ELECTRICAL WIRING

ELECTRICAL WIRING
Electrical wiring is generally refers to
insulated conductor used to carry current
and associated device. This article
describes general aspects of electrical
wiring as used to provide power in
buildings and structures, commonly
referred to as building wiring.
Types of wiring according to uses
1. Domestic wiring.
2. Commercial wiring.
3. Industrial wiring.
FACTOR AFFECTING THE
CHOICE OF WIRING:
1. Durability: Type of wiring selected should conform to standard
specifications, so that it is durable i.e. without being affected by
the weather conditions, fumes etc.
2. Safety: The wiring must provide safety against leakage, shock and
fire hazards for the operating personnel.
3. Appearance: Electrical wiring should give an aesthetic appeal to
the interiors.
4. Cost: It should not be prohibitively expensive.
5. Accessibility: The switches and plug points provided should be
easily accessible. There must be provision for further extension of
the wiring system, if necessary.
6. Maintenance Cost: The maintenance cost should be a minimum
7. Mechanical safety: The wiring must be protected against any
mechanical damage
1

Types of Wiring
 Cleat wiring
 CTS wiring or TRS wiring or batten wiring
 Metal sheathed wiring or lead sheathed wiring
 Casing and capping
 Conduit wiring
Cleat Wiring:
Introduction
The types of wiring to be adopted is dependent on various factors, viz,
durability, safety, appearance, cost, consumer’s budget etc.
Cleat Wiring
This System uses insulated Cables sub protected in porcelain cleats.
2

Cleat wiring is recommended only for temporary installations. The
cleats are made in pairs having bottom and top halves. The bottom half
is grooved to receive the wire and the top half is for cable grip. Initially
the bottom and top cleats are fixed on the wall loosely according to the
layout. Then the cable is drawn, tensioned and the cleats are tightened
by the screw. Cleats are of three types, having one, two or three grooves,
so as to receive one, two or three wires. Two types of cleats.
Cleat wiring is one of the cheapest wiring considering the initial cost
and labor, and is most suitable for temporary wiring. This wiring can be
quickly installed, easily inspected and altered. When not required, this
wiring could be dismantled without damage to the cables, cleats and
accessories.
• Cleats
All cleats shall consist of two parts, a base piece and a cap. Cleats shall
be fixed at distances not more than 60 cm apart and at regular
intervals.
Where cleat wiring is laid along an iron joist, porcelain cleats shall be
inserted either with varnished wood fillets or varnished wood clamps
3

securely fixed so as to prevent the conductors from coming in contact
with the metal along witch they are passing.
• Fixing of cleats
In ordinary cases, cleats shall be attached to wooden plugs fixed to the
walls.
• Distance apart of wires
For pressure up to 250 volts, cleats shall be of such dimensions that in
the case of branch loads, conductors shall not be less than 2.5 cm apart,
centre to centre, and in the case of sub-mains not less than 4 cm apart,
centre to centre. Care shall be taken in selecting the size of cleats
particularly for branch distribution wiring where two-way and three-
way porcelain cleats are essential and the difference in size shall be
reasonable. Care should also be taken ensure that grooves f porcelain
cleats are essential and the difference in size shall be reasonable. Care
should also be taken ensure that grooves of porcelain cleats do not
compress the insulation nor be too wide for a loose fit. Under no
circumstances two wires shall be placed in one groove of the porcelain
cleats.
Advantages:
1) Easy installation.
2) Materials can be retrieved for reuse.
3) Flexibility provided for inspection, modifications and expansion.
4) Relatively economical.
5) Skilled manpower not required.
Disadvantages:
1) Appearance is not good.
2) Open system of wiring requiring regular cleaning.
3) Higher risk of mechanical injury.
Batten Wiring
4

In this wiring system, wires sheathed in tough rubber are used which
are quite flexible. They are clipped on wooden battens with brass clips
(link or joint) and fixed on to the walls or ceilings by flat head screws.
These cables are moisture and chemical proof. They are suitable for
damp climate but not suitable for outdoor use in sunlight. TRS wiring is
suitable for lighting in low voltage installations.
Advantages:
1. Easy installation and is durable
2. Lower risk of short circuit.
3. Cheaper than casing and capping system of wiring
4. Gives a good appearance if properly erected.
Disadvantages:
1. Danger of mechanical injury.
2. Danger of fire hazard.
3. Should not be exposed to direct sunlight.
4. Skilled workmen are required.
5

Metal Sheathed or Lead Sheathed wiring:
The wiring is similar to that of CTS but the conductors (two or three)
are individually insulated and covered with a common outer lead-
aluminum alloy sheath. The sheath protects the cable against dampness,
atmospheric extremities and mechanical damages. The sheath is earthed
at every junction to provide a path to ground for the leakage current.
They are fixed by means of metal clips on wooden battens. The wiring
system is very expensive. It is suitable for low voltage installations.
Precautions to be taken during installation:
1. The clips used to fix the cables on battens should not react with
the sheath.
2. Lead sheath should be properly earthed to prevent shocks due to
leakage currents.
3. Cables should not be run in damp places and in areas where
chemicals (may react with the lead) are used.
6

