Experiment 5

Introductory Electronics Laboratory
5-i
Experiment 5
Resonant circuits and active filters
SECOND-ORDER SYSTEMS AND RESONANCE 5-2
LC resonant amplifier..................................................................................................................................... 5-2
Transient response of a high-Q resonant circuit............................................................................................ 5-4
POSITIVE FEEDBACK IN LINEAR APPLICATIONS 5-5
Stability of linear circuits which include positive feedback............................................................................ 5-5
A negative impedance circuit......................................................................................................................... 5-6
The gyrator .................................................................................................................................................... 5-7
The Howland Current Pump........................................................................................................................... 5-9
INTRODUCTION TO SECOND-ORDER ACTIVE FILTERS 5-11
Resonant circuits as filters........................................................................................................................... 5-11
Filter types: choosing the right Q................................................................................................................. 5-12
A very simple VCVS active filter ................................................................................................................... 5-13
Other active filter circuit topologies; the state-variable filter ..................................................................... 5-15
PRELAB EXERCISES 5-18
LAB PROCEDURE 5-19
Overview...................................................................................................................................................... 5-19
Negative impedance circuit ......................................................................................................................... 5-19
Amplifier-filter using the VCVS architecture ................................................................................................ 5-19
State-variable (UAF) filter............................................................................................................................ 5-19
Additional Circuits........................................................................................................................................ 5-19
Lab results write-up ..................................................................................................................................... 5-19
MORE CIRCUIT IDEAS 5-20
Sallen-Key low-pass filter............................................................................................................................. 5-20
A simple nonlinear amplifier........................................................................................................................ 5-21
Sine-wave oscillators ................................................................................................................................... 5-22

Experiment 5
5-ii
Copyright © Frank Rice 2013 – 2015
Pasadena, CA, USA
All rights reserved.

5-1
Experiment 5
Resonant circuits and active filters
Now we return to the realm of linear, analog circuit design to consider the final major topic
of the term regarding linear op-amp circuits: linear, second-order systems, which include
resonant circuits and active filters — two-port networks in this category have transfer
functions which are described by linear, second-order differential equations.
First we consider the archetypical resonant circuit: the LC resonator (inductor + capacitor).
We use this circuit to define the resonant frequency and quality factor for a second-order
system, and we investigate the frequency and transient responses of a high-Q, tuned circuit.
Next we switch topics to investigate how a bit of positive feedback may be added to our
repertory of linear op-amp circuit design techniques. We start by considering a negative
impedance circuit which employs mild amounts of positive feedback in conjunction with
negative feedback. This sort of circuit is found in a wide variety of linear op-amp
applications including amplifiers, gyrators (inductance emulators constructed from op-amps
using only resistor and capacitor feedback networks), current sources, and, in particular,
resonant circuits and sinusoidal oscillators.
Finally, we introduce the topic of second-order filters starting, naturally enough, with our
friend the LC resonant circuit, but this time with an added resistor (a dissipative element) to
lower the Q to around 1. In this way we can investigate the behavior of second-order low-
pass, high-pass, and band-pass filters. We then implement such filters using linear op-amp
circuits containing only RC combinations in their feedback networks, eliminating the need
for costly and hard-to-find inductors. We discuss some of the tradeoffs when selecting the Q
to use in a second-order filter, and look at Bessel and Butterworth designs in particular.
As a postscript, the More circuit ideas section presents a couple of sinusoidal oscillators
constructed from resonant circuits.

Experiment 5: Second-order systems and resonance
5-2
SECOND-ORDER SYSTEMS AND RESONANCE
LC resonant amplifier
Consider the inverting amplifier circuit in Fig-
ure 5-1; assume for the moment that the op-
amp is ideal. Note that the feedback impedance
is given by the parallel combination of an in-
ductor L and a capacitor C; in addition there is
a resistance to which we assign the value
LCQZ , where Q is a dimensionless real number
and LCZ is an impedance (actually a re-
sistance) which we will soon define. The gain
of the amplifier will be, of course, given by the
ratio of the feedback and input impedances,
f iG Z R= − . The parallel elements combine
to create a feedback impedance of:
1 1 1
LCf
j C
Z j L QZ
ω
ω
= + +
if 2
LCω−
= , the two imaginary terms in the
expression for fZ cancel, and at that frequency just the resistance remains, so LCfZ QZ= .
This one frequency at which fZ is real is called the resonant frequency of the LC
combination, LCω . Although the impedances of the L and C cancel at LCω , neither one is
equal to 0; in fact, the magnitude of each is equal to the characteristic impedance of the LC
combination, LCZ L C= . The quality factor, Q, is thus the ratio of the resistance in parallel
with the L and C to the characteristic impedance LCZ .
Using the LC resonant frequency LCω and characteristic impedance LCZ , the gain of the
inverting amplifier may be written as:
5.1
1
LC
LC
LC
iZ R
G
j
Q
ωω
ω ω
−
=
 
− + 
 
; LC
L
Z
C
= ,
1
LC
LC
ω =
Figure 5-2 shows Bode plots of the magnitude and phase of equation 5.1 for 50Q = . If 1Q >
then far from the resonant frequency fZ is dominated by either the impedance of the L or
the C, and the asymptotic responses (shown by the diagonal dashed lines in Figure 5-2)
intersect at LCω with gain LC iG Z R= . The phases of the two asymptotes have opposite
signs, however, and at LCω their contributions to the gain cancel, leaving only the parallel
resistance to determine the gain. Thus the gain magnitude and phase change very rapidly near
Figure 5-1: An inverting amplifier with a parallel
LC combination forming the feedback imped-
ance. In addition the circuit will include an
equivalent parallel resistance along with the L
and C. Its equivalent value QZLC is addressed in
the text.
iR
LCQZ
C
L
inV
outV

