IRJET- Design and Fabrication of a Single-Phase 1KVA Transformer with Automatic Cooling System

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
© 2018, IRJET | Impact Factor value: 6.171 | ISO 9001:2008 Certified Journal | Page 679
Design and fabrication of a Single-phase 1KVA Transformer with
automatic cooling system
Rahul Turkar1, Rahul Shahare2, Prashant Sidam3, Vijay Giradkar4, Avinash Patil5, Priya Sarode6
Department of Electrical Engineering, Nagpur Institute of Technology, Nagpur(441501), India.
-----------------------------------------------------------------------***-------------------------------------------------------------------------------
Abstract: This paper presents a method for the design of shell
type, single phase distribution transformers to obtain the
manufacturing specifications .This transformer have two
output voltages it convert from 230V to 115V and 120V. There
are without providing any tapping on the transformer. Here is
a simple temperature sensor Circuit are use to sensing the
temperature with the help of including temperature sensor,
automatically switch ON and off the dc fan are start and stop
according to the temperature increase and decrease. This
project uses IC LM358 is used as a Voltage Comparator, it
compares two input voltages at pins 2 and 3. The basic
working principle of temperature controlled DC fan is based on
the thermistor and provides protection from overheating of
Transformer. Air blast cooling method is used in transformer.
Key words: Transformer ,Transformer protection,
Temperature sensor
1. INTRODUCTION
The transformer is probably one of the most useful electrical
devices ever invented. It can change the magnitude of
alternating voltage or current from one value to another.
They also have a very high efficiency as high as 99%. When
search for the same during this period then got the
information about winding and maintenance. The
transformer is a static device which is use to transfer
electrical energy from one ac circuit to another ac circuit,
with increase or decrease in voltage/current but without any
change in frequency. Temperature controlled DC fan is a
temperature based fan. It can cool the devices by operating a
DC fan when the temperature in its vicinity increases above
the preset level. Its operation is fully automatic and turns off
when the temperature returns normal.
1.1 Need of Transformer
In most of the cases, appliances are manufactured to work
under some explicit voltage. Transformer is used to adjust
the voltages to a proper level. The transformer is the basic
components for the transmission of the electricity.
Transformer is use to increase the voltage at the power
generating station (step up) and to decrease the voltage (step
down) for house hold persistence. By increasing the voltages
the loss of the electricity in the transmission purpose in
minimalize.
1.2Hardware requirement
 Bobbin
 Winding Machine
 Copper wire
 Stamping( E & I Shape)
 Transformer Clamp
 Resistor (4.7KΩ)
 Op Amp (LM 358)
 Transistor (BC 548)
 9V DC Battery
 5V DC Fan
 NTS Thermistor (4.7kΩ)
 Potentiometer (4.7kΩ)
1.3 THE TRANSFORMER DESIGN PROBLEM
A. Design Considerations and limitations:
In a design, a concept is given shape with the
application of science, technology and invention to
realization of a machine so as to content required
performance and characteristics. A design process is not
merely engineering calculations but involves careful
considerations of the design base, conditions, design transfer
and information updating.
Knowing the characteristics and specifications that a
transformer has to satisfy, the main areas of design include:
• Magnetic circuit; core, window etc.
• The electric circuit; the windings.
• The insulation.
• The mechanical construction.
The designer’s work lies in properly allocating the space to
frame, core, air gap, windings, insulation and cooling circuit
in the transformer. Moreover economy in manufacturing
costs, operating and running costs are also kept in vision.
Limitations are imposed on design because of:-
• Saturation of magnetic parts.
Volume: 05 Issue: 04 | Apr-2018 www.irjet.net p-ISSN: 2395-0072