Advantages:
1. Easy installation and is aesthetic in appearance.
2. Highly durable.
3. Suitable in adverse climatic conditions provided the joints are not
exposed.
Disadvantages:
1. Requires skilled labor.
2. Very expensive.
3. Unsuitable for chemical industries.
Casing and Capping:
It consists of insulated conductors laid inside rectangular, teakwood or
PVC boxes having grooves inside it. A rectangular strip of wood called
capping having same width as that of casing is fixed over it. Both the
casing and the capping are screwed together at every 15 cms. Casing is
attached to the wall. Two or more wires of same polarity are drawn
through different grooves. The system is suitable for indoor and
domestic installations.
Advantages:
1. Cheaper than lead sheathed and conduit wiring.
2. Provides good isolation as the conductors are placed apart
reducing the risk of short circuit.
3. Easily accessible for inspection and repairs.
4. Since the wires are not exposed to atmosphere, insulation is less
affected by dust, dirt and climatic variations.
7

Disadvantages:
1. Highly inflammable.
2. Usage of unseasoned wood gets damaged by termites.
Skilled workmanship required
Conduit wiring:
In this system PVC (polyvinyl chloride) or VIR cables are run through
metallic or PVC pipes providing good protection against mechanical
injury and fire due to short circuit. They are either embedded inside the
walls or supported over the walls, and are known as concealed wiring or
surface conduit wiring (open conduit) respectively. The conduits are
buried inside the walls on wooden gutties and the wires are drawn
through them with fish (steel) wires. The system is best suited for public
buildings, industries and workshops.
Advantages:
1. No risk of fire and good protection against mechanical injury.
2. The lead and return wires can be carried in the same tube.
3. Earthing and continuity is assured.
4. Waterproof and trouble shooting is easy.
5. Shock- proof with proper earthing and bonding
8

6. Durable and maintenance free
7. Aesthetic in appearance
Disadvantages:
1. Very expensive system of wiring.
2. Requires good skilled workmanship.
3. Erection is quiet complicated and is time consuming.
4. Risk of short circuit under wet conditions (due to condensation of
water in tubes).
Specification of Wires:
The conductor material, insulation, size and the number of cores,
specifies the electrical wires. These are important parameters as they
determine the current and voltage handling capability of the wires. The
conductors are usually of either copper or aluminum. Various
insulating materials like PVC, TRS, and VIR are used. The wires may
be of single strand or multi strand. Wires with combination of different
diameters and the number of cores or strands are available.
For example: The VIR conductors are specified as 1/20, 3/22,….7/20
………
The numerator indicates the number of strands while the denominator
corresponds to the diameter of the wire in SWG (Standard Wire
Gauge). SWG 20 corresponds to a wire of diameter 0.914mm, while
SWG 22 corresponds to a wire of diameter 0.737 mm.
A 7/0 wire means, it is a 7-cored wire of diameter 12.7mm (0.5 inch).
The selection of the wire is made depending on the requirement
considering factors like current and voltage ratings, cost and
application.
Example: Application: domestic wiring
1. Lighting - 3/20 copper wire
2. Heating - 7/20 copper wire
The enamel coating (on the individual strands) mutually insulates the
strands and the wire on the whole is provided with PVC insulation. The
current carrying capacity depends on the total area of the wire. If cost
9

is the criteria then aluminum conductors are preferred. In that case, for
the same current rating much larger diameter of wire is to be used.
SWITCHES:
In electrical engineering, a switch is an electrical component that can
break an electrical circuit, interrupting the current or diverting it from
one conductor to another.
The most familiar form of switch is a manually operated
electromechanical device with one or more sets of electrical contacts,
which are connected to external circuits. Each set of contacts can be in
one of two states: either "closed" meaning the contacts are touching and
electricity can flow between them, or "open", meaning the contacts are
separated and the switch is nonconducting. The mechanism actuating
the transition between these two states (open or closed) can be either a
"toggle" (flip switch for continuous "on" or "off") or "momentary"
(push-for "on" or push-for "off") type.
A switch may be directly manipulated by a human as a control signal to
a system, such as a computer keyboard button, or to control power flow
in a circuit, such as a light switch. Automatically operated switches can
be used to control the motions of machines, for example, to indicate that
a garage door has reached its full open position or that a machine tool is
in a position to accept another work piece. Switches may be operated by
process variables such as pressure, temperature, flow, current, voltage,
and force, acting as sensors in a process and used to automatically
control a system. For example, a thermostat is a temperature-operated
switch used to control a heating process. A switch that is operated by
another electrical circuit is called a relay. Large switches may be
remotely operated by a motor drive mechanism. Some switches are used
to isolate electric power from a system, providing a visible point of
isolation that can be padlocked if necessary to prevent accidental
operation of a machine during maintenance, or to prevent electric
shock.
10

