IRJET- Air Pollution Monitoring System using IoT

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 07 Issue: 02 | Feb 2020 www.irjet.net p-ISSN: 2395-0072
© 2020, IRJET | Impact Factor value: 7.34 | ISO 9001:2008 Certified Journal | Page 1180
Air Pollution Monitoring System Using IoT
R. Abirami1, M. Sandhiya2, Dr. V. Jaiganesh3
1PG Student, Department of Computer Science, Dr.N.G.P Arts and Science College, Tamil Nadu, India
2PG Student, Department of Computer Science, Dr.N.G.P Arts and Science College, Tamil Nadu, India
3Associate professor, Department of Computer Science, Dr.N.G.P Arts and Science College, Tamil Nadu, India
---------------------------------------------------------------------***---------------------------------------------------------------------
Abstract - Every vehicle has its emission of gases, but the
difficulty is the emission of the gas outside the uniform
values. This emission fromthevehiclescannotbecompletely
avoided, but in certain things, we can able to control this. In
this situation, in most countries, air pollution is a major
problem. In our life there are three needed necessities are
used on earth i.e. air, liquid substances (water), solid
substances (food). Before it consumed the water, the water
permits through a reliable cleaning process. From the
statistics, without significant weather,theairpollutedor not,
living beings that breathe over 3000 tons of air per day.
Therefore this suggests raising awareness to the public
regarding air quality and air pollutants. Because of air
pollution not only human health is affected it also damages
the atmosphere and surroundings so decrease themature of
live hood.
Key Words: Internet of Things, ArduinoUNO,Airpollution,
Gas sensor, Arduino IDE
1. INTRODUCTION
Pollution can be well-defined as the presence of tiny
elements that distracttheworkingofordinaryprocessesand
also yields undesirable health. In other words, pollution can
disturb the natural phase and also can disturb the health of
the living being. Asindustrial developmentisgrowingwidely
pollution is also getting make known to a huge manner. At
present, there is Air, Water, and Soil is polluted worldwide.
This only concentrates on Air pollution. Air pollution is the
being there of impurity or tiny elements that affect living
being health and surroundings. These pollutants resultfrom
vehicles, industries. The WHO (World Health Organization)
states that 2.3 million persons die per year due to reasons
directly qualified by air pollution. Based on the information
above points out, the humanoid shouldfocusonairpollution
observing. Air pollutants are measured in Parts per Million
(ppm) or ug/m3. Primary pollutants are released directly
into the atmosphere. Secondary pollutants are produced
when the primary pollutant reacts with other atmospheric
chemicals. Air quality affects public health [2]. There are
two approaches to checking airpollutionatpresent-day. One
is an inactive sample (non-automatic), and the other is
constant online checking (automatic). The Inactive sample
uses simple tools but it does notdeliver real-timevalues.The
procedure of continuous online monitoring uses sensors to
monitor the parameters, and then send it to the control
center by the network. The way records transmission
includes wired and wireless organizations. Even although
the system is dependable it is consuming small
developments at big and dynamic range, such as complex
network cabling, expensive, etc. at length rising
communication knowledge, now a day’s air pollution
checking method is often aimed in the wireless method. To
implement such a system single-chip microcontroller along
with an array of sensors, the IoT module is used.Thissystem
focus on gases such as CO2, temperature, and humidity via
sensors. The hardware part collects air pollutant stages also
packs them into the frame. The frame is uploaded to the IoT
modem communicated to the significant server via IoT. This
organization is low budget and energy effective in terms of
devices.
2. METHODOLOGY
In this project, we are working to make an IOT Based Air
Pollution Monitoring System in which we will observe the
Air Quality done on mobile using the internet and will
initiate an alarm when the air quality goes beyond a certain
level. When there is a sufficient quantity of dangerous gases
are exist in the air like CO2, smoke, temperature, humidity,
and rain. It will show the air value in Parts per Million(PPM)
on the LCD so that we can display it very easily.
3. HARDWARE COMPONENTS
3.1 Arduino UNO
Fig -1: Arduino UNO
Arduino Uno is a microcontroller board that In this project,
we are working to make an IOT Based Air Pollution
Monitoring System in which we will observe the Air Quality
done on mobile using the internet and will initiate an alarm
when the air quality goes beyond a certainlevel. Whenthere
is a sufficient quantity of dangerous gases are exist in the air