• Temperature rise under high output.
• Insulation breakdown due to high voltage gradients.
B. Selection Of Design Constants:
The design depends upon power choice of design constants,
flux density (Bm), current density (δ) and window space
factor (KW). Therefore, it is worthwhile to discuss the factors
governing the choice of these coefficients.
If we choose higher value of flux density (Bm), the core area
Ai reduces. This will reduce the diameter of circum-circle
thereby reducing the length of mean turn.
Thus there is saving in the cost of iron and copper. But very
high flux density is not possible, the restriction is because of
iron losses, saturation and magnetizing current. Transformer
should be designed for lower iron losses giving good
efficiency. Therefore, for small transformer comparatively
lower flux density (1.1 to 1.4 Wb/m2) is implicit.
The choice of current density (δ) affects the I2R losses and
also the load at which maximum efficiency occurs. The
allowable values of current density for small power
transformers are taken as (δ =1.5 to 2.6 A/mm2).
The window space factor, Kw has been defined as the ratio of
copper area in the window to the total window area .The
total window area includes the copper area, insulation and
the air gap of coil spaces. The relative amounts of copper and
insulation used will influence the value of Kw. The amount of
copper and insulation used depends upon the KVA capacity
and voltage rating respectively. Thus choice of Kw depends
upon KVA capacity and voltage rating. The following
experimental relation is normally used for estimation of Kw.
C. Dimensions of Shell Type Transformer:
Dimensions of the shell type transformer have been shown in
Figure. For shell type transformer only the central limb is
wound. The central limb in this case carries double flux as
that of outer limbs. Therefore, the central limb will have the
twice area as that of outer limbs.
Figure: Dimensions of Shell Type Transformer
a = width of outer limbs
b =depth of core
2a=width of central limb.
Gross core section of central limb = (2a x b)
Over all width (W) = 2Ww + 4a
Overall height (H) = hw + 2hy = hw + 2a
2. DESIGN OF TRANSFORMER
In this section, design for the construction of single phase
shell type tapped transformer has been presented. The
design of core and the windings has been discussed. Core
design includes the window height, window width and the
outer and central limbs. Winding design includes the area of
cross section and number of turns of primary and secondary
side.
 Specifications:
The designed transformer is of 1 KVA, 230 V/120 Volts, 50
Hz, Single phase, Shell type, tapped transformer. Design and
fabrication of this transformer has been made possible by the
special calculations and design procedure.
 Core Design:
The core section for shell type transformer is always being of
rectangular shape. The design of the core is presented by the
following procedure. Design constants in this design
procedure are certain as for the small transformers.
Voltage per turn = Vt = K ×Q (volts)
Q = KVA rating of transformer
K = Output constant of transformer
Turns per volt (Te) for a transformer is given as:
Te= 1/4.44×f× Bm×Ai
Ai= Net Iron Area of Core
Ai =1/4.44×Bm ×Te
Te = 2 Turns/ V,
Flux density = Bm = 1.55 web/m2 , f =Supply frequency = 50
Hz
Agi = Gross Iron Area of Core
Agi = Ai/Ks
∴Ks = stacking factor = 0.9
a = 0.85×√

b = 0.53×√
where;
a = Height of outer limb
b = Depth of yoke (core)
 Yoke Design:
To minimize the iron losses of the yoke, area of yoke is fixed
to be 2 times the core area:
Ay = (1.2)× Ai
Yoke flux density =By = Øm/Ay
Øm = Bm ×Ai
Yoke area (net) = yoke area (gross)×Ks
Ks =stacking factor
For rectangular yoke section:
Yoke depth = Dy = a
Yoke height = Hy= yoke area (gross)/Dy
 Window Design:
KVA of single phase shell type transformer is given as :
S = 2.22×f × Bm × Ai ×Aw ×Kw× ×10-3
Aw = S/2.22×f × Bm × Ai ×Kw× ×10-3
Where,
Aw= Area of window in cm2
f = frequency in Hz
Bm = Flux density in web/m2
Kw = window factor =10/30+KV
= current density in A/mm2
Ai = Net Iron Area of Core
Aw = ww ×hw
3 = hw / ww
Ww = Window Width, hw = Window height
 Overall Frame Design:
Overall Width of frame=W = [(2×ww) +(4×a)]cm
Overall height of frame= H = [hw +(2×hy )]cm
Window height =hy =a
 Windings Design:
Primary winding:
Primary winding current I1 = (S/V) Ampere
a1 = [(I1/ ) +LC]mm2
a1 =Cross - section of primary winding
= current density in A/mm2
L.C = Lamination coating =0.005mm2
Number of turns:
No. of secondary turns =N2 = V2 ×Te
No. of primary turns =N1 = V1 ×Te
N1=Primary turns , N2=Secondary turns
Secondary winding :
Secondary winding has been designed with same conductor
as with the primary winding.
Cross - section of secondary winding=a2=a1
For windings, SWG 20 conductor has been used with
diameter =d
3. BLOCK DIAGRAM
Fig. Block Diagram
3.1 CONSTRUCTION
The core is made of silicon steel which has little
hysteresis loss and high permeability. Further core is
laminated in order to reduce eddy current. The simple
element of a Transformer consist of two coils having mutual
inductance and a laminated steel core. The two coil are

