NAHI Standards of Practice

STANDARDS OF PRACTICE

NATIONAL ASSOCIATION OF
HOME INSPECTORS, INC.

i


National Association of
Home Inspectors, Inc.

These Standards may not be reproduced without written permission
from the National Association of Home Inspectors, Inc.

© 1990 - 4.2006 edition.
4248 Park Glen Road
Minneapolis, Minnesota 55416
PHONE 952–928–4641 • FAX 952–929–1318

NATIONAL ASSOCIATION OF
HOME INSPECTORS, INC.

TABLE OF CONTENTS
1. Purpose, Scope & General Statements . . . . . . . . . . . . . . . . . . . 2
2. General Limitations & Exclusions . . . . . . . . . . . . . . . . . . . . . . 3
3. Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Foundations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5. Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
6. Roof Coverings, Flashings, Gutters,
Downspouts and Roof Ventilation . . . . . . . . . . . . . . . . . . . . . . 6
7. Roof Structure, Attic & Insulation . . . . . . . . . . . . . . . . . . . . . . 7
8. Attached Garage(s)/Carport(s) . . . . . . . . . . . . . . . . . . . . . . . . 8
9. Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
10. Plumbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
11. Central Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
12. Central Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
13. Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15


2

1. PURPOSE, SCOPE AND GENERAL
STATEMENTS
1.1 The Standards of Practice (Standards) provide the
minimum standards of performance for a written report
on a residential home inspection performed by and for
the exclusive use of members of the National Association
of Home Inspectors, Inc. (NAHI™). Use of the NAHI
logo and name is limited to those persons holding the
designation of Regular Member. Associate, NAHI CRI
and Affiliate Members may use specifically designated
logos in advertising.
1.2 The Standards define and clarify the purpose, conditions,
limitations, exclusions, and certain terms relating to an
inspection.
1.3 The Standards describe those items, components, and
systems included in the scope of an inspection.
1.4 The Standards apply only to the inspection of buildings
with one (1) to four (4) dwelling units.
1.5 The Standards apply to a visual inspection of the readily
accessible areas of the included items, components, and
systems to determine if, at the time of the inspection, they are
performing their intended function without regard to life
expectancy.
1.6 The purpose of the inspection is to identify visible defects
and/or conditions that, in the judgement of the inspector,
adversely affect the function and/or integrity of the items,
components, and systems.
1.7 Inspections performed under the Standards are basically
visual and rely upon the opinion, judgement, and
experience of the inspector, and are not intended to be
technically exhaustive.
1.8 Inspections shall be performed in a time period sufficient
to allow compliance with the provisions of the Standards.
1.9 Inspections performed under the Standards shall not be
construed as a compliance inspection of any code,
governmental regulation, or manufacturer’s installation
instructions or procedures. In the event a law, statute, or
ordinance prohibits a procedure recommended in the
Standards, the inspector is relieved of the obligation to
adhere to the prohibited part of the Standards.
1.10 Inspections performed under the Standards are not an
expressed or implied warranty or a guarantee of the
adequacy, performance, or useful life of any item,
component, or system in, on, or about the inspected
property.


3

1.11 Detached building(s) and detached garage(s) located on
the property will be inspected under these Standards
only if specifically listed in the inspection report.
1.12 The National Association of Home Inspectors, Inc.
recommends that its members perform inspections in
accordance with these Standards, the Code of Ethics,
and applicable law(s). The Standards are not intended
to limit members from performing “additional inspection
services.”
1.13 The inspector shall report on any system and component
included in these standards of practice which were
present at the time of the home inspection but were not
inspected and provide the reason they were not
inspected.