5-3
LCω , where the denominator of the gain function in expression 5.1 changes by a factor of Q
within a narrow range of frequency of order LC Qω (lower pair of plots in Figure 5-2). This
behavior is characteristic of the phenomenon of resonance. Because the denominator of 5.1
is quadratic in the angular frequency ω, the circuit in Figure 5-1 is an example of a second-
order system.
Figure 5-2: Bode plots of the inverting LC resonant amplifier for Q = 50. The gain magnitude is
normalized to GLC = ZLC/Ri. Note that the asymptotic gain lines intersect at ωLC with G = GLC, but the
actual gain at ωLC is Q times larger. Note that the phase plots have been “unwrapped” so that they
remain continuous as the phase passes through −180° at resonance.
The lower plots show details of the response near ωLC. If Q is large, then the −3dB gain points are
separated by Δω-3dB/ωLC = 1/Q (±1% around ωLC in this example); the phase changes by 90° in this
same small frequency range.

Experiment 5: Second-order systems and resonance
5-4
Transient response of a high-Q resonant circuit
Recall that because the gain is the ratio of the output and input voltages, equation 5.1 can be
written as
2
1 LC
LC LC LC
out out out in
i
Zj j jV V V V
Q R
ω ω ω
ω ω ω
 
+ =−+ 
 
This frequency-domain expression may be transformed to the time-domain by replacing jω
with a time derivative; thus the gain expression (5.1) corresponds to the second-order, linear
differential equation
5.2 2
1 1 1 ( )LC
LCLC LC
out out out in
i
Zv v v v f t
Q R ωω ω
•• • •
−+ = =+
If 1 2Q > , the homogeneous solution of (5.2) takes the form of a damped harmonic
oscillation:
5.3 ( )2
( ) cosLC
T
t Q
outV t e tω
ω φ−
∝ + ; ( )2
1 1 4T LC Qω ω= −
This ringing following a sudden transient input will persist for many cycles if Q is large;
after Q cycles the ringing amplitude will still be about 4% of its starting value (see Figure
5-3).
Figure 5-3: First 25 cycles of the output ringing of the circuit in Figure 5-1 for Q = 50. A negative step
in the input would excite this response; the ringing initial amplitude would be approximately ZLC/Ri
times the input step amplitude.
High-Q resonant circuits such as this are useful to selectively amplify a very specific, narrow
band of frequencies, such as when a radio receiver is tuned to a particular transmitter’s
frequency; for this reason they are sometimes called tuned circuits. Note that changing the
input or the resonant frequency of the circuit must be followed by a waiting period of several
Q’s of cycles for the circuit’s ringing in response to the change to largely dissipate — high-Q
tuned circuits have a relatively long settling time.
Note that if a resonant circuit’s Q were infinite, the ringing would persist indefinitely — we
would have a sine-wave oscillator. This feat may be accomplished by a judicious use of
positive feedback in our linear, resonant system to maintain the sinusoidal output. Sine-wave
oscillators are discussed in MORE CIRCUIT IDEAS: Sine-wave oscillators on page 5-22.

5-5
POSITIVE FEEDBACK IN LINEAR APPLICATIONS
Stability of linear circuits which include positive feedback
The hallmark of linear op-amp circuits is their use of negative feedback to maintain the two
op-amp inputs at the same voltage, as described all the way back in Experiment 1. When we
used positive feedback in Experiment 4 it was to create a Schmitt trigger, a highly nonlinear
circuit in which the op-amp output spends its time in either positive or negative saturation
(except during those brief, slew-rate limited transitions from one saturation limit to the
other), and the two op-amp inputs are generally at very different voltages.
In this section we consider linear, analog circuits
which, nevertheless, include a bit of positive
feedback along with a strong dose of negative
feedback. By using this technique we can design
analog circuits with a greatly expanded range of
capabilities, as we shall soon see. Consider the
generic analog op-amp circuit shown at right. The
feedback network is constructed from of a set of
four impedances forming voltage dividers from outV
back to both the op-amp’s +Input and –Input. Call
the fraction of outV fed back to these two op-amp
inputs f+ and f− , respectively; for this example
( )i i ff Z Z Z+ + + += + , ( )i i ff Z Z Z− − − −= + .
At zero frequency (DC), both f+ and f− are nonnegative real numbers, so as long as
f f− +> , the net feedback will be negative, and the circuit will remain stable and linear (note
that we must include the output impedance of the source for inV when calculating f+ and
).f− At other frequencies, the stability criterion is a little more subtle: one must find the set
of solutions s jω= of the equation:
5.4 ( ) ( ) 1 ( ) 0f j f j g jω ω ω− +− + =
where ( )g jω is the open-loop gain function of the op-amp (as described in Experiment 2).
We replace all occurrences of jω in (5.4) with the complex variable s and then find the
complex solutions s of (5.4). If the real parts of the various solutions of (5.4) are all negative,
i.e. Re( ) 0s < for all roots s of this equation, then the circuit will be stable. Proof of this
criterion is left to the exercises (just kidding!). Actually, proof of this theorem belongs to the
general field of control system engineering.
The criterion expressed above always gives a correct assessment of a feedback circuit’s
stability, and it is generally the best way to evaluate our systems. A simpler, more naïve
Figure 5-4: Generic inverting amplifier with
some positive feedback as well.
inV outV
iZ − fZ −
fZ +
iZ +

