Mc mp spa pack quick reference card

MC-MP SPA PACK
Gecko Alliance
• •

Three-Pump & Blower System With K-4-10K

Dual-Pump & Blower System With K-4-8K

The Quick Reference Card provides a quick overview of your spa's
main functions and the operations accessible with your digital control pad.

Starting Pump 1: Setting water temperature: Automatic water heater start:
Press Pump 1 to turn pump on at low speed Use Up or Down arrow key to increase or When water temperature is 1˚F (0.5˚C)
(for dual-speed pump). Pressing a second decrease water temperature. The tempera- lower than the Set Point, the heater will
time turns pump to high speed. A third time ture setting will be displayed for 5 seconds automatically turn on until water tempera-
turns pump off. A built-in timer automatically to confirm your new selection. ture reaches Set Point plus 1˚F (0.5˚C).
turns pump off after a predetermined period The "Set Point" symbol indicates The "Heater" icon lights up when
of time, unless manually deactivated first. the desired temperature, NOT the heater is on. It flashes when
1
The "Pump 1" icon lights up when the current water temperature! there is a request for more heat
pump is on at high speed. It flashes Water temperature can be adjusted by 1˚ in- but the heater has not yet started.
when pump is on at low speed. crements from 59 to 104˚F (15 to 40˚C).

Starting Pump 2:
Press Pump 2 to turn pump on at low speed
(for dual-speed pump). Pressing a second
time turns pump to high speed. A third time Programming filter cycles (K-4-10K)
turns pump off. A built-in timer automatically The system automatically performs two filter cycles per day, at 12-hour intervals. During a filter cycle,
turns pump off after a predetermined period Pumps 2 & 3 and blower run at high speed for one minute, then Pump 1 runs at low speed for a
of time, unless manually deactivated first. programmed number of hours and the ozonator is activated.
2
The "Pump 2" icon lights up when
pump is on at high speed. It flashes To set filter cycle duration and frequency:
when pump is on at low speed.

Starting Pump 3 (K-4-10K):
Press Pump 3 to turn pump on. Press a
second time to turn pump off. A built-in
timer automatically turns pump off after a
predetermined period of time, unless it has
been manually deactivated. Press Filter key. The Use Up or Down arrow When the desired setting Use Up or Down arrow
2
The "Pump 2" icon lights up when display will show Fdxx, key to change setting. is displayed, press Filter key to change setting
pump is on. with "xx" representing again. The display will (from 1 to 4, depending
the currently set filter 0 = no filtration show FFxx, with "xx" on selected duration).
cycle duration in hours. 12 = continuous representing the filter When the desired set-
Turning the light on: filtration cycle frequency per day. ting is displayed, press
Filter to confirm. The
Press Light to turn light on at high intensity. "Filter Cycle" icon lights
Press a second time to turn light to medium up when a filter cycle
intensity and a third time to turn light to low is on.
intensity. A fourth time turns light off. A built-in
timer automatically turns light off after 2 hours,
unless it has been manually deactivated. Troubleshooting
The "Light" icon lights up when light
is on at high intensity. It flashes when
light is on at medium or low intensity.
Fiber Box Option: If your spa is equipped with
an optional fiber box, press Light key to turn
fiber box (motor & light) on. Press a second
time to turn fiber box motor off and leave light
on. A third time turns both motor and light off.
The "Light" icon is displayed when fiber box Pumps have started up for Water temperature is 3 flashing dots are dis-
light is on. It flashes when motor and light are one minute on several oc- flashing. played.
on at the same time. A built-in timer automati- casions and "Filter Cycle"
icon is flashing. Water temperature in the A problem has been
cally turns fiber box off after 2 hours, unless spa has reached 112˚F detected.
manually deactivated first. Not a bug but a feature! (44˚C).
Do not enter the water!
Our Smart Winter Do not enter the water! Check and open water
Starting the blower: Mode protects your spa Allow water to cool down. valves. Clean filter if neces-
from the cold by automati- The system will reset auto- sary. Check water level.
Press Blower to turn blower on at high cally turning pumps on for matically when water tem- Add water if necessary.
speed. Press a second time to turn blower one minute several times a perature reaches 109˚F
to low speed. Pressing a third time turns day to prevent water from (43˚C). Shut power off and power
blower off. A built-in timer automatically freezing in pipes. your spa up again to reset
turns blower off after a predetermined Call your dealer or service the system.
period of time, unless it has been manually supplier if problem persists.
deactivated. Call your dealer or service
The display is flashing. supplier if problem persists.
The "Blower" icon lights up when
blower is on at high speed. It flashes A power failure has occurred.
when blower is on at low speed. Press any key to reset the
system.

