Itn instructor ppt_chapter6_network_layer

© 2008 Cisco Systems, Inc. All rights reserved. Cisco ConfidentialPresentation_ID 1
Chapter 6:
Network Layer
Introduction to Networks

Presentation_ID 2© 2008 Cisco Systems, Inc. All rights reserved. Cisco Confidential
Chapter 6: Objectives
Students will be able to:
 Explain how network layer protocols and services
support communications across data networks.
 Explain how routers enable end-to-end connectivity in a
small to medium-sized business network.
 Determine the appropriate device to route traffic in a
small to medium-sized business network.
 Configure a router with basic configurations.

Chapter 6
6.1 Network Layer Protocols
6.2 Routing
6.3 Routers
6.4 Configuring a Cisco Router
6.5 Summary

Network Layer
Network Layer

Network Layer Protocols
Network Layer in Communication

The Network Layer
End to End Transport processes
 Addressing end devices
 Encapsulation
 Routing
 De-encapsulating

Network Layer Protocols
Common Network Layer Protocols
 Internet Protocol version 4 (IPv4)
 Internet Protocol version 6 (IPv6)
Legacy Network Layer Protocols
 Novell Internetwork Packet Exchange (IPX)
 AppleTalk
 Connectionless Network Service (CLNS/DECNet)

Characteristics of the IP protocol
Characteristics of IP

IP - Connectionless

IP – Best Effort Delivery

IP – Media Independent

IPv4 Packet
Encapsulating IP

IPv4 Packet
IPv4 Packet Header
Version, Differentiated Services (DS), Time-to-Live
(TTL),Protocol, Source IP Address, Destination IP Address
Version
IP Header
Length
Differentiated Services
Total Length
DSCP ECN
Identification Flag Fragment Offset
Time To Live Protocol Header Checksum
Source IP Address
Destination IP Address
Options (optional)
Padding
Byte 1 Byte 2 Byte 3 Byte 4

IPv4 Packet
IPv4 Header Fields
Internet Header Length (IHL), Total Length, Header Checksum,
Identification, Flags, Fragment Offset
Version
IP Header
Length
Differentiated Services
Total Length
DSCP ECN
Identification Flag Fragment Offset
Time To Live Protocol Header Checksum
Source IP Address
Options (optional)
Padding

IPv4 Packet
Sample IPv4 Headers

Limitations of IPv4
 IP Address depletion
 Internet routing table expansion
 Lack of end-to-end connectivity

Introducing IPv6
 Increased address space
 Improved packet handling
 Eliminates the need for NAT
 Integrated security
 4 billion IPv4 addresses
4,000,000,000
 340 undecillion IPv6 addresses
340,000,000,000,000,000,000,000,000,000,000,000,000

IPv6 Packet
Encapsulating IPv6

IPv6 Packet
IPv6 Packet Header
Version Traffic Class Flow Label
Payload Length
Next
Header
Hop Limit
Source IP Address

IPv6 Packet
Sample IPv6 Header

Routing
Host Routing Tables

Host Routing Tables
Host Packet Forwarding Decision

Host Routing Tables
Default Gateway
Hosts must maintain their own, local, routing table to ensure
that network layer packets are directed to the correct
destination network. The local table of the host typically
contains:
 Direct connection
 Local network route
 Local default route
R

Host Routing Tables
IPv4 Host Routing Table

Host Routing Tables
Sample IPv4 Host Routing Table

Host Routing Tables
Sample IPv6 Host Routing Table

Router Routing Tables
Router Packet Forwarding Decision

IPv4 Router Routing Table
R1#show ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
D 10.1.1.0/24 [90/2170112] via 209.165.200.226, 00:00:05, Serial0/0/0
D 10.1.2.0/24 [90/2170112] via 209.165.200.226, 00:00:05, Serial0/0/0
C 192.168.10.0/24 is directly connected, GigabitEthernet0/0
L 192.168.10.1/32 is directly connected, GigabitEthernet0/0
C 209.165.200.224/30 is directly connected, Serial0/0/0
L 209.165.200.225/32 is directly connected, Serial0/0/0
R1#
192.168.10.0/24
R2
192.168.11.0/24
10.1.1.0/24
10.1.2.0/24
209.165.200.224 /30
.226
.10
.10
.10
.10
.1
.1.1
G0/1
.225
S0/0/0
G0/0
.1
R1
PC1
PC2

Directly Connected Routing Table Entries
A B C
A Identifies how the network was learned by the router.
B Identifies the destination network and how it is connected.
C Identifies the interface on the router connected to the destination network.
192.168.10.0/24
R2
192.168.11.0/24
10.1.1.0/24
10.1.2.0/24
209.165.200.224 /30
.226
.10
.10
.10
.10
.1
.1
64.100.0.1
.1
G0/1
.225
S0/0/0
G0/0
.1
R1
PC1
PC2