Experiment 5: Positive feedback in linear applications
5-6
criterion is usually adequate for our elementary circuits, and it is more intuitive and easier to
apply:
Stability criterion when including positive feedback
As long as the fraction of the output fed back through the negative feedback loop is
greater than the fraction fed back through the positive feedback loop, then the
circuit will probably remain stable and predictable.
This criterion must hold at all frequencies for which the circuit is capable and for all
inputs and loads the circuit may encounter.
A negative impedance circuit
With this stability criterion in mind, consider the circuit in Figure 5-5, a one-port network
driven by a source with output impedance sZ , as shown. What we are interested in is to
determine the circuit’s input impedance, in in inZ V I= , and to decide how the op-amp’s +
and – input terminals should be connected in order to ensure the circuit’s stability.
Figure 5-5: A negative impedance circuit. As explained in the text, the input impedance of the op-
amp circuit, Vin/Iin , is –Z, the negative of the impedance of the element Z in the circuit. The “?” on
the op-amp symbol implies that we must carefully consider how the op-amp’s inputs should be
connected — with –Input at top as shown, or should the op-amp’s inputs be flipped? This issue is
discussed in the text.
If we assume that the stability criterion is satisfied, i.e. that there is net negative feedback
around the op-amp, then we can assume that the ideal op-amp’s +Input and –Input voltages
are equal. This means that the input voltage inV appears at both op-amp inputs, and,
therefore, that inV must be the voltage drop across the impedance Z (since its other end is at
ground). The resulting current through Z ( ZI in the figure) must come from the op-amp
output by flowing through the feedback resistor. The voltage drops across the two resistors R
in the figure are the same, i.e. out inV V− , so current ZI must also flow through the top
outV
inV
Z
R
RsZ
sV
inI
ZI
?
Z−
inV
ZI

5-7
resistor R from the op-amp output toward the input terminal of the circuit. Thus ZinI I= − !
Therefore:
5.5 Zin in in inZ V I V I Z= =− =−
The circuit’s input impedance is the negative of the impedance Z — we have a device with a
negative impedance to ground. Thus, for example, if the impedance Z is a simple resistor,
then when we apply a positive voltage to the circuit’s input, the circuit will push current back
into the source; it would be a source of power rather than an absorber of power (of course,
the power comes from the op-amp power supplies).
Before we consider how to use this circuit for something interesting, we must make sure that
our original assumption is correct: is the stability criterion satisfied? We must check that
there is less output feedback to the op-amp’s +Input than to its –Input. Since the two
feedback resistors each have value R in Figure 5-5, the feedback fraction will depend on the
impedance to ground at each op-amp terminal, since that impedance will set the voltage
divider ratio at that terminal. For the –Input terminal in Figure 5-5 this is the impedance Z;
the impedance to ground at the op-amp’s +Input is the output impedance of the driving
source, sZ .
Thus for the configuration shown in Figure 5-5, the stability criterion requires that
sZ Z< at all frequencies the op-amp can amplify. If the opposite were true, i.e.
sZ Z> , then the inputs to the op-amp should be reversed.
Now let’s consider a simple application of our negative impedance circuit: a
voltage divider which includes a “resistor” with a negative value, as shown at
right. The gain of this circuit is 2 1 2( )out inV V R R R=− − , which has a
magnitude greater than 1 if 1 22R R< . We could build this sort of amplifier
using our negative impedance circuit to realize the negative resistance 2R ; we
just have to be careful as we consider the stability criterion in this case.
The gyrator
An interesting application of the negative impedance circuit is to try to find a more
complicated circuit using it which inverts an impedance: 1Z Z→ ; then we could emulate
an inductor using a capacitor (1 )j C j Cω ω→ . Such a device is called a gyrator. A circuit
which accomplishes this task using voltage dividers and our negative impedance circuit is
shown in Figure 5-6 on page 5-8. Working out that this circuit does indeed invert the
impedance Z is left as an exercise to the reader. What is more problematic, however, is to
decide how to orient the op-amps’ inputs and apply the stability criterion to this circuit.
1R
2R−

5-8
Figure 5-6: A simple gyrator built from nega-
tive impedance converter circuits. Deciding
how to orient the op-amp inputs could be a
problem, however.
A more sophisticated application of combined positive and negative feedback to implement a
gyrator circuit is shown in Figure 5-7. This circuit is quite different from the negative
impedance circuit, and it is quite stable, though we won’t consider its stability in detail here.
Figure 5-7: A practical gyrator circuit. The op-amps will maintain their inputs at the same potential,
so the voltage across Z5 and the voltage at the junction of Z2 and Z3 must both equal the input
voltage. With this condition it is straightforward to derive the input impedance formula shown.
Assuming that the op-amps are ideal and working linearly and correctly, then their inputs
must all be at the same potential, which must be the input voltage, since an op-amp input is
connected there (Figure 5-7). With this constraint plus the observation that the current
R
Z
R R
2
inZ R Z=
1Z
2Z
3Z
4Z
5Z
51 3
2 4
in
Z Z Z
Z
Z Z
=

5-9
through 2Z must equal that through 3Z , and similarly for the currents through 4Z and 5Z , it
is straightforward to show that the circuit’s input impedance is given by the expression
included in the figure.
The conventional way to emulate an inductor with the gyrator circuit in Figure 5-7 is
to use a capacitor for 4Z and resistors for the other impedance elements.
The Howland Current Pump
Another interesting linear op-amp circuit employing both
positive and negative feedback is the Howland Current
Pump, invented many years ago by Bradford Howland at
MIT. This circuit is an example of a voltage to current
converter: it establishes a constant current through a load
which is proportional to a control voltage input to the
circuit.
First, however, consider the simple circuit in Figure 5-8,
originally introduced in Experiment 1. In this case the
load element is positioned in the op-amp’s negative
feedback loop. Because the two op-amp input voltages are equal, the supplied input voltage
inV also appears across the resistor R. The op-amp output current required to establish this
voltage across R must pass through the load, so the load current is set to inLoadI V R= , and it
will be independent of any variation in the load’s impedance.
A significant drawback of the simple circuit of Figure 5-8, however, is that its load must
float: the load’s two terminals must both be independent of the circuit ground. A more
common requirement which our simple circuit can’t satisfy is to supply a fixed current into a
single terminal of a load that itself might be part of a complicated sub-circuit; the injected
current would then be returned through the system ground or power supplies. The Howland
Current Pump shown in Figure 5-9 on page 5-10 provides an elegant solution to this design
problem.
To understand how this circuit operates, we will analyze it in two stages: (1) determine the
load current LoadI when the load impedance is 0, i.e. the circuit is connected directly to
ground at that point; (2) show that the load current is independent of any variation in the load
voltage Load Load LoadV Z I= . In any case, since the ideal op-amp inputs draw no current, it
must be true that the load current is given by 1 2LoadI I I= + (see Figure 5-9).
Let us therefore first consider the case (1) in which the output of the circuit goes directly to
ground ( 0)LoadZ = and determine the two currents 1I and 2I . Since the output node is now a
circuit ground, the op-amp +Input is grounded, and the op-amp circuit becomes a simple
Figure 5-8: A simple voltage to
current converter: ILoad = Vin /R.
LoadI
inV
R

