Identification of isomorphism and detection of distinct mechanism of kinematic chains using invarient labeling of links

IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
__________________________________________________________________________________________
Volume: 03 Issue: 01 | Jan-2014, Available @ http://www.ijret.org 17
IDENTIFICATION OF ISOMORPHISM AND DETECTION OF DISTINCT
MECHANISM OF KINEMATIC CHAINS USING INVARIENT LABELING
OF LINKS
S.R.Madan
Professor, Mechanical Engineering Department, Mahakal Institute of Technology and Management, UJJAIN,
(M.P), INDIA
Abstract
The problem of isomorphism among kinematic chains and of these derived mechanisms has been a hot area of research being done
from last several years. The researchers so far have proposed many methods which are mainly based on characteristic polynomial
and on some code based method to test the isomorphism among kinematic chains. In the present communication a new structural
invariant based on link-link path distance (shortest) has been developed for a kinematic chain. Each link of kinematic chain is
assigned as a unique label using the invariant. The set of link labels are combined in the form a numerical label of kinematic chain,
called kinematic chain label (KCL). KCL is proposed as unique identifier for detection of isomorphism among kinematic chains, and
also used to find distinct mechanism of a kinematic chain. Method is tested on several cases of single degree of freedom plannar
kinematic chain successfully with simple joints.
Keywords: - Isomorphism, Kinematic chains, Mechanism, Invarient labeling, Distinct mechanism, path distance matrix.
---------------------------------------------------------------------***---------------------------------------------------------------------
1. INTRODUCTION
Structural analysis and synthesis of kinematic chains is tried to
be carried out as an important aspect of mechanism design. In
the early stage of mechanism design, it is helpful to determine
all the distinct kinematic chains with the required number of
links and degree of freedom. One very important problem
encountered during structural synthesis of chains and the
detection of possible isomorphism among the given chains.
Several attempt(1-18)
were made to develop reliable and
computationally efficient algorithms for automated test of
isomorphism but each has its own shortcomings. Duplicate or
isomorphic chain leads to redundant computation. In order to
achieve greater efficient in computer aided mechanism design
research for simple, reliable and effective methods is of great
significance.
Several methods were proposed by researchers to test
isomorphism among kinematic chains. Characteristic
polynomial of adjacency matrix was proposed by Uicker and
Raicu(1)
for the time as a numerical measure of kinematic
chain structure. Later it was found during the synthesis of
kinematic chains by Mruthyunjaya(2)
that it was only a
necessary condition and nonisomorphic chains having
identical characteristic polynomial were detected.
Characteristic polynomial of vertex – vertex degree matrix
was proposed in (3) by Mruthunjaya and Balasubramanian.
Discovery of counter examples led to the development of new
indices characteristic polynomial of distance matrix was
proposed by Dubey and Rao(4)
. Caninical formation of upper
triangular adjacency matrix of kinematic chain by relabeling
of links was used to generate Max and Min code by Ambekar
and Agrawal(5,6)
.
An altogether different approach was made by Rao and co-
workers and several indices based on Hamming number was
proposed by them (7-10)
.
Link’s adjacent table (ACT) and complete adjacent table
(CACT) obtained by successive replacement of link labels
wise in a systematic manner so as to produce a unique string
was proposed as a method to detect isomorphism by Chu and
Cao(11)
.
Ding and Huang proposed methods based on Canonical
perimeter topological graph(12)
and characteristic adjacency
matrix(13)
.
Approaches based on artificial neural network, genetic
algorithm and novel evolutionary approaches were also
proposed by some researchers(14-16)
.
Most of the methods reported so far require comlex algorithms
to carry out the test. A broad review of the methods published
was given Mruthyunjaya in (17)
and it was concluded that quest
for computastionally efficient, reliable and simple methods is
still on. Bearing the above in mind, a methodology based on
link-link distances and degree of links of kinematic chain,

