Fanuc educational cell manual

1
Education Cell
Technical Documentation for the R-30iB Plus Controller
V4.3

2
1 Contents
1 Selecting and running Example program............................................................................................... 4
1.1 Start Up Screen ........................................................................................................................... 4
1.2 Example Program “AAA_DEMO”................................................................................................ 5
1.3 AAA_DEMO Program Sequence with / without iRVision........................................................... 9
1.4 Operation Menu Display............................................................................................................ 10
1.5 4D Graphics (Option) ................................................................................................................. 11
2 Demonstration Program Setup / Teaching........................................................................................... 12
2.1 Gripper Setup............................................................................................................................. 12
2.2 UFrame 2 Setup......................................................................................................................... 13
2.3 Orient Origin Point..................................................................................................................... 15
2.4 X-Direction Point ....................................................................................................................... 16
2.5 Y-Direction Point ....................................................................................................................... 17
3 Robot Setup ............................................................................................................................................ 18
3.1 UTOOL / TCP Setup ................................................................................................................... 18
3.2 Payload Setup............................................................................................................................ 18
3.3 DCS Setup.................................................................................................................................. 19
3.3.1 DCS Tool Model. ........................................................................................................................ 19
3.3.2 DCS Safe Zone ........................................................................................................................... 20
3.4 I/O Setup .................................................................................................................................... 21
3.5 Macro Setup............................................................................................................................... 22
3.6 TP Function Key Hint Screen .................................................................................................... 23
3.7 Home / Reference Position....................................................................................................... 24
3.8 Power Up Program.................................................................................................................... 25
4 iRVision Setup ( Option )......................................................................................................................... 26
4.1 Camera Adjustment .................................................................................................................. 26
4.2 Application Frame ..................................................................................................................... 28
4.3 Camera Calibration ................................................................................................................... 29
4.4 Example iRVision Application ................................................................................................... 31
4.5 iRVision Tips .............................................................................................................................. 32
4.6 TP Program................................................................................................................................ 34
5 List of Registers ..................................................................................................................................... 35
5.1 Numeric registers ..................................................................................................................... 35
5.2 Position Registers ..................................................................................................................... 37
6 Program Details ..................................................................................................................................... 38
6.1 List of programs ........................................................................................................................ 38
6.2 Sample Program Listings ......................................................................................................... 41
7 User Interface Setup .............................................................................................................................. 43
7.1 Menu Utility Setup ..................................................................................................................... 43
7.2 HTML Screens ........................................................................................................................... 44
7.3 HTML Listing Extract................................................................................................................. 45
8 Electrical Drawings................................................................................................................................ 49
9 Key Spare Part Numbers ....................................................................................................................... 52

3
10 Technical Data........................................................................................................................................ 52
11 Version .................................................................................................................................................... 53
Disclaimer
This documentation has been provided by FANUC Europe Corporation S.A. (“FANUC”) for
convenience and general information purposes only, with no intention of providing comprehensive,
complete, accurate or up to date information. Therefore, FANUC does not warrant or assume any
legal liability or responsibility whatsoever for the accuracy, completeness, or usefulness of any
information, application, apparatus, product, use, processes or services disclosed herein.
Should you be interested in obtaining specific information or advice on FANUC applications,
apparatus, products, use, processes or services, please contact FANUC at:
FANUC Europe Corporation
Société Anonyme
Zone Industrielle
L-6468 Echternach
Grand Duchy of Luxembourg
Tel.: +352-727777-1
INTENDED USE OF EDUCATION CELL
The Education Cell is intended for Education and Training Purposes
It is designed for lightness and portability,
not for high speed robot motion or full acceleration.
If robot is programmed to move aggressively
then this may result in undesirable shaking of the frame,
even resulting in the activation of the door safety switch.
Please avoid such unintended use.