5-10
inverting amplifier with out inV V −= − . Now the voltages inV + and outV appear across the
resistances R, determining currents 1I and 2I . Thus the load current is given by:
5.6 1 2 ( )in inLoadI I I V V R+ −= + = −
Next consider the effect of a change in the load voltage on the load current. Because the
circuit is linear, we can use the principle of linear superposition presented in Experiment 1.
Thus we consider the case where 0in inV V+ −= = , and ask how LoadI depends on LoadV , which
is the voltage at the node connected to the op-amp’s +Input. Since the terminal at inV − is now
ground, the op-amp circuit is a noninverting amplifier for the voltage at its +Input, and
2out LoadV V= . Since the terminal at inV + is also ground, the voltage drop across the bottom-
left resistor is LoadV , and 1 LoadI V R= − . The voltage drop across the bottom-right resistor is
out Load LoadV V V− =, so 2 LoadI V R= . This means that 1 2 0LoadI I I= + = , so the load current
is unaffected by the load voltage. Therefore equation 5.6 is correct regardless of the load
voltage and, thus, is independent of the load impedance LoadZ . The Howland Current Pump
serves as a current source whose output current is programmed by the differential input
voltage in inV V+ −− according to equation 5.6.
Figure 5-9: The Howland Current Pump
supplies a current into a terminal of a
grounded load which is independent of the
load’s impedance. The load current is given
by equation 5.6; its operation is described in
the text.
inV −
inV +
outV
LoadI
R R
R R
1I 2I
LoadZ

5-11
INTRODUCTION TO SECOND-ORDER ACTIVE FILTERS
Resonant circuits as filters
High-Q resonant circuits with responses similar to that shown in Figure 5-2 on page 5-3 are
useful for the narrow-band, high gain filters needed in radio-frequency tuning circuits. For
many applications, however, one needs low-pass and high-pass filters with a relatively flat
pass-band response and a rapid reduction in gain (roll-off) as the signal frequency moves
beyond the filter’s cut-off frequency. A second-order resonant circuit with a modest Q
( 1)Q< provides a solution which offers a flatter frequency response in the pass-band, a more
dramatic out-of-band roll-off, and a faster settling time than you can achieve using the
simple, first-order RC filters discussed in Experiment 2. As a set of simple examples
reminiscent of our first-order RC filters, consider the series LCR circuits configured as
voltage dividers in various ways shown in Figure 5-10.
Low-pass Band-pass High-pass
Figure 5-10: Series LCR circuits configured as simple filters. By forming a voltage divider and taking
the output from the voltage across each of the various elements, various filter responses may be
achieved. In each case the resonant frequency is, of course, ω0 = 1/LC; the quality factor Q = ZLC/R.
For each of the circuits above, the transfer function will have a denominator (D) like that of
the gain function in equation 5.1, namely:
5.7 0
0
1D j
Q
ωω
ω ω
 
≡ − + 
 
; 0
1
LC
ω = ,
L C
Q
R
=
These are called second-order filters because ( )D ω is quadratic. At 0ω , 1 D Q= . The
numerators for the various LCR filters depend on the bottom element used in the voltage
divider (each numerator is given by ( ) LCZ Zω , where ( )Z ω is the impedance of the bottom
element and )LCZ L C≡ . The resulting transfer functions for these three filters are plotted
in Figure 5-11.

Experiment 5: Introduction to second-order active filters
5-12
Low-pass Band-pass High-pass
0( )G j Dω ω= (1 )G Q D= 0( )G j Dω ω=
Figure 5-11: Transfer functions and Bode gain plots for the second-order filters of Figure 5-10 for Q
2
= 1/2. The −3dB gain points for the band-pass filter are at 0.52ω0 and 1.93ω0; for the others it is at
ω0. The out-of-band filter slopes are ω
−2
, ω
±1
, and ω
+2
. The denominator D in the gain formulas is
defined in equation 5.7.
A second-order filter with 1 2Q = (such as those plotted above) is an example of a
Butterworth filter, a good choice for a general-purpose filter.
Filter types: choosing the right Q
If one were to simply cascade two first-order low-pass filters with the same cutoff frequency
(as in the case of the two cascaded, gain-11 amplifiers evaluated in Experiment 2), then their
combined response would be equivalent to a second-order filter with 1 2Q = . Such a
response is characteristic of a critically damped second-order system, and this behavior is
often sought for by control system engineers. For the purposes of signal filtering, however,
such a low Q system may sacrifice a bit too much in the way of frequency response, because
its attenuation (roll-off) at its −3dB corner frequency is quite gradual (soft), and the filter
introduces significant phase shifts at frequencies far from the corner. A high-Q response, on
the other hand, may have a steep roll-off at its −3dB corner frequency, but it will exhibit
severe gain peaking near its resonant frequency and will show a lot of ringing in response to
a transient input. Making a choice of Q which results in the best compromise of gain flatness
and phase shift in the pass-band, steepness of the roll-off at the −3dB frequency, and
transient response is often a difficult one and will depend on your specific application. In this
section we give examples of some popular choices designers typically consider.
The most popular choice for a second-order filter is probably the Butterworth filter, named
after the British physicist Stephen Butterworth and characterized by 1 2Q = (as with the
filters in Figure 5-11). It is called the maximally-flat low-pass filter because the second
derivative of its transfer function vanishes only at 0 frequency, making it the highest Q
second-order low-pass filter with a monotonically decreasing gain as frequency increases
(i.e. no gain peaking or pass-band gain ripple). Its −3dB corner frequency is also its resonant
frequency, 0ω .

