IES_SD_led stds_b-2

IES San Diego 2011 Products Show Can’t go to Lightfair? Join us for an industry mixer and lighting products showcase. Enjoy drinks and hors d’oeuvres while visiting with over 70 lighting manufacturers. Omni Hotel 675 L Street, San Diego June 16 th , 2011 5pm – 9pm No host bar This year we are offering a free course from 4-5 pm. Joe Raines from Con-Tech Lightingwill be presenting LED Lighting Technology and Application . Need AIA, LU or CEU credits? Ample parking directly across the street

The applicability of relevant, developing IES Standards as they pertain, both individually and collectively, to light emitting diodes, modules, systems (and luminaires incorporating such appurtenances) with respect to recommended practices and design criteria.

What the heck does all this LED stuff mean anyway?

What Are The Three Relevant Standards?

TM-21 LM-80 LM-79 What Are The Three Relevant Standards?

It’s Not About Being Relevant to Industry Anymore…

Q: Are The Standards Relevant to Design?

Total Lumens Total Power Correlated Color Temperature Color Rendering Index (CRI)

Baseline Shift in Photometry Relative Absolute

Why we Need Absolute Photometry 12vac 700ma 3V f 3 LEDs 3 LEDs 12vdc 350ma 3V f 3 LEDs 3 LEDs 12vac 500ma 2.6V f 3 LEDs 3 LEDs

LM-79 Light isn’t measured in Watts Anymore…

Light emitting diodes (LED’s) are a new and exciting light source of the future. LED’s are an electronic device and require specific equipment and specific system designs to ensure the high lumen output and the very long life are attained and maintained. Real thermal management is very important to maintain the high lumen output, long life and chromaticity consistency. In order to ensure specification integrity the entire lighting system must be tested. This means that the LED must be mounted to its electronic board, the electronic board mounted to its substrate, the solid-state driver installed and the optics mounted. All of the system components must then be enclosed in a light fixture for its intended use. The Illuminating Engineering Society of North America developed testing standards LM79-08 Approved Method: Electrical and Photometric Measurements of Solid-State Lighting Products that allows for the testing of what B-K Lighting and TEKA Illumination call BKSSL™ Technology . The LM79 test data allows the specifier or end user to evaluate the suitability of the SSL lighting system for its use in a particular application or to compare SSL lighting systems against one another. LM79 provides for the total luminous fl ux, electrical power, efficacy and chromaticity. Why is this important with LED’s? We have used relative photometry for years to design our lighting systems. Why a new system? Relative photometry utilizes a lighting manufacturers standard product, photometric testing is accomplished using a reference lamp and a reference ballast or transformer if required. Therefore relative photometry does not provide electrical power information. It also does not take into account heat characteristics of the system regarding efficacy or chromaticity. In fact it does not provide chromaticity characteristics at all. All of these issues are very important when evaluating SSL systems. Absolute photometry requires the lighting manufacture to submit the complete SSL lighting system for measurement so that the resulting data reflects the actual flux, colorimetric performance and the electrical power measurements of the lighting fi xture packaged for its……… TECHNICAL REPORT LM-79 and LM-80 November 30, 2009 Document Number 11-30-09 LM-79

Takeaway: The only way to compare LED luminaire performance is with absolute photometry.

Lumen Depreciation Color Depreciation Over Time For the Light Source Only

“ Whose LEDs do you use?” is a largely irrelevant question.

LM-80 TECHNICAL REPORT LM-79 and LM-80 November 30, 2009 Document Number 11-30-09 “ My LED’s will last for 50,000 hours.” “My LED’s will last for 100,000 hours.” We have all heard these claims. The truth is that an LED being an electronic device with no moving parts could theoretically last forever. Three things can kill a LED. Heat, dirty power and moisture will all have detrimental effects on LED life. In reality, even if LED’s could last forever, their lumen output will diminish over time to a point where they would no longer function as a useful lighting source. We call this “lumen maintenance.” The industry has determined that the LED ceases to be a useful light source when lumen output reduces to 70% of its initial lumens. This is called L70. How do we determine how long this will be? LED manufacturers measure LED’s in pulse mode operation with no heat sink. The pulse is a short 10 to 20 millisecond duration. This does not allow the LED to heat up and the T J is ambient temperature. This allows the LED manufacturer to compare one LED to another with all things being equal. Thus the LED manufacturers data sheets gives you lumen output at T J at 25°C. Because of this testing method we used to hear that the LED manufacturers were “cheating.” This type of testing is not cheating, but it also is not very helpful to the lighting manufacturer who must test the entire system or the designer who must determine if the system is suitable for the application. This is why the Illuminating Engineering Society of North America developed LM80-08 Approved Method: Measuring Lumen Maintenance of LED Light Sources. LM80 covers lumen maintenance measurement for LED packages, arrays and modules. It does not cover any other aspects of LED performance and must be supplied to the lighting manufacturer by the LED manufacturer. This is why B-K Lighting and Teka Illumination will only use LED’s from manufacturers that have tested their LED’s to this standard. IESNA LM80 sets the standards for uniform test methods for LED manufacturers under controlled conditions for measuring LED lumen maintenance while controlling the LED’s case temperature, the forward voltage and forward current to the LED. It also requires the LED manufacturer to measure at a 55°C, 85°C and one other case temperature chosen by the manufacturer, typically at 110°C. It also requires the lumen maintenance data for at least 6,000 hours of constant DC mode operation. The preferred method is 10,000 hours. How do we use this information? LM80 does not speak to this issue, but LED manufacture’s then extrapolate this data to provide lumen maintenance out to L70 or …

Takeaway: Luminaire Design has greatest impact on Lumens, Color, and Life.

Life expectancy (L70) is provided by the luminaire manufacturer. Use test data supplied by the LED manufacturer (LM-80). In Situ temperature measurement of the LED junction (T J ) performed by a qualified testing lab.

The interpolation of this information produces: Expected life of the LED array in the luminaire. At its operating temperature. With the percentage change in CCT and CRI over time. There is no industry standard for the interpolation formula.

TM-21 Doesn’t Exist Yet Still in Committee It’s Been There for 2.5+ Years It Should Allow Mfgs. To Utilize LM80 data Calculate lumen depreciation in their fixture It will standardize on the testing methodology necessary to do so

Takeaway: Maybe We Shouldn’t Have Banned Incandescent So Quickly…

Your Government is Efficient. Trust Them.

Takeaway: USDOE Learned from the mistakes about CFLs.

Nine Questions I Would Ask if I Were a Lighting Designer…

Do You Have LM-79 test data performed by an accredited test lab? Do You Have LM-80 test data performed by the LED manufacturer for the LEDs used in the luminaire? While performing LM-79 testing, did the test lab conduct an in-situ test to determine T J ?

Did you use the LED manufacturer’s recommended formula to determine L70 in the tested luminaire? Have you done an in-situ test of the driver and optics to determine their life expectancies relative to L70? Is the luminaire Energy Star rated? If not, why?

Are you a DOE “SSL Quality Advocate?” Do you have a lighting facts label for the luminaire? What is your warranty? Does it cover the entire SSL system?

IES_SD_led stds_b-2

More Related Content

What's hot (12)

Viewers also liked (6)

Similar to IES_SD_led stds_b-2 (20)

Recently uploaded (20)

IES_SD_led stds_b-2