Uc cf single-pump system quick reference card
0 likes177 views
The document provides a quick reference for operating a single-pump spa system. It outlines how to start and stop the pump, set the filter cycle duration from 2-6 hours, turn the light on and off and adjust its intensity, set the water temperature from 59-104°F, and troubleshoot issues with flashing error codes. The system automatically turns the pump and light off after 20 and 2 minutes respectively and has a smart winter mode to prevent freezing.
Uc cf single-pump system quick reference card
- 1. UC-CF Single-Pump System Gecko Alliance • • The Quick Reference Card provides a summary of Micro-SPA's main functions and a quick overview of the operations accessible from your topside keypad. Starting the pump: PROGRAMMING FILTER CYCLE DURATION Press Pump key to turn pump on at low The system automatically performs two filter cycles per day, at 12-hour intervals. During filter speed. Press a second time to turn pump cycle, the pump will be activated for a predetermined number of hours. This process also sets the to high speed (with a dual-speed pump). start time of the filter cycles, which will start up every 12 hours from the time the initial cycle has A third time turns pump off. A built-in been programmed. To set filter cycle duration: timer automatically turns pump off after 20 minutes, unless it has been manually deactivated. The "Pump" indicator lights up when pump is on at high speed. It flashes when pump is on at low speed. Turning the light on: Press and hold Light key for Use Up or Down arrows When the setting you want Press Light key to turn light on at high 5 seconds. The display will to change setting from is displayed, press Light key intensity. Subsequent presses will change show "Fxx", with "xx" 2 to 6 hours. again. The filter cycle will light intensity until it is turned off. A built-in representing the currently set start immediately. timer automatically turns light off after filter cycle duration in hours. 2 hours, unless it has been manually deactivated. 40-minute filter cycle time out: If you turn pump or light on during a filter cycle, the cycle The "Light" indicator is displayed will be interrupted and will only resume 40 minutes after you (or the system) have turned when light is on at high intensity. the last active output off. The "Filter Cycle" indicator will flash. It flashes when light is on at low intensity. TROUBLESHOOTING Setting water temperature: The pump has started up for one Not a bug but a feature! Press and hold Up or Down arrow key to minute on several occasions and set the current water temperature setting. "Filter Cycle" indicator is flashing. Our Smart Winter Mode protects The new and desired temperature ("Set your spa from the cold by automatically Point" value) setting will be displayed for turning the pump on for one minute several times a day to prevent water 5 seconds to confirm your new selection. from freezing in pipes. The "Set Point" indicator displays the desired temperature, NOT the current water temperature! 3 flashing dots are displayed. A problem has been detected. Do not enter the water! Check and Water temperature can be adjusted by open water valves. Clean filter if 1°F (0.5°C) increments from 59 to 104°F necessary. Check water level. (15 to 40°C). Add water if necessary. Shut power off and power your spa Automatic water heater start: up again to reset the system. When water temperature is 1˚F (0.5˚C) Call your dealer or service supplier if lower than the Set Point, the heater will problem persists. automatically turn on until water tempera- ture reaches Set Point plus 1˚F (0.5˚C). Water temperature is flashing. Water temperature in the spa has The "Heater" indicator lights up reached 112˚F (44˚C). when the heater is on. Do not enter the water! Allow water Note: If your system is configured in Low to cool down. The system will reset Current mode, the heater will not start automatically when water temperature if the pump is running at high speed. reaches 109˚F (43˚C). The "Heater" indicator will flash. Call your dealer or service supplier if problem persists. "r x.x" message is displayed. At power-up, the "r x.x" message is displayed for a few seconds, with "x.x" indicating the soft revision of your system. The display is flashing. A power failure has occurred. Press any key to stop the LED flashing, then reprogram filter cycle to adjust start time. French and Spanish versions available upon request. IPP ED W ITH GECKO'S EX CLU http://www.MyPoolSpas.com Wholesale Pool and Spa Parts 920-925-3094 SIV QU E• •E Smart Winter Mode TM 3-85-7071-B Quick Reference Card 9919-100544-B