5-13
A less common choice is the Bessel filter, with 1 3Q = . Its lower Q places its −3dB
corner frequency is at 00.79ω , and the filter roll-off near its −3dB frequency is softer than
the Butterworth (see left-hand graph in Figure 5-12 below). The advantage of the Bessel
filter for certain applications, however, is that it has constant group delay for frequencies
well within its pass-band, implying that it will cause the least distortion to the shape of a
complicated waveform.
Frequency response Step-input response
Figure 5-12: Frequency and transient responses of various 2
nd
order low-pass filters. All filters have
the same −3dB frequency, but have different Q’s (the Butterworth filter has legend “Btwrth”). The
critically damped filter has Q = 1/2. The Q = 1 filter has mild gain peaking (+1.25 dB), but significant
step response overshoot; its resonant frequency is 0.79 of its −3dB corner frequency.
The critically damped filter ( 1 2Q = ) mentioned previously has its −3dB corner frequency
at only 00.64ω , and the filter roll-off there is very soft. It has the distinction, however, of
having the highest Q for which its transient response to a step input has no overshoot; its
output settles following a step input more rapidly than for any other second-order filter with
the same −3dB corner frequency (right-hand graph in Figure 5-12), although its resonant
frequency must be made nearly 60% higher than that of an equivalent Butterworth filter.
A very simple VCVS active filter
The main drawback of an LCR filter is that it requires a high-quality inductor as one of the
filter elements. This may not be a problem for a filter designed to operate at several MHz, but
for frequencies below a few MHz your choice of suitable inductors may be limited (and such
inductors are relatively expensive). Consequently, an active filter implemented using op-
amps with RC feedback networks is the more practical solution for a low-frequency filter. A
gyrator circuit (Figure 5-7) may be used to emulate the inductor, but only if the circuit has
one terminal of the inductor connected to ground (only the high-pass series LCR filter
discussed previously meets this requirement). Fortunately, electronics designers have

5-14
invented several op-amp circuits employing both positive and negative feedback which
implement quite effective second-order filters. In this section we discuss one of these, the
Voltage-Controlled Voltage Source (VCVS) active filter.
A simple VCVS circuit for a second-order low-pass filter is shown in Figure 5-13. It is clearly
a cascaded pair of simple RC filters followed by a noninverting op-amp gain stage. The
wrinkle to this circuit, however, is that the first RC filter stage is terminated not by grounding
its capacitor but by connecting it to the amplifier output, providing some positive feedback
(also called bootstrapping). This clever change makes the filter’s Q as well as its resonant
frequency 0ω adjustable by selecting the appropriate component values and amplifier gain A.
Rather than analyze the general case where the component values and amplifier gain are all
arbitrary, we consider only the special case where both resistors and both capacitors are
chosen to have equal values R and C. In this special case the transfer function of the circuit
is:
Simplified VCVS low-pass filter (Figure 5-13)
5.8 2
2
0 0
1
A
G
j
Q
ω ω
ω ω
=
− +
; 0
1
RC
ω = ,
1
3
Q
A
=
−
The circuit is called a VCVS filter because the op-amp stage acts as a voltage-controlled
voltage source (which is just another way of saying that its output voltage is a function of its
input voltage, and that its output impedance is small). Examining the circuit should make it
clear that its gain at very low frequency, in which case the capacitors’ impedances get very
large, should approach that of the noninverting amplifier stage, A. Not as clear, perhaps, is
that the positive feedback stability criterion on page 5-6 will demand that 3A < (note from
Figure 5-13: A simple version of the VCVS second-order, active low-pass filter, in which both the
resistors and the capacitors of the two cascaded RC filters are chosen to be equal. The non-
inverting op-amp amplifier stage has gain A (if a simple voltage follower is used, so A = 1, then the
circuit is called a Sallen-Key filter). The circuit’s resonant frequency is ω0 = 1/RC, and its Q =
1/(3−A). The circuit’s in-band gain is A.
Gain = A
R
C C
R
inV
outV

5-15
the equations 5.8 that Q → ∞ as 3).A → If the resistor and capacitor values are not well-
matched, then the circuit’s 0ω and Q will vary a bit from the expressions in 5.8.
High-pass and band-pass versions of the simple VCVS filter are shown in Figure 5-14. If
1A = (i.e. a voltage follower is used for the noninverting op-amp stage), then the circuit is
called a Sallen-Key filter after its inventors at the MIT Lincoln Laboratory in 1955. The
section MORE CIRCUIT IDEAS: Sallen-Key low-pass filter on page 5-20 shows how to design
such a filter.
High-pass Band-pass
Figure 5-14: Other VCVS second-order filters. As with the low-pass filter, the filters’ ω0 = 1/RC, and
Q = 1/(3−A). The in-band gain of the high-pass filter is A; the band-pass filter’s gain at ω0 = QA. Note
that one resistor in the band-pass version of the filter has value 2R.
Other active filter circuit topologies; the state-variable filter
Another common second-order active filter which uses
only a single op-amp is the multiple-feedback (MFB)
design, which is most useful for high-Q or high-gain
filter stages. A low-pass version of the circuit is shown in
Figure 5-15; to get a high-pass design, simply swap the
resistors and capacitors in the circuit. Note that this is an
inverting amplifier (the pass-band gain is 2 1R R− ) and
that the op-amp is configured as an integrator. We won’t
discuss this filter any further; you can find several
references for designing this type of filter in the lab
library or on the web.
A more flexible design than either the VCVS or MFB topologies is the second-order state-
variable filter shown in Figure 5-16, which is from the Texas Instruments ASLK Pro
Manual, page 32; that document’s Experiment 5 shows how to convert this circuit to a
voltage-controlled filter. Although this filter uses 4 op-amps, it simultaneously provides low-
pass, band-pass, high-pass, and band-stop filter outputs, and its pass-band gain A and its Q
are easily adjustable. Note that the circuit topology is formed from a cascade of two inverting
integrators and a gain −1 inverting summing amplifier whose output is fed back to become
Gain = A
R
C C
R
Gain = A
R
C
C
2R
R
Figure 5-15: Multiple-feedback
low-pass filter circuit.
1R
2R