In circuit theory:
An ideal switch would have no voltage drop when closed, and would
have no limits on voltage or current rating. It would have zero rise time
and fall time during state changes, and would change state without
"bouncing" between on and off positions.
Practical switches fall short of this ideal, and have resistance, limits on
the current and voltage they can handle, finite switching time, etc. The
ideal switch is often used in circuit analysis as it greatly simplifies the
system of equations to be solved, however this can lead to a less accurate
solution. Theoretical treatment of the effects of non-ideal properties is
required in the design of large networks of switches, as for example
used in telephone exchanges.
Various Type OF Switches:
SPST:
Single Pole Single Throw: A simple on-off switch: The
two terminals are either connected together or
disconnected from each other. An example is a light
switch.
11

SPDT:
Single pole, double throw: A simple changeover switch:
C (COM, Common) is connected to L1 or to L2.
SPCO, SPTT:
Single Pole Change Over OR Single Pole Centre OFF
OR Single Pole Triple Throw: Similar to SPDT.
Some suppliers use SPCO/SPTT for switches with a
stable off position in the centre and SPDT for those
without.
12

DPST:
Double Pole Single Throw: Equivalent to two SPST
switches controlled by a single mechanism.
DPDT:
Double pole Double Throw: Equivalent to two SPDT
switches controlled by a single mechanism.
13

DPCO:
Double Pole Change Over OR Double Pole Centre OFF:
Equivalent to DPDT. Some suppliers use DPCO for
switches with a stable off position in the centre and
DPDT for those without.
INTERMEDIATE SWITCH:
DPDT switch internally wired for polarity-reversal
applications: only four rather than six wires are
brought outside the switch housing.
14

MANUFACTURING COMAPNIES:
ANCHOR SWITCHES:
15

AC POWER PLUG AND
SOCKETS:
AC power plugs and sockets are devices that allow electrically operated
devices to be connected to the primary alternating current (AC) power
supply in a building. Electrical plugs and sockets differ in voltage and
current rating, shape, size and type of connectors. The types used in
each country are set by national standards.
17

Generally the plug is the movable connector attached to an electrically
operated device's mains cable, and the socket is fixed on equipment or a
building structure. Plugs have male circuit contacts, while sockets have
female contacts. The plug has protruding prongs, blades, or pins that fit
into matching slots or holes in the socket. A socket is also called a
receptacle, outlet, or power point (British English). It may be
surrounded by a cover called a wall plate, face plate, outlet cover, socket
cover, or wall cover.
To reduce the risk of electric shock, plug and socket systems can
incorporate safety features. These may include socket design intended to
accept only compatible plugs inserted in the correct orientation; plugs
with insulated sleeves on contact pin shanks so a partially inserted plug
does not bear exposed live pins that could be touched; or sockets with
blocking shutters that open only when a compatible plug is inserted.
Sockets are designed to prevent exposure of bare live contacts. The
exposed contacts present in some sockets are used exclusively for
earthing (grounding).
ANCHOR SOCKETS:
HAVELLS SOCKET:
18

COMPARISON BETWEEN PRICE OF THREE
MANUFACTURING COMPANY:
Sr No.
ANCHOR
HAVELLS
WIPRO
COMMENTS
1.
2 PIN
16A/25
0V
SOCK
ET
Rs.332
6A 2 PIN
SOCK
ET
Rs.100
6A 2/3PIN
SOCK
ET
Rs.170
HAVELLS IS
BEST
FOR IT
LOW
PRICE
Sr No. ANCHOR HAVELLS WIPRO COMMENTS
1. 1-WAY
SWITCH
20A-250V
Rs.207
1-WAY
SWITCH
10A-250V
Rs.101
1-WAY
SWITCH
6A-250V
Rs.101
HAVELLS IS
BEST WITH
MEDIUM
RATING AND
RESONABLE
PRICE
2. 2-WAY
SWITCH
20A-250V
Rs.256
2-WAY
SWITCH
10A-250V
Rs.140
2-WAY
SWITCH
6A-250V
RS.122
WIPRO IS
BEST WITH
RESONABLE
PRICE
3. 1-WAY
SWITCH
WITH LED
20A-250V
Rs.247
1-WAY
SWITCH
WITH LED
10A-250V
Rs.140
1-WAY
SWITCH
WITH LED
6A-250V
Rs.133
AGAIN WIPRO
IS BEST WITH
RESONABLE
PRICE
4. 2-WAY
SWITCH
WITH LED
20A-250V
Rs.272
2-WAY
SWITCH
WITH LED
6A-250V
Rs.172
WIPRO IS
BEST WITH
RESONABLE
PRICE
19

2.
2 PIN +E
16A/250V
Rs.346
6A 3 PIN
SOCK
ET
Rs.141
6A 2 AND 3
PIN
SOCK
ET
Rs.240
HAVELLS IS
BEST
FOR IT
LOW
PRICE
3.
6A-16A
SOCK
ET
Rs.367
6-16A 3 PIN
SOCK
ET
Rs.230
6/16A 6 PIN
SOCK
ET
Rs.265
AGAIN
HAVEL
LS IS
BEST
FOR IT
LOW
PRICE
20

ELECTRICAL WIRING

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to ELECTRICAL WIRING (20)

Recently uploaded (20)

ELECTRICAL WIRING