oscillatorsFGJJOPJOPJGFPOJGPJPFJPJPOJPO.ppt

Objectives
 Describe the basic concept of an oscillator
 Discuss the basic principles of operation of an
oscillator
 Analyze the operation of RC and LC oscillators
 Describe the operation of the basic relaxation
oscillator circuits

Introduction
 Oscillator is an electronic circuit that generates a
periodic waveform on its output without an
external signal source. It is used to convert dc to ac.
 Oscillators are circuits that produce a continuous
signal of some type without the need of an input.
 These signals serve a variety of purposes.
 Communications systems,
 digital systems (including computers), and
 test equipment make use of oscillators

Introduction
 An oscillator is a circuit that produces a repetitive signal from
a dc voltage.
 The feedback oscillator relies on a positive feedback of the
output to maintain the oscillations.
 The relaxation oscillator makes use of an RC timing circuit to
generate a nonsinusoidal signal such as square wave
Sine wave
Square wave
Sawtooth wave

Types of oscillators
1. RC oscillators
 Wien Bridge
 Phase-Shift
2. LC oscillators
 Hartley
 Colpitts
 Crystal
3. Unijunction / relaxation oscillators

Feedback Oscillator Principles
 When switch at the amplifier input is open, no oscillation occurs.
 Consider Vi,, results in Vo=AVi (after amplifier stage) and Vf = (AVi)
(after feedback stage)
 Feedback voltage Vf = (AVi) where A is called loop gain.
 In order to maintain Vf = Vi , A must be in the correct magnitude and
phase.
 When the switch is closed and Vi is removed, the circuit will continue
operating since the feedback voltage is sufficient to drive the amplifier and
feedback circuit, resulting in proper input voltage to sustain the loop
operation.
Feedback circuit used as an oscillator

Basic principles for oscillation
 An oscillator is an amplifier with positive feedback.
A

V e
V f
V s
V o
+
(1)
f
s
e V
V
V 

(2)
o
f βV
V 
    (3)
o
s
f
s
e
o βV
V
A
V
V
A
AV
V 





 The closed loop gain is:
   
o
s
f
s
e
o
βV
V
A
V
V
A
AV
V





o
s
o V
A
AV
V 


  s
o AV
V
A 
 
1
 
Aβ
A
V
V
A
s
o
f



1

 In general A and  are functions of frequency and
thus may be written as;
is known as loop gain
     
   
s
β
s
A
1
s
A
s
V
V
s
A
s
o
f



   
s
β
s
A

 Writing the loop gain becomes;
 Replacing s with j
 and
     
s
s β
A
s
T 
   
 
s
T
1
s
A
s
Af


   
 
jω
T
1
jω
A
jω
Af


     
jω
β
jω
A
jω
T 

 At a specific frequency f0
 At this frequency, the closed loop gain;
will be infinite, i.e. the circuit will have finite output
for zero input signal - oscillation
      1
0
0
0 
 jω
β
jω
A
jω
T
   
   
0
0
0
0
jω
β
jω
A
1
jω
A
jω
Af



 Thus, the condition for sinusoidal oscillation of
frequency f0 is;
 This is known as Barkhausen criterion.
 The frequency of oscillation is solely determined by
the phase characteristic of the feedback loop – the
loop oscillates at the frequency for which the phase
is zero.
    1
0
0 
jω
β
jω
A

 The feedback oscillator is widely used for
generation of sine wave signals.
The positive (in phase) feedback arrangement
maintains the oscillations.
The feedback gain must be kept to unity to keep the
output from distorting.

In phase
Noninverting
amplifier
V f V o
A v
Feedback
circuit

Design Criteria for Oscillators
1. The magnitude of the loop gain must be unity or
slightly larger
– Barkhaussen criterion
2. Total phase shift, of the loop gain mus t be 0 ° or
360°
1

Aβ

RC Oscillators
 RC feedback oscillators are generally limited to
frequencies of 1 MHz or less.
 The types of RC oscillators that we will discuss are
the Wien-bridge and the phase-shift

Wien-bridge Oscillator
 It is a low frequency oscillator which ranges from a
few kHz to 1 MHz.

