resources and sustainable energy systems.
Indian energy scene.
Introduction to electric energy generation by wind, solar and tidal.
Unit-3 (i) Loads and Load curves: Types of load, chronological load curve,
load duration curve,
energy load curve and mass curve. Maximum demand, demand factor, load
factor, diversity
factor, capacity factor and utilization. (ii) Power factor improvement:
Causes and effects of
low power factor and advantages of power factor improvement. Power
factor improvement
using shunt capacitors and synchronous condensers.
Unit-4 Power Plant Economics: (i) Capital cost of plants, annual fixed and
operating costs of plants,
generation cost and depreciation. Effect of load factor on unit energy cost.
Role of load diversity
in power system economics. (ii) Calculation of most economic power factor
when (a) kW
demand is constant and (b) kVA demand is constant. (iii) Energy cost
reduction: off peak
energy utilization, co-generation, and energy conservation.
Unit-5 (i) Tariffs: Objectives of tariffs. General tariff form. Flat demand rate,
straight meter rate, block

meter rate. Two part tariff, power factor dependent tariffs, three-part tariff.
Spot (time
differentiated) pricing. (ii) Selection of Power Plants: Comparative study of
thermal, hydro,
nuclear and gas power plants. Base load and peak load plants. Size and
types of generating
units, types of reserve and size of plant. Selection and location of power
plants.
1. B.R. Gupta - Generation of Electrical Energy Wheelar Pub
2. Soni, Gupta and Bhatnagar - Generation of Electrical Power. Dhanpat Rai
Pub
3. S. L. Uppal - Electrical Power. Khanna Pub
4. M. V Deshpande: Elements of Electrical Power Station Design, Wheeler
Publishing Co.
5EE5 TRANSMISSION & DISTRIBUTION OF ELECTRICAL POWER
Unit-1 (i) Supply systems: - Basic network of power system. Transmission
and distribution voltage,
effect of system voltage on size of conductor and losses. Comparison of DC
2- wire, DC 3-
wire, 1- phase AC and 3- phase AC (3- wire and 4- wire) systems. (ii)
Distribution Systems: -
Primary and secondary distribution systems, feeder, distributor and service
mains. Radial and
ring- main distribution systems. Kelvin’s law for conductor size.
Unit-2 Mechanical features of overhead lines:- Conductor material and types
of conductor.

Conductor arrangements and spacing. Calculation of sag and tension,
supports at different levels, effect of wind and ice loading, stringing chart
and sag template. Conductor vibrations
and vibration dampers.
Unit-3 Parameters of Transmission Lines: Resistance inductance and
capacitance of overhead lines,
effect of earth, line transposition. Geometric mean radius and distance.
Inductance and
capacitance of line with symmetrical and unsymmetrical spacing Inductance
and capacitance of
double circuit lines. Skin and proximity effects.
Equivalent circuits and performance of short and medium transmission lines.
Unit-4 (i)Generalized ABCD line constants, equivalent circuit and
performance of long transmission
line. Ferranti effect. Interference with communication circuits. Power flow
through a
transmission line (ii) Corona: Electric stress between parallel conductors.
Disruptive critical
voltage and visual critical voltage, Factors affecting corona. Corona power
loss. Effects of
corona.
Unit-5
(i) Insulators: Pin, shackle, suspension, post and strain insulators. Voltage
distribution across
an insulator string, grading and methods of improving string efficiency. (ii)
Underground
Cables: Conductor, insulator, sheathing and armoring materials. Types of
cables. Insulator

resistance and capacitance calculation. Electrostatic stresses and reduction
of maximum stresses.
Causes of breakdown. Thermal rating of cable. Introduction to oil filled and
gas filled cables.
1. A S Pabla: Electric Power Distribution. (TMH)
2. B R Gupta: Power System Analysis & Design, S. CHAND PUBLISHERS
3. Soni, Gupta and Bhatnagar: A Course in Electrical Power, Dhanpat Rai
4. C.L. Wadhwa: Electrical Power Systems, New Age
5. Nagrath Kothari: Modern Power System Analysis. (TMH)
6. J. J. Grainger& W. D. Stevenson: Power System Analysis (TMH).
7. Kamaraju: Electrical Power Distribution Systems (TMH)
5EE 6.1 ADVANCED DISTRIBUTION SYSTEM
Unit-1 (i) Distribution Systems: Distribution of power, future distribution
systems, power loads. (ii)
Load Forecasting: Introduction, load survey, load forecasting-regression
analysis, correlation
theory, analysis of time series, load growth factors, sources of error.
Unit-2 Operation: Operation criterion and standards: Voltage control –
voltage regulation, kVA – km
conductor loading, correction of system voltage. Harmonics – introduction,
effects of harmonics
on networks, limits of harmonics, filters. Load variations- causes of voltage
fluctuations,
measures to reduce flickering. Ferro resonance. System losses -
introduction, losses in

components, measurement of losses, reduction of losses. Energy
management.
Unit-3 Distribution Power Capacitors: Reactive power flow, monitoring and
compensation in
distribution system, maintaining system voltage. Series and shunt
capacitors, comparison. Shunt
capacitors in distribution system - LT and HT shunt capacitors, capacitor
rating for power factor
improvement, constructional features. System harmonics.
Unit-4 Grounding: Grounding system, earth and safety, earth electrode- earth
resistance calculation,
effect of rod size and soil resistivity, earth conductor sizes. Introduction to
earth electrode
design. Brief description of system earthing – system neutral earthing,
earthing of substations,
lines and consumer premises. Earth fault protection of feeders.
Unit-5 Distribution Automation: Introduction to distribution automation.
Concept of communicationpower line carrier, radio communication, fibre
optics, satellite communication and sensors.
Introduction to supervisory control and data acquisition (SCADA). Brief
descriptor of an
automation system.
1. A S Pabla: Electric Power Distribution. (TMH)
2. B R Gupta: Power System Analysis & Design, S. CHAND PUBLISHERS
3. Nagrath Kothari: Modern Power System Analysis. (TMH)4. J. J. Grainger&
W. D. Stevenson: Power System Analysis (TMH).

5. Kamaraju: Electrical Power Distribution Systems (TMH)
5EE6.2 PRINCIPLE OF COMMUNICATION SYSTEMS
Unit-1 Noise Effects in Communication Systems: Resistor noise, Networks
with reactive elements,
Noise temperature, Noise bandwidth, effective input noise temperature,
Noise figure. Noise
figure & equivalent noise temperature in cascaded circuits.
Unit-2 Amplitude Modulation: Frequency translation, Recovery of base band
signal, Spectrum &
power relations in AM systems. Methods of generation & demodulation of
AM-DSB, AMDSB/SC and AM-SSB signals. Modulation & detector circuits for
AM systems. AM
transmitters & receivers.
Unit-3 Frequency Modulation: Phase & freq. modulation & their relationship,
Spectrum & bandwidth
of a sinusoidally modulated FM signal, phasor diagram, Narrow band & wide
band FM.
Generation & demodulation of FM signals. FM transmitters & receivers,
Comparison of AM,
FM & PM. Pre emphasis & de-emphasis. Threshold in FM, PLL demodulator.
Unit-4 Noise in AM and FM: Calculation of signal-to-noise ratio in SSB-SC,
DSB-SC, DSB with
carrier, Noise calculation of square law demodulator & envelope detector.
Calculation of S/N
ratio in FM demodulators, Super-heterodyne receivers.
Unit-5 Pulse Modulation Systems: Sampling theorem, Generation and
demodulation methods of

PAM, PWM, PPM.
1. Taub and Schilling: Principles of Communication Systems 3/e, TMH
2. B P Lathi : Modern Analog & Digital Communication System, Oxford
University Press
3. Simon Hykin: Communication Systems, John Wiley and Sons
4. R P Singh and S D Sapre: Communication System Analog & Digital 2/e.
(TMH)
5. G. Kennedy and B. Davis , “Electronic Communication Systems” Tata
McGraw Hill
6. Roy Blake, “ Wireless Communication Technology” Thomson Asia Pvt. Ltd.
Singapore
5EE6.3 INTRODUCTION TO VLSI
Unit-1 Introduction to MOS Technology: Basic MOS transistors, Enhancement
Mode transistor
action, Depletion Mode transistor action, NMOS and CMOS fabrication.
Unit-2 Basic Electrical Properties of MOS Circuits: Ids versus Vds
relationship, Aspects of threshold
voltage, Transistor Transconductance gm. The nMOS inverter, Pull up to Pull-down
ratio for a
NMOS Inverter and CMOS Inverter (Bn/Bp), MOS transistor circuit Model,
Noise Margin.
Unit-3 CMOS Logic Circuits: The inverter, Combinational Logic, NAND Gate
NOR gate, Compound
Gates, 2 input CMOS Multiplexer, Memory latches and registers,
Transmission Gate, Gate
delays, CMOS-Gate Transistor sizing, Power dissipation.