__________________________________________________________________________________________
invariant link labels and entropy of chains are proposed to
detect isomorphism, best chain of plannar kinematic chains
with their distinct mechanisms.
2. ARCHITECT OF THE PROPOSED METHOD
2.1 Degree of link d(li)
The degree of a link actually represents the type of the link,
such as binary, ternary, quaternary links etc. Let the degree of
ith
link in a kinematic chain be designated d(Li) and d(Li) = 2,
for binary link, d(Li) = 3, for ternary link, d(Li) = 4, for
quaternary link and d(li) = n, for n-nary link.
2.2 Labeling of link (Vi)
Usually, the canonical labels depend only on the connectivity
of the links being labeled together with its immediate
neighbours. However, in a closed kinematic chain, links are
connected by joints so as to form loops and every link has a
distinct relation with every other link in the form of distance
between them which is constant and presented here by a
matrix is called link path matrix of the chain. Bearing this in
mind the usual canonical labeling is extended to include all
links of the chain. Canonical label V of a link of a kinematic
chain, defined here, is a sum of path weighted connectivity of
the links. Each link L is assigned a label Vi as follows –
-----------------(1)
Where Wj is the weight of degree of jth link with related to
total degree of kinematic chain . And Wj is related weight of
degree of the links which is defined as the ratio between of jth
link and total degree of kinematic chain given as
Wj =d(Li) / d(KC) (2)
To include all links but give a higher path weight to those
closest to the link Li being labeled, a factor of ( ½ Dij
) is
included where, Dij is the distance between the links Li and Lj.
This distance is defined as the shortest path between any two
links of a chain. N is the total number of links in the chain
being labeled.
Consider for example, six – link; single degree of freedom
Watt and Stephenson chain shown in Figs., 1(a) and 1(b),
respectively. Invariant link labels are calculated as-
For Watt chain shown in Fig. 1(a), relative weight of 6 links
using eq. 2 are
Fig. 1(a) Watt chain Fig. 1(b) Stephenson chain
1 2 3 4 5 6
0.21428 0.14285 0.14285 0.21428 0.14285 0.14285
And link-link path matrix is
Link 1 2 3 4 5 6
1 0 1 2 1 2 1
2 1 0 1 2 3 2
3 2 1 0 1 2 3
4 1 2 1 0 1 2
5 2 3 2 1 0 1
6 1 2 3 2 1 0

__________________________________________________________________________________________
Invarient label for any link is sum of path weight connectivity
of all the links. Thus the
----------------(3)
Thus invariant label V1 for link 1 of Fig. 1(a)
= 1/20
● 0.21428 + 1/21
● 0.14285 + 1/22
● 0.14285 + 1/21
●
0.21428+ 1/22
● 0.14285 + 1/21
● 0.14285 .
= 0.5356
Similarly for all the other links, labels can be calculated as
shown below.
V2 = 0.4285, V3 = 0.4285 , V4 = 0.5356, V5= 0.4285, V6 =
0.4285
So for Watt chain the labels are
[ 0.5356, 0.4285, 0.4285, 0.5356, 0.4285, 0.4285 ]
And Squared sum of links labels, defined as kinematic chain
label(KCL)
---------------------------(4)
and KCLwatt is 1.3085
For Stephenson chain shown in Fig.1(b), the labels are
[0.5178, 0.4642, 0.5178, 0.4642, 0.4464, 0.4464] and KCL is
1.36564
2.3 DETECTION OF ISOMORPHISM
The set of link labels can be directly be used to distinguish
kinematic chains. To make it more meaningful the labels
calculated above can be combined to generate a numerical
code for a kinematic chain. Squared sum of links, defined as
kinematic chain label (KCL) is proposed as an index for
testing isomorphism. Two chains having identical KCL will be
isomorphic to each other.
Application of the Concept is Illustrated with the
help of Several Examples.
Example 1. Watt and Stephenson chain are shown in Fig. 1 (a)
and in Fig. 1(b) respectively. Link labels calculated using
equation (1), and (2) for Watt chain is [ 0.5356, 0.4285,
0.4285, 0.5356, 0.4285, 0.4285] and KCL calculated by
equation (3) is equal to 1.3085 and by the comparison of
labels of links of kinematic chain (Watt chain) it is found that
there two distinct mechanism will be obtained i.e for links
(1,4) and for links (2, 3, 5, 6 ) .
For Stephenson chain the labels are
[0.5178, 0.4642, 0.5178, 0.4642, 0.4464, 0.4464] and KCL is
1.365964.
By the comparison of KCL of Watt chain and Stephenson
chain it is clear from the result that two chains are distinct.
Example 2 – Consider the two chains shown in Fig.2.
(a) (b)
Fig. 2 Eight link isomorphic chains

__________________________________________________________________________________________
For Fig.2(a), the labels are
[0.4625, 0.375, 0.4625, 0.4375, 0.450, 0.3875, 0.3625, 0.3562]
and KCL is 1.370820
For Fig.2(b), the labels are
[0.375, 0.4375, 0.3875, 0.45, 0.4625, 0.4625, 0.3625, 0.3562]
and KCL is 1.370820
The labels and corresponding chain labels for both the figures
are identical hence the chains are isomorphic.
Example 3- Consider the two chains shown in Fig.3.
Figure 3(a) Figure 3(b)
Nine links two degree of freedom kinematic chains
For Fig.3(a), the labels and KCL are
[0.4317, 0.4317, 0.4033, 0.3522, 0.4147, 0.3352, 0.3408,
0.3352, 0.3352] and KCL= 1.2850
For Fig.3(b), the labels and KCL are
[0.40907, 0.40607, 0.3295, 0.3295, 0.3352, 0.3352, 0.4204,
0.4545, 0.3465] and KCL is 1.20004
The chain label and KCL for Nine link two degree of freedom
chain shown in Fig. 3(a) and Fig. 3(b) are non identical, so it
is clear from result that two chains are non-isomorphic.
Example 3- Three 12-bars non-isomorphic kinematic chains
cited from (12)
are shown in Figs.3(a), 3(b) and 3(c)
respectively. They have identical characteristic polynomial.
The link labels and corresponding chain labels for the figures
are:
(a) (b)
( c )
Fig 4 Twelve-link 1-dof kinematic chains