Working of Wein bridge Oscillator
The feedback signal in this oscillator circuit is connected to the non-inverting input
terminal so that the op-amp works as a non-inverting amplifier.
The condition of zero phase shift around the circuit is achieved by balancing the
bridge, zero phase shift is essential for sustained oscillations.
The frequency of oscillation is the resonant frequency of the balanced bridge and is
given by the expression fo = 1/2πRC
At resonant frequency ( ƒo), the inverting and non-inverting input voltages will be
equal and “in-phase” so that the negative feedback signal will be cancelled out by
the positive feedback causing the circuit to oscillate.
From the analysis of the circuit, it can be seen that the feedback factor β= 1/3 at the
frequency of oscillation. Therefore for sustained oscillation, the amplifier must have a
gain of 3 so that the loop gain becomes unity.
For an inverting amplifier the gain is set by the feedback resistor network Rf and Ri
and is given as the ratio -Rf/Ri.

 The loop gain for the oscillator is;
 where;
 and;
      



















s
p
p
Z
Z
Z
R
R
s
β
s
A
s
T
1
2
1
sRC
R
Zp


1
sC
sRC
Zs


1

 Hence;
 Substituting for s;
 For oscillation frequency f0;
 
 

















RC
/j
RC
j
R
R
j
T
0
0
1
2
0
1
3
1
1



 
 

















/sRC
sRC
R
R
s
T
1
3
1
1
1
2
 
 

















RC
/j
RC
j
R
R
j
T



1
3
1
1
1
2

 Since at the frequency of oscillation, T(j) must be
real (for zero phase condition), the imaginary
component must be zero;
 Which gives us;
0
1
0
0 

RC
j
RC
j


RC
1
0 


 From the previous equation;
 the magnitude condition is;
or
















3
1
1
1
1
2
R
R
 
 

















RC
/j
RC
j
R
R
j
T
0
0
1
2
0
1
3
1
1



2
1
2

R
R
To ensure oscillation, the ratio R2/R1 must be
slightly greater than 2.

 With the ratio;
 then;
K = 3 ensures the loop gain of unity – oscillation
 K > 3 : growing oscillations
 K < 3 : decreasing oscillations
2
1
2

R
R
3
1
1
2



R
R
K

Design
The required frequency of oscillation
fo=1kHz
we have,
Take C=0.01µF, then R=1.6kΩ (Use 1.5kΩ
standard)
Gain of the amplifier section is given by,
Take Ri=1kΩ, then Rf=2.2kΩ
(Use 4.7kΩ Potentio meter for fine
corrections)

Phase-Shift Oscillator
.
C C C
R R
R
Rf
+

Vo
0 V
Phase-shift oscillator
 The phase shift oscillator utilizes three RC circuits to
provide 180º phase shift that when coupled with the 180º of
the op-amp itself provides the necessary feedback to
sustain oscillations.

 The frequency for this type is similar to any RC circuit oscillator :
6
2
1
RC
f


where  = 1/29 and the phase-shift is 180o
 For the loop gain A to be greater than unity, the gain of the amplifier
stage must be greater than 29.
 If we measure the phase-shift per RC section, each section would not
provide the same phase shift (although the overall phase shift is 180o).
 In order to obtain exactly 60o phase shift for each of three stages,
emitter follower stages would be needed for each RC section.
The gain must be at least 29 to maintain the oscillation

The transfer function of the RC network is

If the gain around the loop equals 1, the circuit oscillates at this
frequency. Thus for the oscillations we want,
Putting s=jω and equating the real parts and imaginary parts,
we obtain

From equation (1) ;
Substituting into equation (2) ;
# The gain must be at least 29 to maintain the oscillations.

Phase Shift Oscillator – Practical
RC
fr

2
6
 29
1
2


R
R
K

Design
Frequency of oscillation (F):
Gain of the Op Amp inverting amplifier (G):
Attenuation offered by the feedback RC
network is 1/29, so the gain of inverting
amplifier should be 29
Use Ri=1.2 KΩ
So, Rf=35KΩ
Use 50KΩ potentiometer and adjust its
value to obtain output on CRO

RC
fr
6
2
1

 29
3




R
R
K
f
The last R has been incorporated into the summing resistors
at the input of the inverting op-amp.

LC Oscillators
 Use transistors and LC tuned circuits or crystals in
their feedback network.
 For hundreds of kHz to hundreds of MHz frequency
range.
 Examine Colpitts, Hartley and crystal oscillator.

Colpitts Oscillator
 The Colpitts oscillator is a type
of oscillator that uses an LC
circuit in the feed-back loop.
The feedback network is made
up of a pair of tapped
capacitors (C1 and C2) and an
inductor L to produce a
feedback necessary for
oscillations.
The output voltage is
developed across C1.
The feedback voltage is
developed across C2.