2. GENERAL LIMITATIONS AND EXCLUSIONS
2.1 Inspections performed under the Standards exclude any
item(s) concealed or not readily accessible to the
inspector. The inspector is not required to move
furniture, personal, or stored items; lift floor coverings;
move attached wall, ceiling coverings, or panels; or
perform any test(s) or procedures(s) which could
damage or destroy the item(s) being evaluated.
2.2 The following are excluded and not limited to:
appliances, recreational facilities, alarms, intercoms,
speaker systems, radio controlled devices, security devices
and lawn irrigation systems.
2.3 The determination of the presence of or damage caused
by termites or any other wood-damaging insects or
organism is excluded.
2.4 Also excluded from a standard home inspection is the
determination of the indoor air quality or sickness of any
building including, but not limited to, the presence or
absence of all manner of biological activity, such as
molds, insects, birds, pets, mammals, and other flora
and fauna, and their consequent physical damage,
toxicity, odors, waste products, and noxiousness.
2.5 Use of special instruments or testing devices, such as
amp meters, pressure gauges, moisture meters, gas
detectors and similar equipment is not required.
2.6 The inspection is not required to include information from
any source concerning previous property, geological,
environmental or hazardous waste conditions,
manufacturer recalls or conformance of proper
manufacturer’s installation of any component or system, or
information contained in Consumer Protection Bulletin.

4

The inspection is not required to include information from
any source concerning past or present violations of codes,
ordinances, or regulations.
2.7 The inspection and report are opinions only, based upon
visual observation of existing conditions of the inspected
property at the time of the inspection. THE REPORT
IS NOT INTENDED TO BE, OR TO BE
CONSTRUED AS, A GUARANTEE, WARRANTY,
OR ANY FORM OF INSURANCE. The inspector will
not be responsible for any repairs or replacements with
regard to the property or the contents thereof.
2.8 The inspector is not required to determine property
boundary lines or encroachments.
2.9 The inspector is not required to provide an inspection of
any condominium common component, system or
evaluate condominium reserve accounts.
2.10 The inspector is not required to enter any premises that
visibly shows a physical threat to the safety of the home
inspector or others nor inspect any area or component
that poses a danger to the inspector or others.

3. SITE

3.1 Components for Inspection.
3.1.1 Building perimeter, land grade, and water drainage
directly adjacent to the foundation.
3.1.2 Trees and vegetation that adversely affect the structure.
3.1.3 Walks, grade steps, driveways, patios, and retaining walls
contiguous with the structure.
3.2 Procedures for Inspection.
The inspector will:
3.2.1 Describe the type of material and inspect the condition of
the driveways, walkways, grade steps, patios, and other
items contiguous with the inspected structure.
3.2.2 Observe the drainage, grading, and vegetation for
conditions that adversely affect the structure.
3.3 Limitations.
The inspector is NOT required to:
3.3.1 Inspect fences or privacy walls.
3.3.2 Evaluate the condition of trees, shrubs, and or other
vegetation.
3.3.3 Evaluate or determine soil or geological conditions, site
engineering, or property boundaries.

5

4. FOUNDATIONS

4.1.1 Foundation walls, first-floor systems, other support and
sub-structure components, stairs.
4.1.2 Ventilation (when applicable).
4.1.3 Grade slab and/or floor slab.
The inspector will:
4.2.1 Describe the type of structure and material comprising
the structure and other items inspected.
4.2.2 Observe the condition and serviceability of visible,
exposed areas of foundation walls, grade slab, bearing
walls, posts, piers, beams, joists, trusses, subfloors,
chimney foundations, stairs, and other similar structural
components.
4.2.3 Inspect foundations for indications of flooding, moisture,
or water penetration.
4.2.4 Observe subfloor crawl space ventilation and vapor
barriers.
4.2.5 Operate the sump pump when present.
4.2.6 Inspect the visible and accessible wooden members.
4.2.7 Observe the visible condition of floor slab when present.
4.3 Limitations.
4.3.1 Enter subfloor crawl spaces with headroom of less than 3
feet, obstructions, or other detrimental conditions.
4.3.2 Move stored items or debris or perform excavation to
gain access.
4.3.3 Enter areas which, in the inspector’s opinion, may
contain conditions or materials hazardous to the health
and safety of the inspector.
4.3.4 Operate sump pumps equipped with internal/water
dependent switches.

