Introduction to TCP / IP model

1
1
An Introduction to
TCP/IP
erhaps the greatest advantage of Linux (and UNIX, in general) is its flexibil-
ity, especially with respect to networking. It was designed to make access easy;
its use of Transmission Control Protocol/Internet Protocol (TCP/IP) network-
ing is in harmony with that design perspective. In this chapter, we will take a
look at networking from an overview perspective and introduce the TCP/IP
model. We will also make a number of definitions and introduce a number of
concepts that we will use throughout this book.
Computer Networking
Networks connect things together. The collection of roads throughout the
United States comprises a network of paths by which vehicles can reach various
points. The purpose of a network of roads is to permit people to efficiently move
from one place to another. Computer networks consist of interconnected com-
puter systems. The purpose of networking these components together is to share
information and computing resources. An obvious example of a computer net-
work is the Internet, in which millions of people access information and com-
puter resources throughout the world. Most of the folks utilizing these resources
have little notion of how those resources are made available to them or what
tasks are required to provide such resources. That, after all, is the job of some
computer jockey−or more formally, a system and/or network administrator.
P
3222K-CH01.fm Page 1 Thursday, July 5, 2001 5:19 PM

2 Chapter 1 ◗ AN INTRODUCTION TO TCP/IP
System and network administrators own the task of ensuring that computer
resources remain available. While the tasks of these two distinct roles often
overlap, it is the job of the network administrator to ensure that computers and
other dedicated network devices, such as repeaters, bridges, routers, and applica-
tion servers, remain interconnected. In order to accomplish this task, the net-
work administrator needs to be familiar with the software and hardware
employed to effectively connect the various components. This familiarity must
begin with the concept of network types and models.
Network Types
There are a number of terms used to describe different types of networks. Such
terms include local area network (LAN), wide area network (WAN), campus
area network (CAN), and metropolitan area network (MAN).
LAN LANs, generally speaking, are collections of interconnected nodes, all
of which are geographically nearby, such as in the same room or in the same
building. A node is any device which can be networked, like a computer (often
referred to as a system), a printer, an appliance (web server, NFS server, etc.), or a
black-box device (usually a router or switchwe define these later in this chap-
ter). It should be noted that with the advent of layer 2 routing (see Chapter 16
for a discussion of layer 2 routing or switching; layers are discussed in the next
section), the notion that the nodes within a LAN must be geographically close
becomes untrue.
WAN A WAN is a collection of interconnected and geographically disparate
nodes. Often, the major distinction between a LAN and a WAN is the use of
some form of high-speed media to interconnect the nodes. Such media includes
microwave, satellite, and telecommunications connections. WAN is a very gen-
eral term that is often applied to collections of LANs and other WANs as well as
collections of nodes. One example is the Internet, which is frequently described
as a WANin fact, the Internet interconnects both LANs and WANs.
CAN The term CAN is usually applied to LANs or WANs that comprise
the collection of interconnected nodes belonging to a single company or univer-
sity/college but whose interconnection extends across many buildings.

Network Models 3
MAN This term is usually applied to the collection of nodes within a metro-
politan area that fall under the same corporate control such as that of a telecom-
munications company or independent service provider (ISP).
If you think that these definitions of LAN, WAN, CAN, and MAN are a bit
fuzzy, good! That’s because they are! Furthermore, it’s likely that they will get
fuzzier as time goes on and technology presses forward.
As a consequence of the fuzziness of these terms, we define the term local net-
work to mean the collection of all nodes connected via the same medium and
sharing the same network number. We formally define network number in “IPv4
Addressing” on page 108, but for now think of sharing the same network num-
ber as meaning that no hardware or software boundaries must be crossed. In
other words, nodes that share the same network number can communicate with
each other without requiring the services of a router (router is defined in “The
Internet Layer” on page 9). The definition of local network given here is synon-
ymous with the definition of link local scope (defined in Chapter 5) and is quite
similar to that of broadcast domain, which is defined in “Broadcast Addresses” on
page 117.
Network Models
Let’s start with a few definitions. A network model reflects a design or architecture
to accomplish communication between different systems. Network models are
also referred to as network stacks or protocol suites. Examples of network models
includes TCP/IP, Sequenced Packet Exchange/Internet Packet Exchange (SPX/
IPX) used by Novelle Netware, the Network Basic Input Output System (Net-
BIOS), which comprises the building blocks for most Microsoft networking and
network applications; and AppleTalk, the network model for Apple Macintosh
computers.
A network model usually consists of layers. Each layer of a model represents
specific functionality. Within the layers of a model, there are usually protocols
specified to implement specific tasks. You may think of a protocol as a set of
rules or a language. Thus, a layer is normally a collection of protocols.
There are a number of different network models. Some of these models relate
to a specific implementation, such as the TCP/IP network model. Others sim-
ply describe the process of networking, such as the International Organization

