Introto plcs
- 1. Lecture – Introduction to PLC's MME 486 – Fall 2006 1 of 47 Introduction to Programmable Logic Controllers (PLC's) Industrial Control Systems Fall 2006
- 2. Lecture – Introduction to PLC's MME 486 – Fall 2006 2 of 47 The Need for PLCs • Hardwired panels were very time consuming to wire, debug and change. • GM identified the following requirements for computer controllers to replace hardwired panels. – Solid-state not mechanical – Easy to modify input and output devices – Easily programmed and maintained by plant electricians – Be able to function in an industrial environment
- 3. Lecture – Introduction to PLC's MME 486 – Fall 2006 3 of 47 The First Programmable Logic Controllers (PLCs) • Introduced in the late 1960’s • Developed to offer the same functionality as the existing relay logic systems • Programmable, reusable and reliable – Could withstand a harsh industrial environment – They had no hard drive, they had battery backup – Could start in seconds – Used Ladder Logic for programming
- 4. Lecture – Introduction to PLC's MME 486 – Fall 2006 4 of 47 Programmable Logic Controller • A programmable logic controller (PLC) is a specialized computer used to control machines and process. • It uses a programmable memory to store instructions and specific functions that include On/Off control, timing, counting, sequencing, arithmetic, and data handling
- 5. Lecture – Introduction to PLC's MME 486 – Fall 2006 5 of 47 Advantages of PLC Control Systems • Flexible • Faster response time • Less and simpler wiring • Solid-state - no moving parts • Modular design - easy to repair and expand • Handles much more complicated systems • Sophisticated instruction sets available • Allows for diagnostics “easy to troubleshoot” • Less expensive
- 6. Lecture – Introduction to PLC's MME 486 – Fall 2006 6 of 47 Advantages of a PLC Control System Eliminates much of the hard wiring that was associated with conventional relay control circuits. The program takes the place of much of the external wiring that would be required for control of a process.
- 7. Lecture – Introduction to PLC's MME 486 – Fall 2006 7 of 47 Advantages of a PLC Control System Increased Reliability: Once a program has been written and tested it can be downloaded to other PLCs. Since all the logic is contained in the PLC’s memory, there is no chance of making a logic wiring error. Conversely ......
- 8. Lecture – Introduction to PLC's MME 486 – Fall 2006 8 of 47 Advantages of a PLC Control System More Flexibility: Original equipment manufacturers (OEMs) can provide system updates for a process by simply sending out a new program. It is easier to create and change a program in a PLC than to wire and rewire a circuit. End-users can modify the program in the field.
- 9. Lecture – Introduction to PLC's MME 486 – Fall 2006 9 of 47 Advantages of a PLC Control System Lower Costs: Originally PLCs were designed to replace relay control logic. The cost savings using PLCs have been so significant that relay control is becoming obsolete, except for power applications. Generally, if an application requires more than about 6 control relays, it will usually be less expensive to install a PLC.
- 10. Lecture – Introduction to PLC's MME 486 – Fall 2006 10 of 47 Advantages of a PLC Control System Communications Capability: A PLC can communicate with other controllers or computer equipment. They can be networked to perform such functions as: supervisory control, data gathering, monitoring devices and process parameters, and downloading and uploading of programs.
- 11. Lecture – Introduction to PLC's MME 486 – Fall 2006 11 of 47 Advantages of a PLC Control System Faster Response Time: PLCs operate in real-time which means that an event taking place in the field will result in an operation or output taking place. Machines that process thousands of items per second and objects that spend only a fraction of a second in front of a sensor require the PLC’s quick response capability.
- 12. Lecture – Introduction to PLC's MME 486 – Fall 2006 12 of 47 Advantages of a PLC Control System Easier To Troubleshoot: PLCs have resident diagnostic and override functions allowing users to easily trace and correct software and hardware problems. The control program can be watched in real-time as it executes to find and fix problems
- 13. Lecture – Introduction to PLC's MME 486 – Fall 2006 13 of 47 PLC Architecture
- 14. Lecture – Introduction to PLC's MME 486 – Fall 2006 14 of 47 PLC System
- 15. Lecture – Introduction to PLC's MME 486 – Fall 2006 15 of 47 PLC Architecture • An open architecture design allows the system to be connected easily to devices and programs made by other manufacturers. • A closed architecture or proprietary system, is one whose design makes it more difficult to connect devices and programs made by other manufacturers. NOTE: When working with PLC systems that are proprietary in nature you must be sure that any generic hardware or software you use is compatible with your particular PLC.