5. EXTERIOR

5.1.1 Visible structural components.
5.1.2 Wall covering, trim, and protective coating.
5.1.3 Windows and doors.


6

5.1.4 Attached porches, decks, steps, balconies, handrails,
guardrails, and carports.
5.1.5 Visible exterior portions of chimneys.
The inspector will:
5.2.1 Describe the type and material comprising the exterior
components inspected.
5.2.2 Observe the condition of the components from the
ground level.
5.2.3 Observe the condition of a representative number of
visible windows and doors.
5.2.4 Inspect attached porches, decks, steps, balconies,
handrails, and guardrails.
5.3 Limitations.
5.3.1 Inspect buildings, decks, patios, retaining walls, and
other structures detached from the house.
5.3.2 Evaluate function of shutters, awnings, storm doors,
storm windows and similar accessories.
5.3.3 Inspect or test the operation of security locks, devices, or
systems.
5.3.4 Evaluate the presence, extent, and type of insulation and
vapor barriers in the exterior walls.
5.3.5 Examine the interior of the chimney flues or determine
the presence or absence of flue liners.
5.3.6 Inspect for safety type glass or the integrity of thermal
window seals or damaged glass.

6. ROOF COVERINGS, FLASHINGS, GUTTERS,
DOWNSPOUTS AND ROOF VENTILATION

6.1.1 Roof covering material.
6.1.2 Rain gutter and downspout system.
6.1.3 Visible portions of roof flashings.
6.1.4 Roof ventilation.
6.1.5 Roof soffits and fascias.
6.1.6 Roof skylights and other roof accessories.


7

The inspector will:
6.2.1 Describe the type of roofing and gutters.
6.2.2 Observe the condition of visible roof material, rain gutter
and downspout systems, visible portions of roof flashings,
roof soffits and fascias, roof vents, skylights and other
roof accessories visible from the exterior.
6.2.3 If possible, inspect the roof surface and components from
arms-length distance or with binoculars from the ground.
6.2.4 Inspect flat roofs where internal accessibility is readily
and safely available.
6.2.5 Report presence of roof ventilation.
6.3 Limitations.
6.3.1 Walk on or access a roof where it could damage the roof
or roofing material or be unsafe for the inspector.
6.3.2 Remove snow, ice, debris or other conditions that
prohibit the observation of the roof surfaces.
6.3.3 Inspect internal gutter and downspout systems and
related underground drainage piping.
6.3.4 Inspect antennas, lightning arresters, or similar
attachments.
6.3.5 Operate powered roof ventilators.
6.3.6 Determine remaining life expectancy of roof coverings,
presence or absence of hail damage; manufacturers’ defects,
exceptions, installation methods or recalls; or number of
layers.
6.3.7 Determine adequacy of roof ventilation.

7. ROOF STRUCTURE,ATTIC AND INSULATION

7.1.1 Roof framing, sheathing and decking.
7.1.2 Attic insulation.
The inspector will:
7.2.1 Describe the type of material comprising the roof
structure in the visible attic area.
7.2.2 Observe the condition of the visible roof structure and
attic components where readily and safely accessible.
7.2.3 Investigate evidence of the presence of water penetration.

8

7.2.4 Determine the presence of attic insulation and its
approximate thickness.
7.3 Limitations.
7.3.1 Enter attic spaces with headroom of less than 5 feet, with
insulation covering the ceiling joists, or bottom truss
chord, or if there are obstructions, trusses, or other
detrimental conditions.
7.3.2 Break or otherwise damage the surface finish or weather
seal on or around access panels and covers.

8.ATTACHED GARAGE(S)/CARPORT(S)

8.1.1 Exterior and interior walls and ceilings, floors, windows,
doors, roof, and foundation.
8.1.2 Electrical system and components.
8.1.3 Plumbing system and components.
8.1.4 Heating systems or units.
The inspector will:
8.2.1 Describe the type and material of door(s), exterior walls,
roof (if applicable), and other items to be inspected.
8.2.2 Observe the condition and function of listed components;
electric, plumbing, heating and similar systems.
8.2.3 Inspect vehicle doors for type, general condition, and
intended function by manual operation or by the use of
permanently affixed opener(s).
8.3 Limitations.
8.3.1 Inspect or operate equipment housed in the garage area
except as otherwise addressed in the Standards.
8.3.2 Verify or certify safe operation of any auto reverse or related
safety function(s) of a vehicle door.