5-16
the input to the first integrator. To this basic loop is added a feed-forward section around the
second integrator — the input signal is summed with the output of the first integrator in this
section.
Figure 5-16: A Universal Active Filter (UAF), a form of second-order, state-variable active filter. This
design is from the Texas Instruments ASLK Pro Manual, ©Texas Instruments, 2012. It
simultaneously provides high-pass (HP), low-pass (LP), band-pass (BP), and band-stop (BS) outputs.
The pass-band filter gain is A; its resonant frequency is ω0 = 1/RC.
The resonant frequency is, naturally, 0 1 RCω = .
The gain in the pass-band of the low-pass, high-
pass, and band-stop filters is A, which from Figure
5-16 is just the gain for the input signal of the
summing amplifier at the bottom of the figure; the
gain of the band-pass filter at 0ω is QA. Q is simply
the reciprocal of the gain of the feed-forward signal
from the first integrator through this same summing
amplifier. The response of the band-stop filter is
shown at right.
You can see how the state-variable filter works by
first reviewing Figure 5-11 on page 5-12. Starting
with the high-pass filter’s response function in that
figure, note that you can obtain the response functions of the band-pass and low-pass filters
by successive divisions by 0jω ω . But this is the same as integrating in the time-domain, so
clearly the successive integrators in the state-variable filter loop (Figure 5-16) convert the
high-pass output to band-pass and low-pass outputs, as long as 0 1 RCω = . Now with a little
bit of arithmetic and keeping in mind that the amplifiers are all inverting, you should be able
to show that the two summing amplifiers combine the low-pass, band-pass, and input signals
R
C CR R R
R
QR
R A
R
inV
outV outV outV
outV
(LP)(BP) (HP)
(BS)
Figure 5-17: Band stop filter response.

5-17
in just the right way to generate the high-pass response. Note that the input impedance of the
filter is equal to the single input resistor value ;R A you may need to add a voltage follower
to the input to obtain a large input impedance.
If you need to be able to easily and independently adjust the gain or Q of a second-order
active filter or if you need multiple filter outputs to split an input signal into frequency
sections, then the state-variable filter is a good choice.
The state-variable filter is really only suitable for filters with a modest Q of 2 or less
(which is by far the most commonly encountered requirement); otherwise extremely
good component matching of the various Rs and Cs may be necessary, especially for
the band-stop filter output.

Experiment 5: Prelab exercises
5-18
PRELAB EXERCISES
1. Consider the voltage divider with a negative
impedance circuit as one “element” shown in
Figure 5-18 at right.
a. What is the gain ( out inV V )?
b. Which way should the op-amp’s inputs be
oriented (+Input at top or –Input at top)?
(assume that the source of inV is a perfect
voltage source and the load at outV has
infinite input impedance)
c. What are the divider’s input and output
impedances (assume that the source of inV is
a perfect voltage source and the load at outV
has infinite input impedance)?
d. If 1.0VoutV = , then what is the voltage at the op-amp output?
2. Consider the Howland current pump shown in Figure 5-9 on page 5-10. What is the op-
amp output voltage outV in terms of the input and load voltages inV − , inV + , and LoadV ?
3. Sketch the phase response Bode plots to go with each of the gain magnitude plots shown
in Figure 5-11 on page 5-12 for the LCR filters shown in Figure 5-10.
4. Consider the simple VCVS low-pass filter in Figure 5-13 on page 5-14. What should be the
ratio of the two resistors of the noninverting amplifier (i.e. ifR R ) if you want a
Butterworth filter response?
5. Design a cascaded amplifier-filter circuit which has a pass-band gain = 10 and has a
Butterworth low-pass filter response with a –3dB corner frequency of 16kHz. Use a VCVS
circuit for the low-pass filter (Figure 5-13 on page 5-14).
Circuit specifications:
Input impedance: 1MegΩ
Pass-band gain: 10 (noninverting)
Filter spec: Butterworth low-pass, –3dB corner frequency of 16kHz
When you cascade the amplifier and filter, should you put the amplifier or the filter first?
Which of the above specifications will most strongly influence your choice?
Hints for resistor selections: 3.3k 5.6k 0.59= ; 27k 5.1k 5.3= .
Figure 5-18: A voltage divider with a nega-
tive impedance (boxed circuit).
?
inV outV
1k
1k
4.7k
2.2k

