Six stroke engine using gasoline and r 123

IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 12 | Dec-2014, Available @ http://www.ijret.org 263
SIX STROKE ENGINE USING GASOLINE AND R-123
Sughosh Belur Sukesh1
1
Mechanical Engineering, Amrita School of Engineering, Karnataka, India
Abstract
In any Internal Combustion Engine, only 35% of the available energy is converted into the crankshaft energy. The remaining
portion of the energy is either expelled into the atmosphere or it increases the temperature of the engine block. This is desirable
as the conversion of heat energy into mechanical energy is more efficient at higher temperatures. However, beyond a certain limit
it sets up thermal stresses and in extreme cases it causes engine seizing. Thus a cooling system is employed to remove this heat
and transfer it into the atmosphere with the help of a radiator or a heat exchanger. In a six stroke engine, this heat transferred by
the coolant is reduced. As there have been several advancements in the recovery of energy from exhaust gases such as
turbochargers, Thermoelectric Generators and other such techniques, energy recovery by adding two strokes with a working fluid
as a refrigerant is unique. The study shows that around 30% of the heat is carried away by the coolant and hence this is amount
of energy that can theoretically be harvested. Since this offers a superior cooling system, the chances of detonation is also
considerably lowered. By reducing the amount of heat expelled into the atmosphere, the overall efficiency is improved. In today’s
age of rapidly depleting natural resources (fossil fuels), it is of utmost importance to converse these non-renewable sources of
energy. Since the IC Engine has reached a state of saturation, waste heat recovery is the best way to improve the efficiency and
hence reduce the fuel consumption.
Keywords: Six Stroke Engine, Waste heat Recovery, Cooling System, and Efficiency
--------------------------------------------------------------------***------------------------------------------------------------------
1. INTRODUCTION
In today’s world, IC Engines are a major source of power is
almost all automobiles and in a few energy production
sources. Since they run on fossil fuels which are non-
renewable source of energy, it is utmost importance to
converse it to the extent possible. As the emissions of the IC
Engines include CO2, CO, NOx and other harmful gases, by
improving the efficiency of the IC Engine, the emissions are
also reduced thus reducing its impact on the atmosphere.
This is of great relevance today since many problems
plaguing the earth’s atmosphere such as ozone layer
depletion, heat retention by greenhouse gases are caused by
the combustion of fossil fuels. In any IC Engine around 35%
of the heat produced by combustion is converted into useful
crankshaft power. While friction accounts for around 5% of
the power, exhaust gases and cooling systems account for
30% of the energy each. In today’s world, IC Engines have
reached a state of saturation i.e. further improvement can
only be marginal. In order to obtain significant
improvement, regeneration [1] is the only viable option.
There are several avenues to harvest the energy from the
exhaust gases such as turbochargers [2], thermoelectric
generators [3], Piezoelectric Generators [4]; recovering
energy from the cooling system is an esoteric one. Such an
energy recovery system would not only improve the
efficiency of an IC Engine but also reduce the amount of
fuel consumed. This paper gives a thorough insight into the
harvesting waste heat from the cooling system of an IC
Engine. The figure below shows the distribution of energy
of a typical IC Engine.
Fig 1- Pie Chart depicting distribution of energy in an IC
Engine
2. SIX STROKE ENGINE
In a conventional Gasoline powered IC Engine, there are
four strokes which are suction, compression, power and
exhaust. During suction, fresh air fuel mixture (called
charge) is sucked into the combustion chamber through the
inlet valve by the downward movement of the piston. The
exhaust valve is shut during this stroke. This charge is then
compressed by the upward motion of the piston in the
second stroke. The spark plug ignited this compressed
charge thus initiating the combustion of the fuel. Since both
the valves remain closed, it pushes the piston downwards
during the power stroke. During the exhaust stroke, the
upward movement of the piston coupled with the open
exhaust valve pushes the exhaust gases out of the cylinder.
The opening and closing of the valves is decided by cams. In
a six stroke engine [5], after the four strokes, a secondary
Cranksha
ft
Power, 3
5
Cooling
System, 3
0
Exhasut
Gases, 30
Friction,
5
Heat Balance Chart
Crankshaft
Power
Cooling
System
Exhasut
Gases
Friction

