Steering system

STEERING GEARS

STEERING MECHANISMS

 Steering is the term applied to the collection of components, linkages, etc.
which will allow a vehicle to follow the desired course.

 An automobile is steered with the help of steering gears and linkages,
which transfer the motion of the hand operated steering wheel to the
pivoted front wheel hubs via steering column. The other parts that are used
for steering a vehicle are steering wheel pads, steering shafts, steering
boxes, steering arms and steering stabilizers. These parts are made of
durable materials like stainless steel, iron, aluminum, copper, magnesium,
titanium, platinum, rubber, and plastics.

 It helps in swinging the wheels to the left or right.

 It converts the rotary movement of the steering wheel into an angular turn
of the front wheels.

 It multiplies the effort of the driver by leverage in order to make it fairly
easy to turn the wheels.

 It absorbs a major part of the road shocks thereby preventing them to get
transmitted to the hands of the driver

 The term "steering geometry" (also known as "front-end
geometry") refers to the angular Relationship between suspension
and steering parts, front wheels, and the road surface. Because
alignment deals with angles and affects steering, the method of
describing alignment measurements is called steering geometry.

 There are five steering geometry angles : Camber , Caster ,Toe,
Steering axis inclination, and Toe-out on turns

 The steering gear is a device for converting the rotary motion of the steering wheel into
straight line motion of the linkage with a mechanical advantage.

 If the steering wheel is connected directly to the steering linkage it would require a great
effort to move the front wheels. Therefore, to assist the driver, a reduction system is used
having a steering ratio (the ratio between the turn of the steering wheel in degrees or
handlebars and the turn of the wheels in degrees ) between 10:1 to 24:1 the actual value
depending upon the type and weight of the vehicle.

 A higher steering ratio means that you have to turn the steering wheel more, to get the
wheels turning, but it will be easier to turn the steering wheel. A lower steering ratio
means that you have to turn the steering wheel less, to get the wheels turning, but it will
be harder to turn the steering wheel. Larger and heavier vehicles like trucks will often
have a higher steering ratio, which will make the steering wheel easier to turn. In normal
and lighter cars, the wheels becomes easier to turn, so the steering ratio doesn't have to
be as high. In race cars the ratio becomes really low, because you want the vehicle to
respond a lot quicker than in normal cars.

The steering gears are enclosed in a box, called the steering gear box.
There are many different designs of steering gear box.

They are as follows:

 Worm and wheel steering gear
 Worm and sector steering gear
 Cam and lever / peg steering gear
 Recirculating ball steering gear
 Rack and pinion steering gear.

 The system consists of worm wheel which is carried in bearings in a cast
iron case. The case is made in halves. The outer end of the worm wheel is
fixed to a drop arm which is having ball end to connect the side rod. The
side rod is connected to the steering arm which is fixed to the stub axles.
The worm which is keyed on to a steering shaft have a mesh with the
worm wheel. The steering wheel is mounted at the upper end of the
steering shaft. When driver rotates the steering wheel then drop arm
moves either backward or forward direction. This motion results in
motion of the stub axles.

 In this type of steering box, the end of the shaft from the steering wheel has a worm
gear attached to it. It meshes directly with a sector gear (so called because it's a
section of a full gear wheel). When the steering wheel is turned, the shaft turns the
worm gear, and the sector gear pivots around its axis as its teeth are moved along the
worm gear. The sector gear is mounted on the cross shaft which passes through the
steering box and out the bottom where it is splined, and the pitman arm is attached to
the splines. When the sector gear turns, it turns the cross shaft, which turns the pitman
arm, giving the output motion that is fed into the mechanical linkage on the track rod.
The box itself is sealed and filled with grease. In actual case, the worm wheel is not
essential as it is having only partial rotation. Hence in this type only a sector of wheel
is used instead of worm wheel.

 Here a helical groove is formed at the bottom end of the steering wheel
shaft. The helical groove engages the projected pin of the drop arm
spindle lever. The drop-arm is made rigid with the lever/peg by a splined
spindle.

 The to and fro motion is obtained at the drop-arm when the steering
wheel shaft is turned. This motion results the turning of the stub axles.
The end play of the steering wheel shaft can be adjusted by putting a
suitable washer at the lock nut. The meshing of the projected pin in
helical groove is also adjusted by a screw provided at the end of the lever
spindle. In the recent models, the projected pin is made in the form of a
roller. The projected pin may be one or two in number, accordingly they
are referred as cam and single lever or double lever steering gear
mechanism

 It consists of a worm at the end of steering rod. A nut is mounted
on the worm with two sets of balls is the grooves of the worm, in
between the nut and, the worm. The balls reduce the friction
during the movement of the nut on the worm. The nut has a
number of teeth on outside, which mesh with the teeth on a worm
wheel sector, on which is further mounted the drop arm.

 When the steering wheel is turned, the balls in the worm roll in
the grooves and cause the nut to travel along the length of the
worm. The balls, which are in 2 sets, are recirculated through the
guides. The movement of the nut causes the wheel sector to turn
at an angle and actuate the link rod through the drop arm,
resulting in the desired steering of the wheels. The end play of the
worm can be adjusted by means of the adjuster nut provided.

