Launch CReader V+ User Manual

Table of Contents
1. INTRODUCTION ...........................................................................................1
2. GENERAL INFORMATION-ABOUT OBDII/EOBD ......................................1
2.1 ON-BOARD DIAGNOSTICS (OBD) II.....................................................1
2.2 DIAGNOSTIC TROUBLE CODES (DTCS)................................................2
2.3 LOCATION OF THE DATA LINK CONNECTOR (DLC) ................................3
2.4 OBD II READINESS MONITORS............................................................3
2.5 OBD II MONITOR READINESS STATUS .................................................4
2.6 OBD II DEFINITIONS ..........................................................................5
3. PRODUCT DESCRIPTIONS.........................................................................7
3.1 OUTLINE OF CREADER V+ ..................................................................7
3.2 SPECIFICATIONS ................................................................................8
3.3 ACCESSORIES ...................................................................................8
3.4 POWER SUPPLY .................................................................................8
3.5 TOOL SETUP .....................................................................................9
3.6 VEHICLE COVERAGE ........................................................................10
4. OPERATIONS .............................................................................................11
4.1 CONNECTION...................................................................................11
4.2 DIAGNOSE.......................................................................................11
4.2.1 Read Codes...........................................................................12
4.2.2 Erase Codes ..........................................................................13
4.2.3 I/M Readiness........................................................................15
4.2.4 Data Stream...........................................................................16
4.2.5 View Freeze Frame................................................................18
4.2.6 O2 sensor test........................................................................18
4.2.7 On-board monitor test............................................................19
4.2.8 EVAP System Test ................................................................20
4.2.9 Vehicle Info ............................................................................21
4.3 DTC LOOKUP..................................................................................21
4.5 HELP ..............................................................................................22
5. UPGRADING...............................................................................................23
6 FAQ ..............................................................................................................24

LAUNCH Creader V+ User’s Manual
1
1. INTRODUCTION
Creader V+ is the next generation of vehicle fault diagnosis tool developed
by Launch, especially for the DIY users and the servicemen of small
service workshop. It supports read/clear DTCs and read datastream. With
built-in help menus and code definitions, diagnosing and repairing that
dreaded Check Engine Light is now easier than ever!
Moreover, Creader V+ also feature the following bi-directional “special tests”:
EVAP, O2 Sensor, I/M Readiness, MIL Status, VIN Info, and On-board monitors
testing.
It can be connected to PC through the USB cable for upgrade to keep updated
with the latest software version.
Notice: Creader V+ may automatically reset while being disturbed by strong
static electricity. THIS IS A NORMAL REACTION.
2. General Information-About OBDII/EOBD
2.1 On-Board Diagnostics (OBD) II
The first generation of On-Board Diagnostics (called OBD I) was developed by
the California Air Resources Board (ARB) and implemented in 1988 to monitor
some of the emission control components on vehicles. As technology evolved
and the desire to improve the On-Board Diagnostic system increased, a new
generation of On-Board Diagnostic system was developed. This second
generation of On-Board Diagnostic regulations is called "OBD II".
The OBD II system is designed to monitor emission control systems and key
engine components by performing either continuous or periodic tests of specific
components and vehicle conditions. When a problem is detected, the OBD II
system turns on a warning lamp (MIL) on the vehicle instrument panel to alert
the driver typically by the phrase of “Check Engine” or “Service Engine Soon”.
The system will also store important information about the detected malfunction
so that a technician can accurately find and fix the problem. Here below follow
three pieces of such valuable information:
1) Whether the Malfunction Indicator Light (MIL) is commanded 'on' or 'off';
2) Which, if any, Diagnostic Trouble Codes (DTCs) are stored;
3) Readiness Monitor status.

2
2.2 Diagnostic Trouble Codes (DTCs)
OBD II Diagnostic Trouble Codes are codes that are stored by the on-board
computer diagnostic system in response to a problem found in the vehicle.
These codes identify a particular problem area and are intended to provide you
with a guide as to where a fault might be occurring within a vehicle. OBD II
Diagnostic Trouble Codes consist of a five-digit alphanumeric code. The first
character, a letter, identifies which control system sets the code. The second
character, a number, 0-3; other three characters, a hex character, 0-9 or A-F
provide additional information on where the DTC originated and the operating
conditions that caused it to set. Here below is an example to illustrate the
structure of the digits:

3
2.3 Location of the Data Link Connector (DLC)
The DLC (Data Link Connector or Diagnostic Link Connector) is the
standardized 16-cavity connector where diagnostic code readers interface with
the vehicle's on-board computer. The DLC is usually located 12 inches from the
center of the instrument panel (dash), under or around the driver’s side for most
vehicles. If Data Link Connector is not located under dashboard, a label should
be there telling location. For some Asian and European vehicles, the DLC is
located behind the ashtray and the ashtray must be removed to access the
connector. If the DLC cannot be found, refer to the vehicle’s service manual for
the location.
2.4 OBD II Readiness Monitors
An important part of a vehicle’s OBD II system is the Readiness Monitors, which
are indicators used to find out if all of the emissions components have been
evaluated by the OBD II system. They are running periodic tests on specific
systems and components to ensure that they are performing within allowable
limits.
Currently, there are eleven OBD II Readiness Monitors (or I/M Monitors) defined
by the U.S. Environmental Protection Agency (EPA). Not all monitors are
supported in every vehicles and the exact number of monitors in any vehicle
depends on the motor vehicle manufacturer’s emissions control strategy.
Continuous Monitors -- Some of the vehicle components or systems are
continuously tested by the vehicle’s OBD II system, while others are tested only
under specific vehicle operating conditions. The continuously monitored
components listed below are always ready:
1）Misfire

4
2）Fuel System
3）Comprehensive Components (CCM)
Once the vehicle is running, the OBD II system is continuously checking the
above components, monitoring key engine sensors, watching for engine misfire,
and monitoring fuel demands.
Non-Continuous Monitors -- Unlike the continuous monitors, many emissions
and engine system components require the vehicle to be operated under
specific conditions before the monitor is ready. These monitors are termed
non-continuous monitors and are listed below:
1) EGR System
2) O2 Sensors
3) Catalyst
4) Evaporative System
5) O2 Sensor Heater
6) Secondary air Injection
7) Heated Catalyst
8) A/C system
2.5 OBD II Monitor Readiness Status
OBD II systems must indicate whether or not the vehicle’s PCM’s monitor
system has completed testing on each component. Components that have been
tested will be reported as “Ready”, or “Complete”, meaning they have been
tested by the OBD II system. The purpose of recording readiness status is to
allow inspectors to determine if the vehicle’s OBD II system has tested all the
components and/or systems.
The powertrain control module (PCM) sets a monitor to “Ready” or “Complete”
after an appropriate drive cycle has been performed. The drive cycle that
enables a monitor and sets readiness codes to “Ready” varies for each
individual monitor. Once a monitor is set as “Ready” or “Complete”, it will remain
in this state. A number of factors, including erasing of diagnostic trouble codes
(DTCs) with a code reader or a disconnected battery, can result in Readiness
Monitors being set to “Not Ready”. Since the three continuous monitors are
constantly evaluating, they will be reported as “Ready” all of the time. If testing of
a particular supported non-continuous monitor has not been completed, the
monitor status will be reported as “Not Complete” or “Not Ready.”
In order for the OBD monitor system to become ready, the vehicle should be
driven under a variety of normal operating conditions. These operating
conditions may include a mix of highway driving and stop and go, city type

5
driving, and at least one overnight-off period. For specific information on getting
your vehicle’s OBD monitor system ready, please consult your vehicle owner’s
manual.
2.6 OBD II Definitions
Powertrain Control Module (PCM) -- OBD II terminology for the on-board
computer that controls engine and drive train.
Malfunction Indicator Light (MIL) -- Malfunction Indicator Light (Service
Engine Soon, Check Engine) is a term used for the light on the instrument panel.
It is to alert the driver and/or the repair technician that there is a problem with
one or more of vehicle's systems and may cause emissions to exceed federal
standards. If the MIL illuminates with a steady light, it indicates that a problem
has been detected and the vehicle should be serviced as soon as possible.
Under certain conditions, the dashboard light will blink or flash. This indicates a
severe problem and flashing is intended to discourage vehicle operation. The
vehicle onboard diagnostic system cannot turn the MIL off until the necessary
repairs are completed or the condition no longer exists.
DTC -- Diagnostic Trouble Codes (DTC) that identifies which section of the
emission control system has malfunctioned.
Enabling Criteria -- Also termed Enabling Conditions. They are the
vehicle-specific events or conditions that must occur within the engine before the
various monitors will set, or run. Some monitors require the vehicle to follow a
prescribed “drive cycle” routine as part of the enabling criteria. Drive cycles vary
among vehicles and for each monitor in any particular vehicle. Please refer to
the vehicle's factory service manual for specific enabling procedures.
OBD II Drive Cycle -- A specific mode of vehicle operation that provides
conditions required to set all the readiness monitors applicable to the vehicle to
the “ready” condition. The purpose of completing an OBD II drive cycle is to
force the vehicle to run its onboard diagnostics. Some form of a drive cycle
needs to be performed after DTCs have been erased from the PCM’s memory or
after the battery has been disconnected. Running through a vehicle’s complete
drive cycle will “set” the readiness monitors so that future faults can be detected.
Drive cycles vary depending on the vehicle and the monitor that needs to be
reset. For vehicle specific drive cycle, consult the service manual.
Freeze Frame Data -- When an emissions related fault occurs, the OBD II
system not only sets a code but also records a snapshot of the vehicle operating