insulated from each other and the steel core. The primary
and secondary winding is not physically connected, but
magnetically linked to each other. The eddy current loss is
minimized by laminating the core, the laminations being
insulated from each other by dainty coat of core plate varnish
or oxide layer on the surface. The silicon steel laminated to
‘E’ and ‘I’ stamping due to the more number. The single phase
transformer have used in solo winding. Which are connected
to AC source is known as primary winding and other winding
is connected to load as soon as secondary winding. The
primary winding is wound to centre limb to E stamping core
and these winding laminated by insulating coil .and the
insulating paper also wound to primary winding an the
secondary winding is wound to over the primary winding.
The primary winding and secondary winding is not
electrically connected but are magnetically connected and
the flux is produce by core of transformer.
4. METHODOLOGY
The transformer mechanism on principal is mutual
induction. A transformer is a static device, which is transfer
electric power from one circuit to another circuit without any
variation in frequency. It can rise or lower the voltage in
circuit but with a corresponding increase or decrease
current. The circuit link by common magnetic flux in its
simplest form, it consists of two inductive coils which are
electrically separated but magnetically linked through a path
of low reluctance. The ac supply is connected to the primary
winding, an alternating flux is step up in laminated core,
most of which is linked with the other oil in which it
produces mutually induced EMF If the second coil circuit is
close a current flow in intended so electric energy transfer
from the first coil into second coil. The first coil connected to
electrical supply is known as primary winding and load are
connected to secondary winding. A transformers are often
used to step down voltages in the 115-120 V range and
voltages in the 230V range - for example, providing 115 V or
120 V (with taps) from 230 V input, allowing equipment
designed for 115 or 120 V to be used with a 230 V supply
5. RESULT AND DISCUSSION:
This section describes the results of our testing and shows
that tests are performed .This section discuss the result of
losses of transformer and protected against the heating of
transformer.
By implementing our project the following results were
obtained:
For residential we are getting a supply of 230V and through
step down transformer we are converting it into 115V and
120V.
6. CONCLUSION:
Transformer is the most significant component of power
system. A good design for efficiency increase is a challenge in
the fabrication of a transformer. Lesser efficient transformers
are poorly designed because the losses occurring in a
transformer are more likely considered the design flow.
Transformers can be made maximum efficient if fabricated
using the precise dimensions. The construction of this
1000Watts (1KVA), 220Volts transformer at a 50Hz
frequency was a gradual process from gathering of materials
to testing of components. In this project, we came to
conclusion that the use of transformer for short circuit and
open circuit test overall construction of transformer and
winding regular. We learn process of troubleshooting of this
transformer. We get information and knowledge about
connections of this transformer. This project is a low cost,
reliable, effective, protective and efficient. This project gives
us to learn about good things and lot of knowledge of
protection methods.
7. REFERENCES
1. Martin J. Heathcote. 1988. J and P Transformer book.
Oxford university press.
2. Say M.G. 2005. Performance and Design of AC
Machines, CBS publishers India..
3. P. Gill, “Electrical Power Equipment Maintenance
and Testing”, 2nd edition., CRC Press, Taylor &
Francis Group. 2009.
4. Stephen J. Chapman, “Electrical Machinary
Fundamentals”, BAE SYSTEMS Austrailia.
5. Sawhney A.K. 2006. Electrical Machine Design,
Dhanapat Rai publishers, India.
6. R.K. Agarwal, “Principles of Electrical Machine
Design”, S. K. Kataria & Sons, 2009.

IRJET- Design and Fabrication of a Single-Phase 1KVA Transformer with Automatic Cooling System

More Related Content

What's hot (19)

Similar to IRJET- Design and Fabrication of a Single-Phase 1KVA Transformer with Automatic Cooling System (20)

More from IRJET Journal (20)

Recently uploaded (20)

IRJET- Design and Fabrication of a Single-Phase 1KVA Transformer with Automatic Cooling System