for Standardization/Open System Interconnection Reference Model (ISO/
OSI-RM, or more simply, OSI-RM).
OSI-RM
The International Organization for Standardization (ISO) is a worldwide body
that promotes standards internationally. In the late 1970s, ISO began work on
developing a standard for multivendor computer interconnectivity. The result,
published in the late 1980s, was the Open System Interconnection (OSI)
model. The OSI model incorporates protocols that can be used to implement a
network stack. These protocols are not used extensively largely due to the popu-
larity of the TCP/IP protocol suite. Consequently, the OSI model, with its well-
defined layers, is used primarily as a reference model, hence, OSI-RM. Many
network models are described by way of OSI-RM and so we provide a descrip-
tion of it here. The OSI-RM is depicted in Figure 1–1.
Figure 1–1 The OSI-RM
Application
Transport
Network
Data Link
Physical
Presentation
Session
Layer 7: The Application layer within which all network applications reside.
Layer 6: The Presentation layer provides data representation support.
Layer 5: The Session layer provides for data exchange through dialogs.
Layer 4: The Transport layer provides end-to-end communication.
Layer 3: The Network layer provides internetwork connectivity.
Layer 2: The Data Link layer provides protocols for transmitting and receiving
data between directly linked systems.
Layer 1: The Physical layer dictates the physical characteristics of communication.

Network Models 5
As indicated in Figure 1–1, each of the layers are numbered 1 through 7 from
physical to application layer.
LAYER 7 All of the capabilities of networking begin in the Application layer.
File transfer, messaging, web browsing, and other applications are in this layer.
Each such application will appropriately invoke processing of data for transmis-
sion through well-defined interfaces to layer(s) below this one.
LAYER 6 The Presentation layer is responsible for data formatting. It takes
care of such things as bit and byte ordering and floating point representation.
Examples include External Data Representation (XDR) and Abstract Syntax
Notation (ASN).
LAYER 5 The Session layer handles the exchange of data through dialog pro-
cedures or chat or conversation protocols. This layer is largely designed for
mainframe and terminal communications. It has no relevance with respect to
TCP/IP networking.
LAYER 4 The Transport layer is responsible for the reliable transfer of data
between systems. It manages the communication session including flow control,
ordering of information, error detection, and recovery of data.
LAYER 3 The Network layer owns the responsibility of delivering data
between different systems in different interconnected networks (internets1
).
LAYER 2 The Data Link layer provides rules for sending and receiving data
between two connected nodes over a particular physical medium.
LAYER 1 The Physical layer defines the required hardware, such as cables
and interfaces, for a given medium of communication, such as electrical, radio
frequency, and light-based. In this way, methods for transmitting and receiving
bit-streams of information are defined.
1. The term Internet (upper case I) is used to reference the public internetwork. The term
internet (lower case i) is used to generally describe a collection of interconnected networks of
which the Internet is one example.

