Point To Point Protocol
Download as PPTX, PDF19 likes17,422 views
The document discusses Point-to-Point Protocol (PPP), which provides a standard method for transporting multi-protocol datagrams over point-to-point links. PPP consists of encapsulating packets into frames, a Link Control Protocol (LCP) for establishing and configuring the connection, and Network Control Protocols (NCPs) for network layer configuration. It describes PPP frame formats, byte stuffing for transparency, and authentication protocols like PAP and CHAP. The presentation includes a Wireshark demo and addresses questions about PPP design requirements and non-requirements.
Point To Point Protocol
- 1. Point to Point Protocol PRESENTER: PHAN DINH VUONG INSTRUCTOR: PROF.DR.FRIEDBERT KASPAR
- 2. Agenda What is PPP? Design Requirements Data frame format Byte stuffing Control Protocol Wireshark Demo Q&A
- 3. OSI Model
- 4. What is Point-to-Point Protocol ? What is the difference between point to point and peer to peer? Answer: - Point to point is a protocol for communication between two computers using a serial interface (phone). - Peep to peer (P2P) is a communication model in which each party has the same capabilities and either party can initiate a communication session (BitTorrent).
- 5. What is Point-to-Point Protocol ? The Point-to-Point Protocol (PPP) provides a standard method for transporting multi-protocol datagrams over point-to-point links. PPP is comprised of three main components: • A method for encapsulating multi-protocol datagrams. • A Link Control Protocol (LCP) for establishing, configuring, and testing the data-link connection. • A family of Network Control Protocols (NCPs) for establishing and configuring different network-layer protocols.
- 6. Design requirements? • Packet framing: Packet (from network-layer) Frames (start & end of frame) • Transparency.To network layer packet (headers or data). • Multiple network layer protocols. Able to support multiple network layer protocols (e.g., IP, RIP, ICMP) running over the same physical link at the same time. • Multiple types of links. Operate over a wide variety of link types: serial or parallel, synchronous or asynchronous, low speed or high speed, electrical or optical. • Error detection. Able to detect bit errors in the received frame. • Connection liveness: detect a failure at the link level (e.g., the inability to transfer data from the sending side of the link to the receiving side of this link) and signal this error condition to the network layer. • Network Layer Address Negotiation. mechanism for the communicating network layers (e.g., IP) to learn or configure each other's network layer address. • Simplicity.The first and foremost among all requirements . RFC 1547 states "the watchword for a point-to-point protocol should be simplicity."
- 7. Design Non-requirements? • Error correction. Required to detect bit errors but is NOT required to correct • Flow control. receive frames at the full rate of the underlying physical layer .NO need to control for upper layers • Sequencing. NOT required to deliver frames in the same order • Multipoint links. Only a single sender and a single receiver.
- 8. Data frame format 01111110 11111111 00000011 Protocol Info Padding Check 01111110 • Flag: delimiter (framing) • Address: not used in PPP as no support addressing(used in HDLC broadcast address) • Control: always 00000011, transmission not sequenced, connectionless link. • Protocol: upper layer protocol to which frame delivered (eg,IP 0x0021, IPX 0x002B) • Info: upper layer data being carried • Padding: In some cases, additional dummy bytes may be added to pad out the size of the PPP frame. • Check: cyclic redundancy check for error detection (2 0r 4 bytes, default 2 bytes) Flag FlagAddress Control 1 byte 1 byte 1 byte 1 or 2 byte Variable length 2 or 4 bytes 1 byte Variable length
- 9. Stuffing • Question: if receive <01111110> => It is data or flag? • Sender: adds (“stuffs”) extra < 01111110> byte after each < 01111110> data byte • Receiver: - two 01111110 bytes in a row: discard first byte, continue data reception - single 01111110: flag byte PPP PPP A5 BB 01111110 B4 B4 01111110 BB A5 A5 BB 01111110 01111110 B4
- 10. Control Protocol
- 11. Authentication Value (in hex) Protocol • c023 Password Authentication Protocol (PAP) • c223 Challenge Handshake Authentication Protocol (CHAP)
- 12. Password Authentication Protocol (PAP)
- 13. Challenge Handshake Authentication Protocol(CHAP)
- 14. Wireshark Demo
- 15. Frame format
- 18. Q&A
- 19. Thank you!
- 20. References • http://www-ee.uta.edu/online/wang/ppp.pdf • Wikipedia: http://en.wikipedia.org/wiki/PPP • RFC 1661: http://www.ietf.org/rfc/rfc1661.txt
Editor's Notes
- #7: RIP, Routing Information ProtocolICMP, Internet Control Message Protocol
- #11: Link Dead: This phase occurs when the link fails, or one side has been told to disconnect (e.g. a user has finished his or her dialup connection.)Link Establishment Phase: This phase is where Link Control Protocol negotiation is attempted. If successful, control goes either to the authentication phase or the Network-Layer Protocol phase, depending on whether authentication is desired.Authentication Phase: This phase is optional. It allows the sides to authenticate each other before a connection is established. If successful, control goes to the network-layer protocol phase.Network-Layer Protocol Phase: This phase is where each desired protocols' Network Control Protocols are invoked. For example, IPCP is used in establishing IP service over the line. Data transport for all protocols which are successfully started with their network control protocols also occurs in this phase. Closing down of network protocols also occur in this phase.Link Termination Phase: This phase closes down this connection. This can happen if there is an authentication failure, if there are so many checksum errors that the two parties decide to tear down the link automatically, if the link suddenly fails, or if the user decides to hang up his connection.
- #13: Weak-point: passwork and user are sent in clear text.