L012627682

IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE)
e-ISSN: 2278-1684,p-ISSN: 2320-334X, Volume 12, Issue 6 Ver. II (Nov. - Dec. 2015), PP 76-82
www.iosrjournals.org
DOI: 10.9790/1684-12627682 www.iosrjournals.org 76 | Page
A Review on Design Process of Orthopedic Implants
Vipul V.Ruiwale1
, Dr.R.U.Sambhe2
1
(Mechanical Engineering Department, MIT College of Engineering, Pune, Maharashtra, India)
2
(Mechanical Engineering Department, JRD Institute of Engineering and Technology, Yavatmal, Maharashtra,
India)
Abstract : The design process for medical devices is highly regulated to ensure the safety of patients. This
paper will present a review of the design process for implantable orthopedic medical devices. It will cover the
main stages of feasibility, design reviews, design, design verification, manufacture, design validation, design
transfer and design changes.
Keywords:– 3D Printing, Design, Implant, Medical device, Orthopedic,
I. Introduction
The design process for medical devices is highly regulated to ensure the safety of patients and
healthcare workers. The Medical Device Directive [1] was developed to regulate medical devices in Europe. It
is a document that is legally binding, enforceable in law and with penalties for non-compliance. Regulations
outside Europe vary. For example, in the United States of America, the Food and Drug Administration (FDA) is
responsible for the safety of medical devices [2] and DST is responsible in India. In order to comply with the
regulations, companies are required to have a quality management system in place [3-5] to ensure that the whole
design process is managed and planned in a systematic and repeatable manner. To comply with the regulatory
aspects it is required to maintain a Design History File (which can also be know as a Technical File or Design
Dossier) which describes the design history of a product and is maintained after product is released to include
subsequent changes to the product and relevant post-market surveillance data. The aim of this paper is to give an
overview of the design process for implantable orthopedic medical devices.
II. Design Process
2.1. Overview
The medical implant process, as with other design processes, can be broadly divided into six areas [6-9]:
1. Market
2. Design specification
3. Concept design
4. Detail design
5. Manufacture
6. Sell
However, in this paper a more detailed structure to the design process is discussed, shown in Fig. (1). Each of
these points of the design process are discussed here.
2.2. Feasibility
2.2.1. Design Inputs
Ideas for new or improved or patient specific medical implants will come from surgeons, other
clinicians, sales teams or medical engineers, probably working together as an interdisciplinary team. A surgical
review panel may be formed to help guide the design and ensure that the implant functions correctly surgically.
2.2.2. Commercial Aspects
A feasibility study for a new idea for patient specific implants and to reduce the lead time to
manufacture implant needs to be undertaken to identify the potential market share, similar implants produced by
competitor companies. A review of the intellectual property is also required to determine whether the design can
be protected.

A Review on Design Process of Orthopedic Implant
2.2.3. Planning
It is important that each aspect of the design process is project managed with achievable task set and
defined throughout the project life cycle. The setting of task should enable the project manager to assess the
progress of the project to make sure that it is completed on time and within budget. The definition of the task
should detail the requirements for the project to achieve the objective, for example completing the market
feasibility report and the project objectives. The project plan should include regular tasks and project meetings
to assist with the identification of problems and allow early action to be taken to counteract delays to a project.
The planning process should also include a risk management plan, which should highlight the relevant strategies
that will be employed to reduce and manage the risks that are associated with a project. The planning process
should identify the human and financial resources required to successfully realize a design.
Fig.1 Design Process of Medical Implant [43]