NOTE
There is a great deal more to the OSI model than we have discussed here.
For complete details on this standard, visit
http://www.iso.ch/cate/3510001.html
Also, see “For Further Reading” on page 15 for more resources on this topic.
Next, we discuss the TCP/IP model and begin our journey into the world of
TCP/IP networking. We will compare it with the OSI model at the end of the
next section.
The TCP/IP Network Model
The TCP/IP network model takes its name from two of its protocols, the Trans-
mission Control Protocol (TCP) and the Internet Protocol (IP). Figure 1–2 pro-
vides a five-layer2 representation of the TCP/IP Model. By utilizing a five-layer
model, the lower four layers are numbered identically to the lower four layers of
the OSI-RM model.
The lower four layers of the model represent functionality performed internally
by the Linux kernel.The Application layer includes commands and daemons.
The process of initiating a network communication, like executing telnet
hostname, causes the initiator (usually the client) to encapsulate application data,
beginning at the top of the model and moving down, for the network transmis-
sion. In other words, each layer wraps the data passed to it by the previous layer
with information used to determine where the packet is supposed to go and
which service needs to be invoked to handle the application data itself. The
information added by each layer is called a header when it is prefixed to the data
from the previous layer, and a trailer when it is suffixed. On the left-hand side of
Figure 1–2, you see an increasing number of rectangles as you scan down the
layers. The area in gray represents the information added by each layer.
The receiving system, normally the server, performs the same steps except in
reverse (bottom to top), deencapsulating the data. Each layer is responsible for
2. Many texts will use a four-layer representation, combining the Hardware and Network
Interface layers.

Network Models 7
interpreting the header generated by the same layer on the sending system. This
process is known as peer-to-peer communication.
The information produced during encapsulation, or read during deencapsula-
tion by each layer is ascribed a name as shown in Figure 1–2. For Layer 5, if the
underlying Transport layer protocol is the TCP, then the data produced or read
by Layer 5 is called a stream; if the underlying Transport layer protocol is the
User Datagram Protocol (UDP), then it is called a message. For Layer 4, if the
protocol used is TCP, then the data produced or read by Layer 4 is called a seg-
ment. Otherwise, if it is UDP, then it is called a packet. The data of Layer 3 is
called a datagram; of Layer 2, a frame or cell; and of Layer 1, a signal.
NOTE
The term packet is commonly used instead of signal and/or frame.
In the following sections, we will briefly review the information generated by
each layer and its purpose.
Figure 1–2 The TCP/IP Model
Transport Layer
Header (TLH)
Application
Layer 5
Transport
Layer 4
Internet
Layer 3
Network Interface
Layer 2
Hardware
Layer 1
data
Encapsulation
Internet Layer
Header (ILH) data
Net I’face Layer
Header (NILH)
Preamble
data
data CRC
TLH
CRC
ILH
ILH
TLH
TLH
frame
signal
datagram
TCP=stream
UDP=message
TCP=segment
UDP=packet
NILH
data

The Hardware Layer
The Hardware layer is responsible for exactly thathardware. This includes
cables, interface cards, and repeaters. It accepts the data passed to it by the Net-
work Interface layer and prefixes something called the Preamble, which is a well-
known sequence of 64 bits used for synchronization purposes. When it finishes
its work, it generates a signal to be submitted to the media (electrically-based
cables in most cases). The Hardware layer also imposes the maximum transfer
unit (MTU) used by the Internet layer to ensure that the Hardware layer does
not get frames3 that are too large or too small. For Ethernet, the MTU for the
signal is 1526 octets, and the minimum signal size is 72 octets.4
There are two hardware devices which operate at this layer: repeaters and
amplifiers. A repeater is a device with a number of ports (usually four or more)
that is capable of receiving signals, filtering out noise (phenomena not related to
the communication at hand), and repeating the signals to every port except the
ingress (incoming) port. Amplifiers perform the same task, except that they do
not filter noise. Consequently, repeaters are employed in electrical communica-
tions environments and amplifiers are employed in light-based communications
environments. These devices are often called hubs or concentrators. We will dis-
cuss this layer in greater detail in Chapter 2.
The Network Interface Layer
You may think of the Network Interface layer as a collection of device drivers.
Its responsibility is to prepare the data passed to it from the Internet layer for
signaling. It does this by prefixing its header (indicated as NILH in Figure 1–2),
computing a Cyclic Redundancy Check (CRCa 32-bit checksum), appending
the CRC to the datagram, and passing this information to the device (interface)
for signaling in what is called a frame. In particular, this layer understands phys-
ical addresses (often referred to as Media Access Control [MAC] addresses).
When using Ethernet, this is often called an Ethernet address. Physical
3. The data of the Network Interface layer is called a frame when it varies in size. More for-
mally, when using Ethernet, it should be called an Ethernet frame. Fixed size data at this layer,
such as that used by Asynchronous Transfer Mode (ATM), is called a cell.
4. MTU is further discussed throughout the next several chapters, but note that it is more
common to quote the Ethernet frame MTU, which is 1518 octets. The minimum Ethernet
frame size is 64 octets. Note that frames occur at the Network Access layer. Here we are describ-
ing the Hardware layer.