_______________________________________________________________________________________
working fluid (not the fuel) is injected into the cylinder
block through the inlet valve and both the valves are shut.
Since the secondary working fluid is at lower temperature,
on contact with the hot cylinder block, it expands thus
pushing the piston downwards. The upward movement of
the piston pushes the secondary working fluid out of the
cylinder into a storage tank generally or if the secondary
working fluid is air, it is expelled into the atmosphere
through the exhaust valve. This produces power and reduces
the load on the cooling system.
3. SECONDARY WORKING FLUID
There have been several six stroke engines which use water
or air as the secondary working fluid. The secondary
working fluid is injected into the cylinder through the intake
manifold at the end of the fourth stroke. The fluid absorbs
the heat in the cylinder block thus expanding and pushing
the piston downwards. This produces work and also absorbs
the heat from the cylinder thus reducing the load on the
coolant.
3.1 Water as the Secondary Working Fluid
Theoretically, water is injected into the cylinder at the end
of the fourth stroke [6]. Due to the temperature of the
cylinder block, it is converted into steam thus pushing the
piston downwards. Water was considered as a suitable
choice since it is abundantly available, easy to store and cost
effective.
One of the major problems encountered was that there were
instances where the water injected was not entirely
converted into steam. This resulted in traces of water left
behind in the cylinder. Since water inhibits combustion, it
affected the characteristics of the flame front in the
succeeding cycle. Also, cylinder showed signs of corrosion
due to the injection of water to the metal at high
temperature.
3.2 Air as the Secondary Working Fluid
Quite recently, air was considered as an alternative to water.
Air from the atmosphere is injected into the cylinder block
after the fourth stroke. Due to the thermal expansion, air
expands thus producing crankshaft work [7]. One significant
advantage was that the air could be expelled into the
atmosphere. The lack of a heat exchanger made the entire
set up lighter and more compact. Although this eliminated
most of the drawbacks, since there was no change of phase,
the expansion was lower. This resulted in a lower power
output from the additional two strokes.
3.3 R-123 as the Secondary Working Fluid
To overcome this, a suitable secondary fluid is to be
employed. By using R-123 as the secondary working fluid,
most of these problems can be overcome. R-123 is subjected
to Gas refrigeration cycle also known as Reverse Rankine
Cycle. Ideally, it consists of two isentropic and two isobaric
processes. The table below shows the various properties of
R-123
Table 1- Properties of R-123
Sl. No Parameter Value
1 Chemical Formula CHCl2CF3
2 Molecular weight 152.93
3 Boiling Point (1 atm) 27.85°C
4 Critical Temperature 183.68°C
5 Critical Pressure 36680 kPa
6 Critical Density 550 kgm-3
7 Critical Volume 0.00182 m3
kg-1
Consider the Figure below. It is a Gas Refrigeration Cycle
or also known as a Reverse Rankine Cycle [8]. The R-123
from the engine is passed through a compressor during
process 1-2. The high-pressure, high-temperature gas at state
2 is cooled by rejecting heat to the surroundings. This is
followed by an expansion process (2-3) in the turbine which
is ideally isentropic in nature. Finally, the fluid at state 3 is
injected into the engine after the fourth stroke.
Fig 2- The T-s graph of an ideal Reverse Rankine Cycle
4. MODIFICATIONS TO REVERSE RANKINE
CYCLE
In reality, there is always a pressure loss during heat
rejection and there are isentropic processes. Therefore to
ensure maximum turbine output, the fluid is passed through
the turbine after exiting the engine. This ensures that fluid is
not in liquid state at the turbine blades. To further aid
cooling of the fluid, the fluid is passed thorough a nozzle
and then expanded into a low pressure chamber. This
utilizes Joule-Thompson Effect which states that “when a
gas is expanded through well insulated device, at a
temperature below the maximum inversion temperature, the
enthalpy of the gas reduces”.
The heat exchanger is used to reduce the load on the
compressor. Since a part of the heat is already transferred
into the atmosphere, the enthalpy of the gas reduces. The
figure below shows the layout of the modified Reverse
Rankine Cycle. In the figure given below, the heat
exchanger 1 is the process of heat transfer from the engine
to R-123 and heat exchanger 2 is the process of heat transfer
from R-123 to the atmosphere