2.2.4. Regulatory Requirements
All medical devices must have regulatory approval before they can be released to market. There are a
number of internationally and nationally agreed requirements to which medical devices must conform. Currently
these standards are not harmonized, and there are differences between those that regulate India, Europe and the
United States. Medical devices must also be classified according to the level of risk associated with their use
upon a patient and to the user. The classification process of a medical device will determine the relevant
approval route to market. It is therefore essential that the regulations that will influence the design of a product
are identified early in the design process. Independent advice on this area must be sought from a Regulatory
Authority, Conformity Assessment Body or other authorised third party.
In the design of the product it is necessary to identify global standards, which apply to all medical
devices, semi-global standards which apply to a particular family of devices and specific standards that apply to
particular devices or pieces of equipment. By identifying these standards complications in the latter stages of the
design process can be avoided. Not all of the standards are mandatory, compliance will often help to accelerate
the approval process.
2.2.5. Design Requirements
The design requirements (or product design specification) are essential before a medical device can be
designed. It sets out exactly what is required of the design against which each stage of the design can be
verified. Whilst the initiation of the project will highlight some of the technical requirements for a project, it is
important to perform a thorough requirement capture process to ensure that all of the functional performance
needs are identified early in the design process. It is important to remember that the requirements are solution
independent to prevent narrowing the design options available. A general standard exists to help determine the
design requirements [10]. Many types of medical device also have particular requirements. In addition, specific
requirements can be specified for certain devices, such as joint replacement implants for the hip and knee
[11,12].
The design requirements for the implant will include:
• intended performance
• design attributes
• materials
• design evaluation
• manufacture
• testing
• instruments required
• sterilization
• packaging
• information to be supplied by the manufacturer [7,14]
For a total knee arthroplasty the important requirements would be for the implant to last for 25 years,
have the required range of motion, prevent loosening and minimize wear debris [19]. In the design of a new
wrist arthroplasty it would be important to consider the range of motion (flexion/extension, radial/ulnar
deviation or radio-carpal rotation), fixation and materials [20]. For the design of an intramedullary nail
stabilizing the bone while the fracture heals would be an important requirement [21].
2.3. Design Reviews
A design review is required, at each stage of the design process, to formally document comprehensive,
systematic examination of a design to:
• evaluate design requirements
• assess capability of the design
• identify problems [13]
2.4. Design
2.4.1. Concept Design
The concept, or conceptual, design stage is where solutions are generated to meet the design
requirements. The aim is to generate as many ideas as possible. At this stage ideas should not be judged.
Various methods exist to help with creativity in developing concept designs such as Brain storming [22-24] and
TRIZ (Theory of Inventive Problem Solving) [22]. Concept design may involve:

• simple sketches of ideas;
• computer aided design models;
• analytical calculations;
• initial manufacturer consultation.
Once a range of concept designs have been developed it is worth assessing each of the concept designs
for patentable technology to ensure that the final design has been fully protected. The protection of ideas and
concepts can play an important role in the success of a product once launched to the market. It is therefore
essential to consider this as early as possible in the design phase. The range of concept designs can then be
systematically rated by the design team to determine the most suitable concept to develop, in the detail design
stage.
2.4.2. Detail Design
At the detail design stage the flesh is put onto the bones of the chosen conceptual idea [7]. A concept design is
worked through until a detail design has been produced. This will include:
• generation of solid computer aided design models
• specification of materials
• drafting of engineering drawings
• analysis of tolerance stacks within associated assemblies to ensure correct operation
• detailing with the inspection requirements to ensure that the part/assembly operates correctly
• liaison with manufacturers to ensure that the device is designed for manufacture (DFM), designed for
assembly (DFA) or designed for manufacture and assembly (DFMA)
2.5. Design Verification
2.5.1. Introduction
Design verification involves confirmation by examination that a medical implant meets the design
requirements and is essentially asking the question “are we building the thing right?” [26,27]. It is essential that
verification is considered early in the design process. Ideally, when a design requirement is decided, a method
for verifying that requirement should also be developed [27]. Design verification methods can include:
• finite element analysis
• risk analysis
• rapid prototyping
2.5.2. Finite Element Analysis
Finite element analysis is a widely used technique in medical device design and can be used to verify if
a design will have sufficient strength to withstand the loading conditions in the human body [28-47]. Finite
element analysis is a proven cost saving tool and can reduce design cycle time. In the development of a new
method for closing a median sternotomy using cannulated screws and wire, finite element analysis was used to
investigate the stresses acting between the screw and sternum [29]. In knee replacement implants, finite element
analysis can be used to optimise the bearing surfaces [30]. Finite element analysis can also be used to investigate
design changes to existing devices. For example, Mathias et al. [31] used finite element analysis to investigate
the effect of introducing holes into the femoral component of a total hip replacement implant to engage with a
stem introducer instrument and Leahy et al. [15] undertook a redesign of a flexible fixation system for the
lumbar spine based on an existing design.
2.5.3. Risk Analysis
A key part of the medical implant design process is to undertake a risk analysis [32]. Any medical
implant should be designed and manufactured so that it does not compromise the safety of patients or healthcare
workers. Manufacturers must eliminate or reduce risks as far as possible; any risks that exist must be weighed
against the benefits to the patient. The way to show risks have been eliminated or reduced is to undertake a risk
analysis. Many techniques, such as Failure Mode Effect Analysis and Fault Tree Analysis can be used in a risk
analysis; guidance for these methods can be found in standards [33] and [34], respectively. Failure Mode Effects
Analysis (FMEA) can have a number of variants which address different aspects of the product development
cycle, all of which use a bottom-up approach to evaluate risks associated with aspects of the design. Examples
of the variants are Design Failure Mode Effects Analysis (DFMEA), Process Failure Mode Effects Analysis
(PFMEA), Failure Mode Criticality Analysis (FMECA) and User Failure Mode Effects Analysis (UFMEA). The
aim of these methods is to consider all the possible risks associated with a medical device and identify ways that

