IRJET- Efficiency Variation of Solar Panel using PV Technology

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 06 Issue: 05 | May 2019 www.irjet.net p-ISSN: 2395-0072
© 2019, IRJET | Impact Factor value: 7.211 | ISO 9001:2008 Certified Journal | Page 6229
“Efficiency Variation of Solar Panel using PV Technology”
Samiksha Dhakate1, Pooja Hirudkar2, Rohit Kapgate3, Rupesh. S. Jadhav4
1,2,3Student of School of Mechanical and Civil Engineering, MIT Academy of Engineering, Alandi(D), Pune
4Assistant Professor of School of Mechanical and Civil Engineering, MIT Academy of Engineering, Alandi(D), Pune
----------------------------------------------------------------------------***--------------------------------------------------------------------------
Abstract – Photovoltaic solar cell generates electricity by
receiving solar irradiance. The temperature of photovoltaic
modules increases when it absorbs solar radiation, causing a
decrease in efficiency. This undesirable effect can be
partially avoided by applying a heat recovery unit with fluid
circulation with the photovoltaic module. Such unit is called
photovoltaic/thermal collector (PV/T) or hybrid (PV/T). The
objective of the present work is to design a system for
cooling .The solar cell in order to increase its electrical
efficiency and also to extract the heat energy.
Here we designed a setup in which array of water tube is
fitted to back of solar panel to reduce its temperature and
bring temperature to normal operating point. Before this we
checked the solar panel under normal operating condition.
After getting result for various model we compared our back
water cooling tube array results with the ordinary solar
panel.
1. INTRODUCTION
We got motivated from the literature stuff we studied.
Earlier we did not know the concept of efficiency variation
with temperature change of solar panel but after getting
guidance of our project guide and other professor and
after going through research paper we got a idea that we
can apply our engineering knowledge to the problem.
Keeping in mind the energy crisis the world is facing and
the sustainable energy need and its generation, we realize
that we are not completely utilizing/converting the
energy.To keep the panel temperature in control such that
the panel efficiency we will get will be maximum. To
generate the maximum output (voltage production) at any
varying temperature. Utilization of the heated water from
copper pipe for sterilization of medical instruments and
washing purpose.
2. Problem statement
The heat accumulation increases in solar panels thus
decreasing its efficiency of producing voltage and affecting
total voltage production, thus we need to develop cooling
mechanism for solar panel to keep its efficiency maximum.
3. LITERATURE SURVEY
Different research and studies were carried out in
increasing the efficiency of solar panel by using different
techniques. Krauter identified and suggested a technique
of reducing reflection to cool the PV by replacing the front
glass layer with a thin layer of 1 mm running directly over
the PV panel face. As a result, the temperature of PV panel
reduced to 22° C. The main drawback of this technique is
the non-homogeneous thickness of the water flowing over
the surface of the panel which is necessary to improve the
performance level of the technique.
Hosseini studied and indentified a technique that the
temperature of the solar panel can be reduced by spraying
the water over the surface of the panel continuously. The
main drawback of this technique is the researcher does not
take into account the pump power that they were able to
achieve an increase in the electrical system performance
by 17% from 8 am to 5 pm in summer.
After readjusting the water pump and providing the
continuous flow over the surface of the panel they
improved their output.
Dorobantu and Popescu obtain the electricity of about
9.5% by cooling the surface of the solar panel by using thin
film layer of water on the surface of water and hence
obtain better efficiency due to decreasing the losses due to
reflection.
Moharram also implemented the same water sprey
technique to improve the efficiency of the system. They
calculated the maximum allowable temperature to be
45°.They also observed that for operating this technique
for 5 min and decrease the temperature by 10°
4. SYSTEM DESIGN
4.1HARDWARE REQUIREMENTS
4.1.1Mechanical
Sr.No Components Dimension
1. Solar Panel 30*35*2 cm
2. Copper tube Dia(6mm) ,

Thick(1mm)
3. Container 30*30*5 cm
4. Sump 30*15*15 cm
Table. No 4.1.1
4.1.2 Electrical
Sr.No Components Dimension
1. Multi meter Digital
2. Temperature
sensor
Thermocouple
Table. No 4.1.2
4.2 SOFTWARE REQUIREMENT
Sr.No Software Specification
1. Excel Microsoft Excel
2007
2. CATIA V5
Table. No 4.2.1
5. MECHANICAL DESIGN
Fig. No 5.1Back view of solar panel
Fig. No 5.2 Front view of solar panel
6. CIRCUIT DIAGRAM
7. Calculations
Solar panel specification:
1. Rated power( Pmax) =10 ± 3%
2. Open circuit voltage (Voc ) = 21.5V
3. Short circuit current (Isc ) = 0.67 A
4. Voltage at maximum power (Vmp) = 17.7A
5. Current at Maximum Power (Imps) = 0.57 A
6. Maximum system voltage = 600A