Unit-4 Basic Physical Design of Simple Gates and Layout Issues: Layout
issues for inverter, Layout
for NAND and NOR Gates, Complex Logic gates Layout, Layout optimization
for performance.
Unit-5 Introduction to VHDL, Verilog & other design tools. VHDL Code for
simple Logic gates, flipflops, shift-registers, Counters, Multiplexers, adders
and subtractors.
1. S M Sze: VLSI Technology (TMH)
2. SM KANG:CMOS Digital Integrated Circuits, TMH
3. Stephen A Compbell: The Science & Engineering of Microelectronic
Fabrication, Oxford.
4. James D Plummer, Micheal Deal & Petter B Griffin: Silicon VLSI Tech.
Fundamental,
Practice & Modeling, Prentice Hall.
5EE7 POWER ELECTRONICS LAB-III
1 Study the comparison of following power electronics devices regarding
ratings, performance
characteristics and applications: Power Diode, Power Transistor, Thyristor,
Diac, Triac, GTO,
MOSFET, MCT and SIT. 2 Determine V-I characteristics of SCR and measure
forward breakdown voltage, latching and
holding currents.
3 Find V-I characteristics of TRIAC and DIAC.
4 Find output characteristics of MOSFET and IGBT.
5 Find transfer characteristics of MOSFET and IGBT.

6 Find UJT static emitter characteristics and study the variation in peak
point and valley point.
7 Study and test firing circuits for SCR-R, RC and UJT firing circuits.
8 Study and test 3-phase diode bridge rectifier with R and RL loads. Study the
effect of filters.
9 Study and obtain waveforms of single-phase half wave controlled rectifier
with and without
filters. Study the variation of output voltage with respect to firing angle.
10 Study and obtain waveforms of single-phase half controlled bridge
rectifier with R and RL
loads. Study and show the effect of freewheeling diode.
11 Study and obtain waveforms of single-phase full controlled bridge
converter with R and RL
loads. Study and show rectification and inversion operations with and
without freewheeling
diode.
12 Control the speed of a dc motor using single-phase half controlled bridge
rectifier and full
controlled bridge rectifier. Plot armature voltage versus speed
characteristics.
1. O P Arora: Power Electronics Laboratory-Experiments and Organization,
Narosa Pub.
2. P B Zbar: Industrial Electronics- A Text-Lab Manual, Tata McGraw Hill
5EE8 MICROPROCESSOR LAB
1 Study the hardware, functions, memory structure and operation of 8085-
Microprocessor kit.

2 Program to perform integer division: (1) 8-bit by 8-bit (2) 16 bit by 8 bit.
3 Transfer of a block of data in memory to another place in memory
4 Transfer of black to another location in reverse order.
5 Searching a number in an array.
6 Sorting of array in: (1) Ascending order (2) Descending order.
7 Finding party of a 32-bit number.
8 Program to perform following conversion (1) BCD to ASCII (2) BCD to
hexadecimal.
9 Program to multiply two 8–bit numbers
10 Program to generate and sum 15 Fibonacci numbers.
11 Program for rolling display of message “India”, “HELLO”.
12 To insert a number at correct place in a sorted array.
13 Reversing bits of an 8-bit number.
14 Fabrication of 8-bit LED interfaces for 8085 kit through 8155 and 8255.
15 Data transfer on output port 8155 & 8255 & implementation of disco light,
running light, and
sequential lights on the above mentioned hardware.
16 Parallel data transfer between two DYNA-85 kit using 8253 ports.
17 Generation of different waveform on 8253/8254 programmable timer.
5EE9 MATLAB PROGRAMMING LAB
1 Basics of MATLAB matrices and vectors, matrix and array operations,
Saving and loading data,
plotting simple graphs, scripts and functions, Script files, Function files,
Global Variables,

Loops, Branches, Control flow, Advanced data objects, Multi-dimensional
matrices, Structures, Applications in linear algebra curve fitting and
interpolation. Numerical integration, Ordinary
differential equation. (All contents is to be covered with tutorial sheets)
2 Simulink: Idea about simulink, problems based on simulink. (All contents is
to be covered with
tutorial sheets)
1. Almos Gilat, “MATLAB: An Introduction with Applications” Wiley India Ltd.,
2004.
5EE10 POWER SYSTEM DESIGN
1 Generating station design: Design considerations and basic schemes of
hydro, thermal, nuclear
and gas power plants. Electrical equipment for power stations,
2 Auxiliary power supply scheme for thermal power plant.
3 Distribution system Design: Design of feeders & distributors. Calculation of
voltage drops in
distributors. Calculation of conductor size using Kelvin’s law.
4 Methods of short term, medium term and long term load forecasting.
5 Sending end and receiving end power circle diagrams.
6 Instrument Transformers: Design considerations of CTs & PTs for
measurement and protection.
7 Substations: Types of substations, various bus–bar arrangements.
Electrical equipment for
substations.
5EE11 ENTREPRENEURSHIP DEVELOPMENT

1 Definition of entrepreneur, qualities of a successful entrepreneur, Charms
of being an
entrepreneur, achievement- motivation, leadership and entrepreneurial
competencies.
2 Decision-making, procedures and formalities for starting own business,
financial support
system.
3 Identification and selection of business opportunities and market survey,
business plan.
Implementation and customer satisfaction.
4 Business crises, problem-solving attitude, communication skill.
Government policies for
entrepreneurs.
5 Knowledge based enterprises, Scope of entrepreneur in present context,
area of future
entrepreneurship.
6 Marketing & Sales Promotion, Techno-Economic Feasibility Assessment by
Preparation of
Preliminary & Detailed project report.
B. TECH. VI- SEMESTER
6EE1 MODERN CONTROL THEORY
Unit-1 Introduction: Concept of Linear vector space Linear Independence,
Bases & Representation,
domain and range. Concept of Linearity, relaxedness, time invariance,
causality.
Unit-2 State Space Approach of Control System Analysis: Modern Vs
conventional control theory,

concept of state, state variable state vector, state space, state space
equations, Writing statespace equations of mechanical, Electrical systems,
Analogous systems.
Unit-3 State Space Representation using physical and phase variables,
comparison form of system
representation. Block diagram representation of state model. Signal flow
graph representation.
State space representation using canonical variables. Diagonal matrix.
Jordan canonical form,
Derivation of transfer functions from state-model.
Unit-4 Solution of State Equations: Diagonalization, Eigenvalues and eigen
vectors. Matrix
exponential, State transition matrix, Properties of state transition matrix.
Computation of State
transition matrix concepts of controllability & observability. Pole placement
by state feedback,
Ackerman’s formulaUnit-5 Digital Control Systems: Introduction, sampled
data control systems, signal reconstruction,
difference equations. The z-transform, Z-Transfer Function. Block diagram
analysis of
sampled data systems, z and s domain relationship, digital PID controller
1. I J Nagrath and M Gopal: Control Systems Engineering, 3rd Ed, New Age
Publication.
2. Richard C Dorf, Robert H Bishop : Modern Control Systems, Prentice-Hall
3. M. GOPAL:Digital Control and State Variable Methods , TMH
4. B.C.Kuo, “Digital Control System”,Saunders College Publishing.

