Ssr 303 user manual
0 likes965 views
This document provides instructions for installing and operating a single channel Z-Wave receiver called the SSR 303. The SSR 303 can be controlled by third party Z-Wave controllers and will act as a repeater to extend the range of the Z-Wave network. It has buttons to manually switch the relay on or off and LEDs to indicate its status and network connection. The document describes how to include the SSR 303 in a Z-Wave network and supported Z-Wave command classes.
Ssr 303 user manual
- 1. 1 SSR 303 One Channel 3 Amp Switch (Rx Only) - Z-Wave User and Installation Instructions
- 2. 2
- 3. 3 The Secure SSR 303 receiver is a single channel receiver originally designed for the control of central heating which can also be operated by third party controllers which support ‘Thermostat Mode SET’ commands or‘BinarySwitchSET’commands. This SSR 303 will act as a repeater once added into the Z-Wave network, providing an alternative communication route for units which otherwise would not be within communication distance of each other. The Secure SSR 303 forms part of a Z-Wave PlusTM homeautomation network. This document provides information specific to the Z- Wave technology implemented, to ensure interoperability between the SSR 303 receiver and other Z-Wave products.
- 4. 4 SSR 303 Receiver Unit The SSR 303 receiver unit receives the Z-Wave radio signals from the 3rd party Z-Wave controllers. In the unlikely event of a communication failure it is possible to override the system and switch ON and OFF using the ON/OFF buttons on the SSR 303 receiver as a local override. If the override is used to override the system when it is functioning correctly then the override will be cancelled by the next switching operation and normal operation will be resumed. In any case, with no further intervention, normal operation will be restored within one hour of theoverride being operated.
- 5. 5 Installing the receiver Installing theSSR 303 The SSR 303 receiver should be located as near as is practical to the device to be controlled, as well as a convenient mains electricity supply. To remove the wall plate from the SSR 303, undo the two retaining screws located on the underside, the wall plate should now be easily removed. Once the wall plate has been removed from the packaging please ensure the SSR 303 is re-sealed to prevent damage from dust, debris etc. The wall plate should be fitted with the retaining screws located at the bottom and in a position which allowsa total clearance of at least 50mm around the SSR 303 receiver.
- 6. 6 DirectWallMounting Offer the plate to the wall in the position where the SSR 303 is to be mounted and mark the fixing positions through the slots in the wall plate. Drill and plug the wall, then secure the plate into position. The slots in the wall plate will compensate for any misalignment of the fixings. WallBoxMounting The wall plate may be fitted directly on to a single gang flush wiring box complying with BS4662, using two M3.5 screws. The receiver is suitable for mounting on a flat surface only; it is not suitable for mounting on an unearthed metal surface.
- 7. 7 Electrical Connections All necessary electrical connections should now be made. Flush wiring can enter from the rear through the aperture in the back plate. The mains supply terminals are intended to be connected tothesupply bymeans of fixed wiring. The receiver is mains powered and requires a 3 Amp fusedspur. The recommended cablesize is 1.Omm2. The receiver is double insulated and does not require an earth connection, an earth connection block is provided on the back plate for terminating any cable earth conductors. Earth continuity must be maintained and all bare earth conductors must be sleeved. Ensure that no conductors are left protruding outside the central spaceenclosed bythe back plate.
- 8. 8 Please ensure that all installations comply with current IEE regulations. SSR303 internal wiring diagram Internal Electronics 230V ~ 50Hz COMM OFF ON The receiver has voltage free contacts. Fit link between L & 2 for mains voltage applications
- 9. 9 Receiver status LED This unit has three buttons and three LEDs - ON, OFF and Network (from top to bottom) that are used as follows:- LED indication Unit mode Button usage Solid OFF LED Flashing Network LED Unit is currently removed from the network OFF and ON - Switches channel relay OFF or ON respectively. Network - Network function Flashing ON LED (Green) 3s only Solid OFF LED Unit has been successfully added on the network OFF and ON - No function Network - Network function Solid OFF LED Unit is reflecting the status OFF the relay unit. The output is OFF. Or, unit has finished the addition process. Or, unit has been added and has just been powered up on the mains OFF and ON - switches channel relay OFF or ON respectively. Network - Network function
- 10. 10 Solid ON LED Unit is reflecting the status of the relay output. The output is ON. OFF and ON - switches channel relay OFF or ON respectively. Network - Network function Solid OFF LED Solid Network LED Unit is in failsafe mode and the relay output is OFF. OFF and ON - switches channel relay OFF or ON respectively. Network - Network function Solid ON LED Solid Network LED Unit is in Failsafe mode and the relay output has been turned ON via the ON button Or, Unit is currently removed from the network and ON by button operation. OFF and ON - switches channel relay OFF or ON respectively. Network - Network function
- 11. 11 Adding to a third partycontroller To add the unit to a 3rd party controller follows these steps, alsoknown as ‘inclusion’inZ-Wave terminology. - Ensure the network LED is flashing on the SSR 303, if not follow the steps in ‘Disconnecting from a network’first. - Put the 3rd partycontrollerintoinclusionmode. - Press and hold the network button on the SSR 303 until the ‘ON’LED’s start flashing. - The SSR 303 has been added onto the network when the ‘OFF’LED goes solid red. NOTE: If the ON LED does not flash then the add process has been unsuccessful.