6
parameters to help in identifying the problem. This set of values is referred to as
Freeze Frame Data and may include important engine parameters such as
engine RPM, vehicle speed, air flow, engine load, fuel pressure, fuel trim value,
engine coolant temperature, ignition timing advance, or closed loop status.
Fuel Trim (FT) - Feedback adjustments to the base fuel schedule. Short-term
fuel trim refers to dynamic or instantaneous adjustments. Long-term fuel trim
refers to much more gradual adjustments to the fuel calibration schedule than
short-term trim adjustments. These long-term adjustments compensate for
vehicle differences and gradual changes that occur over time.

7
3. Product Descriptions
3.1 Outline of Creader V+
Figure 3-1
No. Name Notes
1 Cable with OBD II
CONNECTOR
Connects the Creader V+ to the vehicle’s
Data Link Connector (DLC).
2 RED LED
INDICATOR LAMP
DTC indicator; when confirmed or
pending DTCs are found, the red
indicator lamp will light up.

8
3 LCD DISPLAY Indicates test results.
4 EXIT BUTTON Returns to previous menu.
5 UP BUTTON Move cursor up for selection.
6 ENTER BUTTON Confirms a selection (or action) from a
menu list.
7 RIGHT BUTTON Move cursor right for selection; Or turn
page down when more than one page is
displayed.
8 DOWN BUTTON Move cursor down for selection.
9 LEFT BUTTON Move cursor left for selection; Or turn
page up when more than one page is
displayed.
10 USB PORT Connects to computer to update the
Creader V+ online.
3.2 Specifications
1) Screen: 2.4” TFT, 176*220 dots LCD display
2) Input voltage range: 9 ~ 18V
3) Operating temperature: 32°F~122°F / 0°C~50°C
4) Storage tempetature: -4°F~158°F / -20°C ~70°C @ RH60%
5) Outline dimension: 120*75*20 mm (L x W x H)
6) Weight : <17.6 oz (500g)
3.3 Accessories
1) User’s Manual -- Instructions on tool operations
2) USB cable -- Connect to a computer for upgrading online
3.4 Power supply
The power of the Creader V+ is provided via the vehicle Data Link Connector
(DLC). Follow the steps below to power it up:
1) Find DLC on vehicle
A plastic DLC cover may be found for some vehicles and you need to
remove it before plugging the OBDII cable.
2) Plug the connector at the end of OBD II cable to the vehicle’s DLC.

9
3.5 Tool Setup
Select [Tool Setup] in the Main Menu and press [ ], the screen will display the
interface as shown below:
Figure 3-2
The Creader V+ allows you to make the following settings:
1) Select language: Selects desired language.
Choose [Language] and press [ ], the screen will display the interface as
shown below:
Figure 3-3
You can press [ ] [ ] key to select any language and press [ ] to confirm. The
system will convert to the chosen language interface at once.
2) Set measurement unit: allows you to define the measurement unit.
Choose [Unit of Measure] and press [ ], the screen will display the interface as
shown below:

10
Figure 3-3
Use the [ ] [ ] key to select the desired one and press [ ] to save your
change.
3.6 Vehicle Coverage
The Creader V+ is specially designed to work with all OBD II compliant vehicles,
including Control Area Network (CAN). It is required by EPA that all 1996 and
newer vehicles (cars and light trucks) sold in the United States must be OBD II
compliant and this includes all American, Asian and European vehicles.
A small number of 1994 and 1995 model year gasoline vehicles are OBD II
compliant. To verify if a 1994 or 1995 vehicle is OBD II compliant, check the
Vehicle Emissions Control Information (VECI) Label, which is located under the
hood or by the radiator of most vehicles. If the vehicle is OBD II compliant, the
label will designate “OBD II Certified”. Additionally, Government regulations
mandate that all OBD II compliant vehicles must have a “common” sixteen-pin
Data Link Connector (DLC).
For the vehicle to be OBD II compliant it must have a 16-pin DLC (Data Link
Connector) under the dash and the Vehicle Emission Control Information Label
must state that the vehicle is OBD II compliant.

