The ifconfig Command
1 like1,770 views
ifconfig is a command used to configure network interfaces in Linux, BSD, Solaris, and Mac OSX. It displays the status of interfaces, including the IP address, subnet mask, hardware address, and packet transmission/reception statistics. It is used at boot to configure interfaces and can also be used to view interface information or manually configure addresses, change interfaces between up/down states, and set other parameters.
![Syntax
● ifconfig interface [address [parameters]]
● interface is the interface name, such as eth0
(first ethernet device) or lo (local host)
● address is the IP address assigned to the
interface. This can be specified as a dotted
quad address, or as a name that can be
looked up in /etc/hosts.
10](https://image.slidesharecdn.com/ifconfig-100123230036-phpapp02/85/The-ifconfig-Command-10-320.jpg)
The ifconfig Command
- 1. ifconfig Kevin O'Brien Washtenaw Linux Users Group http://www.lugwash.org
- 2. ifconfig ● ... stands for interface configurator ● ... is part of the original internet toolkit http://www.faqs.org/docs/linux_network/x- 087-2-iface.interface.html ● ... has versions available for Linux, BSD, Solaris, and Mac OSX 2
- 3. man page ● Ifconfig is used to configure the kernel-resident network interfaces. It is used at boot time to set up interfaces as necessary. After that, it is usually only needed when debugging or when system tuning is needed. 3
- 4. man page 2 ● If no arguments are given, ifconfig displays the status of the currently active interfaces. If a single interface argument is given, it displays the status of the given interface only; if a single -a argument is given, it displays the status of all interfaces, even those that are down. Otherwise, it configures an interface. 4
- 5. Sample output eth0 Link encap 10Mbps Ethernet HWaddr 00:0F:20:CF:8B:42 inet addr 172.16.1.2 Bcast 172.16.1.255 Mask 255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU 1500 Metric 0 RX packets 3136 errors217 dropped 7 overrun 26 TX packets 1752 errors 25 dropped 0 overrun 0 5
- 6. What is it saying? ● eth0 is the interface it is reporting on. It is the first of the ethernet interfaces on this computer. ● The Hardware Address is 00:0F:20:CF:8B:42. This is sometimes called the MAC address (Media Access Control), and is a hexadecimal number assigned to the ethernet card at the factory. ● The internet address is 172.16.1.2. This is the address assigned to this computer. 6
- 7. What is it saying? 2 ● The Broadcast Address is 172.16.1.255. This is an address that can be used to send messages to every computer on the same subnet as this computer. ● The Subnet Mask is 255.255.255.0. This can be thought of as defining or identifying the subnet this computer is part of. ● The rest of it tells about packets sent, received, dropped, etc. 7
- 8. Use for information ● The first thing most beginners will want to do is use this for information. ● If you find you are not connected to the Internet, use this command to see if your interface is configured and active. ● You can use this to check on your IP address and subnet mask. ● There is an equivalent for wireless interfaces, called iwconfig. 8
- 9. Parallels for newbies ● Windows 95 through ME had a command called winipcfg ● Windows NT through Windows Vista have ipconfig ● These are essentially similar to the Unix command ifconfig 9
- 10. Syntax ● ifconfig interface [address [parameters]] ● interface is the interface name, such as eth0 (first ethernet device) or lo (local host) ● address is the IP address assigned to the interface. This can be specified as a dotted quad address, or as a name that can be looked up in /etc/hosts. 10
- 11. Parameters ● up – Makes an interface accessible to the IP layer. ● down – Makes an interface inaccessible to the IP layer, i.e. stops all traffic through this interface. ● netmask mask – Sets the subnet mask to be used by the interface. ● broadcast address – Sets the broadcast address. 11
- 12. Warning! ● If you are not a network administrator, be very careful about setting addresses from the command line. Even people with some experience can get confused setting a subnet mask. You don't want your interface to stop working in some mysterious way. ● Using this command to get information is completely safe. 12
- 13. Warning! 2 ● If you do want to experiment (a very good way to learn about these things), just make sure you are not using a mission-critical computer. Whatever you screw up you will need to unscrew.☺ 13
- 14. More on this command ● There are other parameters and options available for this command, but they go beyond the requirements for this presentation. Consult Google or the man page for more information. ● A good readable guide to the basics can be found at http://tldp.org/LDP/nag2/x-087-2- iface.ifconfig.html 14
- 15. Examples ● ifconfig eth0 – View the network settings on the first Ethernet adapter installed in the computer. ● ifconfig -a – Display information on all network interfaces on the computer, active or inactive. ● ifconfig eth0 down – Would take down the interface, and no packets would be sent or received. ● ifconfig eth0 up – Would bring the interface back up so it could send and receive data. 15
- 16. Examples 2 ● ifconfig eth0 192.168.1.102 netmask 255.255.255.0 broadcast 192.168.1.255 – This would assign these values to the first Ethernet device installed in the computer. Be careful here! 16