4
1 Selecting and running Example program
1.1 Start Up Screen
When the robot controller is turned on, it displays the following Start-Up Instructions:

5
1.2 Example Program “AAA_DEMO”
The program “AAA_DEMO” has been provided as an example program.
It transfers the cylindrical parts supplied from one triangular ‘solitaire’ board to another.
To start the program follow these steps:
a. Robot must be in ‘AUTO’ mode, all E-Stops released, and cell door (‘Fence’) closed
b. Robot should not be in error condition. If robot shows error condition press the “RESET” key
on the Teach pendant to try to reset the errors.
c. Select the program “AAA_DEMO” and Press the ‘Cycle Start’ button on the front of the
controller.
(Teach pendant enable switch must be OFF and Auto/T1/T2 switch must be in ‘Auto’ position)
Please note – program “AAA_DEMO” must be selected before pressing ‘Cycle Start”

6
d. The program AAA_DEMO expects to be started from the HOME position:
Robot at HOME Robot not at HOME
If the Robot is not at the HOME position, the following screen will appear:
Choose the appropriate action and press
‘ENTER’
If Option 2 “ Continue “ is chosen, then a confirmation screen will be displayed:
Note that these two functions have been
implemented using the ‘Menu Utility’
function – see later section for details.

7
e. Before the program starts, a screen will ask for confirmation that the parts are in the
correct starting position:
Make sure that the parts are in the
positions shown, then press “Continue”.
f. When the program is running, a Status / Menu screen is shown:.
The red/white circles show the current
position of the pieces
There are two function Key Selections: End
Cycle / Continue and Fast/Slow.
If ‘End Cycle’ is pressed, this changes
Register R[1] from 1 to 0, and the Cycle
Stop status changes from Inactive to Active:
This will mean that the program will stop at
the end of the next complete cycle and the
Program Status will then become ‘Ended’

8
g. Likewise, the Fast/Slow Function key changes the Override:
Note: the Fast / Slow Override speeds are set according to the values in R[4] and R[5] – see
later section for details
And the F4 function Key enables / disables
the Vision Load / Unload section of the
program – see next section for details.
Note: iRVision must be installed and set up
for this function to be used.

9
1.3 AAA_DEMO Program Sequence with / without iRVision
There are 3 basic positions for the parts in/on the Solitaire board:
In the Left Hand side of the board:
This is the start and end position of the example
program
In the Right Hand side of the board:
On the middle of the board:
This position is only used if iRVision is enabled for
the example program using “F4” function key
If Vision L/UL is Disabled then
sequence is:
 Move Parts from Left Hand side to
Right Hand side
 Move Parts from Right Hand side
to Left Hand side
 Repeat
If Vision L/UL is Enabled then
sequence is:
 Move Parts from Left Hand side to
Right Hand side
 Move Parts into middle of board
 Move Parts from middle of board
to Left Hand side using iRVision.
 Repeat

10
1.4 Operation Menu Display
The Operation Menu can be displayed at any time by pressing the MENU key and then
selecting the “Operate” shortcut that pops up:

11
1.5 4D Graphics (Option)
The “4D Graphics” function is available as an option, with a model of the cell loaded into the robot
controller.
This model can be displayed by pressing the MENU button and selecting “4D Graphics”:
The 4D graphics function has many features, for example as shown below the display of the Jog
Coordinates – in this case the WORLD Jog Coordinate System:

12
2 Demonstration Program Setup / Teaching
The positions of the holes in the tray are calculated, not taught – so there should be no need to
touchup / reteach the individual hole positions. However, it may be necessary to touchup / reteach
the User Frame (UFrame) which defines the position of the tray relative to the robot.
2.1 Gripper Setup
To teach the positions it is necessary to use a part held in the gripper.
Gripper Force should be set at 50% using the small rotary switch on the gripper.

13
2.2 UFrame 2 Setup
The User Frame touchup is done using the Menu>Setup>Frames function:
This requires 3 Points to be touched-up / re-taught:
Note that the MOVE_TO function key provides a
method to easily check the current taught
positions

14
First, insert a piece into the gripper:
Make sure gripper is vertical, and jog the robot so that the piece is central in the Left-most hole on
the tray shown below:

15
It is difficult to know when the piece is touching the table at the bottom of the hole – so this
position is not used for the reference point.
Instead, jog the robot upwards using WORLD+Z until the bottom of the piece is just above the top of
the tray. Use a thin piece of card to help judge this correctly:
2.3 Orient Origin Point
Then RECORD this position as Orient Origin Point – see below:

16
2.4 X-Direction Point
Now do the same thing for the Right-most hole in the tray:
And RECORD this position as X-Direction Point – see below:

17
2.5 Y-Direction Point
And finally any position on the top surface of the front of the tray:
And RECORD this position as Y-Direction Point – see below:
Note – Y-Direction Point defines the X-Y plane, so any position in the right plane will do.
This procedure will touch-up / re-teach the UFrame #2

18
3 Robot Setup
3.1 UTOOL / TCP Setup
Because of the simple shape and mounting of the Schunk gripper, a simple TCP with an offset of
115mm in Z is sufficient.
3.2 Payload Setup
The payload is quite low for this application – so only one payload of 0.5 kg has been set:

19
3.3 DCS Setup
DCS (Dual Check Safety) has been used to ensure that the robot cannot accidentally hit the walls of
the cell. This requires setting up a Tool Model and a Safe Zone.
3.3.1 DCS Tool Model.
A simple DCS model using one “Line_seg” type model has been used.
For more details please refer to DCS manuals.

20
3.3.2 DCS Safe Zone
A simple DCS Cartesian Position Check Zone has been set up using a Diagonal line to define a
cuboid zone, running from a point on the “ top left “ of the cell to the “bottom right “ – see
screenshot below - where the inside of the cuboid is safe.
If the robot or the tool comes close to the edge of this zone, the robot will stop.
For more details please refer to DCS manuals.

21
3.4 I/O Setup
Only 2 I/Os are used, for gripper Open / Close
These outputs are configured as Complementary, so when, for example RO[7] is set ON, RO[8] is
automatically forced to OFF and vice-versa.

22
3.5 Macro Setup
One macro has been set up, to allow the user to easily toggle the gripper open / close using SHIFT
+ User Key 1 on the Teach Pendant:

23
3.6 TP Function Key Hint Screen
To allow the user to easily remember the setting of the Function Key, a Hint Screen has been set
up using an HTML Page:
When the “Menu” key is pressed, the Shortcut key F2 “FKey” pops up:
Pressing F2 will display the FKey Hint
screen:
This screen shows the current
assignment of the function keys.
The text which is displayed is the text
stored in String Registers SR[21] –
SR[25]

24
3.7 Home / Reference Position
One reference position has been set up, which is used for the HOME position check. Home position
is this:
And setup is this:
When the robot is in this position, the output DO [101] will be ON – and this can be checked by the
TP program AA_CHK

25
3.8 Power Up Program
To provide instructions to the user, a Power-Up program “PWR_UP.TP” has been assigned to both
Hot Start and Cold Start.
The program simply writes instructions to the Teach Pendant:

26
4 iRVision Setup ( Option )
The Education Cell is available with and without integrated iRVision using Sony XC56 video camera.
In either case, the iRVision Setup has not been done on the Education Cell controller. Please
contact your local FANUC representative to arrange training on iRVision
The following section is just to give a short overview of a sample iRVision setup, and is not intended
to take the place of a proper iRVision training.
4.1 Camera Adjustment
If this option has been ordered, the basic camera setup should already have been done by FANUC
Europe, so the camera should display an image something like this:

27
If the Camera View is not like this, then please adjust using the screws on the Camera Mounting
bracket:

28
4.2 Application Frame
It is good practice to set up an Application Frame to use with iRVision, for example Uframe 9.
This can be done in the same way as shown in section 2:
Orient Origin Point:
X-Direction Point:
Y- Direction Point:

29
4.3 Camera Calibration
The iRVision Calibration Grids are not included in the Education Cell. Instead the “Robot Generated
Grid Calibration” Method can be used – please refer to the iRVision Operation Manual for details.
Basically a target should be temporarily attached to the Gripper as shown:
(The design of the target is explained in the iRVision manual – it should be approx. 50mm
diameter)
It will appear something like this in the camera field-of-view:

30
The Camera Calibration takes place in 2 steps:
 First find the relationship of the target to the robot
 Second move the target around the field of view to calibrate the camera
Please note that it may be necessary to disable DCS while calibrating the camera field of view
since the robot moves the target right to the edges of the field of view, close to the side walls.
All of this is done through the Teach Pendant using the iRVision Utilities Menu:
For details please refer to the iRVision Operation Manual. Note that for the Start Position, there
must be enough space between the robot wrist and the cell – approx. 70mm is good:

31
4.4 Example iRVision Application
A simple application could be to load the parts from the centre of the board into the starting
position for the Solitaire program
So the parts start like this, And end like this,
randomly placed in the centre of the board in the start position for ‘Solitaire’
Using FANUC iRVision this is quite straightforward to do:
 Calibrate the Camera (as shown previously)
 Teach a reference pick-up position for one of the parts
 Teach iRVision to recognise and locate one of the parts.
 Create a TP program to use the iRVision information to pick the part and then place into
the board.
(This was suggestion but has been now added to the demo cell as shipped by FANUC – see
section 1.3)

32
4.5 iRVision Tips
FEC set this application up using the Vision Process below:
 A simple GPM locator tool to find the cylindrical part
 The GPM Locator has a run-time mask to restrict the vision to the centre of the board to
avoid finding the ‘holes’ instead of the parts:

33
 Then the Histogram Tool and the Conditional Execution Tool are used to make sure that
there is enough free space around the part to allow it to be picked up.
So all of these parts can be picked: But the two central parts here cannot be
picked because they are too close together.

34
4.6 TP Program
Write a simple TP program to Pick and Place the parts:
It is advisable also to add in some simple error handling to check that the Vision is working OK.
This can be done using the Menu Utility as described in section 7
For more details please refer to the iRVision Operation Manual or arrange training with your local
FANUC Europe representative.

35
5 List of Registers
5.1 Numeric registers
Registers are used to store settings to control the cell operation, and used by the program internally.
Register Comment Description Default value
1 Continue Cycle This register is set to 1 at start of
“AAA_DEMO”. If value is 1 then the
program will loop continuously.
If value is 0, program will stop at end of
next full cycle.
Value can be set manually or by the
Menu screen described in earlier
section.
1 to loop
0 to end
2 In Cycle This register is set to 1 at start of
“AAA_DEMO”, and is set to 0 at end of
program
1 when in cycle
0 at end of cycle
3 Speed Mode This register is set via the Menu screen
described earlier.
1 is fast mode,
anything else
slow.
4 Fast OVRD This is value that will be used for
Override in Fast Mode
75%
5 Slow OVRD This is value that will be used for
Override in Slow Mode
50%
6 User Input Used by the Menu Utility to return the
User’s Choice of actions
1
7 Vision Installed This should be set during software
installation / setup.
1 is installed,
anything else not
installed
8 Vision Enabled This is set by the Operation Menu to
enable / disable Vision L/UL. Both R[7]
and R[8] must be 1 for the vision section
of the example program to run
1 is enabled,
anything else not
enabled
10
11
12
SPEED1
SPEED2
ACC
These are speeds and acceleration
used for moves. They are set low to
avoid frame shaking when on wheels.
(If frame is fixed more securely, speed
and acceleration could be increased)
750mm/sec
750mm/sec
75%

36
Register Comment Description Default value
13 CURR PIN This value is used internally by the
program to keep track of the part
number
n/a
16 IRV COUNT Used to load 9 parts with Vision n/a
100
101
102
103
ID_PICK_CYLINDER
ID_PLACE_HOLE
ID_REMOVE_CYLIND
ID_EMPTY_PLATE
These values are used internally by the
program to control the sequence of
moves
n/a
105 Tmp_cyl_reg This value is used internally by the
program to set the status registers
below
n/a
111
to
130
A1 in
to
-D4 in
These registers are used to store the
status of the parts and holes.
The values in these registers are linked
to the Menu Displays using the iPendant
Controls – see later section
1 = occupied
0 = unoccupied

