Lighting Design Principles Lecture 1.ppt

Lighting Design Principles
1. Physics terminology and parameters
2024/2025 Eng. Anan Kakani 1

Parameters
Parameter Symbol Unit
Luminous flux Φ lumen [lm]
Luminous efficacy η lumens per watt [lm/W]
Luminous energy Q lumen seconds [lms]
Light yield I candela [cd]
Illuminance E lux [lx]
Daylight factor D percentage [%]
Light density L candela per m² [cd/m²]
Colour temperature - Kelvin [K]
Colour rendering index Ra -
2
2024/2025 Eng. Anan Kakani

Terms, Units, and Definitions
Photometrische Größe SI unit and calculation Definition
Luminous flux Lumen (lm) The measure for the total amount of light emitted by a light source.
Light intensity Candela (cd) = lm/sr
The ratio of lumen to radiation angle. Gives information about how
much light is radiated in a certain direction.
Illuminance Lux (lx) = lm/m² The measure for the light that arrives at a receiver surface.
Luminance cd/m²
The measure for the impression of brightness of a surface, perceived
by the human eye.
Luminous efficacy lm/W The ratio of emitted luminous flux to required electrical power.
Light quantity lm*s
The total luminous flux emitted by a light source over a certain
period of time.
3

The light and colour spectrum
• To the human eye, only a minuscule part of the electromagnetic
spectrum is perceptible. This field is known as the light or colour
spectrum. It is also frequently referred to as natural “light”.
• Higher-frequency ranges with short wavelengths (such as UV or X-
rays) and low-frequency ranges with long wavelengths (microwaves
and radio waves) are invisible to the human eye. Within the range of
the visible light spectrum, it is possible to determine the diverse
wavelengths of the colour tones
4

Luminous flux, luminous efficacy and the
quantity of light
• Luminous flux Φ [lm] shows how much light is radiated from a light
source. To establish this fact, the human eye is needed as an
evaluating organ. When calculating the luminous efficacy, the
quantity of light, the light yield and the luminance, it is essential to
regard luminous flux as a baseline value.
6

Light yield I [cd]
• Light yield I [cd] determines the
ratio of light emitted by a light
source moving in a specific
direction.
• The luminous intensity of natural
light sources can be influenced by
the use not only of sun-shade and
glare protection, but also of glazing
and light control.
• In the case of artificial light, these
are the essential light models and
light sources/illuminants used.
7

Illumination densities
• In the case of illuminance E [lx; lm/m²], the luminous flux represents
a specific illuminated area.
• When illuminating workplaces, extensive normative specifications
determine which values are reached or should not be exceeded.
• In the case of daylight planning, the decisive values are generally the
readily available illumination intensities of natural light sources;
• When planning artificial lighting, calculations should be made, and
simulation models calculated to ascertain which lights and illuminants
will be needed to produce the necessary illumination intensity
9

The illumination intensities of natural light
sources on the ground
Light source Luminance [lx]
Clear sky, sunny (summer) 90,000–130,000
Clear sky, sunny (winter) 19,000–25,000
Cloudy sky (summer) 15,000–20,000
Cloudy sky (winter) 5,000–8,000
Dusk 3–750
Moonlight 0.02–0.30
10

Light density
• Light density is the parameter within physics that describes the brightness
experienced by human beings. It is one of the few units extremely
dependent on the direction of a light source.
• luminance is always dependent on a generator and not — as in the case of
most other parameters — on the recipient of the light radiation, i.e., the
human eye.
• The awareness of darkness and glare through the perception of diverse
sensitivities of the eye varies according to the eye’s sensitivity. Not only
that, but the eye also adapts itself to certain situations over time.
• The wavelengths of light, that is, the perceived colour, ensure that similar
light densities trigger differentiated feelings
11

The perception and sensitivity of the human
eye
Viewing task Light density
Night vision 3–30 µcd/m² – 3–30 mcd/m²
Twilight 3–30 mcd/m² – 3–30 cd/m²
Daylight > 3–30 cd/m²
Dazzle > 100,000–1,000,000 cd/m²
13

Light/bright colour and colour temperature
• Luminous colour or colour temperature (unit of measure: Kelvin)
describes a colour impression produced by a light source.
• A lower value alludes to a large share of red in the existing colour
spectrum, in which subjective perception is experienced as warm. Above
all, in the planning of the temperature, the colour plays a significant role in
determining the artificial light sources since the planning goal generally is
to simulate natural light.
• The technical capabilities generally end with colour temperatures well
below those of natural light. Light sources with a colour temperature of
under 3,300 K are registered as warm-white and have a neutral white
spectrum fluctuating between 3,300 and 5,000 K; higher values result in
warm “daylight white” or ”cold white” light sources.
14

Exemplary colour temperatures of natural
and artificial sources of light
The source of light Colour temperature [K]
Candle 1,500
Light bulb (60 W) 2,700
Light bulb (200 W) 3,000
Halogen lamp (12 V) 3,000–3,200
Fluorescent lamp (neutral white) 4,000
Morning/evening sun 5,000
Cloudy sky 6,500–7,500
Fog/haze 7,500–8,500
Clear sky 9,000–12,000
16

The colour rendering index
• The colour rendering index Ra displays the quality of the colour
rendering of diverse light sources. The process describes the impact
evoked by light directed at objects and other people.
• Good colour renditioning is achieved when a natural colour
environment is optimally reproduced (value Ra=100). In high-quality
interiors with good residential quality and/or workplaces with light
sources, an Ra < 80 should not be used. The colour rendering index Ra
refers to the eight most frequently used test colours. The index
makes this quite clear and means “in general” in this context.
17

Colour reproduction index with diverse light
sources
Source of light Colour rendering index Ra
Light bulb Up to 100
LED 80–97
OLED 80–90
Fluorescent lamp 50–98
Metal halide lamp 60–95
High-pressure sodium lamp 18–85
High-pressure quicksilver lamp 45
Low-pressure sodium vapour lamp < 44
19

Lighting Design Principles Lecture 1.ppt

More Related Content

Similar to Lighting Design Principles Lecture 1.ppt (20)

More from anan fmk (6)

Recently uploaded (20)

Lighting Design Principles Lecture 1.ppt