CCNP Switching Chapter 7

© 2007 – 2016, Cisco Systems, Inc. All rights reserved. Cisco Public
SWITCH v7.1 Chapter 7
1
Chapter 7:
Network Management
CCNP SWITCH: Implementing Cisco IP Switched Networks

Chapter 7
2© 2007 – 2016, Cisco Systems, Inc. All rights reserved. Cisco Public
Chapter 7 Objectives
This chapter covers the following topics related to network
management and mobility:
 AAA
 Identity-based networking 802.1X
 NTP
 SNMP

Chapter 7
AAA

Chapter 7
AAA
 ■ Authentication
• Authentication is the process of identifying a user before that user is
allowed access to a protected resource.
 ■ Authorization
• After the user gains access to the network, authorization is performed.
• Authorization allows you to control the level of access users have.
 ■ Accounting
• Accounting is performed after authentication. Accounting enables you
to collect information about the user activity and resource
consumption.

Chapter 7
AAA Benefits
 Increased flexibility and control of access configuration
• AAA offers additional authorization flexibility on a per-command or
per-interface level, which is unavailable with local credentials.
 Scalability
• As the network grows, managing a large number of users on multiple
devices becomes highly impractical and error-prone, with a lot of
administrative burden.
 Standardized authentication methods
• AAA supports the RADIUS protocol, which is an industry open
standard. This ensures interoperability and allows flexibility because
you can mix and match different vendors.
 Multiple backup systems
• You may specify multiple servers when configuring authentication
options on the method list, combining them in a server group.

Chapter 7
RADIUS and TACACS+ Overview
 RADIUS and TACACS+ are AAA protocols.
 Both use the client/server model.
 As shown in Step 1, a user or machine sends a request to a networking
device such as a router that acts as a network access server when
running AAA.
 The network access server then communicates (2, 3) with the server
exchanging RADIUS or TACACS+ messages.
 If authentication is successful, the user is granted (4) an access to a
protected resource (5), such as a device CLI, network, and so on.

Chapter 7
TACACS+ Versus RADIUS

Chapter 7
RADIUS Authentication Process

Chapter 7
TACACS+ Authentication Process

Chapter 7
Configuring AAA
 To enable AAA, the first step is to configure the aaa new-
model command in global configuration mode.
 This step essentially enables AAA capability.
 In addition, until this command is enabled, all other AAA
commands are hidden.
 The aaa new-model command immediately applies local authentication
to all lines and interfaces (except console line con 0).
 To avoid being locked out of the router, it is a best practice to define a
local username and password before starting the AAA configuration.

Chapter 7
Configuring RADIUS Access
 Switch(config)# radius server configuration-name
 Switch(config-radius-server)# address ipv4 hostname [auth-
port integer ] [ acct-port integer]
 Switch(config-radius-server)# key string
 Switch(config)# aaa group server radius group-name
 Switch(config-sg-radius)# server name configuration-name

Chapter 7
Apply RADIUS Method List to vty
 Switch(config)# aaa authentication login radius_list group
Mygroup2 local
 Switch(config)# line vty 0
 Switch(config-line)# login authentication radius_list

Chapter 7
Configuring TACACS+ for Console and vty
Access
 Switch(config)# tacacs server configuration-name
 Switch(config-server-tacacs)# address ipv4 hostname
 Switch(config-server-tacacs)# port integer
 Switch(config-server-tacacs)# key string
 Switch(config)# aaa group server tacacs+ group-name
 Switch(config-sg-tacacs+)# server name configuration-name

Chapter 7
AAA Authorization
To configure authorization, complete the following steps:
 Step 1. Define a named list of authorization methods.
 Step 2. Apply that list to one or more interfaces (except for the
default method list).
 Step 3. The first listed method is used. If it fails to respond, the
second one is used, and so on until all listed methods are
exhausted. Once the method list is exhausted, a failure message
is logged.
 Switch(config)# aaa authorization authorization-type list-
name method-list
 Switch(config)# line line-type line-number
 Switch(config)# authorization { arap | commands level |
exec | reverse-access } list-name