5-19
LAB PROCEDURE
Overview
During lab you will take a quick look at an amplifier using a negative impedance circuit as
part of a voltage divider. Next, you will construct the amplifier-filter you designed as part of
the prelab exercises. Finally, you will investigate the capabilities of the state-variable filter
architecture.
Negative impedance circuit
Construct the amplifier with a negative impedance circuit shown in Figure 5-18 using your
solution to Prelab Exercise 1 as a guide. Measure its gain and compare with your
calculations.
Amplifier-filter using the VCVS architecture
Construct the amplifier-filter circuit you designed (Prelab exercise 5) in the breadboard area
using a supplied TL082 dual op-amp IC (refer to the TL082 data sheet , page 3 for the IC
pin-out — make sure you look at the pin-out for the correct IC!).
Use the Frequency Response application to plot the frequency response of your circuit. Next,
input a square wave and use the oscilloscope to investigate the filter’s transient response to a
step input. Compare your results to the graphs in Figure 5-12 on page 5-13.
State-variable (UAF) filter
Using an additional TL082 IC, now construct a UAF with a 16kHz resonant frequency as in
Figure 5-16 on page 5-16. Initially choose a Q of 1 and a pass-band gain A of 1 for
component selections. You should be able to reuse the same RC pairs you used for the VCVS
filter for the two integrator sections of the circuit. Check the frequency responses of each of
the filter’s four outputs. Check the transient response of the low-pass filter output.
Now, by changing the value of the appropriate resistor, increase the Q to approximately 10
and look again at the outputs’ frequency responses, especially that of the band-stop (notch)
filter. Check the low-pass filter’s transient response.
Additional Circuits
If you have time, construct a circuit from the MORE CIRCUIT IDEAS section, from an earlier
experiment, or one of you own design; the Wien bridge oscillator shown in Figure 5-22 on
page 5-24 is an interesting choice.
Lab results write-up
As always, include a sketch of the schematic with component values for each circuit you
investigate, along with appropriate oscilloscope screen shots.

Experiment 5: More circuit ideas
5-20
MORE CIRCUIT IDEAS
Sallen-Key low-pass filter
The simplified VCVS filter presented earlier (Figure 5-13 on page 5-14) with equal Rs and
Cs in the cascaded low-pass filters is rather inflexible, since the gain of the amplifier must be
chosen to give the required Q. It is often desirable for the filter’s pass-band gain to equal 1,
so that the amplifier configuration used is just a simple voltage follower. In this case one gets
the standard Sallen-Key low-pass filter shown in Figure 5-19. The resistors and capacitors
now generally need to have unequal values as indicated in the figure by the ratios ρ and κ.
Figure 5-19: Sallen-Key low-pass filter. By using a voltage follower for the VCVS amplifier, the pass-
band gain of the filter is unity; the ratios ρ of the resistors and κ of the two capacitors are chosen
to select the filter’s Q and resonant frequency ω0.
The relationships between the filter’s 0ω and Q and these component value ratios are given
by:
5.9 0
1
RC
ω
κρ
=
1
Q
κρ
ρ
=
+
Because the selection of capacitor values is generally more limited than that for resistors, one
usually picks a convenient capacitor ratio such as 10κ = . With this choice the resistor value
ratio is determined from the required Q:
2 2 2
(5 1) (5 1) 1Q Qρ= − ± − −
Clearly, the resistor value ratio ρ must be real and positive, so the argument of the square
root must be nonnegative; thus the choice 10κ = will be valid only for 5 2Q ≤ . This
requirement is easily met by any reasonable filter Q (usually 1)Q < . For a Butterworth filter
response ( 1 2 )Q = ,
Sallen-Key Butterworth filter component values
5.10 0
1
10, 9 80 18 or 1 18
(0.75)RC
κ r ω= =± ≈ → ≈
Rρ ×
Cκ × C
R
inV
outV

5-21
By choosing 1 18ρ = , the filter’s corner frequency is reasonably close to 1 RC , and the
impedance of the second RC filter is quite a bit larger than that of the first, so the first RC
filter’s response is only marginally affected by the load of the second RC filter. Once you
have chosen appropriate values for the ratios κ and ρ, choose C and R to give the desired 0ω .
Many tools are available to help you design active filters. My favorite is this web-based
application available from Analog Devices:
Analog Filter Wizard
http://www.analog.com/designtools/en/filterwizard/
A simple nonlinear amplifier
In the next section we discuss the design of sine-wave oscillators, which are essentially
resonant circuits with a Q of “exactly” the point at complex ∞ when the resonator output
amplitude takes on a certain target value; if its amplitude is too large, then the Q is finite and
positive so that the output amplitude decays back to the target value, whereas if the amplitude
is too small (as when the circuit is first turned on), then the Q becomes negative, so the
amplitude increases toward the target value.
This seemingly remarkable behavior may be accomplished by using a simple nonlinear
amplifier whose gain decreases as its output amplitude rises. A noninverting version of such
an amplifier is shown in Figure 5-20.
Figure 5-20: A simple nonlinear amplifier. For large signal inputs the amplifier’s dynamic gain drops
to approximately 1, as explained in the text and as illustrated by the Vout v. Vin data shown in the
right-hand image (Ri = 1k, Rf = 2.2k for the data shown).
Here’s how the circuit works:
If the feedback current ( )in iV R is small, then the amplifier’s gain is given by the normal
noninverting amplifier formula 1 ifR R+ . As the signals get larger, the feedback current
goes up; when the voltage drop across fR approaches 0.6V, the silicon diodes begin to
outV
iR fR
inV