- 16. Lecture – Introduction to PLC's MME 486 – Fall 2006 16 of 47 I/O Configurations Fixed I/O • Is typical of small PLCs • Comes in one package, with no separate removable units. • The processor and I/O are packaged together. • Lower in cost – but lacks flexibility.
- 17. Lecture – Introduction to PLC's MME 486 – Fall 2006 17 of 47 I/O Configurations Modular I/O Is divided by compartments into which separate modules can be plugged. This feature greatly increases your options and the unit’s flexibility. You can choose from all the modules available and mix them in any way you desire.
- 18. Lecture – Introduction to PLC's MME 486 – Fall 2006 18 of 47 I/O Configurations Modular I/O When a module slides into the rack, it makes an electrical connection with a series of contacts - called the backplane. The backplane is located at the rear of the rack.
- 19. Lecture – Introduction to PLC's MME 486 – Fall 2006 19 of 47 Power Supply • Supplies DC power to other modules that plug into the rack. • In large PLC systems, this power supply does not normally supply power to the field devices. • In small and micro PLC systems, the power supply is also used to power field devices.
- 20. Lecture – Introduction to PLC's MME 486 – Fall 2006 20 of 47 Processor (CPU) Processor Module • Is the “brain” of the PLC. • Consists of a microprocessor for implementing the logic, and controlling the communications among the modules. • Designed so the desired circuit can be entered in relay ladder logic form. • The processor accepts input data from various sensing devices, executes the stored user program, and sends appropriate output commands to control devices.
- 21. Lecture – Introduction to PLC's MME 486 – Fall 2006 21 of 47 I/O Section Consists of: • Input modules • Output modules.
- 22. Lecture – Introduction to PLC's MME 486 – Fall 2006 22 of 47 I/O Section Input Module • Forms the interface by which input field devices are connected to the controller. • The terms “field” and “real world”are used to distinguish actual external devices that exist and must be physically wired into the system.
- 23. Lecture – Introduction to PLC's MME 486 – Fall 2006 23 of 47 I/O Section Output Module • Forms the interface by which output field devices are connected to the controller. • PLCs employ an optical isolator which uses light to electrical- ly isolate the internal components from the input and output terminals.
- 24. Lecture – Introduction to PLC's MME 486 – Fall 2006 24 of 47 Programming Device PC with appropriate software • A personal computer (PC) is the most commonly used programming device • The software allows users to create, edit, document, store and troubleshoot programs • The personal computer communicates with the PLC processor via a serial or parallel data communications link
- 25. Lecture – Introduction to PLC's MME 486 – Fall 2006 25 of 47 Programming Device Hand-held unit with display • Hand-held programming devices are sometimes used to program small PLCs • They are compact, inexpensive, and easy to use, but are not able to display as much logic on screen as a computer monitor
- 26. Lecture – Introduction to PLC's MME 486 – Fall 2006 26 of 47 Programming Device • Hand-held units are often used on the factory floor for troubleshooting, modifying programs, and transferring programs to multiple machines. Hand-held unit with display
- 27. Lecture – Introduction to PLC's MME 486 – Fall 2006 27 of 47 PLC Mixer Process Control Problem Mixer motor to automatically stir the liquid in the vat when the temperature and pressure reach preset values Alternate manual pushbutton control of the motor to be provided The temperature and pressure sensor switches close their respective contacts when conditions reach their preset values
- 28. Lecture – Introduction to PLC's MME 486 – Fall 2006 28 of 47 Process Control Relay Ladder Diagram Motor starter coil is energized when both the pressure and temperature switches are closed or when the manual pushbutton is pressed
- 29. Lecture – Introduction to PLC's MME 486 – Fall 2006 29 of 47 PLC Input Module Connections • The same input field devices are used • These devices are wired to the input module according to the manufacturer’s labeling scheme
- 30. Lecture – Introduction to PLC's MME 486 – Fall 2006 30 of 47 PLC Output Module Connections Same output field device is used and wired to the output module Triac switches motor ON and OFF in accordance with the control signal from the processor Triac
- 31. Lecture – Introduction to PLC's MME 486 – Fall 2006 31 of 47 PLC Ladder Logic Program • The format used is similar to that of the hard-wired relay circuit
- 32. Lecture – Introduction to PLC's MME 486 – Fall 2006 32 of 47 PLC Ladder Logic Program The symbols represent instructions