_______________________________________________________________________________________
Fig 3- The layout of the Modified Reverse Rankine Cycle
5. THERMAL ANALYSIS
The above concept was mathematically modelled and
solved. Below are the vital stages during the calculation of
the heat transferred.
Bernoulli’s Equation
𝑃
𝜌𝑔
+
𝑉
2𝑔
+ 𝑧 = 𝐶𝑜𝑛𝑠𝑡𝑎𝑛𝑡
R-123 is stored as saturated liquid in a storage tank at 2 bar
and 50°C. During the flow from the tank to the cylinder, the
friction between the fluid and the piping system is neglected.
Assuming the cylinder block is a standard temperature and
pressure, the potential head is negligible,
200 ∗ 10^3
13 ∗ 9.8
=
1 ∗ 10^3
9.62 ∗ 9.8
+
𝑉^2
2𝑔
V=174.81ms-1
To find out the nature of the fluid at a time infinitesimally
after entering the cylinder,
Re=
ρvD
𝜇
Re=
9.62∗174.81∗.0774
.4∗10^−3
Re= 3.11*10^5
Hence the flow is turbulent in nature.
For a turbulent flow,
Nu= .036*(Re^0.8)*(Pr^0.33)*(D/L)^.055
Pr0.033
= (
C∗μ
𝑘
) ^0.33
Pr0.033
= (
1022∗.4∗10−3
.075862
)^0.33
Pr0.033
= 1.752
(D/L) 0.055
= (0.074/0.077)0.055
(D/L) 0.055
= 0.098
Nu= 1.619*10^3
Nu=
h∗D
𝑘
1.619*10^3=
h∗0.074
0.07856
h= 1718W/m2
K
Q= h*A*(T surface – T ∞)
A= 2*π*0.077*0.074
A= 3.5*10-2
Q= 1718*3.5*10-2
* (200-150)
Q= 9.22*103
J
Therefore, the fluid absorbs 9.22kJ of heat every cycle.
Since R-123 is chemically stable up to 250°C, it is safe to
assume a factor of safety of 2 and hence the maximum
temperature attained by the fluid restricted to 125°C
Q= m*Cp* (T2 – T1)
Q= m*1022*(125 – 50)
m=.12kgrev-1
Work done per cycle= P*(V2 – V1)
Wc = 200*103
*(0.0767*.12 - 0.00025)
Wc = 1.79kJ/rev
This is the work extra work obtained by the expansion of the
secondary working fluid. Assuming a mean engine speed of
1500 rpm,
No. of revolutions= 1500/60= 25 rev/s
W=1.79*25= 44.75kW
To compress R-123 from standard temperature and pressure,
a compressor of
WcompT =
𝛾
𝛾−1
*m*R*(Tout – Tin)
WcompT= 3.5*0.12*55.4*(125-50)
WcompT= 17.45kW
Assuming an efficiency of 80%,
WcompA=WcompT/Efficiency
WcompA= 21.82kW