Chapter 7
AAA Accounting
AAA accounting has the same rules and configuration steps
as authentication and authorization:
 Step 1. You must first define a named list of accounting
methods.
 Step 2. Apply that list to one or more interfaces (except for
the default method list).
 Step 3. The first listed method is used; if it fails to respond,
the second one is used, and so on.
 Switch(config)# aaa accounting accounting-type list-
name { start-stop | stop-only | none } method-list
 Switch(config)# interface interface-type interface-
number
 Switch(config-if)# ppp accounting list-name

Chapter 7
Limitations of TACACS+ and RADIUS
RADIUS may not be the optimal choice in the following situations:
 Device-to-device situations
• RADIUS does not offer two-way authentication.
 Networks using multiple service
• RADIUS generally binds a user to a single service model.
TACACS+ may not be the optimal choice in the following situations:
 Multivendor environment
• TACACS+ is a Cisco proprietary protocol
 When speed of response from the AAA services is of
concern
• TACACS+ uses TCP as a transport protocol mechanism.

Chapter 7
Identity-Based
Networking

Chapter 7
Identity-Based Networking
 Identity-based networking is a concept that unites several
features to include authentication, access control, mobility,
and user policy components with the aim to provide and
restrict users with the network services that they are entitled
to.
 From a switch perspective, identity-based networking allows
you to verify users once they connect to a switch port..

Chapter 7
IEEE 802.1X Port-Based Authentication
Overview
 Until the client is authenticated, 802.1X access control
allows only EAPOL, Cisco Discovery Protocol (CDP), and
Spanning Tree Protocol (STP) traffic to pass through the
port to which the client is connected. After authentication is
successful, normal traffic can pass through the respective
port.

Chapter 7
802.1X Client/Server Model
 Client
• Usually a workstation or laptop with 802.1X-compliant client software.
• Most modern operating systems include native 802.1X support.
• The client is also referred to as a supplicant in 802.1X terminology.
 Authenticator
• Usually an edge switch or wireless access point (AP), the authenticator
controls the physical access to the network based on the authentication
status of the client.
• Authenticator includes a RADIUS client, which is responsible for
encapsulation and decapsulation of Extensible Authentication Protocol
(EAP) frames and interaction with the authentication server.
 Authentication server
• A server that performs the actual authentication of the client.
• Currently, a RADIUS server with EAP extensions is the only supported
authentication server.

Chapter 7
802.1X Port-Based Authentication Overview

Chapter 7
802.1X Configuration Example
 You will not be able to issue dot1x commands on the
interface if it is not set to switchport mode access prior.
 The default state of switch ports varies between switches,
but it is not commonly set to the access mode.

Chapter 7
Network Time
Protocols

Chapter 7
The Need for Accurate Time
 The need for accurate time is increasing year by year.
 Coordinating events, marking logs, and kicking-off scripts all
run based on a system clock.
 Therefore, in today’s network, coordination of system clocks
and their accuracy is increasing in importance.
 From a best practice perspective, it is recommended to set
clocks on all network devices to UTC regardless of their
location, and then configure the time zone to display the
local time if desired. In this manner, global operations can
fall back to UTC time for relative time.

Chapter 7
Configuring the System Clock Manually

Chapter 7
Setting Summer Time
 clock summer-time zone recurring [ week day
month hh:mm week day month hh:mm [offset]]
 clock summer-time zone date date month year
hh:mm date month year hh:mm [ offset ]
 clock summer-time zone date month date year
hh:mm month date year hh:mm [ offset ]

Chapter 7
Setting Summer Time

Chapter 7
Network Time Protocol Overview
 Manually setting the clocks of any network device is neither
accurate nor scalable.
 The best practice is to use Network Time Protocol (NTP), Simple
NTP (SNTP), or Precision Time Protocol (PTP)
 NTP is designed to synchronize the time throughout an entire
network infrastructure, including servers, switches, routers, host
machines, wireless access points, uninterruptible power supply
(UPS), and so on.
 NTP leverages UDP port 123 for both the source and destination
by default.