Colpitts Oscillator
 KCL at the output node:
 voltage divider produces:
 substitute eq(2) into eq(1):
0
1
1
2
1





sC
sL
V
V
g
R
V
sC
V o
gs
m
o
o
o
gs V
sL
sC
sC
V 














2
2
1
1
  0
1
1 1
2
2
2 















 sC
R
LC
s
sC
g
V m
o
- Eq (1)
- Eq (2)

Colpitts Oscillator
 Assume that oscillation has started, then Vo≠0
 Let s=jω
 both real & imaginary component must be zero
 Imaginary component:
  0
1
2
1
2
2
2
1
3












R
g
C
C
s
R
LC
s
C
LC
s m
 
  0
1
2
1
2
2
1
2
2













 C
LC
C
C
j
R
LC
R
gm 












2
1
2
1
1
C
C
C
C
L
o

- Eq (3)

Colpitts Oscillator
 both real & imaginary component must be zero
 Imaginary component:
 Combining Eq(3) and Eq(4):
 to initiate oscillations spontaneously:
R
g
R
LC
m
1
2
2



R
g
C
C
m

1
2









1
2
C
C
R
gm
- Eq (4)

Hartley Oscillator
 The Hartley oscillator is
almost identical to the
Colpitts oscillator.
 The primary difference
is that the feedback
network of the Hartley
oscillator uses tapped
inductors (L1 and L2) and
a single capacitor C.

Hartley Oscillator
 the analysis of Hartley oscillator is identical to that
Colpitts oscillator.
 the frequency of oscillation:
 C
L
L
o
2
1
1




Crystal Oscillator
 Most communications and digital applications require the
use of oscillators with extremely stable output. Crystal
oscillators are invented to overcome the output fluctuation
experienced by conventional oscillators.
Crystals used in electronic applications consist of a quartz
wafer held between two metal plates and housed in a a
package as shown in Fig. 9 (a) and (b).

Crystal Oscillator
 Piezoelectric Effect
 The quartz crystal is made of silicon oxide (SiO2) and
exhibits a property called the piezoelectric
 When a changing an alternating voltage is applied across
the crystal, it vibrates at the frequency of the applied
voltage. In the other word, the frequency of the applied ac
voltage is equal to the natural resonant frequency of the
crystal.
 The thinner the crystal, higher its frequency of vibration.
This phenomenon is called piezoelectric effect.

Crystal Oscillator
 Characteristic of Quartz
Crystal
 The crystal can have two resonant
frequencies;
 One is the series resonance frequency f1
which occurs when XL = XC. At this
frequency, crystal offers a very low
impedance to the external circuit where
Z = R.
 The other is the parallel resonance (or
antiresonance) frequency f2 which
occurs when reactance of the series leg
equals the reactance of CM. At this
frequency, crystal offers a very high
impedance to the external circuit
R
L
C
CM

Crystal Oscillator
 The crystal is connected as a series element in the
feedback path from collector to the base so that it is
excited in the series-resonance mode
BJT
FET

Crystal Oscillator
 Since, in series resonance, crystal impedance is the smallest that
causes the crystal provides the largest positive feedback.
 Resistors R1, R2, and RE provide a voltage-divider stabilized dc bias
circuit. Capacitor CE provides ac bypass of the emitter resistor, RE
to avoid degeneration.
 The RFC coil provides dc collector load and also prevents any ac
signal from entering the dc supply.
 The coupling capacitor CC has negligible reactance at circuit
operating frequency but blocks any dc flow between collector and
base.
 The oscillation frequency equals the series-resonance frequency of
the crystal and is given by:
C
o
LC
f

2
1


Unijunction Oscillator
 The unijunction transistor
can be used in what is
called a relaxation oscillator
as shown by basic circuit as
follow.
The unijunction oscillator
provides a pulse signal
suitable for digital-circuit
applications.
Resistor RT and capacitor CT
are the timing components
that set the circuit
oscillating rate
UJT

 Sawtooth wave
appears at the emitter
of the transistor.
This wave shows the
gradual increase of
capacitor voltage

 The oscillating frequency is calculated as follows:
 where, η = the unijunction transistor intrinsic stand-
off ratio
 Typically, a unijunction transistor has a stand-off
ratio from 0.4 to 0.6
 
 



1
/
1
ln
1
T
T
o
C
R
f

oscillatorsFGJJOPJOPJGFPOJGPJPFJPJPOJPO.ppt

More Related Content

Similar to oscillatorsFGJJOPJOPJGFPOJGPJPFJPJPOJPO.ppt (20)

Recently uploaded (20)

oscillatorsFGJJOPJOPJGFPOJGPJPFJPJPOJPO.ppt