11
4. Operations
4.1 Connection
1) Turn the ignition off.
2) Locate the vehicle’s 16-pin Data Link Connector (DLC).
3) Plug the OBDII cable into the vehicle’s DLC.
4) Turn the ignition on. Engine can be off or running.
5) After finishing, press [ ] button to enter Main Menu as following figure 4-1:
Figure 4-1
CAUTION: Don’t connect or disconnect any test equipment with ignition on
or engine running.
4.2 Diagnose
Select [Diagnostic] in Main Menu and press [ ], the screen will display Monitor
Status interface as following figure 4-2:
Figure 4-2

12
Press [ ] to enter the Diagnostic Menu, the screen will display as following
figure 4-3:
Figure 4-3
4.2.1 Read Codes
Select [Read Codes] and press [ ] in Diagnostic Menu. A screen similar to
Figure 4-4 will pop up:
Figure 4-4
Press [ ] to enter to select the manufacturer. Figure 4-5 will be shown on the
screen. Press [ ] / [ ] to select different items; press [ ] / [ ] to turn to next or
previous page. After selecting the desired one, press [ ] to confirm.

13
Figure 4-5
If there are some codes, the screen will display the codes as shown below:
Figure 4-6
1/39 indicates there are 39 codes total and now P0100 is the first code to
display.
The screen will also show the content of the code below the number of code.
You can use [ ] key to view the next code.
After viewing all the codes, you can press [ ] to return to the Diagnostic Menu.
4.2.2 Erase Codes
Select [Erase Codes], the screen will display the interface as shown below:

14
Figure 4-7
Press [ ] to erase DTC’s, and the screen will display the interface as shown
below:
Figure 4-8
According to the above figure to press [ ] and the screen will display the
interface as shown on the next page:
Figure 4-9

15
Notes: After clearing, you should retrieve trouble codes once more or turn
ignition on and retrieve codes again. If there are still some trouble codes in the
system, please troubleshoot the code using a factory diagnosis guide, then clear
the code and recheck.
4.2.3 I/M Readiness
I/M refers to Inspection and Maintenance that is legislated by the Government to
meet federal clean-air standards. I/M Readiness indicates whether or not the
various emissions-related systems on the vehicle are operating properly and are
ready for Inspection and Maintenance testing.
The purpose of the I/M Readiness Monitor Status is to indicate which of the
vehicle’s Monitors have run and completed their diagnosis and testing (as
described in Chapter 2.5), and which ones have not yet run and completed
testing and diagnosis of their designated sections of the vehicle’s emissions
system.
The I/M Readiness Monitor Status function also can be used (after repair of a
fault has been performed) to confirm that the repair has been performed
correctly, and/or to check for Monitor Run Status.
Select [I/M Readiness] and press [ ], the screen will display the interface as
shown below:
Figure 4-10
You can use [ ]/ [ ] button to select and press [ ], the screen will display the

16
Figure 4-11
You can use [ ]/ [ ] button to view other data of vehicle.
N/A means not available on this vehicle, INC means incomplete or not ready,
OK means Completed or Monitor Ok.
Press [ ] to return to Diagnostic Menu.
4.2.4 Data Stream
Press [ ] [ ] button to select Data Stream in Main Menu interface and then
press [ ] button to confirm, the screen will display the interface as shown
below:
Figure 4-12
Select [View All Items] and press [ ] button, the screen will display the interface
as shown below:

17
Figure 4-13
You can use [ ] [ ] button to view other data streams.
Select [Select Items] in Data stream menu and press [ ], the screen will display
the interface as shown below:
Figure 4-14
You can use [ ] / [ ] button to select data stream items, and press [ ] / [ ]
button to turn page.
After selecting items, press [ ], the screen will display the selected datastream
items.
To select all datastream of the current page, highlight the first line and then press
[ ], √ will appear before all items. To deselect all, just press [ ] again.
If [View Graphic Items] is selected in Datastream menu and press [ ] to enter
the graphic items selection screen.
Press [ ] / [ ] button to select single data stream items, and press [ ] button,