these risks can be eliminated or reduced. In FMEA the occurrence, severity, and detection of each failure are
rated on a scale from 1 to 10. A risk priority number is then calculated by multiplying the three ratings together.
The design team must then decide if a possible failure mode is acceptable or if ways need to be found to reduce
it. [32].
It is also important not to isolate the medical implant from the surgical instruments, packaging,
sterilization; these have many risks associated with them that could adversely affect the performance of a
medical implant. An international standard for medical device risk analysis has been published [35]. Risk
analysis helps to realize a design if it is undertaken at an early stage and should be undertaken at stages during
the design process, including a final risk analysis.
2.5.4. Rapid Prototyping
Rapid prototyping is a very effect technique for verifying the design of medical implant as it aids
communication between engineers and surgeons [33]. Models of implants can be produced within hours by a
variety of methods such as Selective Laser Sintering (SLS), Fused Deposition Modeling (FDM) or three-
dimensional printing [34]. The surgeon can then inspect the models and size them against a skeleton. Rapid
prototyping can also be used to produce models of human bones, which is particular useful if there is abnormal
anatomy into which an implant will be used [34].In fact rapid prototyping or 3D printing can also be used to
manufacture a patient specific implant.
2.6. Manufacture
Before the design is transferred to production it is essential to ensure that the chosen manufacturing
processes are repeatable and reliable. The choice of manufacturing technique depends on many factors:
• number to be produced
• surface finish required
• post machining cleaning processes
• sterilization process (if necessary)
As well as the manufacture of the implant, packaging for the implant, sterilization techniques,
operation instructions and requirements also need to be finalized.
2.7. Design Validation
Validation of the device is performed under actual or simulated conditions for use. While verification is
answering the question “are we building the thing right”, validation is asking “have we built the right thing”
[26,27]. Validation is to ensure that the medical device meets the user requirements and the intended use.
Validation can include:
• mechanical testing of prototypes
• evidence that similar medical devices are clinically safe
• a clinical investigation
• sterilization validation
Mechanical testing allows the mechanical conditions in the human body to be simulated in the
laboratory. Mechanical testing will give no indication of how the device will behave in the body from a
biological point of view, but it will ensure that devices have sufficient strength and stiffness to perform as
required. There are a large number of standards available to guide the pre-clinical mechanical testing of joint
replacement implants.
In some cases of mechanical testing it is beneficial to use human cadaveric material [39]. For example,
cadavers have been used to investigate the attachment of a hook device to the spinous process of the lumbar
spine in terms of strength and slippage [38,41]. In addition, cadavers can be used to trial surgical instruments
[41]. Once pre-clinical testing has been completed manufacturers of joint replacement implants are required to
make a decision as to whether a clinical investigation is required. This is guided by the standards.A critical
review of the literature is required to ascertain similar implants and how they have performed in patients.
2.8. Design Transfer
Before a design is transferred to production it is necessary to ensure that all documents and training
associated with the device are in place. Design transfer can include:
• generation of instructions for use
• finalization of the surgical technique