- 33. Lecture – Introduction to PLC's MME 486 – Fall 2006 33 of 47 PLC Ladder Logic Program The numbers represent addresses
- 34. Lecture – Introduction to PLC's MME 486 – Fall 2006 34 of 47 PLC Ladder Logic Program • I/O address format will differ, depending on the PLC manufacturer. You give each input and output device an address. This lets the PLC know where they are physically connected
- 35. Lecture – Introduction to PLC's MME 486 – Fall 2006 35 of 47 Entering And Running The PLC Program To enter the program into the PLC, place the processor in the PROGRAM mode and enter the instructions one-by-one using the programming device To operate the program, the controller is placed in the RUN mode, or operating cycle
- 36. Lecture – Introduction to PLC's MME 486 – Fall 2006 36 of 47 PLC Operating Cycle During each operating cycle, the controller examines the status of input devices, executes the user program, and changes outputs accordingly The completion of one cycle of this sequence is called a scan. The scan time, the time required for one full cycle, provides a measure of the speed of response of the PLC
- 37. Lecture – Introduction to PLC's MME 486 – Fall 2006 37 of 47 PLC Operating Cycle The can be considered to represent a coil that, when energized, will close a set of contacts. Each can be though of as a set of normally open contacts
- 38. Lecture – Introduction to PLC's MME 486 – Fall 2006 38 of 47 PLC Operating Cycle Coil O/1 is energized when contacts I/1 and I/2 are closed or when contact I/3 is closed. Either of these conditions provides a continuous path from left to right across the rung that includes the coil.
- 39. Lecture – Introduction to PLC's MME 486 – Fall 2006 39 of 47 Modifying A PLC Program Relay ladder diagram for modified process. The change requires that the manual pushbutton control should be permitted to operate at any pressure but not unless the specified temperature setting has been reached.
- 40. Lecture – Introduction to PLC's MME 486 – Fall 2006 40 of 47 Modifying A PLC Program Relay ladder diagram for modified process. If a relay system were used, it would require some rewiring of the system, as shown, to achieve the desired change.
- 41. Lecture – Introduction to PLC's MME 486 – Fall 2006 41 of 47 Modifying A PLC Program PLC ladder logic diagram for modified process. If a PLC is used, no rewiring is necessary! The inputs and outputs are still the same. All that is required is to change the PLC program
- 42. Lecture – Introduction to PLC's MME 486 – Fall 2006 42 of 47 PLC - Operates in the industrial environment - Is programmed in relay ladder logic - Has no keyboard, CD drive, monitor, or disk drive - Has communications ports, and terminals for input and output devices PLCs Versus Personal Computers Same basic architecture PC - Capable of executing several programs simultaneously, in any order - Some manufacturers have software and interface cards available so that a PC can do the work of a PLC
- 43. Lecture – Introduction to PLC's MME 486 – Fall 2006 43 of 47 PC Based Control Systems Advantages - Lower initial cost - Less proprietary hardware and software required - Straightforward data exchange with other systems - Speedy information processing - Easy customization
- 44. Lecture – Introduction to PLC's MME 486 – Fall 2006 44 of 47 PLC Size Classification Criteria - Number of inputs and outputs (I/O count) - Cost - Physical size Nano PLC - Smallest sized PLC - Handles up to 16 I/O points Micro PLC - Handles up to 32 I/O points
- 45. Lecture – Introduction to PLC's MME 486 – Fall 2006 45 of 47 Allen-Bradley PLC-5 Family - Handles several thousand I/O points Allen-Bradley SLC-500 Family - Handles up to 960 I/O points PLC Size Classification
- 46. Lecture – Introduction to PLC's MME 486 – Fall 2006 46 of 47 PLC Instruction Set The instruction set for a particular PLC type lists the different types of instructions supported. An instruction is a command that will cause a PLC to perform a certain predetermined operation.
- 47. Lecture – Introduction to PLC's MME 486 – Fall 2006 47 of 47 Typical PLC Instructions XIC (Examine ON) . . . . . . . Examine a bit for an ON condition XIO (Examine OFF) . . . . . . Examine a bit for an OFF condition OTE (Output Energize) . . . . Turn ON a bit (non retentive) OTL (Output Latch) . . . . . . Latch a bit (retentive) OTU (Output Unlatch) . . . . Unlatch a bit (retentive) TOF (Timer Off-Delay) . . . . . Turn an output ON or OFF after its rung has been OFF a preset time interval TON (Timer On-Delay) . . . . Turn an output ON or OFF after its rung has been ON for a preset time interval CTD (Count Down) . . . . . . . Use a software counter to count down from a specified value CTU (Count Up) . . . . . . . . . Use a software counter to count up to a specified value