37
5.2 Position Registers
Position Registers are used to store positions
Position
Register
Comment Description
11
to
30
A1
to
-D4
Locations of the holes in the tray.
Note that these are calculated values, not taught values.
PR[11] was taught, then the other PR[]s were calculated relative
to it.
31
to
39
Mid 1
to
Mid 9
‘Random’ positions in middle of board – not in holes – robot will
find actual position using iRVision
40
41
ToolOff
ToolOff1
These are Tool Offsets, used to create the motion above / to the
pick and place locations.
The Registers can be displayed using the ‘Data’ button on the Teach Pendant:

38
6 Program Details
6.1 List of programs
The following programs are installed in the Education Cell:
Program Comment Description
AAA_DEMO Example program This is Main Example program – it must be
selected before pressing ‘Cycle Start’
AA_CHK Check Start OK Program to check robot at home and parts in
correct position.
Uses Menu Utility to display choices and
confirmation to user – see later section for details.
Also uses .STM file to display graphic of correct
part position – see later section for details.
AA_HOME Move Home This program moves the robot to the home
position. Note that it uses Joint definition position –
so independent of any UFrame or UTool settings
AA-OVRD Set OVRD Fst Slo Set override to value specified in R[4], R[5]
depending on value of mode R[3]
ABORTIT ABORT PRODUCTION Predefined system program – not used by this
application
DSP_WEBP Display Web Page Macro installed by the ‘Menu Utility’ Option.
This macro is used to display the Menu Screens.
GETDATA Get PC Data Predefined system program – not used by this
application
HAND_CLOSE Close Gripper Program to Close Schunk Gripper ( Note 1)
HAND_OPEN Open Gripper Program to Open Schunk Gripper ( Note 1)
HAND_TOG Toggle Gripper Program to toggle gripper between Open and
Close.
This program is linked to the User Key 1 on the
Teach Pendant – see details in later section
IRV_LOAD Get Parts Vision Pick parts from centre of board using vision and
place in left hand side of board
IRV_PICK Get 1 Part Pick 1 part from centre of board using vision and
place in left hand side of board – called from
IRV_LOAD

39
Program Comment Description
IRV_RAND Put Parts Vision Pick parts from Right hand side of board and place
in semi-random positions on middle of board for
robot to find using iRVision
IRV_SET IRV Setup Posn Program containing suitable start position for
iRVision Camera Calibration
LISTMENU LIST MENU MACRO Macro installed by the ‘Menu Utility’ Option.
This macro is used to display 3 choices to the user
when the robot is not at HOME
OPERMENU Entry Menu Macro Macro installed by the ‘Menu Utility’ Option.
This macro is not used in this application
PROMPTOK Prompt Box OK Macro installed by the ‘Menu Utility’ Option.
This macro is not used in this application
PROMPTYN Prompt Box Y N Macro installed by the ‘Menu Utility’ Option.
This macro is used to confirm the choice by the
user when the robot is not at HOME
REQMENU
SENDDATA
SENDEVNT
SENDSYSV
STATPAGE
Request PC Menu
Send PC Data
Send PC Event
Send PC Sysvar
StatusMenu Macro
Predefined system programs – not used by this
application
S_SET1_PR Solit Setup 1PR Set coordinates of one Position Register for one
hole
S_SETUP_PRS Solit Setup PRs Set coordinates of all Position Register for all holes
S_SOLIT_RESET Reset Status Rs Reset registers showing part status to start
conditions
S_UNLD1 Solit Unload 1 Make one move, jumping over a piece and then
moving the jumped-over piece to the other half of
the board.
S_UNLDALL_L Solit Unl All L Sequence for the left side of the board, moving
pieces to the right side
S_UNLDALL_R Solit Unl All R Sequence for the right side of the board, moving
pieces to the right side
S_UNLDLST Solit Unld Last Make one move – for first or last pieces
USERCLEAR
USERPAGE
Clear User Page
Show User Page
Macros installed by the ‘Menu Utility’ Option.
These macros are not used in this application
ZERO Move to Zero Move all axes to zero

40
Note 1) In order for the Roboguide Simulation to work correctly picking and placing the virtual parts,
the HAND_CLOSE and HAND_OPEN .TP programs must be replaced with Simulation programs.
Please refer to actual Roboguide cell for details