like CO2, smoke, temperature, humidity, and rain. It will
show the air value in Parts per Million (PPM) on the LCD so
that we can display it very easily. The Arduino Uno board
includes 14 digital input/output pins 6 analog inputs, a USB
Connection, a power jack, a reset button. The user
community that designs and manufactures single-board
microcontrollers and microcontrollerkitsfor buildingdigital
devices and interactive objects [3]. The Arduino
microcontroller is not only for technical persons but is
intended for designers and artists also becauseofitsfocus to
usability based on its plan which helps to achieve the
intended goal [5].
3.2 Gas Sensor
Fig -2: Gas Sensor
The Gas Sensor (MQ2) component is used forthegasleakage
finding. It is used for recognizing LPG Liquefied petroleum
gas, CH4, CO (carbon monoxide), Smoke. The circuit is very
simple. Gas sensor of the MQ-2 gas sensor is SnO2 (stannic
oxide), which with lesser conductivity in clean air.
3.3 DTH11 Sensor
Fig -3: DTH11 Sensor
DHT11 is featured to measure temperature and humidity
sensor complex by using temperature & humidity sensing
technique with output in the form of thestandardizeddigital
signal [1]. DHT11 is an inexpensive humidity and
temperature sensor which offers high consistency and long
period steadiness. DHT11 can be interfaced with any
microcontroller like Arduino and get instant results. It gives
the output in voltage.
3.4 LCD
Fig -4: LCD Display
LCD (Liquid Crystal Display) an electronic display module.
This is a basic (16x2) 16 character by 2linedisplay[4].Black
text on Green background. It is used to show the Air and
Humidity. A (16x2) LCD is a very plain module and is very
normally used in different types of devices and circuits [5].
3.5 Buzzer
Fig -5: Buzzer
A Buzzer or beeper is an electronic audio signalling device.
Whenever the air pollution or the toxic level in the air goes
beyond the threshold level the Buzzer makes sound starts
beeping indicating Danger [4].
3.6 Wi-Fi Module
Fig -6: WI-FI Module

The ESP8266 is low-cost. Every ESP8266 component comes
pre-programmed with an AT expertise set firmware,
meaning, we can simply join to the Arduino device. The
ESP8266 module is a low-cost board [5]. This module has a
dominant sufficient on-board processing and storage
capability that allows it to be combined with the sensors.
4. SOFTWARE REQUIREMENTS
4.1 Arduino IDE
The Arduino is an Integrated Development Environment
(IDE) or Arduino Software has a text editor for writing
programs. It also has a message area, text console, a toolbar
with buttons for functions and a series of menus. It links to
the Arduino hardware to upload programs andconnectwith
them [6].
4.2 Thing speak
Thing Speak is an Internet of Things (IoT) platform that
lets you gather and hold sensor records in the cloud and
develop IoT applications. The Thing Speak IoT platform
delivers apps that let you study and visualize your value.
5. SYSTEM DESIGN
5.1 BLOCK DIAGRAM
Fig-7: Represents the arrangements of components.
5.2 Flow Diagram
Fig -8: Flow diagram.
5.3 Circuit diagram
Fig -9: Circuit diagram.
6. Working procedure
1. The above sensors can sense temperature,
humidity, and smoke.
2. When we will join it to Arduino microcontroller
then it will detect the gases, and it will progress the
Pollution level in PPM (parts per million).
3. Then our project is based on the wireless that is
stored in the cloud database.
4. For that, we have to require some programming
concepts to run the project that's why we have to
create a code using Aurdino1.6.10. Software.
5. In this software, the code should be written in
simple C language with all descriptions of sensors,
and another operating system in which the code