5-22
conduct significant current, reducing the effective feedback resistance and thus reducing the
amplifier’s gain. Since the diodes will limit the voltage drop across fR to about 0.6V as the
input signal continues to rise, we see that for large inputs outV will remain a diode drop above
inV , and the amplifier’s dynamic gain ( )out indV dV is reduced to 1≈ . This behavior is
illustrated by the outV v. inV data plotted in Figure 5-20, for 1.0kiR = and 2.2kfR = . When
the input voltage is small, the amplifier’s gain is 3.2, as indicated by the slope of the curve
near the origin. At an input voltage of 0.25V≈ , however, the slope of the curve changes
abruptly as the diodes begin to conduct (the voltage across fR is then 0.6V ). As inV
continues to increase, 1out inV V → ( 1.6out inV V ≈ for 1V)inV = .
Sine-wave oscillators
As mentioned in the section on resonant circuits, if a second-order system’s Q → ∞ , then its
transient response ringing will continue indefinitely at its resonant frequency — it has
become a sine-wave oscillator. In this section we briefly present a couple of simple sine-
wave oscillator circuits. As a first example, consider the LC resonant oscillator in Figure
5-21.
Figure 5-21: A simple LC resonant
sine-wave oscillator. Its operation is
explained in the text.
The oscillator output is taken (via
the voltage follower) from the signal
across the LC resonator, producing a
low-distortion sine-wave output,
even though the output of the
nonlinear amplifier may be quite
distorted.
Some positive feedback is required to sustain the circuit’s oscillation; in this circuit it is
generated by the voltage divider consisting of the resistor R and the parallel LC resonator.
This feedback recirculates a fraction of the output of a noninverting nonlinear amplifier back
to its input. At the resonant frequency 0 1 LCω = the impedance of the LC resonator
becomes very large: /LCQZ Q L C= ; for a good-quality resonator, we would expect
150Q  or more, and the LC component values should be chosen so that 1k-10kLCZ - . By
choosing R to be about 1/2 of this resonant impedance, the positive feedback fraction is about
outV
CL
2
LCQZ
R ≈
2
3 AV V+ ≈
AV
i fR R= fR

5-23
2/3 at frequency 0ω . At frequencies more than a couple 0 Qω away from resonance, on the
other hand, the LC impedance is LCjZ± or less, so positive feedback at any other
frequency is 1 and has a 90° phase shift.
For sustained, constant amplitude oscillation, the gain around the feedback loop, including
the amplifier, must be exactly 1. The nonlinear amplifier’s gain for a small input signal is 2
when ifR R= , so for a small signal at 0ω the loop gain is approximately 2
3 2 1× > . Thus a
small 0ω signal will grow in amplitude exponentially quickly, whereas a signal at any other
frequency will die away. As the 0ω signal’s amplitude grows, the nonlinear amplifier’s gain
will decrease until the amplitude is reached such that the loop gain is exactly unity, and the
nonlinear amplifier will stabilize its output amplitude at that value. If the feedback resistors
are each 1k, then the circuit’s output amplitude will be 1V peak.
Because the diodes act to clamp the amplifier’s peak output, the amplifier’s output will take
the form of a distorted sinusoid. The filtering action of the resonant RLC voltage divider,
however, will provide a much more pure sinusoid across the LC pair, so that is where the
oscillator’s output is taken (using a voltage follower to isolate the resonator from its load).
The distortion is minimized when the small-signal loop gain around the nonlinear amplifier
at frequency 0ω just barely exceeds 1, so trimming of the value of R may be necessary if
really low distortion is required. Unfortunately, if the small-signal loop gain were to drop
even a tiny bit below 1, then the circuit will cease to oscillate. If slightly higher distortion in
the sine-wave output is tolerable, then the diodes in Figure 5-21 may be unnecessary:
saturation of the amplifier op-amp output ( AV in Figure 5-21) will limit the oscillator’s
amplitude, but the signal at the LC resonator (where the output is taken) will still be a quite
nice sinusoid.
Very similar in concept to the LC oscillator presented above, the Wien bridge oscillator uses
RC pairs to form its resonant voltage divider as shown in Figure 5-22 on page 5-24 (a Wien
bridge-type oscillator was the first product offered by the Hewlett-Packard company, back in
1939).
The two RC pairs in the Wien bridge circuit form a resonant voltage divider to provide some
positive feedback to sustain oscillation. The resonant frequency is 0 1 RCω = , but the filter’s
Q is only 1 3 when the RC pairs are perfectly matched. The divider ratio is also 1 3 at 0ω ,
so the nonlinear amplifier must have a small-signal gain of at least 3 for the circuit to
oscillate. The diode clamping will severely distort the oscillator output if the amplifier’s
small-signal gain is even more than a few percent above 3, so some trimming of either fR or
iR will be necessary to limit the distortion in the output waveform.

5-24
Figure 5-22: The Wien bridge oscillator uses two
RC pairs to form its resonant voltage divider which
provides positive feedback to sustain oscillation.
The oscillation frequency is ω0 = 1/RC.
At ω0 the positive feedback fraction is 1/3, so the
small-signal gain of the nonlinear amplifier must
be at least 3. The resonant divider’s Q =1/3, so,
because of the diode clamping, achieving a
tolerable level of distortion will nearly always
require trimming of the ratio Rf /Ri to just above 2.
An alternative (and much better) method of controlling
the amplifier’s gain is to use an incandescent light bulb
(one with a glowing filament) in place of resistor iR as
shown at right; this is the method used in a truly low-
distortion Wien bridge oscillator. This technique was
invented by L. A. Meacham of Bell Laboratories in 1938
and was incorporated in the Hewlett-Packard product
mentioned previously. As the bulb’s filament heats up, its
resistance increases, lowering the amplifier’s gain.
Because a change in the filament temperature is gradual
(taking much longer than the oscillator’s output period), it has essentially no effect on the
output waveform shape. For our Wien bridge oscillator, the incandescent bulb used should
have a resistance when cold of about 100Ω; the amplifier’s feedback resistor should have a
value about 2.5 times higher. With this version of the oscillator’s amplifier, the output
signal’s distortion may be so low as to be very hard to measure.
There are many other designs for op-amp sine-wave oscillators. The following article by
Texas Instruments provides a nice summary and design procedures for several practical ones:
http://www.sophphx.caltech.edu/Physics_5/Useful_circuits/TI_Sine_Oscillators.pdf
outV
iR (2.1-2.2) ifR R=
R
R
C
C
Figure 5-23: An amplifier whose
gain is controlled by the tempera-
ture of the incandescent bulb used
as the op-amp’s Ri.

Experiment 5

More Related Content

What's hot (20)

Similar to Experiment 5 (20)

Recently uploaded (20)

Experiment 5