__________________________________________________________________________________________
Fig.4(a)
Link Labels: [ 0.2832, 0.2832, 0.2871, 0.2792, 0.3476,
0.3554, 0.3554, 0.3476, 0.3554, 0.3027, 0.3554, 0.3417].
KCL = 1.2764
Fig. 4( c)
Link Labels : [ 0.3476, 0.3554, 0.3554, 0.3476, 0.3554,
0.3417, 0.3554, 0.3027, 0.2832, 0.2832, 0.2792, 0.2871].
KCL = 1.2764
Fig. 4(b)
Link Labels : [ 0.2832, 0.2832, 0.2929, 0.2617, 0.3261,
0.3359, 0.3671, 0.3554, 0.3027, 0.33007, 0.3359, 0.3359].
KCL = 1.22147
Chain shown in Fig. 4(a) and 4(b) are isomorphic to each
other, only links are relabeled in a different manner. Result
clearly show that the invariant is independent of relabeling of
links. KCL for Fig 4 is different hence it clearly reflects that
the chains are uniquely identified by KCL.
Example 4 , Complete set of 8 links, 1-degree of freedom
kinematic chains is shown in Fig.5. The kinematic chain is
calculated for each chain and is shown in Table 1. All of these
chains have distinct value of KCL. The notation for each
family title is given; ( number of ) quaternaries, ternaries and
binaries. Thus 206 stand for two quaternaries, zero ternaries
and six binaries.
Table 1 – Kinematic chain labels and DM of Six and Eight – link single degree – of – freedom kinematic chains.
Fig 5. Complete set of eight –links 1 degree of freedom kinematic chains
K.Chain Chain Family KCL Distinc Mechanism
No.
Six link single degree of freedom kinematic chain
Watt chain 024 1.3085 (1,4), (2,3,5,6) = 2
Stephenson chain 024 1.365964 (1,3), (2,4), (5,6) = 3
Eight link single degree of freedom kinematic chains
1. 044 1.265625 (2,3,6,7), (1,4,5,8) = 2
2. 044 1.35875 (1,2,5,6), (3,4,7,8) = 2
3. 044 1.37082 1, 2, 3, (4,50, 6, 7, 8 = 7
4. 044 1.314844 (1,5), (2,4), 3, (6,7),8 = 5
5. 044 1.312031 (1,4) (2,8), (3,7), (5,6) = 4
6. 125 1.338750 1, (2,6,7,8), (3,5),4 = 4
7. 125 1.371016 1, 2, 3, 4, 5, 6, (7,8) = 7
8. 125 1.379727 1, 2, 3, 4, 5, 6, 7, 8 = 8
9. 044 1.328203 (1,8), (2,7), (3,6), (4,5) = 4
10. 044 1.410625 (1,3,4,7), (2,5,6,8) = 2
11. 044 1.218672 1, 2, 3, 4, 5, (6,7), 8 = 7
12. 044 1.255781 (1,2,4,5),(3,6,7,8) = 2
13. 125 1.410820 1, (2,8), 3, 4, 5, 6, 7, 8 = 7
14. 125 1.330313 1, (2,5,8), (3,7), (4,6) = 4
15. 206 1.3950 (1,4), (2,3,5,6,7,8) = 2
16. 206 1.49875 (1,4), (2,5,6), 3, (7,8) = 4
-------------------------------
Total D.M = 71