9. ELECTRICAL

9.1.1 Entrance of the primary service from masthead to main
panel.
9.1.2 Main and sub-panels including feeders.


9

9.1.3 Branch circuits, connected devices, and lighting fixtures.
The inspector will:
9.2.1 Describe the type and location of primary service
(overhead or underground), voltage, amperage, and
over-current protection devices (fuses or breakers).
9.2.2 Observe the existence of a connected grounding
conductor when readily accessible.
9.2.3 Inspect the main and branch circuit conductors for
proper over-current protection and condition by visual
observation after removal of the readily accessible main
and sub electric panel cover(s).
9.2.4 Report the presence of aluminum branch circuit wiring at
the main and sub-panels.
9.2.5 Verify operation of a representative number of accessible
switches, receptacles and light fixtures.
9.2.6 Verify grounding and polarity of a representative number
of receptacles in proximity to plumbing fixtures or on the
exterior.
9.2.7 Verify operation of ground fault circuit interrupters
(GFCI), if present.
9.2.8 Observe the general condition of visible branch circuit
conductors that may constitute a hazard to the occupant
or the structure by reason of improper use or installation
of electrical components.
9.3 Limitations.
9.3.1 Insert any tool, probe or testing device into the main or
sub-panels.
9.3.2 Activate electrical systems or branch circuits which are
not energized.
9.3.3 Operate overload protection devices.
9.3.4 Inspect ancillary systems, including but not limited to:
burglar alarms, home protection systems, low voltage
relays, smoke/heat detectors, antennas, electrical de-icing
tapes, lawn sprinkler wiring, swimming pool wiring, or
any systems controlled by timers.
9.3.5 Move any objects, furniture, or appliances to gain access
to any electrical component.
9.3.6 Test every switch, receptacle, and fixture.
9.3.7 Remove switch and outlet cover plates.


10

9.3.8 Inspect electrical equipment not readily accessible or
dismantle any electrical device or control.
9.3.9 Verify continuity of connected service ground(s).

10. PLUMBING
10.1.1 Visible water supply lines.
10.1.2 Visible waste/soil and vent lines.
10.1.3 Fixtures and faucets.
10.1.4 Domestic hot water system and fuel source.
The inspector will:
10.2.1 Describe the material of the main line and water supply
lines.
10.2.2 Verify the presence of a main water supply valve.
10.2.3 Describe the type of sanitary waste piping.
10.2.4 Describe the type and capacity of domestic water
heating unit(s).
10.2.5 Inspect the condition of accessible and visible water
and waste lines.
10.2.6 Inspect and operate fixtures and faucets.
10.2.7 Inspect and operate the domestic hot water system.
10.2.8 Inspect and operate drain pumps and waste ejector
pumps when possible.
10.2.9 Test the water supply for functional flow.
10.2.10 Test waste lines from sinks, tubs and showers for
functional drainage.
10.3 Limitations.
10.3.1 Operate any main, branch or fixture valve, except
faucets, or determine water temperature.
10.3.2 Inspect any system that is shut-down or secured.
10.3.3 Inspect any plumbing components not readily
accessible.
10.3.4 Inspect any exterior plumbing components or interior
or exterior drain systems.
10.3.5 Inspect interior fire sprinkler systems.
10.3.6 Evaluate the potability of any water supply.


11

10.3.7 Inspect water conditioning equipment, including
softener and filter systems.
10.3.8 Operate freestanding or built-in appliances.
10.3.9 Inspect private water supply systems.
10.3.10 Test shower pans, tub and shower surrounds, or
enclosures for leakage.
10.3.11 Inspect gas supply system for materials, installation or
leakage.
10.3.12 Evaluate the condition and operation of water wells
and related pressure tanks and pumps; the quality or
quantity of water from on-site water supplies; or the
condition and operation of on-site sewage disposal
systems such as cesspools, septic tanks, drain fields,
related underground piping, conduit, cisterns, and
equipment.
10.3.13 Inspect and operate fixtures and faucets if the flow end
of the faucet is connected to an appliance.
10.3.14 Record location of any on-site visible fuel tanks within
or directly adjacent to structure.

11. CENTRAL HEATING

11.1.1 Fuel source.
11.1.2 Heating equipment.
11.1.3 Heating distribution.
11.1.4 Operating controls.
11.1.5 Flue pipes, chimneys and venting.
11.1.6 Auxiliary heating units.
The inspector will:
11.2.1 Describe the type of fuel, heating equipment, and
heating distribution system.
11.2.2 Operate the system using normal readily accessible
control devices.
11.2.3 Open readily accessible access panels or covers
provided by the manufacturer or installer, if readily
detachable.
11.2.4 Observe the condition of normally operated controls
and components of the systems.
11.2.5 Observe visible flue pipes, dampers and related
components for functional operation.