_______________________________________________________________________________________
Wnet= W- WcompA
Wnet= 44.75-21.82
Wnet= 23kW
6. CONCLUSION
Since IC Engines today have reached a state of saturation in
terms of efficiency, regeneration is the only viable option.
There is large potential for energy recovery through
regeneration in an IC Engine. Although there have been
several advances in the recovery of heat from exhaust gases,
regeneration through cooling system is in its nascent
systems. Six stroke engines have been conceptualized for
decades now. The amount of money to be spent to
regenerate a unit of power from cooling systems is a lot
higher than designing a larger engine. Hence, automobile
companies go for a larger engine. However, with today’s
energy crisis, it is of utmost importance to save every drop
of fossil fuel. Therefore, automobile companies should
invest in regenerative systems. Six stroke engines is a
wonderful concept that integrates concepts of Rankine Cycle
and Vapor Compression Cycle with Diesel Cycle to improve
efficiency.
REFERENCES
[1]. T. Endo, S. Kawajiri, Y. Kojima, K. Takahashi, T.
Baba, S. Ibaraki, T. Takahashi, “Study on Maximizing
Exergy in Automotive Engines,” SAE Int. Publication 2007-
01-0257, 2007.
[2]. Sundström, E., Semlitsch, B., and Mihaescu, M.,
"Assessment of the 3D Flow in a Centrifugal compressor
using Steady-State and Unsteady Flow Solvers," SAE
Technical Paper 2014-01-2856, 2014, doi:10.4271/2014-01-
2856.
[3]. Zhang X, Chau KT, “An automotive thermoelectric–
photovoltaic hybrid energy system using maximum power
point tracking,” Energy Conversion and Management 2011;
52(1):641–7.
[4]. Raju, B., Bianchini, E., Arata, J., and Roylance, M.,
"Improved Performance of a Baffle-less Automotive
Muffler Using Piezoelectric Materials," SAE Technical
Paper 2005-01-2353, 2005, doi:10.4271/2005-01-2353.
[5]. Williams, D., Koci, C., and Fiveland, S., "Compression
Ignition 6-Stroke Cycle Investigations," SAE Int. J.
Engines 7(2):656-672, 2014, doi:10.4271/2014-01-1246.
[6]. James C. Conklin, James P. Szybist, A highly efficient
six-stroke internal combustion engine cycle with water
injection for in-cylinder Exhaust heat recovery. Energy, The
International Journal, Volume 35, Issue 4, pp. 1658-1664
(2010).
[7]. Hayasaki, T., Okamoto, Y., Amagai, K., and Arai, M.,
"A Six-Stroke DI Diesel Engine Under Dual Fuel
Operation," SAE Technical Paper 1999-01-1500, 1999,
doi:10.4271/1999-01-1500.
LIST OF SYMBOLS USED
 P- Pressure
 P1- Pressure in storage Tank
 P2- Pressure in Cylinder
 ρ- Density
 g- Acceleration due to gravity
 v2- Velocity in the cylinder
 Re- Reynold’s Number
 µ- Viscosity
 D- Diameter of Cylinder (Bore)
 L- Stroke of Cylinder
 Pr- Prandtl Number
 C- Specific heat of R-123
 k- Conductivity of R-123
 h- convective heat transfer coefficient
 A- Area of interaction b/w R-123 and cylinder
 Tsurface- Temperature of Cylinder
 T∞- Temperature of R-123 at entry of cylinder
 Q- Heat transferred from the cylinder
 m- Mass flow rate of R-123
 Wc- Work done per cycle
 WcompT- Theoretical Work by the compressor
 WcompA- Actual Work by the compressor
 Wnet- Net work done
BIOGRAPHIE:
Sughosh Belur Sukesh, Pursuing Bachelor
of Technology (specialization Mechanical
Engineering) at Amrita School of
Engineering, Bangalore. Currently in 8th
Semester
Contact Info
Email- sughosh9055@gmail.com
Phone - +917760402518

Six stroke engine using gasoline and r 123

More Related Content

What's hot (20)

Viewers also liked (16)

Similar to Six stroke engine using gasoline and r 123 (20)

More from eSAT Journals (20)

Recently uploaded (20)

Six stroke engine using gasoline and r 123