• plan the training of surgeons
• finalization of the packaging
• completed vendor requirements such as audits, first article inspection or surveys
• Total cost bill of materials
• completed inspection plans and process worksheets
• creation of the master device record
2.9. Design Changes
After a medical device is on the market it is necessary for the manufacturer to have a post-market
surveillance process in place to ensure the safety of patients and healthcare workers after the device is on the
market. Feedback from surgeons may lead to design changes being made to the device or the surgical
instruments. The changes that arise from this feedback must be fully documented.
III. Conclusion
The design process for the medical implant is discussed in detail here. It is applicable to all the
orthopedic implant which are not patient specific. Certain modifications can be done to the design process based
on new manufacturing techniques developed, requirement of patient specific implants, new materials available.
IV. Future Scope
With the advancement in CAD, Computer Imaging, manufacturing it can be seen that 3D printing can
be used to manufacture the patient specific implants as each and every patient will have different body features
so patient specific implants can be manufactured having complex features. It can also be noted that the implant
manufacturing process is very generalized as it does not consider patient specific data. Also the manufacturing
lead time of implant manufacturing is matter of concern as sometimes a patient can need the implant to be done
in very less time e.g. accident trauma. So efforts can be made to create a design process for additive
manufacturing as it can manufacture complex shapes and also which will reduce the manufacturing lead time so
a patient can get an implant in very less time.
References
[1]. Council Directive 93/42/EEC of 14 June 1993 concerning medical devices. Official J. Eur. Commun., vol. L169, pp. 1–43, 1993.
[2]. P. McAllister and J. Jeswiet, “Medical device regulation for manufacturers,” Proc. Inst. Mech. Eng. Part H J. Eng. Med., vol. 217,
pp. 459-467, 2003.
[3]. BS EN ISO 13485: 2003 Medical devices - Quality management systems-Requirements for regulatory purposes. London: British
Standards Institute, 2003.
[4]. PD CEN ISO/TR 14969: 2005 Medical devices - Quality management systems - Guidance on the application of ISO 13485:2003.
London: British Standards Institute, 2005.
[5]. FDA 21CFR820 Quality System Regulation. Rockville, Maryland, USA: Food and Drug Administration, 2006.
[6]. S. Pugh, Total design: integrated methods for successful product engineering. Harlow: Prentice Hall, 1991.
[7]. M. Kutz, Standard Handbook of Biomedical Engineering and Design. New York: McGraw-Hill, 2003.
[8]. N. Cross, Engineering Design Methods : strategies for product design. Chichester : J. Wiley, 2008.
[9]. K.S. Hurst, Engineering Design Principles. London : Arnold, 1999.
[10]. Clinical Trials Pf Medical Devices And Implants:Ethical Concernspamela S. Saha And Subrata Saha, Ieee Engineering In Medicine
And [11] Biology Magazine, June 1988 .
[11]. BS EN 12563: 1999 Non-active surgical implants - Joint replacement implants - Specific requirements for hip joint replacement
implants. London: British Standards Institute, 1999.
[12]. BS EN 12564: 1999 Non-active surgical implants - Joint replacement implants - Specific requirements for knee joint replacement
implants. London: British Standards Institute, 1999.
[13]. J.C. Leahy, E.C. Stevenson, D.W.L. Hukins, K.J. Mathias, D.E.T. Shepherd and D. Wardlaw, “Development of surgical instruments
for implanting a flexible fixation device for the lumbar spine,” Proc. Inst. Mech. Eng. Part H J. Eng. Med., vol. 214, pp. 325-328,
2000.
[14]. Orthopedic Implant Design, Analysis, and Manufacturing System R. Larry Dooley, Ph. D., Aiit Dingankar, M.S.,G.
Heimke,D.Sc.,E. Berg, M.D Magazine, june 1988.
[15]. E.B. Longton, B.B. Seedhom, “Total knee replacement”, In: D. Dowson and V. Wright, Eds. Introduction to the Biomechanics of
Joints and Joint Replacement, London: Mechanical Engineering Publications Ltd, 1981, pp. 199-206.
[16]. D.E.T. Shepherd and A.J. Johnstone, “Design considerations for a wrist implant,” Med. Eng. Phys., vol. 24, pp. 641-650, 2002.
[17]. A.H. Murdoch, D.E.T. Shepherd, K.J. Mathias and E.C. Stevenson, “Design of a retractable intra-medullary nail for the humerus,”
Biomed. Mater Eng., vol. 13, pp. 297-307, 2003.
[18]. P.S. Goel and N. Singh, “Creativity and innovation in durable product development,” Comput. Ind. Eng., vol. 35, pp. 5-8, 1998.
[19]. A.M. King and S. Sivaloganathan, “Development of a methodology for concept selection in flexible design strategies,” J. Eng.
Design, vol. 10, pp. 329-349, 1999.
[20]. M.C. Yang, “Observations on concept generation and sketching in engineering design,” Res. Eng. Design, vol. 20, pp. 1-11, 2009.
[21]. K. Alexander and P.J. Clarkson, “Good design practice for medical devices and equipment, part I: a review of current literature,” J.
Med. Eng. Technol., vol. 24, pp. 5-13, 2000.
[22]. K. Alexander and P.J. Clarkson, “Good design practice for medical devices and equipment, Part II: design for validation,” J. Med.
Eng. Technol., [23] vol. 24, pp. 53-62, 2000.
[23]. R. Contro and P. Vena, “Computational models for biological tissues and biomedical implants,” Eng. Comput., vol. 20, pp. 513-
523, 2003.