12

11.2.6 Observe the condition of a representative number of
heat sources in each habitable space of the house.
11.2.7 Inspect the operation of fixed supplementary heat
units. See 2.6 for more information.
11.3 Limitations.
11.3.1 Activate or operate heating or other systems that do
not respond to normal controls or have been shut-
down.
11.3.2 To inspect or evaluate a heat exchanger.
11.3.3 Inspect equipment or remove covers or panels that are
not readily accessible.
11.3.4 Dismantle any equipment, controls, or gauges.
11.3.5 Inspect the interior of chimney flues.
11.3.6 Inspect heating system accessories, such as
humidifiers, air purifiers, motorized dampers, heat
reclaimers, etc.
11.3.7 Inspect solar heating systems.
11.3.8 Activate heating, heat pump systems, or other systems
when ambient temperatures or other circumstances are
not conducive to safe operation or may damage the
equipment.
11.3.9 Evaluate the type of material contained in insulation
and/or wrapping of pipes, ducts, jackets and boilers.
11.3.10 Operate digital-type thermostats or controls.
11.3.11 Evaluate the capacity, adequacy, or efficiency of a
heating or cooling system.
11.3.12 Test or operate gas logs, built-in gas burning
appliances, grills, stoves, space heaters, or solar
heating devices.
11.3.13 Determine clearance to combustibles or adequacy of
combustion air.

12. CENTRAL AIR CONDITIONING

12.1.1 Cooling equipment.
12.1.2 Cooling distribution.
12.1.3 Operating controls.


13

The inspector will:
12.2.1 Describe the type of central air conditioning system
and energy sources.
12.2.2 Operate the system using normal control devices.
12.2.3 Open readily accessible access panels or covers
provided by the manufacturer or installer, if readily
accessible.
12.2.4 Observe the condition of controls and operative
components of the complete system, conditions
permitting.
12.2.5 Observe the condition of a representative number of the
central air cooling outlets in each habitable space of the
house.
12.3 Limitations.
12.3.1 Activate or operate cooling or other systems that have
been shut-down.
12.3.2 Inspect gas-fired refrigeration systems, evaporative
coolers, or wall or window-mounted air conditioning
units.
12.3.3 Check the pressure of the system coolant or determine
the presence of leakage.
12.3.4 Evaluate the capacity, efficiency, or adequacy of the
system.
12.3.5 Operate equipment or systems if exterior temperature
is below 60° Fahrenheit or when other circumstances
are not conducive to safe operation or may damage the
equipment.
12.3.6 Remove covers or panels that are not readily
accessible.
12.3.7 Dismantle any equipment, controls, or gauges.
12.3.8 Check the electrical current drawn by the unit.
12.3.9 Operate digital-type thermostats or controls.

13. INTERIOR

13.1.1 Walls, ceilings, floors, windows, and doors.
13.1.2 Steps, stairways, balconies, railings.
13.1.3 Fireplaces.


14

13.1.4 Electric outlets and fixtures.
13.1.5 Plumbing fixtures and components.
13.1.6 Heating and cooling distribution.
The inspector will:
13.2.1 Observe the visible condition of the surfaces of walls,
ceilings, and floors relative to structural integrity and
evidence of water penetration.
13.2.2 Verify the presence of steps, stairways, balconies,
handrails and guardrails and observe their condition.
13.2.3 Describe type, material, condition and operation of a
representative number of windows, doors and their
hardware.
13.2.4 Inspect the exterior condition of the kitchen cabinets
and countertops.
13.2.5 Observe the condition of fireplaces, dampers, fire
boxes and hearths readily visible.
13.2.6 Locate and observe a representative number of
electrical outlets/fixtures and wiring in each room as
described in Section 9.
13.2.7 Comment on presence or absence of smoke detectors.
13.2.8 Observe condition and operation of plumbing fixtures
and components in each room as described in Section
10.
13.3 Limitations.
13.3.1 Ignite fires in a fireplace or stove to determine the
adequacy of draft, perform a chimney smoke test, or
inspect any solid fuel device in use.
13.3.2 Evaluate the installation or adequacy of inserts, wood
burning stoves, or other modifications in a fireplace,
stove, or chimney.
13.3.3 Determine clearance to combustibles in concealed
areas.
13.3.4 Determine cosmetic condition of ceilings, walls, floor
coverings, and components.
13.3.5 Determine if the bath and/or kitchen vent fan ducting
exhausts air to exterior of house.