Remote Network Routing Table Entries
D 10.1.1.0/24 [90/2170112] via 209.165.200.226, 00:00:05, Serial0/0/0
A Identifies how the network was learned by the router.
B Identifies the destination network.
C Identifies the administrative distance (trustworthiness) of the route source.
D Identifies the metric to reach the remote network.
E Identifies the next hop IP address to reach the remote network.
F Identifies the amount of elapsed time since the network was discovered.
G Identifies the outgoing interface on the router to reach the destination network.
192.168.10.0/24
R2
192.168.11.0/24
10.1.1.0/24
10.1.2.0/24
209.165.200.224 /30
.226
.10
.10
.10
.10
.1
.1
64.100.0.1
.1
G0/1
.225
S0/0/0
G0/0
.1
R1
PC1
PC2

Next-Hop Address
192.168.10.0/24
R2
192.168.11.0/24
10.1.1.0/24
10.1.2.0/24
209.165.200.224 /30
.226
.10
.10
.10
.10
.1
.1
64.100.0.1
.1
G0/1
.225
S0/0/0
G0/0
.1
R1
PC1
PC2
R1#show ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
D 10.1.1.0/24 [90/2170112] via 209.165.200.226, 00:00:05, Serial0/0/0
D 10.1.2.0/24 [90/2170112] via 209.165.200.226, 00:00:05, Serial0/0/0
C 209.165.200.224/30 is directly connected, Serial0/0/0
L 209.165.200.225/32 is directly connected, Serial0/0/0
R1#

Routers
Anatomy of a Router

Anatomy of a Router
A Router is a Computer

Anatomy of a Router
Router CPU and OS

Anatomy of a Router
Router Memory
Memory
Volatile /
Non-Volatile
Stores
RAM Volatile
• Running IOS
• Running configuration file
• IP routing and ARP tables
• Packet buffer
ROM Non-Volatile
• Bootup instructions
• Basic diagnostic software
• Limited IOS
NVRAM Non-Volatile • Startup configuration file
Flash Non-Volatile
• IOS
• Other system files

Anatomy of a Router
Inside a Router

Anatomy of a Router
Router Backplane
Two 4 GB flash card slots
Double-wide eHWIC slots eHWIC 0 AUX
port
LAN
interfaces
USB
Ports
Console
USB Type B
Console
RJ45

Anatomy of a Router
Connecting to a Router
WAN
Interface
AUX
port
LAN
interfaces
Console
USB Type B
Console
RJ45

Anatomy of a Router
LAN and WAN Interfaces
Serial interfaces
LAN interfaces

Router Boot-up
Cisco IOS

Router Boot-up
Bootset Files

Router Boot-up
Router Bootup Process
System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
<output omitted>
1.Perform the POST
and load the
bootstrap program
2.Locate and load the
Cisco IOS software
3.Locate and load the
startup configuration
file or enter setup
mode

Router Boot-up
Show Versions Output
Router# show version
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.2(4)M1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Thu 26-Jul-12 19:34 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
Router uptime is 10 hours, 9 minutes
System returned to ROM by power-on
System image file is "flash0:c1900-universalk9-mz.SPA.152-4.M1.bin"
Last reload type: Normal Reload
Last reload reason: power-on
<Output omitted>
Cisco CISCO1941/K9 (revision 1.0) with 446464K/77824K bytes of memory.
Processor board ID FTX1636848Z
2 Gigabit Ethernet interfaces
2 Serial(sync/async) interfaces
1 terminal line
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
<Output omitted>
Technology Package License Information for Module:'c1900'
-----------------------------------------------------------------
Technology Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------
ipbase ipbasek9 Permanent ipbasek9
security None None None
data None None None
Configuration register is 0x2142 (will be 0x2102 at next reload)
Router#

Network Layer
Configuring a Cisco Router

Configure Initial Settings
Router Configuration Steps
Router> enable
Router# configure terminal
Enter configuration commands, one per line.
End with CNTL/Z.
Router(config)# hostname R1
R1(config)#
192.168.10.0/24
R2
192.168.11.0/24
10.1.1.0/24
10.1.2.0/24
209.165.200.224 /30
.226
.10
.10
.10
.10
.1
.1.1
G0/1
.225
S0/0/0
G0/0
.1
R1
PC1
PC2
Router> en
Router# conf t
Enter configuration commands, one per line.
End with CNTL/Z.
Router(config)# ho R1
R2(config)#
OR
R1(config)# enable secret class
R1(config)#
R1(config)# line console 0
R1(config-line)# password cisco
R1(config-line)# login
R1(config-line)# exit
R1(config)#
R1(config)# line vty 0 4
R1(config-line)# password cisco
R1(config-line)# login
R1(config-line)# exit
R1(config)#
R1(config)# service password-encryption
R1(config)#
R1(config)# banner motd #
Enter TEXT message. End with the character '#'.
***********************************************
WARNING: Unauthorized access is prohibited!
***********************************************
#
R1(config)#
R1# copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
R1#