Network Models 9
addresses are local and only need to be unique within the local network. For
Ethernet interface chipsets, they are 48-bit addresses permanently written into
the programmable read-only memory (PROM).
The Network Interface layer writes both the destination and source physical
address into its header during encapsulation. Consequently, it is at this layer
that, during deencapsulation, initial decisions are made about whether or not to
continue processing an incoming frame up the stack. This is discussed in detail
in Chapter 2.
There is one device associated with this layer. It is a switch. Switches look very
much like repeaters, a piece of hardware with at least two network ports, but are
more intelligent than repeaters. Since they operate at the Network Interface
layer, they are able to make decisions based on physical addresses. Switches are
sometimes called hubs or bridges or layer 2 routers.
NOTE
Switches are sometimes called bridges (or the other way around, if you
like). Bridge is an older term that is not commonly used today. Unfortu-
nately, the terms switching, layer 2 switching, and layer 3 switching all con-
found the issue of what is really being described. Most of the variation in
the base term “switch” comes from vendors of switches and routers. An
argument could be made that the proper term for the layer 2 device that is
capable of making packet-forwarding decisions based on physical
addresses is “bridge.” A similar argument could be made for the term
switch. I could coin a new term, say swidge, but I haven’t got the courage,
and, besides, it would probably make matters worse. After all, companies
like Cisco aren’t likely to change their terminology just because I say so.
I had to make a decision about which term to use. So I decided to use
switch. Throughout this book, I will make no distinction between bridge
and switch and will use the term switch to mean a layer 2 device that is capa-
ble of making packet-forwarding decisions based on physical addresses.
The Internet Layer
The Internet layer is responsible for a variety of tasks. In order to accomplish
these tasks it uses three principal protocols. The Internet Protocol (IP), the
Internet Control Messaging Protocol (ICMP), and the Internet Group Man-

agement Protocol (IGMP). The IP is responsible for routing and fragmentation.5
The ICMP generates error messages, assists routing through redirection, may
implement rudimentary flow control, supports the ping command, supports
router discovery, and may generate timestamp and netmask queries and
responses. The IGMP supports Internet Layer multicasting. Each of these pro-
tocols has two available versions: 4 and 6.
The device that operates at this layer is a router. Routers are nodes that imple-
ment the intelligence of the Internet layer protocols and forward datagrams to the
appropriate networks or subnetworks (discussed in Chapter 4) based on IP addresses
and the routing algorithm (described in Chapter 6). Routers are sometimes called
layer 3 switches. Unfortunately, routers are also sometimes called hubs.
The Internet layer produces or reads the Internet layer header. The header
contains a lot of information and, in particular, includes the source and destina-
tion IP address associated with the packet. There are two versions of the proto-
cols in this layer: version 4 and version 6. IPv4 addresses are 4 octets while IPv6
addresses are 16 octets. These are global addresses, meaning that all nodes
throughout a collection of networks that are interconnected (internet) must be
uniquely identified by this address. Data is passed through such an internet by
the process of routing. Routing is performed by examining a portion of an IP
address in order to determine to which network the data needs to be sent (effec-
tively the purpose of the routing algorithm). Linux systems can act as routers.
This header, together with the overall functionality of the Internet layer, is
largely discussed in Chapters 4, 5, and 6. Additional details of the Internet layer
and Linux router functionality are given in the last six chapters of this book.
The Transport Layer
The Transport Layer is responsible for the end-to-end flow of data. There are
two primary protocols used within this layer (TCP and the UDP). An applica-
tion will use one or the other of these protocols for a given communication.
These protocols, the headers they produce or read, and the Transport layer are
described in Chapter 7.
5. Fragmentation applies to IP version 4 only.