5. C.H. Houpis and G.B.Lamont, “Digital Control Systems:MGH
6. Donald E. Kiv, “Optimal Control Theory: An Introduction” Prentice Hall
7. D.Roy Choudhary, “Modern Control Engineering”, Prentice Hall of India
8. C T Chen, System Theory & Design, Oxford University Press
6EE2 HIGH VOLTAGE ENGINEERING
Unit-1 (i) Breakdown in Gases: Introduction to mechanism of breakdown in
gases, Townsend’s
breakdown mechanism. Breakdown in electromagnetic gases, Application of
gases in power
system.
(ii) Breakdown in Liquids: Introduction to mechanism of breakdown in liquids,
suspended
solid particle mechanism and cavity breakdown. Application of oil in power
apparatus.
(iii) Breakdown in solids: Introduction to mechanism of breakdown in solids,
electromechanical breakdown, treeing & tracking breakdown and thermal
breakdown.
Unit-2 (i) High DC Voltage Generation: Generation of high dc voltage, basic
voltage multiplier
circuit.
(ii) High AC Voltage Generation: Cascaded Transformers.
(iii) Impulse Voltage generation: Impulse voltage, basic impulse circuit,
Mark’s multistage
impulse generator.
(iv) Measurement of High Voltage: Potential dividers - resistive, capacitive
and mixed

potential dividers. Sphere gap- Construction and operation. Klydonorgraph.
Unit-3 Nondestructive Insulation Tests: (i) Measurement of resistively,
dielectric constant and loss
factor. High Voltage Schering Bridge- measurement of capacitance and
dielectric loss.
(ii) Partial Discharges: Introduction to partial discharge, partial discharge
equivalent circuit.
Basic wide-band and narrow band PD detection circuits.
Unit-4 (i) Over voltages: Causes of over voltages, introduction to lightning
phenomena, over voltages
due to lighting.
(ii) Travelling Waves: Travelling waves on transmission lines-open end line,
short circuited
line, line terminated through a resistance, line connected to a cable,
reflection and refraction at a
T-junction and line terminated through a capacitance. Attenuation of
traveling waves.
Unit-5 (i) Over Voltage Protection: Basic construction and operation of
ground wires- protection
angle and protective zone, ground rods, counterpoise, surge absorber, rod
gap and arcing horn,
lighting arresters - expulsion type, non -linear gap type and metal oxide
gapless type.
(ii) Insulation Coordination: Volt - time curves, basic impulse insulation
levels, coordination
of insulation levels.

1. Naidu:High Voltage Engineering 4/e, TMH
2. Kauffel-High Voltage engineering, ELSEVIER
3. Wadhwa: High Voltage Engg., Wiley Eastern Ltd
4. Kuffe E. & Abdulla M., High Voltage Engineering, Pergman Press
5. Alston L.L., H. V. Technology, Oxford, University Press
6. Thapar B., Power System Transients and High Voltage Principles , Capital
Pub.
7. Subir Ray,’ An Introduction to High Voltage Engineering’ Prentice Hall of
India
6EE3 PROTECTION OF POWER SYSTEM Unit-1 (i) Causes and consequences
of dangerous currents: Faults, overloads and switching over
currents. Introduction to protection, trip circuit of a circuit breaker.
Functional characteristics of
a relay, zone of protection, primary and backup protection.
(ii) CTs & PTs: Current transformer construction, measurement and
protective CTs. Type of
potential transformers. Steady state ratio and phase angle errors in CTs and
PTs. Transient errors
in CT and CVT (Capacitive Voltage Transformer).
Unit-2 Overcurrent Protection: HRC fuse and thermal relay. Overcurrent (OC)
relays –
instantaneous, definite time, inverse time and inverse definite minimum time
overcurrent relays,
time and current gradings. Induction disc type relay. Directional overcurrent
relay, 30
◦

, 60
◦
and
90
◦
connections. Earth fault relay. Brief description of overcurrent protective
schemes for a
feeder, parallel feeders and ring mains.
Unit-3 Generator Protection: Stator protection – differential and percentage
differential protection,
protection against stator inter-turn faults, stator overheating protection.
Rotor protectionprotection against excitation and prime mover failure, field
earth fault and unbalanced stator
currents (negative sequence current protection).
Unit-4 (i) Transformer Protection: Percentage differential protection,
magnetizing inrush current,
percentage differential relay with harmonic restraint. Buchholz relay.
Differential protection of
generator transfer unit.
(ii) Busbar Protection: Differential protection of busbars. High impedance
relay scheme, frame
leakage protection.
Unit-5 (i) Transmission Line Protection: Introduction to distance protection.
Construction, operating
principle and characteristics of an electromagnetic impedance relay. Effect
of arc resistance.

Induction cup type reactance and mho relays. Comparison between
impedance, reactance and
mho relays. Three stepped distance protection of transmission line.
(ii) Induction Motor Protection: Introduction to various faults and abnormal
operating
conditions, unbalance supply voltage and single phasing. Introduction to
protection of induction
motors- HRC fuse and overcurrent, percentage differential, earth fault and
negative sequence
voltage relays.
1. BADRI RAM:Power System Protection and Switchgear , TMH
2. Ravindra Nath M. Chander, Power System Protection and Switch Gear,
John Wiley Eastern
3. Sunil S. Rao. Power System Protection and Switch Gear, Khanna
Publishers 1989
4. Oza:Power System Protection and Switchgear , TMH
5. T.S. Madhava Rao, Power System Protections (Static Relays), Tata
McGrwaw-hill, 1989.
6. A.R. van C Warrington, Protective Relays, Chapman and Hall London, 1968.
7. S.K. Basu and S. Chaudhary, Power System Protection, Raju Primlan
Oxford, 1983.
6EE4 ADVANCED POWER ELECTRONICS
Unit-1 AC Voltage Controllers: Principle of On-Off Control, Principle of Phase
control, Single Phase
Bi-directional Controllers with Resistive Loads, Single Phase Controllers with
Inductive Loads,

Three Phase full wave AC controllers, AC Voltage Controller with PWM
Control.
Unit-2 Inverters: Principle of Operation, Single-phase bridge inverters, Three
phase bridge Inverters:
180 and 120 degree of conduction. Voltage control of Single Phase and Three
Phase Inverters,
Current Source Inverters, Harmonics and its reduction techniques.
Unit-3 Cycloconverters: Basic principle of operation, single phase to single
phase, three-phase to
three-phase and three-phase to single phase cycloconverters. Output
equation, Control circuit.
Unit-4 DC Power Supplies: Switched Mode DC Power Supplies, flyback
converter, forward
converter, half and full bridge converter, resonant DC power supplies, bi-directional
power
supplies.
Unit-5 AC Power Supplies: Switched mode power supplies, Resonant AC
power supplies, bidirectional AC power supplies. Multistage conversions,
Control Circuits: Voltage Mode
Control, Current Mode ControlReference/Suggested Books
1. M.H. Rashid,“Power Electronics: Circuits, Devices & Applications”,
Prentice Hall of India
Ltd. 3
rd
Edition,2004.
2. Bose -Power Electronics & Motor Drives ELSEVIER

3. V.R. Moorthy, “Power Electronics: Devices, Circuits and Industrial
Applications” Oxford
Press, 2007.
4. V Subrahmanyam: Power Electronics, New Age Inc. Publishers, New Delhi.
5. Chakrabarti & Rai, “Fundamentals of Power Electronics & Drives”Dhanpat
Rai & Sons.
6. Ned Mohan, T.M.Undeland and W.P.Robbins, “Power
Electronics:Converters, Applications
and Design”, Wiley India Ltd,2008.
7. R Krishnan, electric motor drives: modeling, analysis and control, Pearson
Edu
8. Randal Shaffer, “Fundamentals of Power Electronics with MATLAB”
Firewall Media, 2007.
6EE5 DATA STRUCTURES IN C
Unit-1 Performance Measurement: Space complexity and Time complexity,
big oh, omega and theta
notations and their significance. Linear Lists - Array and linked
representation, singly & doubly
linked lists. Concept of circular linked lists.
Unit-2 Array & Matrices: Row and Column Major mapping & representation,
irregular 2D array,
Matrix operations, Special matrices: diagonal, tri-diagonal, triangular and
symmetric. Sparse
matrices representation and its transpose.
Unit-3 Stacks: Representation in array & linked lists, basic operation,
Applications of stacks in

parenthesis matching, towers of Hanoi etc. Queues - Representation in array
& linked lists,
applications, circular queues.
Unit-4 Trees: Binary Tree, representation in array & linked lists, basic
operation on binary trees,
binary tree traversal (preorder, post order, in order). Search Trees - Binary
search tree, indexedbinary search tree, basic operation, AVL tree, B-tree &
Heap Tree.
Unit-5 Graphs: Representation of unweighted graphs, BFS, DFS, and Minimum
cost spanning trees,
Single source shortest path. Sorting - Bubble sort, insertion sort, merge sort,
selection sort, quick
sort, heap sort.
1. Havowitz & Sawn: Data structures in Pascal (BPB Publication)
2. Havowitz & Sawhni: Data structures in C & C++ (BPB Publication)
3. Tannenbaum: Data structures in C (PHI)
4. PAI:Data Structures and Algorithms , TMH
5. TREMBLAY: Introduction to Data Structures with Applications , TMH
6EE6.1 ADVANCED MICROPROCESSORS
Unit-1 8086 Microprocessor: Hardware specifications, architecture, address
spaces, clock generator,
bus controller and arbiter, Minimum and maximum mode, System Bus Timing.
Unit-2 Software & Instruction Set: Assembly language programming:
addressing mode and

instructions of 8086, linking and execution of programs, MACRO
programming, assembler
directives and operators.
Unit-3 I/O Interfaces: Programmable peripheral interfacing (8255, 8155),
Programmable Timer
interfacing (8253, 8254), Programmable interrupt controller (8259) Serial
Communication
interfaces.
Unit-4 Data & Memory Interfacing: A/D, D/A converter interfacing, Memory
interfacing and
Decoding, DMA controller.
Unit-5 Multiprocessor Configurations: 8086 based Multiprocessor systems.
8087 Numeric data
processor.
1. John Freer - System design with Advance Microprocessors, A.H. Wheeler
2. Ray & Bhurchandi: Advanced Microprocessors and Peripherals 2/e (TMH)
3. Gibson - 16-Bit Microprocessor.
4. Brey – 16-Bit Microprocessor
5. Ray, A.K. & Burchandi, K.m., “Advanced Microprocessors and Peripherals:
Architeacture,
Programming and Interfacing” Tata Mc.Graw Hill.
6. Renu Sing & B.P.Singh, “Advanced Microprocessors and Microcontrollers”
New Age
Krishna Kant,”Microprocessors and Microcontrollers” PHI Learning.
7. Brey, Barry B. “The INTEL Microprocessors” Pearson Education.