Chapter 7
Network Time Protocol Overview
 An NTP network usually gets its reference time from an
authoritative time source, such as a radio clock, GPS, or an
atomic clock attached to an NTP time server somewhere in the
network.
 NTP then distributes this time across the network.
 Accurate timekeeping is made possible by exchanging NTP
messages between each pair of machines (server/client) with an
association.
 However, in a LAN environment, NTP can be configured to use
IP broadcast messages instead.
 To keep accuracy of time, NTP uses the concept of a stratum to
describe how many NTP hops away a machine is from an
authoritative time source.
 A machine running NTP automatically chooses the machine with
the lowest stratum number

Chapter 7
NTP: Stratum
 NTP avoids in two ways synchronizing to a machine whose
time may not be accurate.
• NTP never synchronizes to a machine that is not synchronized itself.
• NTP compares the time that is reported by several machines and will
not synchronize to a machine whose time differs significantly from the
others, even if its stratum is lower.

Chapter 7
NTP Modes
 A device may take on more than one role at a time.
 Server
• Provides accurate time information to clients on the network.
 Client
• Synchronizes its time to an NTP server. This mode is most suited for
fileserver and workstation clients that are not required to provide any
form of time synchronization to other local clients. It can also provide
accurate time to other devices.
 Peers
• Peers only exchange time synchronization information.
 Broadcast/multicast
• Special “push” mode of NTP server where the local LAN is flooded
with updates; used only when time accuracy is not an issue.

Chapter 7
NTP Example

Chapter 7
Verify NTP

Chapter 7
Setting and Verifying the Clock Time Zone and
Daylight Savings Time

Chapter 7
Downstream NTP Example

Chapter 7
NTP Design Principles

Chapter 7
Securing NTP
NTP authentication steps:
 Step 1. Define NTP authentication key or keys with ntp
authentication-key command. Every number specifies a
unique NTP key.
 Step 2. Enable NTP authentication using the ntp
authenticate command.
 Step 3. Tell the Cisco device which keys are valid for NTP
authentication using the ntp trusted-key command. The
only argument to this command is the key that you defined
in the first step.
 Step 4. Specify the NTP server that requires authentication
by using the ntp server ip-address key key-number
command. You can similarly authenticate NTP peers by
using the ntp peer ip-address key key-number command.

Chapter 7
NTP Authentication Example

Chapter 7
NTP ACL’s
For NTP, you can configure the following four restrictions
through access lists:
 Peer
• Time synchronization requests and control queries are allowed. The
device is allowed to synchronize itself to remote systems that pass the
access list.
 Server:
• Time synchronization requests and control queries are allowed. The
device is not allowed to synchronize itself to remote systems that pass
the access list.
 Server-only
• Only allows synchronization requests.
 Query-only
• Only allows control queries.

Chapter 7
NTP Access List Example

Chapter 7
NTP Source Address
 The source of the NTP packet will be the same as the
interface the packet was sent out on.
 When implementing authentication and access lists, it is
good to have a specific interface set to act as the source
interface for NTP.
 It would be wise of you to choose a loopback interface to
use as the NTP source.
 This is because the loopback will never be down like
physical interfaces.
 If you configured loopback 0 to act as the NTP source for all
communication and that interface has, for example, an IP
address of 192.168.12.31, you can write up just one access
list that will allow or deny based on one single IP address of
192.168.12.31.

Chapter 7
NTP Versions
 NTPv4 is an extension of NTP Version 3. NTPv4 supports
both IPv4 and IPv6 and is backward compatible with
NTPv3.
NTPv4 adds the following capabilities:
 Support for IPv6
 Better security
 Leverages multicast over broadcast for push modes

Chapter 7
SNMP

Chapter 7
SNMP
This subsection covers the following topics related to SNMP:
 The role of SNMP
 Different SNMP versions
 Recommended practices for setting up SNMP
 Configuration examples for SNMP Version 3
 Verifying SNMP configurations

Chapter 7
SNMP Overview
SNMP systems consist of two
components, as follows:
 The SNMP manager that periodically
polls the SNMP agents on managed
devices by querying the device for
data. Periodic polling has a
disadvantage: A delay occurs between
an actual event occurrence and the
time the SNMP manager polls the
data.
 SNMP agents on managed devices
collect device information and translate
it into a compatible SNMP format
according to the MIB. MIBs are
collections of definitions of the
managed objects. SNMP agents keep
the database of values for definitions
written in the MIB.