Network Models 11
The Application Layer
This is the layer where all the applications live. These applications are responsi-
ble for understanding the data format as well as interpreting the data. Example
applications include the Domain Name Service (DNS), the Dynamic Host
Configuration Protocol (DHCP), the Network File System (NFS), Samba,
electronic mail (e-mail), the file transfer protocol (FTP), and the telnet utility.
The Application layer is discussed in Chapter 8.
The device that operates at this layer is the gateway. Unfortunately, gateway is
a term, somewhat like hub, that is used in many ways. We generally define it to
mean a link between distinct and/or different computer networks. Often, it is
used to refer to a system that is capable of converting from one network protocol
stack to another, such as a system that is interconnected into both a TCP/IP
network and a Netware network. Gateway is often used to refer to a system that
interconnects an internal internetwork and an external network such as the
Internet. Other uses of the term gateway are described as they arise.
OSI-RM and TCP/IP Model Comparison
Figure 1–3 depicts the relationship between the OSI-RM and the TCP/IP
model.
The relationship between these two models at Layers 1, 2, and 3 is identical.
While the diagram in Figure 1–3 shows a one-to-one correspondence at Layer
4, it should be noted that UDP does not perform all of the functions required by
the OSI-RM Transport layer; we will explore this fact further in Chapter 7.
The Application layer of the TCP/IP model assumes responsibility for the
Session, Presentation, and Application layer of the OSI-RM. This relationship
will be detailed further in Chapter 8 and numerous subsequent chapters.
One of the advantages of depicting the TCP/IP model as a five-layer model is
that we can refer to Layer 1, 2, and 3 of both models. We will do so throughout
this book.

The Client-Server Model
It may be rather like stating the obvious, but we define the terms server and cli-
ent. A server is a network node that makes compute or data resources available.
A client is a network node that utilizes server resources. Of course, for clients
and servers to interact, they must be interconnected.
Nodes may act in one, both, or neither capacity of server and client. Generally
speaking, from the Linux perspective, the client is the system upon which a
command invoking a network-based application is executed. The server is the
system on which a daemon is running. A daemon is a special program that
responds to and handles resource requests. Throughout this book we will deal
with, and further refine, these terms.
Request for Comment
The vast majority of the protocols and standards that we discuss throughout this
book are embodied in a Request for Comment (RFC), more specifically, an
Figure 1–3 OSI-RM and TCP/IP Comparison
OSI-RM
Application
Transport
Network
Data Link
Physical
Presentation
Session
TCP/IP
Transport
Internet
Network Interface
Hardware
Application
Layer 4
Layer 3
Layer 2
Layer 1
Layer 7
Layer 6
Layer 5
Layer 5
}