41
6.2 Sample Program Listings
This is listing of main program “AAA_DEMO”:
/PROG AAA_DEMO
1: !FANUC EUROPE EDUCATION CELL ; << Remark
2: !Example Solitaire Program ; << Remark
3: !with optional vision ;
4: CALL AA_CHK ; << Call program to check Start OK
5: R[1:Continue Cycle]=1 ; << Set Register to run continuously
6: R[2:In Cycle]=1 ; << Set Register to show status
7: CALL AA_OVRD ; << Call program to set Override %
8: CALL HAND_OPEN ; << Make sure gripper is open
9: LBL[1] ; << Label to loop up to if needed
10: CALL S_SOLIT_RESET ; << Reset status registers
11: CALL S_UNLDALL_L ; << Sequence to move pieces from Left to Right side of board
12: WAIT 2.00(sec) ; << Short delay
13: IF R[7:Vision Installed]<>1,JMP LBL[2] ; << Check if use Vision or not
14: IF R[8:Vision Enabled]<>1,JMP LBL[2] ; << Check if use Vision or not
15: CALL IRV_RAND ; << Move parts from Right of board to Middle
17: CALL IRV_LOAD ; << Pick parts from Middle of board using Vision and put in Left Side
19: JMP LBL[3] ; << Jump over next section
20: LBL[2] ; << Label for Jump
21: CALL S_UNLDALL_R ; << Sequence to move pieces from Right to Left side of board
22: LBL[3] ; << Label for Jump
24: IF R[1:Continue Cycle]=1,JMP LBL[1] ; << Repeat if register 1 is equal to 1
25: R[2:In Cycle]=0 ; << Set register to show status at end of program
/POS
/END /END

42
This is listing of program “AA_CHK”:
/PROG AA_CHK
1: !Check Start Conditions OK ; << Remark
2: ;
3: !Check at HOME ; << Remark
4: IF DO[101:HOME Signal]=ON,JMP LBL[10] ; << Check HOME signal – see later section for detail
5: LBL[1] ;
6: R[6:User Input]=0 ;
7: CALL LISTMENU(2,6) ; << Call Menu Utility to display User Menu 2, result in R[6]
8: SELECT R[6:User Input]=1,JMP LBL[3] ;
9: =2,JMP LBL[5] ;
10: ELSE,JMP LBL[2] ;
11: LBL[2] ;
12: ABORT ;
13: JMP LBL[10] ;
14: LBL[3] ;
15: CALL AA_HOME ;
16: JMP LBL[10] ;
17: LBL[5] ;
19: CALL PROMPTYN(2,6) ; << Call Menu Utility to display Prompt Box 2, result in R[6]
20: IF R[6:User Input]=1,JMP LBL[10] ;
21: JMP LBL[1] ;
22: LBL[10] ;
23: ;
24: !Check parts OK ;
25: CALL S_SOLIT_RESET ;
27: !Display Check Page ;
28: CALL DSP_WEBP(3) ; << Call Menu Utility to display User Status / Confirmation Menu
29: WAIT R[6:User Input]<>0 ;
30: IF R[6:User Input]=1,JMP LBL[20] ;
31: ABORT ;
32: LBL[20] ;
33: !Display Run Page ;
34: CALL DSP_WEBP(4) ; << Call Menu Utility to display User Status / Operation Menu
/END

43
7 User Interface Setup
7.1 Menu Utility Setup
The User Menu and Prompt at the start of the AA_CHK program have been set up using the Menu
Utility. See below for screenshots.
Once these menus have been set up, they can be called using the predefined macros “LISTMENU”
and “PROMPTYN”

44
7.2 HTML Screens
The Status / Menu Screens were created using MS Sharepoint Designer 2007:
Then the files were loaded into the controller and added to the browser favourites menu:
So that they can be displayed manually or using the CALL DSP_WEBP(3)program, which is included in
the Menu Utility