[24]. R.S. Jutley, M.A. Watson, D.E.T. Shepherd and D.W.L. Hukins, “Finite element analysis of stress around a sternum screw used to
prevent sternal dehiscence after heart surgery,” Proc. Inst. Mech. Eng. Part H J. Eng. Med., vol. 216, pp. 315-321, 2002.
[25]. D.J. Simpson, H. Gray, D. D’Lima, D.W. Murray, H.S. Gill, “The effect of bearing congruency, thickness and alignment on the
stresses in unicompartmental knee replacements,” Clin. Biomech., vol. 23, pp. 1148-1157, 2008.
[26]. K.J. Mathias, J.C. Leahy, A. Heaton, W.F. Deans and D.W.L. Hukins, “Hip joint prosthesis design: Effect of stem introducers,”
Med. Eng. Phys., vol. 20, pp. 620-624, 1998.
[27]. D.E.T. Shepherd, “Risk analysis for a radio-carpal joint replacement,” Proc. Inst. Mech. Eng. Part H J. Eng. Med., vol. 216, pp. 23-
29, 2002.
[28]. BS EN 60812: 2006 Analysis techniques for system reliability. Procedure for failure mode and effects analysis (FMEA). London:
British Standards Institute, 2006.
[29]. BS EN 61025: 2007 Fault tree analysis (FTA). London: British Standards Institute, 2007.
[30]. BS EN ISO 14971: 2001 Medical devices - Application of risk management to medical devices. London: British Standards Institute,
2001.
[31]. D.E.T. Shepherd and A.J. Johnstone, “A new design concept for wrist arthroplasty,” Proc. Inst. Mech. Eng. Part H J. Eng. Med.,
vol. 219, pp. 43-52, 2005.
[32]. D. Dimitrov, K. Schreve and N. de Beer, “Advances in three dimensional printing - state of the art and future perspectives,” Rapid
Prototyping J., vol. 12, pp.136-147, 2006.
[33]. J.R. Meakin, D.E.T. Shepherd and D.W.L. Hukins, “Fused deposition models from CT scans,” Br. J. Radiol., vol. 77, pp. 504-507,
2004.
[34]. BS 7251-12, Orthopedic joint prostheses. Specification for endurance of stemmed femoral components with application of torsion.
London: British Standards Institute, 1995.
[35]. Next Generation Orthopaedic implants by Additive Manufacturing Using Electron Beam Melting Lawrence E.Murr, Sara M.
Gaytan, Edwin Martinez,Frank Medina, and Ryan B.Wicker, International Journal of Biomaterials Volume 2012.
[36]. M.M.M. Willems, J. Kooloos, P. Gibbons, N. Minderhoud, T. Weernink and N. Verdonschot, “The stability of the femoral
component of a minimal invasive total hip replacement system,” Proc. Inst. Mech. Eng. Part H J. Eng. Med., vol. 220, pp. 465-472,
2006.
[37]. D.E.T. Shepherd, J.C. Leahy, K.J. Mathias, S.J. Wilkinson and D.W.L. Hukins, “Spinous process strength,” Spine, vol. 25, pp. 319-
323, 2000.
[38]. D.E.T. Shepherd, J.C. Leahy, D.W.L. Hukins and D. Wardlaw, “Slippage of a spinous process hook during flexion in a flexible
fixation system for the lumbar spine,” Med. Eng. Phys., vol. 23, pp. 135-141, 2001.
[39]. M. Mason, A. Belisle, P. Bonutti, F.R. Kolisek, A. Malkani and M. Masini, “An accurate and reproducible method for locating the
joint line during a revision total knee arthroplasty,” J. Arthroplasty, vol. 21, pp. 1147-1153, 2006
[40]. OrthopaedicImplants and Prostheses.Conventional and Unconventional,Processing Technologies Simona MIHAI, International
Conference on Advances in Electrical and Mechanical Engineering (ICAEME'2012) 18-19, 2012.
[41]. Modeling metal deposition in heat transfer analysis of additive manufacturing processes, Panagiotis Michaleris, Finite Elements in
Analysis and Design86(2014)51–60
[42]. A Review of the Design Process for Implantable Orthopedic Medical Devices,G.A. Aitchison,D.W.L. Hukins, J.J. Parry, D.E.T.
Shepherd, S.G. Trotman, The Open Biomedical Engineering Journal, 2009, 3, 21-27.

L012627682

More Related Content

What's hot (18)

Viewers also liked (20)

Similar to L012627682 (20)

More from IOSR Journals (20)

Recently uploaded (20)

L012627682