 To compensate for the wear of the teeth on the nut and the worm,
the two have to be brought nearer bodily. To achieve this, the
teeth on the nut are made tapered in the plane perpendicular to the
plane of Figure.

 Rack-and-pinion steering is quickly becoming the most common type of
steering on cars, small trucks and SUVs. On most cars, it takes three to
four complete revolutions of the steering wheel to make the wheels turn
from lock to lock (from far left to far right).

The rack-and-pinion gear set does two things:
 It converts the rotational motion of the steering wheel into the linear
motion needed to turn the wheels.
 It provides a gear reduction, making it easier to turn the wheels.

 A rack-and-pinion gear set is enclosed in a metal tube, with each end of
the rack protruding from the tube. A rod, called a tie rod, connects to
each end of the rack. The pinion gear is attached to the steering shaft.
When you turn the steering wheel, the gear spins, moving the rack. The
tie rod at each end of the rack connects to the steering arm on the spindle.

 Some cars have variable-ratio steering, which uses a rack-and-pinion gear set that
has a different tooth pitch (number of teeth per inch) in the center than it has on the
outside. This makes the car respond quickly when starting a turn (the rack is near
the center), and also reduces effort near the wheel's turning limits

 When the rack-and-pinion is in a power-steering system, the rack has a
slightly different design. Part of the rack contains a cylinder with a piston
in the middle. The piston is connected to the rack. There are two fluid
ports, one on either side of the piston. Supplying higher-pressure fluid to
one side of the piston forces the piston to move which in turn moves the
rack so providing power assist.

 Power steering has two types of device for steering effort one type is a
hydraulic device utilizing engine power. The other type utilizes an
electric motor. For the former, the engine is used to drive a pump. For the
latter, an independent electric motor in the front luggage compartment is
used the pump. Both develop fluid pressure, and this pressure acts on a
piston within the power cylinder so that the pinion assists the rack effort.
The amount of this assistance depends on the extent of pressure acting on
the piston. Therefore, if more steering force is required, the pressure must
be raised. The variation in the fluid pressure is accomplished by a control
valve which is linked to the steering main shaft.

 ELECTRIC POWER STEERING (EPS OR EPAS) is designed to use
an electric motor to reduce effort by providing steering assist to the driver
of a vehicle. Sensors detect the motion and torque of the steering column,
and a computer module applies assistive torque via an electric motor
coupled directly to either the steering gear or steering column. This
allows varying amounts of assistance to be applied depending on driving
conditions. The system allows engineers to tailor steering-gear response
to variable-rate and variable-damping suspension systems achieving an
ideal blend of ride, handling, and steering for each vehicle. In the event
of component failure, a mechanical linkage such as a rack and pinion
serves as a back-up in a manner similar to that of hydraulic systems.

 HYDRAULIC POWER STEERING (HPS) is a hydraulic system for reducing the
steering effort on vehicles by using hydraulic pressure to assist in turning the
wheels. It is intended to provide for easier driving direction control of the car while
preserving "feedback", stability and unambiguity of the trajectory specified. The
steering booster is arranged so that should the booster fail, the steering will continue
to work (although the wheel will feel heavier).

The steering booster consists of the following basic elements:
 Steer torque detector
 Controlled pressure distributor case
 Hydraulic booster pump
 Tank with a working liquid
 Connection hoses

The working liquid, also called "hydraulic fluid" or "oil", is the medium by which
pressure is transmitted. Common working liquids are based on mineral oil. For
pressure restriction in the pump there is a restrictive valve, which is adjusted on
different cars in a range from 7 to 13 MPa.

 Hydraulic Power Steering System is complicated compared with Electric Power
Steering

 Hydraulic Power Steering System usually weighs more than Electric Power Steering

 Hydraulic Power Steering uses hydraulic fluids for operation whereas there is no
such fluid needed for Electric Power Steering, thus Electric Power Steering needs
less maintenance compared to hydraulic power steering.

 Electric Power Steering gives better response at different speeds as compared to
Hydraulic Power Steering

 Eclectic Power Steering is less prone to problems and faults and are more durable as
compared to Hydraulic power steering.

 Hydraulic power steering extracts power from engine, so it reduces the fuel mileage
of the engine. Electric power steering consumes power from battery which is also
charged by engine, but it consumes less power compared to Hydraulic power
steering. So a car having Electric power steering will give more mileage than one
with Hydraulic power steering.

 Electro-hydraulic power steering systems, sometimes abbreviated EHPS, and also
sometimes called "hybrid" systems, use the same hydraulic assist technology as
standard systems, but the hydraulic pressure is provided by a pump driven by an
electric motor instead of being belt-driven by the engine.
 By providing power assist via hydraulic pressure, this system delivers a naturally
smooth steering feel and, thanks to the flexibility of control allowed by electric
power, offers more precise steering power characteristics. It also improves fuel
economy since the electric powered pump operates only when steering assist is
needed

Steering system

More Related Content

What's hot (20)

Similar to Steering system (20)

More from Gaurav Gunjan (12)

Recently uploaded (20)

Steering system