Configure Interfaces
Configure LAN Interfaces
192.168.10.0/24
R2
192.168.11.0/24
10.1.1.0/24
10.1.2.0/24
209.165.200.224 /30
.226
.10
.10
.10
.10
.1
.1.1
G0/1
.225
S0/0/0
G0/0
.1
R1
PC1
PC2
R1# conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#
R1(config)# interface gigabitethernet 0/0
R1(config-if)# ip address 192.168.10.1 255.255.255.0
R1(config-if)# description Link to LAN-10
R1(config-if)# no shutdown
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0,
changed state to up
R1(config-if)# exit
R1(config)#
R1(config)# int g0/1
R1(config-if)# ip add 192.168.11.1 255.255.255.0
R1(config-if)# des Link to LAN-11
R1(config-if)# no shut
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1,
changed state to up
R1(config-if)# exit
R1(config)#

Configure Interfaces
Verify Interface Configuration
192.168.10.0/24
R2
192.168.11.0/24
10.1.1.0/24
10.1.2.0/24
209.165.200.224 /30
.226
.10
.10
.10
.10
.1
.1.1
G0/1
.225
S0/0/0
G0/0
.1
R1
PC1
PC2
R1# show ip interface brief
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0 192.168.10.1 YES manual up up
GigabitEthernet0/1 192.168.11.1 YES manual up up
Serial0/0/0 209.165.200.225 YES manual up up
Serial0/0/1 unassigned YES NVRAM administratively down down
Vlan1 unassigned YES NVRAM administratively down down
R1#
R1# ping 209.165.200.226
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 209.165.200.226, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/9 ms
R1#

Configuring a Cisco Router
Configuring the Default Gateway

Default Gateway on a Host
192.168.10.0/24
192.168.11.0/24
G0/1
.1
.1
G0/0
R1
.10
PC1
.10
PC2
.10
PC4
.10
PC3
192.168.10.0/24
192.168.11.0/24
G0/1
.1
.1
G0/0
R1
.10
PC1
.11
PC2
.11
PC4
.10
PC3

Default Gateway on a Switch
192.168.11.0/24
.1
G0/1
.1
G0/0 R1
192.168.10.0/24
.10
PC1
.11
PC2
S1#show running-config
Building configuration...
!
<output omitted>
service password-encryption
!
hostname S1
!
Interface Vlan1
ip address 192.168.10.50
!
ip default-gateway 192.168.10.1
<output omitted>
S1 S2
.50
If the default gateway were not configured on S1, response
packets from S1 would not be able to reach the
administrator at 192.168.11.10. The administrator would not
be able to mange the device remotely.

Network Layer
Summary
In this chapter, you learned:
 The network layer, or OSI Layer 3, provides services to allow
end devices to exchange data across the network.
 The network layer uses four basic processes: IP addressing
for end devices, encapsulation, routing, and de-
encapsulation.
 The Internet is largely based on IPv4, which is still the most
widely-used network layer protocol.
 An IPv4 packet contains the IP header and the payload.
 The IPv6 simplified header offers several advantages over
IPv4, including better routing efficiency, simplified extension
headers, and capability for per-flow processing.

Network Layer
Summary
 In addition to hierarchical addressing, the network layer is
also responsible for routing.
 Hosts require a local routing table to ensure that packets are
directed to the correct destination network.
 The local default route is the route to the default gateway.
 The default gateway is the IP address of a router interface
connected to the local network.
 When a router, such as the default gateway, receives a
packet, it examines the destination IP address to determine
the destination network.

Network Layer
Summary
 The routing table of a router stores information about directly-
connected routes and remote routes to IP networks. If the
router has an entry in its routing table for the destination
network, the router forwards the packet. If no routing entry
exists, the router may forward the packet to its own default
route, if one is configured, or it will drop the packet.
 Routing table entries can be configured manually on each
router to provide static routing or the routers may
communicate route information dynamically between each
other using a routing protocol.
 In order for routers to be reachable, the router interface must
be configured.

Itn instructor ppt_chapter6_network_layer

More Related Content

What's hot (18)

Similar to Itn instructor ppt_chapter6_network_layer (20)

More from Universitas Teknokrat Indonesia (6)

Recently uploaded (20)

Itn instructor ppt_chapter6_network_layer