Institute of Electrical and Electronics Engineers (IEEE) 13
RFC developed and/or maintained by the Internet Engineering Task Force
(IETF).
The overall controlling entity for Internet standards is the Internet Society
(ISOC). The Internet Architecture Board (IAB) and the IETF both fall under
the ISOC. The IETF does the actual technical work while the IAB handles a
lot of the administrative details. The Internet Engineering Steering Group
(IESG), also part of the ISOC, provides technical direction for the IAB and the
IETF. Our interest is with the work of the IETF and, in particular, with RFCs
that provide a standard that is implemented in TCP/IP networking. In addition
to standards track RFCs (RFCs that have been approved as standards or are
becoming standards), the IETF also produces informational and best current
practice RFCs that provide details about the implementation and use of some
technology without being a standard. You can learn more about the IETF and
the associated organizations discussed in this paragraph at
http://www.ietf.org/
For complete details about IETF RFCs, please see the site
http://www.ietf.org/rfc.html
A search engine for RFCs can be found at
http://www.rfc-editor.org/
Where appropriate, we will discuss specific RFCs at various points in this
book.
There is another type of RFC maintained by an organization called the Open
Group. The Open Group RFCs also define standards and protocols, but are less
common. For further information regarding the Open Group RFCs, please visit
http://www.opengroup.org/rfc/
Throughout this document, all RFCs are IETF RFCs unless specifically
identified as an Open Group RFC.
Institute of Electrical and Electronics Engineers (IEEE)
The IEEE is a non-profit technical organization that, among other things, pro-
motes standards for a variety of computing technologies, largely at layers 1 and 2
of the TCP/IP stack. We will be referring to their standards throughout this
text. You can learn more about IEEE at their home and standards pages:

http://www.ieee.org/
http://standards.ieee.org/
Throughout this book we will reference a variety of standards from the IEEE.
Table 1–1 lists the high-level IEEE standard number and its general coverage of
each standard number.
For complete coverage of these standards, see the IEEE Web sites referenced
above.
There is an excellent write-up of the topics discussed in the last six chapters of
this book, including the relationship between IEEE standards and the lower
layer ISO standards, at
http://www.cs.herts.ac.uk/~simon/networks1/node1.html
Table 1–1 IEEE High-Level Standards
STANDARD
NUMBER
DESCRIPTION
802.1 High-level architectural overview
802.2 Logical link control (LLC)
802.3 Ethernet with CSMA/CD
802.4 Token bus
802.5 Token ring
802.6 MANs
802.7 Broadband LANs
802.8 Fiber optic LANs
802.9 Data and voice network integration
802.10 Security and privacy
802.11 Wireless networking

The Internet, TCP/IP, and Other Stacks 15
The Internet, TCP/IP, and Other Stacks
Only a few short years ago you would have been hard-pressed to find 10 people
outside of the computer industry who knew about the Internet. Today, it is
nearly taken for granted.
The Internet is a global collection of WANs and LANs that are all intercon-
nected. Participation in the Internet ultimately requires TCP/IP capability in
the form of a node acting as an Internet gateway or portal. From that perspec-
tive, TCP/IP is the network stack of the Internet. There are other network
stacks at play within the Internet, and indeed, in a variety of roles throughout
the computer industry.
Summary
In this chapter we introduced the OSI-RM and TCP/IP model, briefly
described each of their layers, and compared the two models. Additionally, we
introduced the client-server model and RFCs. We also defined a number of
terms that we will use throughout this text.
For Further Reading
Listed below are books and WWW resources that provide further information
about the topics discussed in this chapter.
Books
Comer, Douglas E., Internetworking with TCP/IP Vol I: Principals, Protocols,
Architecture, 3rd. ed., Englewood Cliffs, New Jersey, Prentice Hall, 1995.
Huitema, Christian, Routing in the Internet, Englewood Cliffs, New Jersey, Prentice
Hall PTR, 1995.
Perlman, Radia, Interconnections, Second Edition: Bridges, Routers, Switches, and
Internetworking Protocols, Reading, Massachusetts, Addison-Wesley, 2000.
Stevens, W. Richard, TCP/IP Illustrated, Volume 1: The Protocols, Reading,
Massachusetts, Addison-Wesley, 1994.

WWW Resources
You will find OSI information at the ISO home page:
http://www.iso.ch/
IETF RFCs can be found at
http://www.ietf.org/rfc.html
and Open Group RFCs at
http://www.opengroup.org/rfc/
For IEEE standards and information, see their home page or standards page:
http://www.ieee.org/
http://standards.ieee.org/

Introduction to TCP / IP model

More Related Content

Similar to Introduction to TCP / IP model (20)

Recently uploaded (20)

Introduction to TCP / IP model