45
7.3 HTML Listing Extract
This is extract of listing for “EdCellOp.stm”
<head> Title of the Page
<meta http-equiv="Content-Language" content="en-gb">
<meta http-equiv="Content-Type" content="text/html; charset=utf-8">
<title>Education Cell Menu</title>
<style type="text/css">
.style1 {
border-color: #FFFFFF;
border-width: 0;
background-color: #333333;
}
.style2 {
text-align: center;
}
</style>
</head>
<body>
<div class="style2">
<table style="width: 41%"> Table with two columns, left column for board layout, right column for
status boxes
<tr>
<td style="width: 235px">
<table style="width: 140px; height: 180px; float: right;" class="style1">
<tr> Table with 7 columns and 9 rows to show board positions
<td></td>
<td></td>
<td></td>

46
<td style="width: 30px"> Definition of one board position
<object classid="clsid:71060668-0E45-11D3-81B6-0000E206D650" id="Sol1"
style="width: 20px; height: 20px">
<param name="Caption" value="">
<param name="FontSize" value="14">
<param name="width" value="20">
<param name="height" value="20">
<param name="DataType" value="101"> State linked to Register
<param name="DataIndex" value="121"> Register number 121
<param name="TrueColor" value="255"> True Colour = Red
<param name="FalseColor" value="16777215"> False colour = Light grey
<param name="Interval" value="250">
<param name="TrueFont" value="-1">
<param name="FastLoad" value="-1">
<param name="Border" value="1">
<param name="ViewType" value="1">
</object>
</td>
<td></td>
<td></td>
<td style="width: 49px"></td>
</tr>
Repeat for all other board positions up to 20
</table> Set up objects in right column
</td> Add label
<td class="style2">
<object classid="clsid:7106065C-0E45-11D3-81B6-0000E206D650" id="FRIPLabel1"
style="height: 30px; width: 150px">
<param name="Caption" value="Program Status">

47
<param name="DataType" value="100">
<param name="DataIndex" value="">
</div>
</object>
<br> Add Lamp Object to show status of program
<object classid="clsid:71060668-0E45-11D3-81B6-0000E206D650"
id="FRIPToggleLamp4" style="height: 40px">
<param name="Caption" value="Ended"> Set text for False
<param name="DataType" value="101"> Link to Register
<param name="DataIndex" value="2"> Register 2
<param name="TrueColor" value="255">
<param name="FalseColor" value="65280">
<param name="TrueCaption" value="In Cycle"> Set Text for True
</div>
</object>
<br>
Repeat for other lamps
</table>

48
Add TP Key labels / functions objects
<object classid="clsid:7106066C-0E45-11D3-81B6-0000E206D650" id="EndCycle" tabindex="-1">
<param name="Caption" value="Continue">
<param name="DataType" value="101"> Sets Register
<param name="DataIndex" value="1"> Register 1
<param name="TrueColor" value="65280">
<param name="FalseColor" value="255">
<param name="ViewType" value="3">
<param name="BackColor" value="8454016">
<param name="TrueCaption" value="End Cycle">
</object>
Repeat for other Key
</p>
<p> </p>
</div>
</body>
</html>

52
9 Key Spare Part Numbers
Item Description Manufacturer Part Number
1 Gripper Schunk EGP-40
2 Safety Switch
Actuator / Key
Omron
Omron
D4NS-4DF
D4DS-K3
3 Spare Parts Box RS Components 303-4755
10 Technical Data
Technical
data:
Power rating 230V 16A single phase
Power
consumption
1 KW/h
Connection Schuko plug (German style)
Air supply None
Air consumption None
Installation size Base 1,3 x 0,7 m Height 1,8m
Weight 170kg
Transport data
Size Base 1,3 x 0,7 m Height 1,8m
Weight 170kg
Packing Bubble foil
Handling Delivered on Pallet – When removed from pallet on wheels

53
11 Version
Document title: FEC Education Cell Technical Documentation – Plus Controller
V4.1 Conversion from R-30iB to R-30iB Plus, with new Kowa Camera
V4.2 TP Menu Function Key Icons updated
V4.3 Wiring Diagrams and spare parts numbers added
Version: V4.3 20-11-2018 N. Ramsden

Fanuc educational cell manual

More Related Content

What's hot (20)

Similar to Fanuc educational cell manual (20)

Recently uploaded (20)

Fanuc educational cell manual