15

GLOSSARY OF TERMS

Activate: To turn on, supply power, or enable systems, equipment,
or devices to become active by normal control means. Examples
include turning on the gas or water supply valves to the fixtures and
appliances and activating electrical breakers or fuses.
Additional Inspection Services: Those services offered in
addition to the home inspection as defined in these standards,
including but not limited to the following examples; wood
destroying insect-organism and environmental testing.
Adversely Affect: Constitute, or potentially constitute, a negative
or destructive impact.
Appliance: A household device operated by use of electricity or
gas. Not included in this definition are components covered under
central heating, central cooling, or plumbing.
Detrimental Conditions: Any conditions that, in the opinion of
the inspector, may likely be unsafe, unhealthy, or in any way harmful
to the inspector or to components of the property.
Describe: To distinguish from another system or component.
Evaluate: To ascertain, judge, or form an opinion about an item or
condition.
Foundation: The base upon which the structure or a wall rests;
usually masonry, concrete, or stone, and generally partially
underground.
Function: The action for which an item, component or system is
specially fitted or used or for which an item, component or system
exists; to be in action or perform a task.
Functional: Performing, or able to perform, a function.
Functional Drainage: A drain is functional when it empties in a
reasonable amount of time and is not subject to overflow when one of
its supply faucets is left on.
Functional Flow: Sufficient water flow to provide uninterrupted
supply to the highest, unrestricted tap (faucet furthest from the
source) when a single intermediate, unrestricted tap is operated
simultaneously with uninterrupted flow.
Habitable: In a condition suitable for human habitation.
Habitable Spaces: Rooms or spaces used for sitting, sleeping,
bathing, toilets, eating or cooking. Not considered habitable spaces by
these Standards are closets, halls, storage spaces and utility areas.


16

Heat Source: A heat source may be a radiator, convector unit,
radiant panel, heat pipe, ductwork, grille, register, or other device(s)
from which heat is intended to be emitted.
Home Inspection: The process by which an inspector visually
examines the readily accessible systems and components of a home
and operates those systems and components utilizing the Standards of
Practice as a guideline.
Inspect: To evaluate carefully without use of technically exhaustive
methods.
Inspected Property: The readily accessible areas of the
buildings, site, items, components, and systems included in the
inspection.
Intended Function: Performing or able to perform the usual
function for which an item is designed, or fitted; and be in a condition
(state of repair) appropriate to this function, its age and location.
[See Function]
Observe: To see through visual directed attention.
Operate: To cause equipment or systems that have been activated to
perform their intended function(s), such as turning on a water faucet
or turning up the thermostat on an activated heating system.
Readily Accessible: An item or component is readily accessible
if, in the judgement of the inspector, it is capable of being safely
observed without movement of obstacles, detachment or
disengagement of connecting or securing devices, or other unsafe or
difficult procedures to gain access.
Representative Number: A sufficient number to serve as a
typical or characteristic example of the item(s) inspected.
Shut-down: A system or equipment is considered to be shut-down
when its normal control device(s) will not cause it to become activated
or operational. The inspector is not required to activate or operate
safety devices (fuses, breakers, etc.) in the “off ” position. It is not the
responsibility of the inspector to put these controls in the “on” mode,
nor to ensure that the equipment or systems to be tested are operable
at the time of the inspection.
Slab on Grade: Structures that have no crawl space and are in
direct contact with the soil. Slabs may or may not have supporting
piers or pads.
Technically exhaustive: An inspection is technically exhaustive
when it involves the use of measurements, instruments, testing
calculations and other means to develop scientific or engineering
findings, conclusions, and recommendations.
Verify: To confirm or substantiate.


4248 Park Glen Road
Minneapolis, Minnesota 55416
TOLL FREE PHONE 800-448-3942
PHONE 952-928-4641
FAX 952-929-1318
www.nahi.org

April 2006

NAHI Standards of Practice

More Related Content

Similar to NAHI Standards of Practice (20)

More from commercialnetinc (8)

Recently uploaded (20)

NAHI Standards of Practice