Chapter 7
SNMP Process

Chapter 7
SNMP Versions
 Version 1
• Introduced five message types
• Get Request,
• Get Next Request
• Set Request
• Get Response
• Trap.
• This version is rarely used nowadays.
 Version 2
• Introduced two new message types
• Get Bulk Request to poll large amounts of data,
• Inform Request, a type of trap with expected acknowledgment on receipt.
• Version 2 added 64-bit counters to accommodate faster network interfaces.
• Added a complex security model, which was never widely accepted.
 Version 2c
• Community-based SNMP Version 2, is wide accepted
• Community-based version of SNMP is very unsecure.
 Version 3
• Methods to ensure the secure transmission of critical data between the manager and agent were
added.

Chapter 7
SNMPv3 Security
SNMPv3 supports the following three levels of security:
 noAuthNoPriv
• No authentication is required, and no privacy (encryption) is provided.
 authNoPriv
• Authentication is based on Hashed Message Authentication Code
(HMAC), MD5, or Secure Hash (SHA). No encryption is provided.
 authPriv
• In addition to authentication, cipher block chaining - Data Encryption
Standard (CBC-DES) encryption is used.

Chapter 7
SNMP Best Practices
 Restrict access to read-only.
 Use write access with separate credentials and careful
consideration.
 Set up SNMP views to restrict manager to only access
needed sets of MIBs.
 Configure ACLs to restrict SNMP access only by known
managers.
 Use SNMPv3 authentication, encryption, and integrity
where possible, including upgrading devices to support
SNMPv3 if necessary.

Chapter 7
SNMPv3 Configuration Steps
 Step 1. Configure an access list to be used to restrict
subnets for SNMP access.
 Step 2. Configure the SNMPv3 views to limit access to
specific MIBs.
 Step 3. Configure the SNMPv3 security groups.
 Step 4. Configure the SNMPv3 users.
 Step 5. Configure the SNMPv3 trap receivers.
 Step 6. Configure ifindex persistence to prevent ifindex
changes.

Chapter 7
SNMPv3 Best Practice Configuration

Chapter 7
SNMP Command Reference

Chapter 7
Chapter 7 Summary
 The AAA features include authentication, authorization, and accounting.
The use of AAA is required in nearly all campus networks because it
secures and provides administrative control and logging of user access to
network devices and to the network itself.
 Identity-based networking leverages protocols such as 802.1X to support
mobility, security, authentication, and authorization of users to network
resources.
 Accurate time is essential for time logging services in campus networks, as
are many security features like encryption.
 All Cisco Catalyst switches support NTP for time synchronization.
 NTP generally achieves millisecond accuracy in LAN networks.
 SNMP is a lightweight protocol that not only monitors and controls devices
but also supports alerting of events.
 SNMPv3 is the best practice recommendation for SNMP; avoid using
SNMPv2 (or v1) if it all possible (because of its lack of security features).
 Security around SNMP must be considered as part of any implementation
plan. At a minimum, use authentication and encryption along with restricted
write access and IP ACLs to restrict network access.

Chapter 7
 CCNPv7.1 SWITCH Lab7.1 NTP
 CCNPv7.1 SWITCH Lab7.2 SNMP
Chapter 7 Labs

Chapter 7

Chapter 7
Acknowledgment
• Some of the images and texts are from Implementing Cisco IP Switched
Networks (SWITCH) Foundation Learning Guide: (CCNP SWITCH 300-115) by
Richard Froom and Erum Frahim (1587206641)
• Copyright © 2015 – 2016 Cisco Systems, Inc.
• Special Thanks to Bruno Silva

CCNP Switching Chapter 7

More Related Content

What's hot (20)

Similar to CCNP Switching Chapter 7 (20)

More from Chaing Ravuth (9)

Recently uploaded (20)

CCNP Switching Chapter 7