__________________________________________________________________________________________
3. RESULT AND CONCLUSIONS
In this paper a heuristic method for detection of isomorphism
among kinematic chains is presented. The proposed method is
also tested to obtain all DM derived from a family of
kinematic chain. Method is simple, reliable and can easily be
implemented on computer. A program is written in C++
and
entire calculations was carried out in a personal computer with
Pentium duel core ES200 @2.5 GH2 with 1 GB random access
memory. With the help of present method kinematic chains
can be checked with single numerical invariant. Also DM of a
kinematic chain are derived from the family of 1 DOF 6 and 8
links in accordance with the result given by Vijayanath(18)
and
Yadav(19)
and is shown by table no-1.
REFERENCES
[1] J.J.Uicker and Raicu, “A Method for the
Identification of Recognition of Equivalence of
Kinematic Chains” Mechanism and Machine Theory,
vol.10, pp. 375-383, 1975.
[2] T.S.Mruthyunjaya, “A Computerized Methodology
for Structural Synthesis of Kinematic Chains – Part I,
II, III,” Mechanism and Machine Theory, vol. 14, pp.
487-530,1984.
[3] T.S.Mruthyunjaya and H.R.Balasubramanian, “In
Quest of reliable and Efficient Computational Test for
Detection of Isomorphism in Kinematic Chains,”
Mechanism and Machine Theory, vol. 22, pp. 131-139,
1987.

__________________________________________________________________________________________
[4] R.K.Dubey and A.C.Rao, “New Characteristic
polynomial – A Reliable Index to Detect Isomorphism
between Kinematic Chains,” Journal Indian Institute of
Sciences, vol. 66, pp. 227-233,1986.
[5] A.G.Ambekar and V.P.Agrawal, “On Canonical
Numbering of Kinematic Chains and Isomorphism
Problem:Max Code,” ASME paper no. 86-DET-169.
[6] A.G.Ambekar and V.P.Agrawal, “Canonical
Numbering of Kinematic Chains and Isomorphism
Problem:Min Code,” Mechanism and Machine Theory,
no. 22,pp. 463-461,1987.
[7] A.C.Rao and D.V.Raju, “Application of the Hamming
Number Technique to Detect Isomorphism among
Kinematic Chains and Tnversions,” Mechanism and
Machine Theory, no. 26, pp. 55-75, 1991.
[8] A.C.Rao and C.N.Rao “Loop Based Pseudo Hamming
Values-1.Testing Isomophism and Rating Kinematic
Chains,” Mechanism and Machine Theory, 1993.
[9] A.C.Rao and A.Jagadeesh, “Isomorphism, Inversions,
Symmetry and Parallelism with Particular Reference to
Manipulators” IE(I) Journal-MC, vol.80,pp.70-
73,1999.
[10] A.C.Rao and J. Anne, “Topology Based
Characteristics of Kinematic Chains; Workspace
Rigidity, Input-Joint and Isomorphism,” Mechanism
and Machine Theory, no. 33, pp. 625-638, 1988.
[11] J.K.Chu and W.-Q. Cao,” Identification of
Isomorphism among Kinematic Chains and Inversions
using Link,s Adjacent-Chain-Table,” Mechanism and
Machine Theory , vol. 29, no.1, pp. 53-58,1994.
[12] H.Ding and Z.Huang, “The Establishment of the
Canonical Perimeter Topological Graph of Kinematic
Chains and Isomorphism Identification,” ASME
Journal of Mechanical Design,p.915, 2007.
[13] H.Ding and Z.Huang, “Isomorphism Identification of
Graph; Especially for Graph of Kinematic Chains,”
Mechanism and Machine Theory , vol. 44, pp. 122-139,
2009.
[14] G.G.Marin, D.L. Rodriguez and E.M Casermeiro,
“A New Multivalued Neural Network for Isomorphism
Identification of Kinematic Chains,” ASME Journal of
COMPUTING and Information Science in Engineering,
2010.
[15] A.C.Rao, “A Genetic Algorithm for Topological
Characteristics of Kinematic chains,” ASME Journal of
Mechanical Design,p.228, 2000.
[16] R.Xiao, Z.Tao and Y. Liu, “Isomorphism
Identificationof Kinematic Chains Using Novel
Evolutionary Approaches,” ASME Journal of
Computing and Information Science in Engineering,
P.18, 2005,
[17] T.S.Mruthyunjaya, “Kinematic Structure of
Mechanisms Revisited,” Mechanism and Machine
Theory, vol. 38, pp, 279-320, 2003
[18] K.Vijayanand “Computer aided structural synthesis of
linkages and epicyclic gear transmissions,” Ph.D thesis,
IISc, Bangalore.
[19] V.P. Agrwal , J.N. Yadav, C.R.Pratap, “Mechanism
of Kinematic Chain and Degree of Structural Similarity
based on the concept of Link-Link- path Code”,
Mechanism and Machine Theory, 31(7),pp. 865-871,
1996.

Identification of isomorphism and detection of distinct mechanism of kinematic chains using invarient labeling of links

More Related Content

What's hot (16)

Similar to Identification of isomorphism and detection of distinct mechanism of kinematic chains using invarient labeling of links (20)

More from eSAT Journals (20)

Recently uploaded (20)

Identification of isomorphism and detection of distinct mechanism of kinematic chains using invarient labeling of links