8. Ayala, “The 8051 Micro Controller”, Centage Learning.
9. Mazidi M.A., Maizidi J.G. Mckinlay R.D., “The 8051 Microcontroller and
Embedded
Systems” Pearson Education.
6EE6.2 POWER SYSTEM INSTRUMENTATION
Unit-1 Theory of Errors: Accuracy and precision, systematic and random
errors, limits of error,
probable error and standard deviation. Gaussian error curves, combination of
errors.
Unit-2 Transducers: Construction & Operating Characteristics of active and
digital transducers,
Measurement of temperature, pressure, displacement, acceleration, noise
level, Instrumentation
for strain, displacement, velocity, acceleration, force, torque and
temperature.
Unit-3 Signal Conditioning: Instrumentation amplifiers, isolation amplifiers,
analog multipliers,
analog dividers, function generators, timers, sample and hold, optical and
magnetic isolators,
frequency to voltage converters, temperature to current converters.
Shielding and grounding.
Unit-4 Power System Instrumentation-I: Measurement of voltage, current,
phase angle, frequency,
active power and reactive power in power plants. Energy meters and
multipart tariff meters.
Unit-5 Power System Instrumentation-II: Capacitive voltage transformers
and their transient

behavior, Current Transformers for measurement and protection, composite
errors and transient
response.
1. R H Cerni and L E Foster: Instrumentation for Engineering Measurements,
John Wiley and
Sons,
2. Curtis and D Hohnson: Process Control Instrumentation Technology, John
Wiley and sons.
3. R Morrison: Instrumentation Fundamentals and Applications, John Wiley
and Sons
4. A.K.Sawhney, “Advanced Measurements & Instrumentation”, Dhanpat Rai
& Sons
5. E.O. Decblin, “Measurement System – Application & design”, Mc Graw Hill.
6. W.D. Cooper and A.P. Beltried, “Electronics Instrumentation and
Measurement Techniques”
Prentice Hall International
7. A.S. Moris / Principles of Measurement & Instrumentation / Prentice Hall,
1993.
6EE6.3 DIGITAL COMMUNICATION AND INFORMATION THEORY
Unit-1 PCM & DELTA Modulation Systems: PCM and delta modulation,
quantization noise in PCM
and delta modulation. Signal-to-noise ratio in PCM and delta modulation, T1
Carrier System,
Comparison of PCM and DM. Adaptive delta Modulation. Bit, word and frame
synchronization,
Matched filter detection.

Unit-2 Digital Modulation Techniques: Various techniques of phase shift,
amplitude shift and
frequency shift keying. Minimum shift keying. Modulation & Demodulation.
Unit-3 Error Probability in Digital Modulation: Calculation of error
probabilities for PSK, ASK,
FSK & MSK techniques.
Unit-4 Information Theory: Amount of Information, Average Information,
Entropy, Information rate,
Increase in Average information per bit by coding, Shannon's Theorem and
Shannon's bound,
Capacity of a Gaussian Channel, BW-S/N trade off, Orthogonal signal
transmission.
Unit-5 Coding: Coding of Information, Hamming code, Single Parity-Bit Code,
Linear Block code,
cyclic code & convolutional code.
1. H. Taub & D.L. Schilling-"Principles of Communication Systems", Tata Mc-
Graw Hill.2. Simon Haykin-"Communication Systems", John Wiley & Sons.
3. Proakis –“Digital Communication”, Mc-Graw Hill.
4. Sklar – “Digital Communication”, Pearson Education.
5. P. Chakrabarti – “Principles of Digital Communications”, Danpatrai & Sons.
6. K. Sam Shanmugam – “Digital and Analog Communication System”, John
Wiley Sons.
7. Lathi, B.P. / “Modern Digital &Analog Communication System” /Oxford
Press.
8. A.B. Carlson / “Digital Communication Systems”, Tata McGraw-Hill.

6EE7 CONTROL SYSTEM LAB
1 Introduction to MATLAB Computing Control Software.
2 Defining Systems in TF, ZPK form.
3 (a) Plot step response of a given TF and system in state-space. Take
different values of damping
ratio and wn natural undamped frequency. (b) Plot ramp response.
4 For a given 2
nd
order system plot step response and obtain time response specification.
5 To design 1st order R-C circuits and observe its response with the
following inputs and trace the
curve. (a) Step (b) Ramp (c) Impulse
6 To design 2nd order electrical network and study its transient response for
step input and
following cases. (a) Under damped system (b) Over damped System. (c)
Critically damped
system.
7 To Study the frequency response of following compensating Networks, plot
the graph and final
out corner frequencies. (a) Log Network (b) Lead Network (c) Log-lead
Network.
8 To draw characteristics of ac servomotor
9 To perform experiment on Potentiometer error detector.
10 Check for the stability of a given closed loop system.
11 Plot bode plot for a 2

nd
order system and find GM and PM.
6EE8 POWER SYSTEM LAB
1 Study the burden effect on the performance of CT and measure ratio error.
2 Find out the sequence components of currents in three 1-Phase
transformers and 3-Phase
transformer and compare their results.
3 (i) Study over current relay.
(ii) Draw the current-time characteristic of an over current relay for TMS=1 &
0.5 and
PSM=1.25 & 1.0.
4 (i) Study percentage bias differential relay.
(ii) Plot the characteristics of a percentage bias differential relay for 20%,
30% and 40% biasing.
5 Study gas actuated Buchholz relay.
6 Study under frequency relay and check it’s setting experimentally.
7 Design a HV transmission line.
8 Study a typical grid substation.
9 Study earthing of power station, substation and building
6EE9 DATA STRUCTURES LAB
1 Simple array and sorting algorithm implementations.
2 Addition, multiplication and transpose of sparse matrices represented in
array form.
3 Polynomial addition, multiplication (8
th

degree polynomials), using array & linked lists.
4 Implementation of stack and queue using array & linked lists.
5 Implementation of circular queue using array.6 Infix to postfix/prefix
conversion.
7 Binary search tree creation and traversing.
8 Generation of spanning trees for a given graph using BFS & DFS algorithms.
9 AVL tree implementation (creation, insertion, deletion).
10 Symbol table organization (Hash Table).
11 Simple array and sorting algorithm implementations.
12 Basic operation over linked list (add node, delete node).
6EE10 ADVANCED POWER ELECTRONICS LAB
1 Study and test AC voltage regulators using triac, antiparallel thyristors and
triac & diac.
2 Study and test single phase PWM inverter.
3 Study and test buck, boost and buck- boost regulators.
4 Study and test MOSFET chopper.
5 Study and test Zero voltage switching.
6 Study and test SCR DC circuit breaker.
7 Control speed of a dc motor using a chopper and plot armature voltage
versus speed
characteristic.
8 Control speed of a single-phase induction motor using single phase AC
voltage regulator.
9 (i) Study single-phase dual converter. (ii) Study speed control of dc motor
using single-phase

dual converter.
10 Study one, two and four quadrant choppers (DC-DC converters).
11 Study speed control of dc motor using one, two and four quadrant
choppers.
12 Study single-phase cycloconverter.
B. TECH. VII- SEMESTER
7EE1 DATA BASE MANGEMENT SYSTEM
Unit-1 Introduction, need, purpose and goals of DBMS. DBMS Architecture,
Concept of keys,
Generalization and specialization, introduction to relational data model, ER
modeling, concept
of ER diagram.
Unit-2 Database Design: Conceptual Data Base design. Theory of
normalization, Primitive and
composite data types, concept of physical and logical databases, data
abstraction and data
independence, relational algebra and relational calculus.
Unit-3 SQL, DDL and DML. Constraints assertions, views database security.
Application Development
using SQL: Host Language interface, embedded SQL programming. GL’s,
Forms management
and report writers. Stored procedures and triggers. Dynamic SQL, JDBC.
Unit-4 Internal of RDBMS: Physical data organization in sequential, indexed,
random and hashed
files. Inverted and multilist structures.