explains how the sensor, Wi-Fi module, LCD, and so
on should be connected.
6. The whole program is dumped into the Arduino
microcontroller.
7. With this Wi-Fi module, 8266 is used for Trans
receiving the data from hotspot from another
device.
8. And it useful for detecting the number of polluted
gases in the air with that the values are displayed in
the cloud.
9. The percentage levels are monitored continuously
in LCD and cloud database also.
10. If the level of gas value more than the threshold
value buzzer starts ON automatically.
7. RESULT AND DISCUSSION
In the pollution monitoring system gas sensor (mq2) isused
to detect the gas likes oxygen, carbon dioxide, nitrogen, and
other toxic gases. The DTH11 sensor is used to detect
temperature and humidity. The concentration of air
pollutants such as CO, Carbon dioxide (CO2), methane,
propane, NO2, and dust are displayedin16X2LCD.When the
limit of sensed value exceeds the threshold value the buzzer
that alerts. The online application needs to analyze air
quality value got from sensors. Thing-speak is an open-
source application programming interface that needs to
store and recover data from interconnected things usingthe
hypertext protocol over the internet or via a local area
network. It also offers access to a wide range of embedded
devices and web facilities.
8. CONCLUSION
The system utilizes city buses, industrial areas to collect
pollutant gases such as CO, smoke, and temperature. Here
we have successfully designed such a system that can
monitor the real-time air pollutionpercentagepresentinthe
air which can be accessed from anywhere in the world so,
here we have designed a circuit which makes takes
corrective action on the increase of air pollution on the
particular threshold value. The proposed Wireless Air
Pollution Monitoring System be responsible for real-time
info about the level of air pollution in these areas, as well as
alerts in cases of extreme change in the quality of air. This
data can then be used by the establishments to take prompt
activities such as leaving people or sending crisisreplyteam.
The system uses city buses to gather pollutant gases such as
CO, NO2, and SO2. The pollution facts from several mobile
sensor ranges are conveyed to a central some that make
these facts accessible on the Internet. The facts display the
pollutant range and their conformance to local air quality.
REFERENCES
1. Navreetinder Kaur1, Rita Mahajan2, Deepak Bagai3, “Air
Quality Monitoring System based on Arduino
Microcontroller”, International Journal of Innovative
Research in Science, Engineering and Technology (An ISO
3297: 2007 Certified Organization)Vol.5,Issue6,June2016,
P.G. Student, Dept. of Electronics and Communication, PEC
University of Technology, Chandigarh, India1 Assistant
Professor, Dept. of Electronics and Communication, PEC
University of Technology, Chandigarh, India2 Professor,
Dept. of Electronics and Communication, PEC University of
Technology, Chandigarh, India3.
2. Kennedy Okokpujie, Etinosa Noma-Osaghae, Odusami
Modupe, Samuel John and Oluga Oluwatosin, “A SMART AIR
POLLUTION MONITORINGSYSTEM”,International Journal of
Civil Engineering and Technology(IJCIET)Volume9,Issue9,
September 2018, pp. 799–809, Article ID: IJCIET_09_09_077
Available online at
http://www.iaeme.com/ijciet/issues.asp?JType=IJCIET&VTy
pe=9&IType=9 ISSN Print: 0976-6308 and ISSN Online:
0976-6316 © IAEME Publication Scopus Indexed,
Department of Electrical and Information Engineering,
Covenant University, Ogun State, Nigeria.
3. Arpan Chakraborty (Roll No 11705514010) Prajukti Das
(Roll No 11705514023) Shovan Karmakar (Roll No
11705514028), Mr. Avishek Paul (AssistantProfessor), “AIR
QUALITY SENSING AND MONITORING”.
4. Harsh N. Shah 1, Zishan Khan 2, Abbas Ali Merchant 3,
Moin Moghal 4, Aamir Shaikh 5, Priti Rane 6, “IOT Based Air
Pollution Monitoring System”, International Journal of
Scientific & Engineering Research Volume 9, Issue 2,
February-2018 ISSN 2229-5518, 1, 2, 3,4,5Student,Diploma
in Computer Engineering, BGIT, Mumbai Central, India
6Assistant Professor, BGIT, Mumbai Central, India.
5. Devahema 1, P.V. Sai Surya Vamsi 2, Archit Garg 3,
Abhinav Anand 4, Desu Rajasekhar Gupta 5,” IOT based Air
Pollution Monitoring System”, Journal of Network
Communications and Emerging Technologies
(JNCET)www.jncet.org Volume 8, Issue 4, April (2018), 1
Assistant Professor, SRM Institute of Science & Technology,
Chennai, Tamil Nadu, India. 2, 3, 4, 5 Student, SRM Institute
of Science & Technology, Chennai, Tamil Nadu, India.
6. https://www.arduino.cc/en/guide/environment
7 .https://www.electronicshub.org/dht11-humidity-
sensor-arduino/

IRJET- Air Pollution Monitoring System using IoT

More Related Content

What's hot (19)

Similar to IRJET- Air Pollution Monitoring System using IoT (20)

More from IRJET Journal (20)

Recently uploaded (20)

IRJET- Air Pollution Monitoring System using IoT