18
the screen will display the selected items of live graphic data.
4.2.5 View Freeze Frame
When an emission-related fault occurs, certain vehicle conditions are recorded
by the on-board computer. This information is referred to as freeze frame data.
Freeze Data is a snapshot of the operating conditions at the time of an
emission-related fault.
Note: if DTCs were erased, Freeze Data may not be stored in vehicle
memory depending on vehicle.
Select [Freeze Frame] in main menu interface, the screen will display the
Figure 4-15
You can use [ ] [ ] button to view the data.
4.2.6 O2 sensor test
The results of O2 sensor test are not live values but instead the results of the
ECU’s last O2 sensor test. For live O2 sensor readings, refer to any of the live
sensor screens such as Graph Screen.
Not all test values are applicable to all vehicles. Therefore, the list generated will
vary depending on vehicle. In addition, not all vehicles support the Oxygen
Sensors screen.
For results of latest mandated on-board oxygen sensor monitoring test, see
Figure 4-16 below:

19
Figure 4-16
Select [O2 Sensor Test] in Diagnostic Menu and press [ ] and the screen will
display as shown below:
Figure 4-17
You can use [ ] [ ] button to select an item and press [ ], then follow the
on-screen instructions to perform the test.
4.2.7 On-board monitor test
This function can be utilized to read the results of on-board diagnostic
monitoring tests for specific components/systems.
Select [On-board Monitoring] in main menu and press [ ] and the screen will

20
Figure 4-18
You can use [ ] [ ] button to select an item and press [ ], the screen will
Figure 4-19
4.2.8 EVAP System Test
The EVAP test function lets you initiate a leak test for the vehicle’s EVAP system.
The Creader V+ does not perform the leak test, but signals to vehicle’s on-board
computer to initiate the test. Before using the system test function, refer to the
vehicle’s service repair manual to determine the procedures necessary to stop
the test.
Select [EVAP System Test] and press [ ], the screen will display the relative
information about EVAP system. Some vehicle manufacturers do not allow
external devices to control vehicle system. If the car supports this function, it will
display as below:

21
Figure 4-20
4.2.9 Vehicle Info
Select [Vehicle Info] and press [ ], the screen will display the information, such
as VIN (Vehicle identification Number), CID (Calibration ID) and CVN
(Calibration verification number), as shown below:
Figure 4-21
4.3 DTC Lookup
Select [Code Lookup] in the Main Menu and press [ ] and the screen will
display the interface as shown below:

22
Figure 4-22
You can use [ ] [ ] key to change the first letter. It can be switched among “P”,
“B”, “C” and “U”. Press [ ] to move the cursor to next, and then press [ ] [ ]
key to input number. After you input the code number, press [ ] to view the
definition of the code.
After viewing the definition, press [ ] to return to the Main Menu.
4.5 Help
This function is used to view Tool Information, About OBD, and About Data
stream.
Figure 4-23
Tool Information includes: software version, hardware version, serial number,
supported, time and date.
About OBD: Relevant introductions information about OBD.
About Data stream: Relevant introductions information about Data stream.

23
5. Upgrading
Download the latest version of the Creader V+ upgrade package, and then
decompress the software to local disk. Click it to run and install it until it is
complete.
Connect the Creader V+ to computer through USB cable and run the Creader
V+ Upgrade.exe, a screen similar to the following figure will appear:
Figure 5-1
Select the language, and then click "Start Upgrade" when a message of
upgrading succeed pops up, click” Exit”, unplug USB cable to complete upgrade.

24
6 FAQ
Here we list some frequently asked questions and answers relating to Creader
V+.
Question: System halts when reading data stream. What is the reason?
Answer: It may be caused by a slackened connector. Please turn off the
Creader V+, firmly connect the connector, and switch on it again.
Question: Screen of main unit flashes at engine ignition start.
Answer: Caused by electromagnetic disturbance and this is normal
phenomenon.
Question: There is no response when communicating with on-board computer.
Answer: Please confirm the proper voltage of power supply and check if the
throttle has been closed, the transmission is in the neutral position, and the
water is in proper temperature.
Question: Why are there so many fault codes?
Answer: Usually, it’s caused by poor connection or fault circuit grounding.

Launch CReader V+ User Manual

More Related Content

What's hot (20)

Similar to Launch CReader V+ User Manual (20)

More from Tim Miller (20)

Recently uploaded (20)

Launch CReader V+ User Manual