Unit-5 (i) Transaction Management: Transaction concept, transaction state,
serializability, conflict
serializabiltiy, view serializability. (ii) Concurrency Control: Lock based
protocol. (iii)
Deadlock Handling: Prevention detection, recovery. (iv) Recovery System:
Log based
recovery.
1. Silverschatz Korth and Sudarshan – D00atabase System Concepts, 5th ed.,
Tata Mc-Graw Hill.
2. Raghu Rama Krishnan – Database Management Systems, 2nd ed., Tata Mc-
Graw Hill.
3. Elmasari – Fundamentals of Data Base Systems, Pearson Education.
4. Gordon C. Everest – Database Management Objectives, System Functions
and Administration, TMH.
5. Date C.J., “An Introduction To Database System”,Addition Wesley
6. Alex Berson & Stephen J.Smith,“Data Warehousing,Data Mining &
OLAP”,TMH.
7. Mallach, “Data Warehousing System”, Mc. Graw Hill
8. Majumdar & Bhattacharya, “Database Management System”, Tata Mc
Graw Hill
7EE2 POWER SYSTEM ANALYSIS
Unit-1 (i) Percent and per unit quantities. Single line diagram for a balanced
3-phase system. (ii)
Admittance Model: Branch and node admittances Equivalent admittance
network and
calculation of Y bus.

Modification of an existing Y bus.
Unit-2 (i) Impendence Model: Bus admittance and impedance matrices.
Thevenin’s theorem and Z bus.
Direct determination of Z bus. Modification of an existing bus. (ii)
Symmetrical fault Analysis:
Transient on a Transmission line, short circuit of a synchronous machine on
no load, short circuit
of a loaded synchronous machine. Equivalent circuits of synchronous
machine under sub transient,
transient and steady state conditions. Selection of circuit breakers,
Algorithm for short circuit
studies. Analysis of three-phase faults.
Unit-3 (i) Symmetrical Components: Fortescure theorem, symmetrical
component transformation.
Phase shift in star-delta transformers. Sequence Impedances of transmission
lines, Synchronous
Machine and Transformers, zero sequence network of transformers and
transmission lines.
Construction of sequence networks of power system. (ii) Fault Analysis:
Analysis of
single line to ground faults using symmetrical components, connection of
sequence networks
under the fault condition.
Unit-4 Unsymmetrical Fault Analysis: (i) Analysis of line-to-line and double
line to ground faults
using symmetrical components, connection of sequence networks under
fault conditions.

(ii) Analysis of unsymmetrical shunt faults using bus impedance matrix
method.
Unit-5 Load Flow Analysis: Load flow problem, development of load flow
equations, bus
classification. Gauss Seidel, Newton Raphosn, decoupled and fast decoupled
methods for load
flow analysis. Comparison of load flow methods.
1. J. J. Grainger, William, D. Stevenson Jr. – Power System Analysis.
McGraw-Hill
2. Nagrath and Kothari – Power System Engineering 2/e Tata Mc Graw Hill
3. Haadi SAADAT- Power System Analysis (With Disk) ,TMH
4. T.K Nagsarkar & M.S. Sukhija, “Power System Analysis” Oxford University
Press,2007.
5. W.D. Stevenson, Jr. “Elements of Power System Analysis”, Mc Graw Hill.
6. J.D. Glover, M.S. Sharma & T.J.Overbye, “Power System Analysis and
Design” Thomson,
2008.
7. Kothari & Nagrath, “Modern Power System Analysis” Tata Mc. Graw Hill.
7EE3 ARTIFICIAL INTELLIGENCE TECHNIQUES
Unit-1 Artificial Intelligence: Introduction to AI and knowledge based Expert
systems: Introduction,
Importance and Definition of AI, ES, ES building tools and shells.
Unit-2 Knowledge Representation: Concept of knowledge, Representation of
knowledge using logics

rules, frames. Procedural versus. Declarative knowledge, forward versus
backward chaining.
Control Strategies: -Concept of heuristic search, search techniques depth
first search, Breath
first search, Generate & test hill climbing, best first search.
Unit-3 Artificial Neural Network: Biological Neurons and synapses,
characteristics Artificial Neural
Networks, types of activation functions. Perceptions: Perception
representation, limitations of
perceptrons. Single layer and multiplayer perceptrons. Perceptron learning
algorithms.
Unit-4 Basic Concepts in Learning ANN: Supervised learning, Back
propagation algorithm,
unsupervised learning, Kohonen’s top field network & Algorithm.
Unit-5 Fuzzy Logic: Fuzzy logic concepts, Fuzzy relation and membership
functions, Defuzzufication,
Fuzzy controllers Genetic algorithm: concepts, coding, reproduction,
crossover, mutation, scaling and fitness.
1. Elaine Rich and Kevin Knight, Artificial Intelligence 3/e, TMH
2. PADHY: ARTIFICIAL INTELLIGENCE & INTELLIGENT SYSTEMS, Oxford
3. James A Anderson, An introduction to Neural Networks.
4. Dan. W Patterson, Artificial Intelligence and Expert Systems.
5. Kumar Satish, “Neural Networks” Tata Mc Graw Hill
6. S. Rajsekaran & G.A. Vijayalakshmi Pai, “Neural Networks,Fuzzy Logic and
Genetic

Algorithm:Synthesis and Applications” Prentice Hall of India.
7. Siman Haykin,”Neural Netowrks”Prentice Hall of India
7EE4 UTILIZATION OF ELECTRICAL POWER
Unit-1 (i)Electric Heating: Different methods of electric heating. Principle of
high frequency
induction and di-electric heating. Construction, operation, performance and
applications of arc
furnace and induction furnace. (ii) Electric Welding: Welding process,
welding transformer,
Classification of Electric Welding: arc welding, resistance welding, welding
of various metals.
Unit-2 Illuminations: Definitions, laws of illuminations, polar curves, luminous
efficiency,
photometer, incandescent lamps: filament materials, halogen lamp. electric
discharge lamps:
sodium vapour lamp mercury vapour lamp and fluorescent lamp. Light
Calculations:
commercial, industrial, street and flood lighting.
Unit-3 Electrolytic Process: Principles and applications of electrolysis,
electro-deposition,
manufactures of chemicals, anodizing, electro polishing electro-cleaning,
electroextraction,
electrorefinig, electro-stripping (parting) power supplies for electrolytic
process.
Unit-4 Electric Traction & Means of Supplying Power: Systems of Electric
Traction: DC & AC
Systems, Power Supply for Electric Traction System: Comparison and
application of different

systems. Sub-station equipment and layout, conductor rail & pantograph.
Unit-5 Traction Methods: Types of services, speed time and speed distance
curves, estimation of
power and energy requirements, Mechanics of train movement. Co-efficient
of adhesion,
Adhesive weight, effective weight. Traction Motor Controls: DC and AC
traction motors,
Series parallel starting. Methods of electric braking of traction motors.
1. H. Partab,“Art and Science of Electrical Energy” Dhanpat Rai & Sons
2. H. Partab, “Modern Electric Traction” Dhanpat Rai & Sons.
3. C.L. Wadhwa – Utilization of Electric Traction Electric Power.
4. G.K.Dubey,“Fundamentals of Electric Drives” Narosa Publishing House
5. Vedam and Subrahmanyam – Concept & Application of Electric Drives
(TMH)
7EE5 POWER SYSTEM ENGINEERING
Unit-1 Economic Operation of Power Systems: Introduction, system
constraints, optimal operation
of power systems. Input output, heat rate and incremental rate curves of
thermal generating
units. Economic distribution of load between generating units within a plant.
Economic
distribution of load between power stations, transmission loss equation.
Introduction to unit
commitment and dynamic programming.