- 12. 12 Removing from a network To remove from a Z-Wave network, follow the steps, below, also known as ‘exclusion’ in, Z-Wave, terminology - Put the 3rd party controller intoexclusionmode. - Press andhold thenetwork buttonon the SSR 303. - The SSR 303 has been removed from the network when the Network LED starts flashing. NOTE: If the Network LED does not flash the remove process has been unsuccessful. NOTE: This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications.All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
- 13. 13 Node Information Frame - NIF Pressing and holding the network button for 1 second will trigger the SSR 303 to issue a Node Information Frame and enter Classic learn mode for 2s and then in NWI (Network Wide Inclusion) learn mode. This is useful to associate/disassociate the SSR 303 with a control group or just to determine the device and command classes supported. This can be done at any timebut will not provide anyindication tothe operator. Z-Wave Repeater This SSR 303 will act as a repeater once added into the Z-Wave network, providing an alternative communication route for units which otherwise would not bewithincommunication distance of each other. Device reset: “Please use this procedure only when the primary controller is missing or otherwise inoperable.” Follow “Removing from a Network” process.
- 14. 14 Supported Device and command classes Z-Wave Plus Device Classes Implemented Device Class Generic Device Class: Specific Device Class: Basic Device Class: GENERIC TYPE SWITCH BINARY SPECIFIC TYPE POWER SWITCH BINARY ROUTING SLAVE Command Class Commands Supported Manufacturer Specific (V2) Get Report Device Specific Get Device Specific Report Manufacturer ID = 0x0059 Product Type ID = 0x0003 Product ID = 0x0005 (SSR 303) Device ID Type 0 and 1 for serial number (Data format Binary, length4 Bytes) Version (V2) Get Report Version Command Class Get Version Command Class Report Provides the version number of the Z-Wave stack, Command Class, Firmware and Hardware.
- 15. 15 Z-Wave Plus Info (V2) Get Report RoleType:ROLE_TYPE_SLAVE_ALWAYS_ON Node Type: ZWAVEPLUS_INFO_REPORT_NODE_TYPE_ZWAVEPLUS_NODE Installer Icon: ICON_TYPE_GENERIC_ON_OFF_POWER_SWITCH User Icon: ICON_TYPE_GENERIC_ON_OFF_POWER_SWITCH Association (V2) Set Get Report Remove Supported Groupings Get Supported Groupings Report Specific Group Get Product supports one group (Lifeline) and has a maximum of 4 nodes. Association Group Info (V1) Group Name Get Group Name Report Group Info get Group Info Report Group Command List Get Group Command List Report
- 16. 16 Only one association group is supported Group 1: name - “Lifeline” Profile MSB -ASSOCIATION_GROUP_INFO_REPORT_PROFILE_GENERAL Profile LSB - ASSOCIATION_GROUP_INFO_REPORT_PROFILE_GENERAL_LIFELINE Supported Command class and command - COMMAND_CLASS_SWITCH_BINARY, SWITCH_BINARY_REPORT Thermostat Mode (V1) Set Get Report Supported Get Supported Report Only ‘Idle Mode’ and ‘Heat Mode’ are supported within this command class, which can either set or read. The SSR 303 has a failsafe mode where by the relay is turned OFF if another Thermostat Mode SET command has not been received within 60 minutes. Switch Binary (V1) Set Get Report Supports SET and GET to control the relay. Opposed to the Thermostat command class there is no failsafe mode. If Binary Switch SET command is received than previously active failsafe mode closed.
- 17. 17 Basic (V1) Set Get Report The Basic command class has been mapped to Switch Binary command class as follows: Basic Set : Mapped to Switch Binary Set. Basic Get : Mapped to Switch Binary Get. Basic Report : Mapped to Switch Binary Report Same as Switch Binary command class there is no failsafe mode. If Basic SET command is received than previously active failsafe mode closed. Power Level (V1) Power Level Set Power Level Get Power Level Report Power Level Test Node Set Power Level Test Node Get Power Level Test Node Report Power Level Command Class defines RF transmit power controlling commands useful when installing or testing a network. Note: For more information about Z-Wave command classes and their use refer to "SDS12652 and SDS12657 Z-Wave Command Class Specification" version 8 or above. Note: After removing from existing Z-Wave network, device comes in factory default state and will not send device reset locally notification.
- 18. 18 Receiver specification SSR 303 Power Supply 230v 50Hz Contact type Micro disconnection Wiring configuration Voltage free c/o (SPDT) Contact voltage rating 230v ac 50Hz (30v dc) Contact current rating 3A (1A inductive) Impulse rating Category II – 2500v Transmitter frequency 868.42MHz Receiver category Category 3Power Class Class B Standards EN 60730-2-7 ETSI EN 300 220-2 / ETSI EN 301 489-3 Dimensions 86 x 86 x 36.25mm Enclosure Flame retardant thermoplastic Ingress protection IP30 Pollution degree Degree 2 Insulation class Class II Software class A Control type Type 1B Electronic control Temperature r a n g e 0-40˚C Ball pressure temperature 75˚C Purpose of control 1 channel RF receiver switch
- 19. 19 European Head Office Secure Controls (UK) Ltd. South Bristol Business Park Roman Farm Road Bristol, BS4 1UP, UK e: info@securetogether.com www.securetogether.com European Sales Office CEWE Instrument AB Box 1006, 611 31 Nyköping t: +46 8 600 80 60 e: info@securetogether.com www.securetogether.com www.securetogether.com Australia Sales Office Secure Australasia Pty Ltd 258 Darebin Road Fairfield VIC 3078 Australia p: +61 3 9485 6000 f: +61 3 9485 6099 e: info@securetogether.com www.securetogether.com
- 20. Secure Meters Ltd Pratap Nagar Industrial Area Udaipur 313003 India p: +91 294 2492 300-05 f: +91 294 2492 310 e: mktg@securetogether.com www.securetogether.com Elegant Metering Solutions FZE 4EA 326, P.O. Box 54857 Dubai Airport Free Zone Dubai, UAE p: +971 50 6575166 f: +971 04 204 5619 e: emsfze@emsdxb.ae www.securetogether.com Part Number P84074 Issue Number 6