7.1 Formulas
𝐴𝐴=A(𝑑𝑖𝑠ℎ)×cos{43.33−𝛿/2}
𝛿=23.45{360/365×(284+𝑛)}
Where;
AA=Aperture Area
A (dish)=Area of dish
n: Number of days of year 𝜂=𝑃(𝑜𝑢𝑡)ℎ𝑒𝑎𝑡𝑖𝑛𝑝𝑢𝑡
Heat input= AA×𝑠𝑜𝑙𝑎𝑟𝑖𝑟𝑟𝑎𝑑𝑖𝑎𝑛𝑐𝑒
For 1st day; 𝛿=23.45{360/365× (284+105)}
𝛿=9.4145
Area of dish=30x35cm=0.1050 m2
𝐴𝐴=0.1050×cos {43.33−9.41492}
𝐴𝐴=0.100461 m2
𝜂=𝑃(𝑜𝑢𝑡)/ℎ𝑒𝑎𝑡 𝑖𝑛𝑝𝑢𝑡
𝜂=10 𝑊𝑎𝑡𝑡𝐴𝐴 ×𝑆𝑜𝑙𝑎𝑟 𝑖𝑟𝑟𝑎𝑑𝑖𝑎𝑛𝑐𝑒
𝜂max =10309.6108×0.100461
𝜂max =10/31.10381
𝜂max=0.32154
8. IMPLEMENTATION DETAILS
Firstly the solar panel is tested without the cooling system
(PV Technology) and then the voltage variation of solar
panel with temperature variation is being measured by
using Multi meter. A working experimental setup is
developed to determine how long it takes to cool down the
module based on proposed cooling system. The water
circulation tank use natural convection to circulate water.
An experimental validation of hat rate model and cooling
rate model has been done. Based on heating and cooling
rate model it is found that the PV panel yields the highest
output energy if cooling of the module starts. The work
done in this project proposes modeling of photovoltaic
model in which temperature and sun’s irradiance, of the
PV array is taken into account. To check the correctness of
the solar PV model predicted values of solar radiation data
are compared with calculated weekly values. The
radiation effect of solar radiation on the tilted surfaces and
vertical surfaces for different orientations from horizontal,
have also been calculated. The calculated values and
results are found to be very close agreement with
measured values. The method presented in this project can
be used to do approximation hourly, global, diffuse solar
radiation on inclined and vertical surfaces and horizontal
surfaces and at different angles with greater accuracy for
any location.
This tells us the power generation capacity rated of power
plant with the actual power generation capacity of the
plant.
9. RESULTS
Month Temperature
January 25
February 26
March 28
April 29
May 30
June 29
July 28
August 28
September 29
October 29
November 28
December 27
This graph is plotted between two parameters
temperature v/s the month.
Irradiance
(W/m^2)1
Temperature
(° C)
O/P DC
Voltage (V)
1000 25 18.9
1000 27.5 17
1000 30 17
1000 32.5 18
1000 35 18.3
1000 37.5 18
22
24
26
28
30
32
Temperature

1000 40 17.6
1000 42.5 17
1000 45 17.2
Power Voltage Temperature
10 18.9 25
10 17 27.5
10 17 30
10 18 32.5
10 18.3 35
10 18 37.5
10 17.6 40
10 17 42.5
10 17.2 45
Time Temperature Voltage Power Current
11:15 25 18.9 29.076 0.65
11:30 27.5 17 26.153 0.65
11:45 30 17 26.153 0.65
12:00 32.5 18 27.69 0.65
12:15 35 18.3 28.153 0.65
12:30 37.5 18 27.692 0.65
12:45 40 17.6 27.076 0.65
1:00 42.5 17 26.15 0.65
1:15 45 17.2 26.45 0.65
10. CONCLUSION AND FUTURE SCOPE
This project can be use by Solar power operated
Companies to improve their power efficiency. By hospitals
to utilize the heated water through cooling pipe for
sterilization purpose. Environmental authorities to
decrease the low efficient renewable source utilization. By
every customer who make use of solar panel for power
production.
11. REFERENCES
[1]https://www.sciencedirect.com/science/article/pii/S2
090447913000403
[2]https://www.researchgate.net/publication/304785444
_Photovoltaic_panels_A_review_of_the_cooling_techniques
[3]https://hrcak.srce.hr/file/234790
[4]https://www.ijert.org/research/efficiency-
improvement-of-photovoltaic-panels-by-design-
improvement-of-cooling-system-using-back-water-
cooling-tubes-IJERTV7IS010057.pdf
[5]https://www.tandfonline.com/doi/abs/10.1080/0145
7630802529214
16.5
17
17.5
18
18.5
19
0 10 20 30 40 50
O/P DC Voltage (V)
16.5
17
17.5
18
18.5
19
19.5
0 10 20 30 40 50
Voltage vs Temperature
25
27.5
30
32.5
35
37.5
40
42.5
4518.9 17
17
18
18.3 18 17.6 17
17.2
29.076
26.153
26.153
27.69
28.15327.69227.07626.15
26.45
0.65
0.65 0.65
0.65
0.65
0.65
0.65
0.650.65
0
10
20
30
40
50
60
70
80
90
100
11:15 11:30 11:45 12:00 12:15 12:30 12:45 1:00 1:15
Temperature Voltage

IRJET- Efficiency Variation of Solar Panel using PV Technology

More Related Content

What's hot (20)

Similar to IRJET- Efficiency Variation of Solar Panel using PV Technology (20)

More from IRJET Journal (20)

Recently uploaded (20)

IRJET- Efficiency Variation of Solar Panel using PV Technology