Unit-2 Power System Stability -I: Power angle equations and power angle
curves under steady state
and transient conditions. Rotor dynamics and swing equation (solution of
swing equation not
included), synchronizing power coefficient. Introduction to steady state and
dynamic stabilities,
steady state stability limit.
Unit-3 Power System Stability-II: Introduction to transient stability. Equal
area criterion and its
application to transient stability studies under basic disturbances, critical
clearing angle and
critical clearing time. Factors affecting stability and methods to improve
stability.
Unit-4 (i) Excitation Systems: Introduction of excitation systems of
synchronous machines, types of
excitation systems, Elements of various excitation systems and their control
(functional block diagrams and their brief description)-DC excitation
systems, AC excitation systems, brushless
excitation system. (ii) Interconnected Power Systems: Introduction to
isolated and
interconnected powers systems. Reserve capacity of power stations,
spinning and maintenance
resaves. Advantages and problems of interconnected power systems. Power
systems inter
connection in India.
Unit-5 (i) Tap Changing transformer, phase angle control and phase shifting
transformer. Series

compensation of transmission lines, location and protection of series
capacitors, advantages and
problems. (ii) Introduction to power system security. (iii) Introduction to
voltage stability.
1. J. Nagrath and D.P. Kothari: Power System Engineering 2/e (TMH)
2. J. J. Grainger and W. D. Stevenson: Power System Analysis (TMH)
3. B. R. Gupta, “Power System Analysis and Design” Third Edition, S. Chand &
Co.
4. C. L. Wadhwa, “Electrical Power Systems” New age international Ltd. Third
Edition
5. W. D. Stevenson, “Element of Power System Analysis”, McGraw Hill.
6. B.R. Gupta,“Generation of Electrical Energy”, S. Chand Publication.
7EE6.1 ELECTROMAGNETIC FIELD THEORY
Unit-1 Introduction: Vector Relation in rectangular, cylindrical, spherical and
general curvilinear
coordinate system. Concept and physical interpretation of gradient,
Divergence and curl,
Green’s Stoke’s and Helmholz theorems.
Unit-2 Electrostatics: Electric field vectors-electric field intensity, flux
density & polarization. Electric
field due to various charge configurations. The potential functions and
displacement vector.
Gauss’s law. Poisson’s and Laplace’s equation and their solution. Uniqueness
theorem.
Continuity equation. Capacitance and electrostatics energy. Field
determination by method of

images. Boundary conditions. Field mappings and concept of field cells.
Unit-3 Magnetostatics: Magnetic field vector: Magnetic field intensity, flux
density & magnetization,
Bio-Savart’s law, Ampere’s law, Magnetic scalar and vector potential, self &
mutual
inductance, Energy stored in magnetic field, Boundary conditions, Analogy
between electric and
magnetic field, Field mapping and concept of field cells.
Unit-4 Time Varying Fields: Faraday’s law, Displacement currents and
equation of continuity.
Maxwell’s equations, Uniform plane wave in free space, dielectrics and
conductors, skin effect
sinusoidal time variations, reflections, refraction & polarization of UPW,
standing wave ratio.
Pointing vector and power considerations.
Unit-5 Transmission Lines: The high-frequency circuit. LCR ladder model. The
transmission line
equation. Solution for loss-less lines. Wave velocity and wave impedance.
Reflection and
Transmission coefficients at junctions. VSWR.
1. HAYT-Engineering Electromagnetics 7/e, (With CD), TMH
2. SADIKU:PRINCIPLES OF ELECTROMAGNETICS 4E (Intl. Version) Oxford
3. David K Cheng – Field and Wave Electromagnetic. 2nd Ed., Wesley
Publishing Company.
4. Griffith – Introduction to Electrodynamics. 2nd Ed., Prentice Hall of India.

5. J D Kraus, Electromagnetic. 5th edition, (TMH).
6. V.V. Sarwate – Electromagnetic Field and Waves, Willey Eastern Ltd.
7. Bhag Guru, Electromagnetic Field Theory Fundamentals, Cambridge Uni.
Press.
8. Kraus, F. “Electromagnetic” Tata Mc. Graw Hill 5th Edition
7EE6.2 COMPUTER AIDED DESIGN OF ELECTRICAL MACHINES Unit-1 Basic
Principles of Electrical Machine Design: Specifications, Factors affecting the
design,
Limitations, main dimension, loadings, output equation, factor affecting the
size and rating,
Electrical Engineering Materials: conducting, magnetic and insulating
materials. Magnetic
Circuit Calculation: Ohm’s law for magnetic circuit, mmf required for air gap
and iron parts,
tapered teeth, real and apparent flux density, magnetizing current.
Unit-2 Heating and Cooling of Electrical Machines: heat dissipation and heat
flow equations,
Newton’s law of cooling, equations for temperature rise, Rating of Machines:
Continuous,
short and intermittent ratings, mean temperature rise, hydrogen cooling of
turbo alternators,
quantity of cooling medium.
Unit-3 Computer Aided Design of Transformers: Power and Distribution
Transformers, core and
yoke cross sections, square and stepped core, output equations, main
dimensions, types &,
design of windings, optimization concepts.

Unit-4 Computer Aided Design of Synchronous Machines: Turbo and Hydro
alternators, choice of
specific magnetic & electric loading, short circuit ratio and its effects, air
gap length, output
equation, main dimensions, flow charts for design of synchronous machine,
design of stator core
& winding.
Unit-5 Computer Aided Design of Induction Machines: Output equation, main
dimensions, design
criteria, flow charts for design of induction motor, air gap length, design of
stator core and
winding, rotor design.
1. A. K. Sawhney, “A Course in Electrical Machine Design” Dhanpat Rai &
Sons.
2. Generalized theory of electrical Machines by B. Edikins.
3. Electrical Machinery by Fitzegerald; Kingsley.
4. M.G. Say, “The Performance and Design of AC Machines” Pitman & Sons.
5. R.K. Agrawal – Electrical Machine Design
7EE6.3 ECONOMIC OPERATION OF POWER SYSTEMS
Unit-1 Economics of Power Generation: Introduction, cost of electrical
energy, expression for cost of
electrical energy, depreciation, power plant cost analysis, economics in
plant selection, selection
of types of generation and types of equipments, factors effecting economic
generations and

distributions, generating cost, economics of different types of generating
plants.
Unit-2 Economical Operations of thermal power plants: Methods of loading
turbo generators, input,
output and heat rate characteristics, incremental cost, two generations
units, large no of units,
sequence of adding units, effects of transmission losses, economic
scheduling considering
transmission losses, coordination equations, penalty factors
Unit-3 Hydro Thermal coordination: Advantages of combined operation,
base load peak load
operation requirement, combined working of run-off river and steam plant,
reservoirs hydroplants and thermal plants (long term operational aspects),
short term hydro thermal coordination,
coordination equations, scheduling methods and applications.
Unit-4 Parallel Operations of Generators: Conditions, synchronizing current
and power, two
alternators in parallel (effect of change in excitation, load sharing, sharing of
load currents),
Infinite bus bars, active and reactive power control, synchronizing power,
torque, operating
limits of alternators, operating characteristics of cylindrical alternator rotor.
Unit-5 Economics for Electrical Engineers: Concepts of physical and
financial efficiencies of
electrical goods and services, supply and demand, break even and minimum
cost analysis, linear
and nonlinear break even, min cist analysis

1. Nagrath and Kothari: Modern Power System Analysis (TMH)
2. D.P. Kothari & I.J. Nagrath, “Modern Power System Analysis” Tata Mc
Graw Hill,
3. J. Wood & B.F. Wollenburg, “ Power Generation, Operation and Control “
John Wiley
4. O.I. Elgerd, “Electric Energy System Theory” Tata McGraw Hill.
5. P. Kundur, “Power System Stability and Control Mc Graw Hill.6. Arthur R.
Bergen and Vijay Vittal, Power System Analysis, Second Edition. PHI, 1999
7. C.L. Wadhwa, ‘Electrical Power Systems’, Newage International (P) Ltd.,
2000
8. C. Gross, Power Systems Analysis, 2nd Edition. John Wiley & Sons, 1986.
7EE7 DBMS LAB
1 Designing database and constraints using DDL statements.
2 Experiments for practicing SQL query execution on designed database.
3 Database connectivity using JDBC/ODBC.
4 Features of embedded SQL.
5 Designing front end in HLL and accessing data from backend database.
6 Designing simple projects using front end-back end programming.
7 Project for generating Electricity Bills
8 Project for managing student’s attendance/marks details.
7EE8 POWER SYSTEM MODELLING & SIMULATION LAB
1 Simulate Swing Equation in Simulink (MATLAB)
2 Modelling of Synchronous Machine.
3 Modelling of Induction Machine.
4 Simulate simple circuits using Circuit Maker.