Real-time clock (K-4-10K):
Use Clock to set real-time clock. The display
toggles every 5 seconds alternately showing
the hourly time and the current water tem-
perature. Quick Reference Card

http://www.MyPoolSpas.com Wholesale Pool and Spa Parts 920-925-3094

6
Temperature

Step
unit

Programming
Sequence
Step 1 Time of day
Step 2 Filter cycle start time
Step 3 Filter cycle duration
Step 4 Temperature unit
Filter Cycle Heater Up & Down
Step 5 Keypad lockout icon icon arrows
Step 6 Storing settings in memory Programming Mode Economy Mode
& returning to Normal mode icon icon Lock
icon

Step 1- Time of day (K-4-8K for Steps 1 to 6) Purge cycles (K-4-10K)
Setting the time: During a purge cycle, pumps and blower run for two minutes
and "Filter Cycle" icon lights up.
1- Enter Programming mode by holding
Prog. key pressed down for 2 seconds. Setting purge cycles:
10:25 am 2- The display will show the current setting. 1- Press Filter key.
11:43 pm 3- Use Up and Down arrows to change P 24 2- The display will show P xx, with "xx"
setting. representing the currently set number of
daily purge cycles.
P 20 3- Use Up and Down arrows to change setting.
Steps 2 & 3- Filter cycle start time & duration 4- Press Filter key to store settings.
The system automatically performs two filter cycles per day, at
12-hour intervals. During filter cycle, Pump 2 and blower run
for one minute. Pump 1 will then run at low speed for a pro- Inverted display (K-4-10K)
grammed number of hours. The "Filter Cycle" icon lights up
when a filter cycle is on. Press and hold Filter key for 5 seconds to invert the display.
If a power-up occurs, the display always returns to default
To program a filter cycle, you must enter: 1) the time you want mode.
the cycle to start and 2) the duration of the cycle. If no filtering is
required, the duration should be set to "0". For continuous
filtering, the filter cycle duration should be set to "12:00". Digital control pad lockout (K-4-10K & 8K)
Setting filter cycle start time: This function allows you to prevent unauthorized parameter
1- Press Prog. key a second time. setting of the unit. This feature is especially helpful when
young children have access to the keypad.
FS01 2- The display will show FSxx, with "xx"
representing the starting hour. There are two modes you can choose from: Full lock or
FS12 3- Use Up and Down arrows to change Partial lock. Full lock means that all keypad functions are
setting. locked. Partial lock means that the basic functions of the spa
will remain accessible (pumps, blower and light), but it will be
Setting filter cycle duration: impossible to change the temperature Set Point, to override
1- Press Prog. key a third time. the Economy mode or to enter the Programming mode.
Fd00 2- The display will show Fdxx, with "xx" When control pad is locked, the "Lock" icon will be displayed.
representing the duration in hours.
Locking your digital control pad:
Fd12 3- Use Up and Down arrows to change
setting. 1- Press and hold Pump 1 key for
5 seconds.
LocP 2- The display will show LocP, with "P"
Step 4- Temperature unit representing Partial lock.
LocF 3- Release key and keypad will be in
Water temperature can be displayed in either Fahrenheit (˚F) Partial lock mode. Keep key pressed
or Celsius (˚C). down for 5 more seconds if you want
to be in Full lock mode. The "LocF"
To display the temperature unit: message will then be displayed.
1- Press Prog. key a fourth time. When control pad is locked, all automatic functions of the
TU C 2- The display will show TU X, with "X" system run as usual. If a key is pressed down, a "LocP" or
for either ˚F or ˚C. "LocF" message will be displayed for 1 sec. To unlock the
TU F 3- Use Up and Down arrows to change keypad, simply press and hold Pump 1 key again for 5 sec.
setting.

Economy mode (K-4-10K & 8K)
Step 5- Keypad lockout
Press Econo key (or Mode key for K-4-8K keypad) to switch
To lock or unlock keypad: from Normal mode to Economy mode. To save energy, the
Economy mode Set Point is 20˚F (11˚C) below the Normal
1- Press Prog. key a fifth time. mode Set Point. The display toggles between the "Econ"
ULoc 2- The display will show "ULoc". message and the current temperature.
Loc 3- Use Up and Down arrows to change The "Economy Mode" icon lights up when Economy
setting. mode is on.

Step 6- Storing settings in memory Summary of control panel parameters
Press Prog. key a sixth time to store settings in the system's FSxx Filter cycle start time
non-volatile memory and to return to normal mode. Fdxx Filter cycle duration
P xx Purge cycles
Tu X Temperature unit
Temperature unit (K-4-10K & 8K) LocX Control pad lockout
Press and hold Light key for 5 seconds to toggle between
˚F and ˚C.

ITH GECKO'S EX
ED W CLU
IPP SIV
QU E•
•E

Smart
Winter
Mode
TM

3-85-7087-B 9919-100777

http://www.MyPoolSpas.com Wholesale Pool and Spa Parts 920-925-3094

Mc mp spa pack quick reference card

More Related Content

Similar to Mc mp spa pack quick reference card (20)

More from Accurate Pool & Spa Services, llc (20)

Mc mp spa pack quick reference card