QuickSilver Controls QCI-DS026 QCI-S2-IG

Datasheet:QCI-DS026 QuickSilver Controls, Inc.
Date: 26 August 2014 www.QuickSilverControls.com
Property of QuickSilver Controls, Inc. Page 1 of 14 This document is subject to change without notice.

QuickControl® and QCI® are Registered Trademarks of QuickSilver Controls, Inc.
SilverLode™, SilverNugget™, SilverDust™, SilverSterling™, PVIA™, QuickSilver Controls™, and AntiHunt™ are
trademarks of QuickSilver Controls, Inc..
SilverSterling S2-IG
The SilverSterling™ is an OEM servo
controller/driver for QuickSilver's line of NEMA 11,
17, 23, and 24 frame, high torque, direct drive hybrid
servomotors, but is also capable of driving third
party DC brush and voice coil motors, 3 phase
brushless motors, open loop step motors, and the
new Mosolver™ hybrid servo with internal resolver
functionality*. The SilverSterling controller/driver is
available open framed (QCI-S2-IG-01) and
enclosed (QCI-S2-IG), and a Dual controller version
(QCI-S2-X2-IG).
They are designed to servo QCI’s I-Grade motors
through a single connector. This single cable
solution allows for easy installations and simple
cable routing.
* The Mosolver capability is present in units with a serial number of 2S1950 and higher. These
units have differential amplifiers added to interface with the Mosolver sense windings.
The SilverSterling features a 15 pin interface connector including 4 IO, CAN , RS-485, and
system power input. Four IO lines are brought out to the 15 pin connector. These may be
selected by means of jumpers on the 60 pin header if a secondary mezzanine PCB is not
utilized. If the expansion PCB is used, then these connector pins are free to be used by the
customer as assigned by the expansion PCB design.
QCI-S2-IG-01
QCI-S2-X2-IG
QCI-S2-IG
ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
sales@electromate.com
Sold & Serviced By:

QuickSilver Controls, Inc. Page 2 of 14
The SilverSterling also features a 60 pin header to allow simple and direct connection to
expansion boards for both future QuickSilver product extensions and OEM custom interface
printed circuit boards, eliminating the need for an additional cable and housing.
The 60 pin expansion header includes the ability to bring power to the board as well as access
to internal +12v, +5v, and +3.3v power supplies. Access is also provided to two SPI ports (one
of which may alternately be used as 4 simple IO), the internal CAN port, 4 configurable
analog/digital IO (12 bit A/D), one I2C port (which may be alternately used as 2 IO), A
secondary serial port (or alternately 3 I/O), motor encoder signals, one Capture Input (which
can also serve as general purpose IO) and an additional 11 general purpose IO. Four
connections to the 15 pin control connector are also brought out to the interface connector.
Drive capability of each controller is two or three phase at 3.5A RMS / 5A peak. DC Drive
capability is 6A (using both output phases connected in parallel).
System Overview
Point-to-Point Moves
 Relative or Absolute
 Velocity or Time Based
 S-Curve
Advanced Motion Profile Moves
 Profile Move Commands
 Register Based
o Position/Accel/Decel/Vel
o Modify On-the-Fly
Multi-Axis Linear Interpolation
 XYZ Coords Contained in Text File
 CANopen® used for local bus
 1000+ Points Stored In NV Memory
Built-In Voltage Clamp
 Regenerative Braking Resistor
Program and Data Storage
 32K Non-Volatile Memory:
 2000-3000 Program Lines
 User Data Examples
o CAM Tables
o Motion Profiles
o Lookup Tables
Electronic Slip Clutch/Brake
 Variable Torque
 Wind/Unwind Applications
Anti-Hunt™
 Optionally use Open Loop While
Holding
 No Servo Dither While At Rest
Communications
 RS-485 @ up to 230K Baud
 ASCII,Binary,Modbus®,DMX512
 Host Control While Servo in Motion
 CANopen® (Rev 03 SW and higher)
Programming Language
 Easy, Menu Driven Interface
 Command Parameter Prompts
 No Syntax Errors
 User Namable I/O and Registers
Advance PVIA™ Servo Loop
 100:1 Inertial Mismatch
 Direct Drive Oversized Inertial Loads
o Flywheels/Belt Drives
o Typically Without Gearheads
 More Stable Than PID
Digital 4 Quadrant Vector Drive
 DSP Driven for Reduced Noise
Multi-Task/Multi-Thread
Compatible with QCI Motor/Encoders
 NEMA 11 Frame
o 4000 Counts/Rev Encoder
o Up To 9 oz-in (continuous)
 NEMA 17 Frame
o IP50 or IP65
 NEMA 23 Frame
ELECTROMATE
www.electromate.com
Sold & Serviced By:

Electrical Specifications
Configurations
The QCI-S2-IG and QCI-S2-IG-01 are single controller units. The QCI-S2-X2-IG contains two
independent controllers in a single extruded heatsink; internally there are not connections
between the two controllers, and the option of a mezzanine board is not available.
Input Power
Voltage
+12 VDC to +48 VDC, regulated. Device must be initialized for the actual operating voltage.
Reverse Polarity Protection
Reverse polarity protection is available on the SilverSterling. (Note, however, if power supply is
not floating, connecting the V+ input to Ground will cause this potential to be present at the
common connection to communications and I/O lines, which may damage these lines or that to
which they are connected.
Input Current
4.5 Amps maximum for any input voltage, +12 VDC to +48 VDC per controller.
Output Power
Output/Driver Current
5 Amp peak, 3.5A RMS x 2 phases ; 6 A maximum for DC motors (using both phases in
parallel) per controller (restricted to 4.5 A input current - such as driving a lower voltage motor
from a higher voltage supply).
* With Adequate Heatsink. (4.0A RMS x 2 phases typical 45C rise from 22C, ambient, 3.5A
RMS x 2 typical 36C rise from 22C , using QCI-S2-IG heatsink with mounting feet horizontal,
still air; Vertical orientation typically several degrees lower. Measurement on outside of
heatsink, adjacent to driver.)
Maximum Output Power
200 Watts continuous power with adequate heat dissipation, 48V operation.
Encoder Interface
Designed to work with QCI’s I-Grade motor/encoders. Quadrature differential signals are
employed. Quadrature decoding used (i.e 2000 lines are decoded as 8000 counts.)
Standard interface is 485 differential inputs. These same differential inputs are also used to
interface to the Mosolver sense lines using the Encoder A, A-, B, B- inputs.
ELECTROMATE
www.electromate.com
Sold & Serviced By:

Inputs & Outputs
Digital Inputs
0 to +3.3 VDC. LVTTL level compatible.
On externally connected IO: Effective internal ~200K ohm pull-up impedance to +3.3 V. Inputs
have a series 220 ohm / 3.3v protector to ground / Series 220 ohm ESD protection network.
Do not exceed 5v on the inputs to prevent damage to the controller.
Internal IO present at header do not have additional protection; user must provide protection
needed on expansion PCB.
Digital Output Voltage
0 / +3.3 VDC.
Digital Output Current
Sinking or Sourcing
2mA; (externally connected IO include a 440 series impedance).
Analog Inputs
0 to +3.3 VDC input signal range.
12 bit ADC resolution (single).
Analog signals are read every servo cycle (120 μsec.) and the converted analog data is
processed through a 5 ms filter to reduce noise & transients.
Analog channels #1 and #2 are mapped to I/Os #4 and #3, respectively.
Mezzanine Connector
A 60 pin mezzanine connector has been provided to allow for easy interface to a user specific
printed circuit board. Note that the signals on this connector are not protected, and the user
must add protection to their circuit board for signals used. If the mezzanine board is not used,
pins 20C-20B, 19C-19B, 18C-18B, 17C-17B must be jumpered to access IO1-IO4 at the DB-
15HD SIP connector. (These signals must be connected on the mezzanine board if these
functions are wanted at the four IO pins, otherwise other functions can be routed to the four
external connections. Note that the Mezzanine connector may be unstuffed on S2-IG units not
having a Mezzanine board.
Clamp Resistor
The QCI-S2 comes with a built in regenerative voltage clamping circuit to prevent damage to
the driver from regenerated power associated with stopping a load. The QCI-S2-IG-01 has this
clamping resistor attached. The user is responsible for affixing this clamping resistor to a
suitable heatsink when installing the PCB.
ELECTROMATE
www.electromate.com
Sold & Serviced By:

Communications
Serial Interface
RS-485 multi-drop, Reduced unit load accommodates up to 255 nodes.
Protected up to +/- 70v not operating, +/-30V operating.
Note: RS-485 requires a nominal 120 ohm ½ W termination resistor at each end of the
network. This termination is not provided onboard and must be provided by the user. Note:
Short runs may work adequately with a higher impedace termination. The S2-IG does not
require a biased termination, but other attached devices may require a bias for proper
operation.
Protocols
8-bit ASCII, 9-bit binary, Modbus, and DMX512
Hardware Configuration Settings
Available Baud Rates: 2400, 4800, 9600, 19.2k, 28.8k, 57.6k, 115.2k or 230.4k
(250k only for DMX512)
Data Bits: 8 (9 bits for binary)
Stop Bits: 1.5 or 2
Parity Bit: None (Modbus supports None, Even, Odd)
CAN interface
The CAN bus connection is NOT isolated, but does include transceivers which have an
extended +/- 80v fault protection range. The CANopen® communications protocol allows the
unit to function as a master, slave, or peer on a CANopen network. See the SilverLode
CANopen User Manual for details on the CANopen protocol. This protocol operates
simultaneously and independently from the standard serial protocols.
Note that a 120 ohm ½ W termination resistor is required at each end of the CAN network
(only two per system). This termination is not provided onboard the controller and must be
provided by the user. For the CAN bus, this termination is not optional.
CANopen® and CiA® are registered community trade marks of CAN in Automation e.V.
STATUS LIGHTS
Three status lights are provided on each end of the box. Two sets of status lights are provided
to make it easier to see them with the box mounted in different orientations. The Blue Power
light indicates power is connected to the unit. The Red COMM LED indicates the unit is ready
(no program running) by a dim level, it is off between communications if a program is running.
It blinks brightly during each incoming communications frame. The Green Status light varies in
intensity with the motor torque (negative torque dimmer, positive torque brighter); if Done Bit is
configured the LED lights to indicate Done (See Set Done Bit command), is also used to blink
error codes if a fault is detected (and the Done bit is not configured).
ELECTROMATE
www.electromate.com
Sold & Serviced By:

Environmental Specifications
Operational Temperature
-10 C to +75 C
Storage Temperature
- 40 C to +85 C
Humidity
Continuous specification is 95% RH non-condensing.
Shock
Limitation is approximately 50g/11ms.
Specifications subject to change without notice. See www.QuickSilverControls.com for current
information.
Mounting the QCI-S2-IG-01
The Controller Driver is designed to be mounted between guides that support the edges of the
PCB not having LEDs or connectors. The guides should not overlap more than .025 over the
edge of the PCB. The driver IC is the tallest device on the back side of the board and defines
the distance between the PCB and the heat sink. Two 4-40 nuts are positioned equally about
and on the center line of the driver to allow access from the outside of the heatsink to pull the
PCB tight to the heatsink. If the third mounting nut (adjacent to the mezzanine connector), an
appropriate non-conductive spacer should be used to minimize twisting/flexing of the PCB. The
connector plane of the motor and SIP connectors is the reference for alignment and the
stabilizer for the connector end of the PCB.
Proper ESD handling techniques including grounding straps should be used while handling the
open frame printed circuit board to prevent damage. The D-sub shells are grounded and
should be the first contact to the PCB as an added measure.
THE THERMAL PAD ON THE DRIVER IS INTERNALLY CONNECTED TO THE DRIVER
SUBSTRATE AND NEEDS TO BE ATTACHED TO A GROUNDED HEATSINK. Connecting
the mounting bracket for the D-sub connectors to the heatsink will provide the needed
grounding path.
ELECTROMATE
www.electromate.com
Sold & Serviced By:

Mechnical Dimensions
QCI-S2-IG
QCI-S2-IG-01
ELECTROMATE
www.electromate.com
Sold & Serviced By:

QCI-S2-X2-IG
ELECTROMATE
www.electromate.com
Sold & Serviced By:

Connector Data
SilverSterling Interface Port (SIP)
This port provides Power, RS-485 serial
communications, CAN communications,
and four IO. It is not backwards
compatible with the SilverDust or
SilverNugget. The IO is nominally 0-3.3v
and should be limited to no more than 5v
to avoid damage. The CAN and RS485
have extended input voltage range to
improve robustness. Power ground and
logic ground are internally connected.
Motor Interface
QuickSilver Controls recommends our
QCI-C-D15P-D15S-nn (nn=length in
feet) cable to interface between the
motor and controller.
Mezzanine Header
The Mezzanine
Header provides
access to additional
signals when adding
a customer feature
board to the S2-IG
(Contact factory for
custom boards added to box), or S2-IG-01.
Four jumpers come standard on the S2-IG to connect the external IO (after input protection
network) to the internal IO on the processor. Note that the signals on this connector are not
protected and the user must add protection as needed to their customization board in order
to use these signals.
7
9
14
15
10
13
12
8
5
4
3
2
11
6
1
12 RS-485B
I/O #1
CAN_L
I/O #4
15
13
14
+5V OUTPUT 100mA
POWER GROUND
V+ (12-48 VDC)
RS-485A
POWER GROUND
LOGIC GROUND
V+ (12-48 VDC)
6
I/O #2
LOGIC GND (CAN GND)
9
10
11
7
8
CAN_H
I/O #3
2
4
5
3
1
14 4
12
11
6
7
13
8
9
2
1
3
15
10
5
6 Motor A +
Chassis Ground
Encoder Ground
Motor Memory Access
13 Encoder B+
14
15
Motor B -
Encoder Z +
Motor A -
Encoder Z -
Encoder A +
10
11
12
8
9
7
Chassis Ground
+ 5V Encoder Power
Motor B+
Encoder A -
Encoder B -
3
5
4
1
2
1 10 20
C
B
A
C
B
A
Jumpers to enable IO if no mezzanine board
ELECTROMATE
www.electromate.com
Sold & Serviced By:

Mezzanine Connector Pinout. Contact factory to use additional IO
A B C
1 +VP VPsen RxD_A - Primary serial port
2 +VDr = Internal
driver voltage
+VDr = Internal
driver voltage
TxD_A - Primary serial port
3 Power Ground (0v) Power Ground (0v) DE_A - Primary serial port
4 +12v @ 10mA +5v @ 100mA RxD_A ENA* (low to disable
internal 485)
5 SPIA Slave In
Master Out
TRST -
RESERVED
SPIB Slave In Master Out or
IO
6 SPIA Slave Out
Master In
TDI - RED* SPIB Slave Out Master In or
IO
7 SPIA Clock TDO - GREEN* SPIB Clock or IO
8 SPIA Chip Select* TMS - Output only SPIB Chip Select* or IO
9 CSO A - Additional
Chip select
+3.3v @ 100mA RxD_B - Seconadary serial
port or IO
10 CAN TX (internal
signal)
TCLK - Reserved TxD_B - Secondary serial
port or IO
11 CAN RX (Internal
signal)
SDAA - I2C or IO DE_B - Secondary serial port
or IO
12 Digital Ground SCLA - I2C or IO ENC_A - buffered from motor
encoder
13 ADCINA2 - Digital IO
or Analog
Digital Ground ENC_B - buffered from motor
encoder
14 ADCINB2 - Digital IO
or Analog
GPIO1 ENC_Z - buffered from motor
encoder
15 ADCINA4 - Digital IO
or Analog
GPIO3 ENC_S - high speed capture
of encoder or IO
16 ADCINB4 - Digital IO
or Analog
GPIO14 CAP_1 - High speed capture
or IO
17 No Connect Internal IO4 To SIP pin 14 via protection
network, ADC1 via protection
18 No Connect Internal IO1 To SIP pin 13 via protection
network
19 3.3v REF Internal IO3 To SIP pin 4 via protection
network
20 DRIVE ENABLE (pull
low to disable)
Internal IO2 To SIP pin 9 via protection
network
Jumpered by default
ELECTROMATE
www.electromate.com
Sold & Serviced By:

NOTE: GPIOXX pins refer to the processor pin naming convention. IOx pins follow the I/O
numbering of the I/O commands within QuickControl.
Input Power via Mezzanine Connector
Two alternate configurations are available if providing power through the mezzanine
connector.
The first configuration, shown right, connects
the power supply input (12-48V) to Pin 1A
referencing power ground on Pins 3A and 3B.
Pin 1A connects directly to power pins 1 and 7
of the DB15HD SIP port. Note that the power is
then available at the DB15HD SIP connector,
so care needs to be taken to prevent anything
from touching the supply on the exposed power
pins. The connector pin’s current rating must in
consideration and must not be exceeded.
The internal diodes isolate the supply from the
regenerated power, allowing the clamp to operate.
The second configuration, shown
right, connects the power supply
input (12-48V) to +Vdr (Pins 2A &
2B) through a high power Schottky
diode. The high power Schottky
diode (60V/6A) keeps the internal
driver regenerated power from
causing the power supply to shut
down and enables the clamp circuit
to operate properly.
It is also necessary to connect a
lower power Schottky diode
(60V/100mA) from the input power
supply to the +VP_S (Pin 1B) to
enable proper clamp circuit
operation. (Clamp will always be ON if this diode is not present!)
Power is isolated from DB15HD SIP port, pins 1&7 with this configuration.
ELECTROMATE
www.electromate.com
Sold & Serviced By:

Recommended Components
SilverSterling S2-IG Start-Up Materials
For first time users, QCI recommends purchasing the following items to aid with use of the S2-
IG controller:
 4’ DB15HD Motor I/F Cable (QCI-C-D15P-D15S-04)
 Breakout Module for SilverSterling (QCI-BO-S1)
 USB to RS485 converter (QCI-USB-RS485)
 Desired Motor
Optionally:
 210W, +48V Power Supply (S-210-48)
 Power Cable (QCI-C-ACP-FLY-6)
Software is free and available from our website.
See technical document QCI-TD072 on our website for details.
The Standard System detailed below shows a typical installation.
SilverSterling S2-IG System
ELECTROMATE
www.electromate.com
Sold & Serviced By:

Accessories:
1. Controller/Driver
SilverSterling S2-IG (QCI-S2-IG) is our standard closed frame controller/driver designed to
servo QCI’s I-Grade motors through a single connector.
2. Basic Breakout (QCI-BO-S1)
QCI recommends purchasing a breakout to simplify wiring power, RS-485 communication,
CAN and 4 I/O. The breakouts connect directly to the SilverSterling’s 15-pin interface port
(SIP).
3. Motor I/F Cable
For standard system, this D-sub type cable goes between the motor and the controller. The
generic part number is QCI-C-D15P-D15S-nn. Replace the last two digits “nn” with length of
cable in feet (i.e. –10 for 10 feet). Standard lengths are 1, 2, 4, and 10 feet.
For IP65 system, a special IP65 cable goes in between the motor and the controller. The
motors and cables are IP65, but not the controller/driver. The generic part number is
QCI-C-D15P-T14S-nn. Replace the last two digits “nn” with length of cable in feet
(i.e. –10 for 10 feet).
4. Motor
The SilverSterling S2 is capable of driving any NEMA 11, 17, 23 and 24 I-Grade
motor/encoder. See the following datasheets for more information:
QCI-DS007: NEMA 17 I-Grade Motor/Encoder
QCI-DS017: NEMA 11 M-Grade Motor/Encoder
QCI-DS029: NEMA 23 Mosolver™
QCI-AN066: BEI voice coil motors with the SilverSterling
5. Power Supply
Power supply selection is motor dependent, but the following will work with all the 17 and 23
frame motors.
SP-240-48 (48V, 5A, 240 Watt)
ELECTROMATE
www.electromate.com
Sold & Serviced By:

Part Numbers
SilverSterling™ IG Controller/Drivers
Driver Controller Options
QCI-S2-IG: 4 A RMS Per Phase
 Best paired with I-Grade
Motor/Encoders
 3.5A RMS per phase
 5A peak per phase
 4.5A @ 12v-48v
 Included Clamp circuit and
resistor.
IG – SilverSterling S2 IG
 4 TTL Inputs or Outputs
 1 Analog input
 1 PWM output
 ASCII, 9 bit Binary, Modbus®,
DMX-512®
 CANopen® (with Rev 03 sw)
 DB15HD (pin): SIP Connector
 DB15HD (socket): Motor I/F
X2-IG
 Two IG controllers in Enclosure
Blank – in Heat Sink Enclosure
01 – Board Only
 Requires user to properly
heat sink.
V1 – Board Only
 Motor Port with Vertical
DB15HD connector
 SMI Port with Right Angle
DB15HD connector
V2 – Board Only
 Motor Port with Right Angle
DB15HD connector
 SMI Port with Vertical
DB15HD connector
Example: For IG board only
QCI-S2 IG 01
Selection creates part number: QCI-S2-IG-01
Example Part Numbers:
QCI-S2-IG
QCI-S2-IG-01
QCI-S2-IG-V1
QCI-S2-IG-V2
QCI-S2-X2-IG
Contact Information
QuickSilver Controls, Inc.
712 Arrow Grand Circle
Covina, CA 91722
(626) 384-4760 or (888) 660-3801
(626) 384-4761 FAX
www.QuickSilverControls.com
ELECTROMATE
www.electromate.com
Sold & Serviced By:

QuickSilver Controls QCI-DS026 QCI-S2-IG

More Related Content

What's hot (20)

Similar to QuickSilver Controls QCI-DS026 QCI-S2-IG (20)

More from Electromate (20)

Recently uploaded (20)

QuickSilver Controls QCI-DS026 QCI-S2-IG