5 (a) Modelling of Synchronous Machine with PSS (b) Simulation of
Synchronous Machine with
FACTS device.
6 (a) Modelling of Synchronous Machine with FACTS device (b) Simulation of
Synchronous
Machine with FACTS devices.
7 FACTS Controller designs with FACT devices for SMIB system.
7EE9 INDUSTRIAL ECONOMICS & MANAGEMENT
1 Money Banking and Trade: Functions of money, supply & demand for
money, money price
level & inflation, black money, meaning, magnitude & consequences.
Functions of Commercial
banks, banking system in India, shortcomings and improvements.. Function
of RBI, monetary
policy-making, objectives and features. Sources of public revenue, principles
of taxation, direct
and indirect taxes, Theory of international trade, balance of trade and
payment, Foreign
exchange control, devaluation New economic policy: Liberalization,
extending privatization,
globalization.
2 Management Principles: Management functions, responsibilities of
management to society,
development of management thought. Nature of planning, decision making,
management by
objectives, Line and staff authority relationships, decentralization and
delegation of authority,

span of management.
3 Production Management: Production planning and control, inventory
control, quality control
and Total quality management. Tools of project management - CPM, PERT,
project information
systems. Marketing functions, management of sales and advertising
marketing research.
4 Human Resource Management: Function, application of industrial
psychology for selection,
training and recruitment. Communication process, media channels and
barriers to effective
communication, theories of motivation, leadership.
5 Finance and Account Management: Engineering Economics: Investment
decision, present
worth, annual worth and rate of return methods. Payback time. Need for good
cost accounting
system, cost control techniques of financial control, financial statements,
financial ratios, breakeven analysis, budgeting and budgetary control.
B. TECH. VIII- SEMESTER8EE1 EHV AC/DC TRANSMISSION
Unit-1 EHV AC Transmission: Need of EHV transmission lines, power handling
capacity and surge
impedance loading. Problems of EHV transmission, bundled conductors:
geometric mean radius
of bundle, properties of bundle conductors. Electrostatic fields of EHV lines
and their effects,
corona effects: Corona loss, audio and radio noise.
Unit-2 Load Frequency Control: Introduction to control of active and reactive
power flow, turbine

speed governing system. Speed governing characteristic of generating unit
and load sharing
between parallel operating generators. Method of Load Frequency Control:
Flat frequency,
flat tie line and tie line load bias control. Automatic generation control
(description of block
diagram only).
Unit-3 Voltage Control: No load receiving end voltage and reactive power
generation. Methods of
voltage control. Synchronous phase modifier, shunt capacitors and reactors,
saturable reactors,
Thynstorised static VAR compensators- TCR, FC-TCR and TSC- TCR.
Unit-4 FACTS: Introduction to FACTS controllers, types of FACTS controllers,
Brief description of
STATCOM, Thyristor controlled series capacitors and unified power flow
controller.
Unit-5 HVDC Transmission: Types of D.C. links, advantages and
disadvantages of HVDC
transmission. Basic scheme and equipment of converter station. Ground
return. Basic principles
of DC link control and basic converter control characteristics. Application of
HVDC
transmission.
1. K.R. Padiyar – HVDC Power Transmission Systems. NEW AGE PUB
2. HVDC Power Transmission System, K.R, Padiyar, Wiley Eastern Ltd., 1990
3. E.W. Kimbark, Direct Current Transmission Vol: 1 Wiley Interscience, 1971.

4. J. Arrillaga, H.V.D.C Transmission, Peter Peregrines, 1983.
5. J. Arrillaga HVDC et. al, Computer Modelling of Electrical Power System.
John Wiley 1993.
6. R.D. Begamudre, E.H.V. A.C. Transmission, Wiley Eastern Ltd., 2nd edition.
7. S. Rao, EHV-AC and H.V.D.C. Transmission Engineering Practice, Khanna
publishers, 1990.
8. R. D. Begamudre, “Extra High Voltage AC Transmission Engineering” Wiley
Eastern.
8EE2 ELECTRIC DRIVES AND THEIR CONTROL
Unit-1 Dynamics of Electric Drives: Fundamental torque equations, speed-torque
conventions and
multiquardant operation, equivalent values of drive parameters, nature and
classification of load
torques, steady state stability, load equalization, close loop configurations of
drives.
Unit-2 DC Drives: Speed torque curves, torque and power limitation in
armature voltage and field
control, Starting, Braking-Regenerative Braking, dynamic braking and
plugging. Speed
Control-Controlled Rectifier fed DC drives, Chopper Controlled DC drives.
Unit-3 Induction Motor Drives-I: Starting, Braking-Regenerative braking,
plugging and dynamic
braking. Speed Control-Stator voltage control, variable frequency control
from voltage source,
Voltage Source Inverter (VSI) Control.
Unit-4 Induction Motor Drives-II: Variable frequency control from current
source, Current Source

Inverter (CSI) Control, Cycloconverter Control, Static rotor resistance
control, Slip Power
Recovery- Stator Scherbius drive, Static Kramer drive.
Unit-5 Synchronous Motor Drive: Control of Synchronous Motor-Separately
Controlled and VSI fed
Self-Controlled Synchronous Motor Drives. Dynamic and Regenerative
Braking of
Synchronous Motor with VSI. Control of Synchronous Motor Using Current
Source Inverter
(CSI)
1. G K Dubey: Fundamentals of Electrical Drives, Narosa Publishing House,
New Delhi.
2. V Subrahmanyam: Thyristor Control of Electric Drives, Tata McGraw Hill,
New Delhi.
3. V Subrahmanyam: Electric Drives- Concepts and Applications, Tata
McGraw Hill.
4. S K Pillai: A First Course on Electrical Drives, Wiley Eastern limited,
India.5. G K Dubey: Power Semiconductor Controlled Drives, Prentice Hall,
Englewood Cliffs.
6. B K Bose: Power Electronics and A. C. Drives, Prentice Hall.
7. G.K. Dubey, “Fundamentals of Electric Drives”, Narosa publishing House.
8. M.Chilkin, “Electric Drives”,Mir Publishers, Moscow.
9. N.K. De and Prashant K.Sen, “Electric Drives”, Prentice Hall of India Ltd.
8EE3 SWITCHGEAR & PROTECTION
Unit-1 (i) Static Relays: Introduction to static relays, merits and demerits.
Comparators: amplitude

and phase comparators, duality between amplitude and phase comparators.
Introduction to (a)
amplitude comparators-circulating current type, phase splitting type and
sampling type, (b)
phase comparators-vector product type and coincidence type.
(ii) Static over Current Relays: Introduction to instantaneous, definite time,
inverse time and
directional overcurrent relays.
Unit-2 (i) Static Differential Relays: Brief description of static differential
relay schemes-single phase
and three phase schemes. Introduction to static differential protection of
generator and
transformer.
(ii) Static Distance Relays: Introduction to static impedance, reactance and
mho relays.
Unit-3 (i) Carrier Current Protection: Basic apparatus and scheme of power
line carrier system.
Principle of operation of directional comparison and phase comparison
carrier protection and
carrier assisted distance protection.
(ii) Distance Protection: Effect of power swings on the performance of
distance protection. Out
of step tripping and blocking relays, mho relay with blinders. Introduction to
quadrilateral and
elliptical relays.
Unit-4 Circuit Breakers I: Electric arc and its characteristics, arc
interruption-high resistance

interruption and current zero interruption. Arc interruption theories–recovery
rate theory and
energy balance theory. Restriking voltage and recovery voltage, develop
expressions for
restriking voltage and RRRV. Resistance switching, current chopping and
interruption of
capacitive current. Oil circuit breakers-bulk oil and minimum oil circuit
breakers. Air circuit
breakers.
Unit-5 (i) Circuit Breakers II: Air blast, SF6 and vacuum circuit breakers.
Selection of circuit
breakers, rating of circuit breakers.
(ii) Digital Protection: Introduction to digital protection. Brief description of
block diagram of
digital relay. Introduction to digital overcurrent, transformer differential and
transmission line
distance protection.
1. S. S. Rao, “Switchgear and Protection”, Khanna Publishers.
2. B. Ravindranath and M. Chander, Power system Protection and
Switchgear, Wiley.
3. B. Ram and D. N. Vishwakarma, “Power System Protection and
Switchgear”, TMH.
4. Y. G. Paithankar and S R Bhide, “Fundamentals of Power System
Protection”, PHI.
5. T.S.M Rao,“Power System Protection: Static Relays with Microprocessor
Applications”

Tata Macgraw Hill”.
6. A.R. Van C. Warringtaon, “Protective Relays- Their Theory and Practice,
Vol. I & II” Jhon
Willey & Sons.
8EE4.1 NON-CONVENTIONAL ENERGY SOURCES
Unit-1 (i) Introduction: World energy situation, conventional and non-conventional
energy sources,
Indian energy scene.
(ii) Tidal Energy: Introduction to tidal power. Components of tidal power
plants, double basin
arrangement. Power generation. Advantages and limitations of tidal power
generation. Prospects
of tidal energy in India.
Unit-2 Solar Energy: Solar radiation, solar radiation geometry, solar radiation
on tilted surface. Solar
energy collector. Flat- plate collector, concentrating collector – parabolidal
and heliostat. Solar pond. Basic solar power plant. Solar cell, solar cell array,
basic photo-voltaic power generating
system.
Unit-3 (i) Wind Energy: Basic principle of wind energy conversion, efficiency
of conversion, site
selection. Electric power generation-basic components, horizontal axis and
vertical axis wind
turbines, towers, generators, control and monitoring components. Basic
electric generation
schemes- constant speed constant frequency, variable speed constant
frequency and variable

speed variable frequency schemes. Applications of wind energy.
(ii) Geothermal Energy: Geothermal fields, estimates of geothermal power.
Basic geothermal
steam power plant, binary fluid geothermal power plant and geothermal
preheat hybrid power
plant. Advantages and disadvantages of geothermal energy. Applications of
geothermal energy.
Geothermal energy in India.
Unit-4 Nuclear Fusion Energy: Introduction, nuclear fission and nuclear
fusion. Requirements for
nuclear fusion. Plasma confinement - magnetic confinement and inertial
confinement. Basic
Tokamak reactor, laser fusion reactor. Advantages of nuclear fusion. Fusion
hybrid and cold
fusion.
Unit-5 Biomass Energy: Introduction, biomass categories, bio-fuels.
Introduction to biomass
conversion technologies. Biogas generation, basic biogas plants-fixed dome
type, floating
gasholder type, Deen Bandhu biogas plant, Pragati design biogas plant.
Utilization of bio gas.
Energy plantation. Pyrolysis scheme. Alternative liquid fuels –ethanol and
methanol. Ethanol
production.
1. Dr. A.N. Mathur – Non-Conventional Resources of Energy.
2. Boyle: Renewable Energy, 2E Oxford

3. S.P. Sukhatme – Solar Energy (TMH)
4. Duffie & Beckman – Solar Engineering of Thermal Processes.
5. BH KHAN: Non-Conventional Energy Resources, (TMH)
6. GARG & PRAKASH : Solar Energy : Fundamentals and Applications, TMH
7. Bio Energy by David Boyles, Elis Horwood Ltd.,
8. Renewable energy sources and conversion technology by N.K. Bansal, M.
Kleemann, M.
Heliss, Tata Mc-Graw-Hill, 1990.
8EE4.2 FACTS DEVICES & THEIR APPLICATIONS
Unit-1 Problems of AC transmission systems, power flow in parallel paths and
meshed system, factors
limiting loading capability, stability consideration. Power flow control of an
ac transmission
line. Basic types of facts controllers. Advantages of FACTS technology.
Unit-2 (i) Voltage-Sourced Converters: Basic concept of voltage-sourced
converters, single and three
phase bridge converters. Introduction to power factor control. Transformer
connections for 12-
pulse, 24 pulse and 48 pulse operations.
(ii) Static Shunt Compensators: Mid point and end point voltage regulation of
transmission
line, and stability improvement. Basic operating principle of Static
Synchronous Compensators
(STATCOM). Comparison between STATCOM and SVC.
Unit-3 Static Series Compensators: Concept of series capacitive
compensation, voltage and transient

stabilities, power oscillation and subsynehronous oscillation damping.
Introduction to thyristorswitched series capacitor (TSSC), thyristor
controlled series capacitor (TCSC), and static
synchronous series compensator, - operation, characteristics and
applications.
Unit-4 (i) Static Voltage and Phase Angle Regulators: Voltage and phase
angle regulation. Power
flow control and improvement of stability by phase angle regulator.
Introduction to thyristor
controlled voltage and phase angle regulators (TCVR and TCPAR)
(ii) Introduction to thyristor controlled braking resistor and thyristor
controlled voltage limiter.
Unit-5 (i) UPFC: Unified Power Flow Controller (UPFC), basic operating
principles, conventional
transmission control capabilities. Comparison of UPFC to series
compensators and phase angle
regulator. Applications of UPFC.(ii) IPFC: Interline Power Flow Controller
(IPFC), basic operating principles and
characteristics. Applications of IPFC.
1. K.R. Padiyar – Flexible AC Transmission Systems
2. N.G. Hingorani, L. Gyugyi: Understanding FACTS: IEEE Press Book.
3. Yong Hua Song, Allan T Johns : Flexible AC Transmission Systems FACTS
4. Xiao Ping Zhang, Christian Rehtanz, Bikash Pal: Flexible AC Transmission
Systems.
5. R Mohan & R M Mathur, Thyristor-based FACTS Controllers for Electrical
Transmission

Systems,, John Wiley
8EE4.3 POWER SYSTEM TRANSIENTS
Unit-1 Wave terminology, Development of wave quotations, Terminal
problems, Lattice diagrams,
Origin and Nature of power system transients and surges, Surge parameters
of plants,
Equivalent Circuit representations. Lumped and distributed circuit transients.
Unit-2 Line energisation and de-energisation transients-Earth and earthwire
effects. Current chopping
in circuit breakers. Short line fault condition and its relation to circuit
breaker duty. Trapped
charge effects. Effect of source and source representation in short line fault
studies.
Unit-3 Control of transients, Lightening phenomenon, influence of tower
footing resistance and earth
resistance, Traveling waves in distributed parameters multiconductor lines,
parameters as a
function of frequency.
Unit-4 Mechanism of Lightning Discharge Types of Lightning strokes, Harmful
effects of lighting,
protections against lightning, overhead Ground wires.
Unit-5 Lightening Arresters, Types of lightening arresters, Surge Absorber
simulation of surge
diverters in trarient analysis. Fourier integral and z transform methods in
power system trarient.
1. Power System Transients: C S Indulkar and D P Kothari., NEW AGE

2. Lou Van der Sluis: Transients in Power Systems, John Wiley
3. NR Watson, J Arrillaga: Power Systems Electromagnetic Transients, John
Wiley
8EE5 COMPUTER BASED POWER SYSTEM LAB
1 Fault analysis (for 3 to 6 bus) and verify the results using MATLAB or any
available software
for the cases: (i) LG Fault (ii) LLG Fault (iii) LL Fault and (iv) 3-Phase Fault
2 Load flow analysis for a given system (for 3 to 6 bus) using (i) Gauss Seidal
(ii) Newton
Raphson (iii) Fast Decoupled Method and verify results using MATLAB or any
available
software
3 Study of voltage security analysis
4 Study of overload security analysis and obtain results for the given problem
using MATLAB or
any software.
5 Study of economic load dispatch problem with different methods.
6 Study of transient stability analysis using MATLAB/ETAP Software.
8EE6 ELECTRICAL DRIVES AND CONTROL LAB
1 Study and test the firing circuit of three phase half controlled bridge
converter.
2 Study and obtain waveforms of 3 phase half controlled bridge converter
with R and RL loads.
3 Study and test the firing circuit of 3-phase full controlled bridge converter.
4 Study and obtain waveforms of 3-phase full controlled bridge converter
with R and RL loads.

5 Study and test 3-phase AC voltage regulator.
6 Control speed of dc motor using 3-phase half controlled bridge converter.
Plot armature voltage
versus speed characteristic.
7 Control speed of dc motor using 3-phase full controlled bridge converter.
Plot armature voltage versus speed characteristic.
8 Control speed of a 3-phase induction motor in variable stator voltage mode
using 3-phase AC
voltage regulator.
9 Control speed of universal motor using AC voltage regulator.
10 Study 3-phase dual converter.
11 Study speed control of dc motor using 3-phase dual converter.
12 Study three-phase cycloconverter and speed control of synchronous
motor using cycloconverter.
13 Control of 3-Phase Induction Motor in variable frequency V/f constant
mode using 3-phase
inverter.
8EE7 HIGH VOLTAGE ENGINEERING LAB
1 Study filtration and Treatment of transformer oil.
2 Determine dielectric strength of transformer oil.
3 Determine capacitance and dielectric loss of an insulating material using
Schering bridge.
4 Study solid dielectrics used in power apparatus.
5 Study applications of insulating materials.
6 Study direct testing and indirect testing of circuit breakers.

7 Study high voltage testing of electrical equipment: line insulator, cable,
bushing, power
capacitor, and power transformer.
8 Design an EHV transmission line.

Syllabus

More Related Content

What's hot (20)

Similar to Syllabus (20)

Syllabus