THD Analysis in Multilevel Inverter Fed Induction Motors Using Particle Swarm Optimization

Heena Manhas et al. Int. Journal of Engineering Research and Applications www.ijera.com
ISSN: 2248-9622, Vol. 5, Issue 9, (Part - 1) September 2015, pp.69-72
www.ijera.com 69 | P a g e
THD Analysis in Multilevel Inverter Fed Induction Motors Using
Particle Swarm Optimization
Heena Manhas1
, Baljit Singh2
, Gagandeep Sharma3
M tech Student1
, DAV Institute of engineering and technology, Jalandhar
Assistant professor2
Assistant professor3
ABSTRACT
Harmonics measurement of an industrial unit is done to aid the power quality aspects in a typical factory. The
real issues are the harmonics generated by the inverters which affects the induction machine performance.
Several inverters like Voltage Series Inverters, PWM fed Inverters, Multilevel inverters etc. exist in literature.
Amongst all these, multilevel inverters have been very popular due to its several advantages. But there is a
challenge of optimal design of the inverter and optimal selection of pulse width of each level so as to get
minimal Total Harmonic Distortion. For these reasons a novel multilevel inverter design based on Particle
Swarm Optimization is proposed in this paper for obtaining the optimal width of the pulse of each level so as to
get minimal Total Harmonic distortion. The results has been compared to that of the existing techniques and
found to be quite better than the existing ones.
Index Terms— Particle Swarm Optimization, cascaded Multilevel Inverter (CMLI), Induction Motor, Multi-
level Inverter (MLI)
I. INTRODUCTION
In various industrial applications, usually, DC
motors were the work horses for the adjustable Speed
Drives (ASDs) due to their excellent speed and
torque response. But, they have the intrinsic
disadvantage of commutator and mechanical brushes,
which endure wear and tear with the passage of time.
Mostly AC motors are preferred to DC motors,
mostly, an induction motor due to its low cost, low
maintenance, lower weight, higher efficiency,
improved ruggedness and reliability. All these
features make the use of induction motors necessary
in many areas of industrial applications. The
advancement in Power electronics and semi-
conductor technology has encouraged the
development of high power and high speed
semiconductor devices in order to attain a smooth,
continuous and step less variation in motor speed.
Applications of solid state converters/inverters for
adjustable speed induction motor drive are wide
spread in electromechanical systems for a large
spectrum of industrial systems. Modified CSI based
induction motor drive is given by Gopukumar [1].
Multilevel inverter modulation schemes to eliminate
common mode voltage is given by Zhang, 2000.
Modulation schemes for six phase induction motor
are given by Mohapatra [2]. Active harmonic
elimination for multilevel inverters is given by
Tolbert [3]. The inverters are either Current Source
Inverter (CSIs) or Voltage Source Inverters (VSIs).
Current source inverters are widely used for the
application of fully generative induction machine
variable speed drives. An important and attractive
feature of CSI is its good fault protection capability
and the inherent regeneration capability. But, CSI-fed
induction motor suffers from severe torque
pulsations, especially at low speeds, which manifest
themselves in cogging of the shaft. The usual
technique of overcoming such problems in Voltage
Source Inverters (VSIs) is to pulse width modulate
the input voltage waveforms. Pulse width modulated
voltage source inverters are invariably used for
AC/DC/AC conversion to provide a variable ac
voltages to the induction motor. However, inverter
fed induction motor suffers from the presence of
significant amount of harmonics which causes
undesired motor heating, torque pulsation and EMI
[4]. The reduction in harmonics calls for large sized
filters, resulting in increased size and cost of the
system However, the advancements in the field of
power electronics and microelectronics made it
possible to reduce the magnitude of harmonics with
multilevel inverters, in which the number of levels of
the inverters are increased rather than increasing the
size of the filters [5]. The performance of multilevel
inverters will be better than a classical inverter. The
THD for multilevel inverters will be lower than that
of a classical inverter [6].
This paper aims at designing of a multilevel
inverter based on an Improved Particle Swarm
Optimization technique [10] for reduction of
harmonics in induction motor control.
Section 2 describes theory of cascaded multilevel
inverter. Section 3 describes harmonic elimination in
RESEARCH ARTICLE OPEN ACCESS

multi-level inverters. Section 4 introduces our
methodology and discusses the implementation of
our proposed algorithm. Section 5 shows the results
of our approach and finally Section 6 concludes the
paper with a discussion on the future scopes of this
method.
II. POWER TOPOLOGY OF
CASCADE MULTILEVEL
INVERTERS
Cascaded Multilevel Inverter (CMLI) topology
is the most advantageous topology in the family of
multilevel inverters. It needs less number of
components as compared to diode-clamped and
flying capacitors type multilevel inverters. It has
modular structure with easier switching Strategy and
occupies less space [7] - [8].Fig. 1(a) shows the
structure of a single-phase H-bridge cascaded
multilevel converter topology that is used to
synthesize a 2s + 1 staircase output waveform. Fig.
1(b) also shows the staircase voltage waveform
produced by multilevel converters.
Fig.1. (a) Topology of a single-phase cascaded
inverter (b) Staircase output phase voltage
A cascaded H-bridge multilevel converter
comprises of some SDCS. The advantage of this
topology is that the modulation, control, and
protection requirements of each bridge are modular.
It should be pointed out that, unlike the diode-
clamped and flying-capacitor topologies, isolated dc
sources are required for each cell in each phase. The
number of output-phase-voltage levels in a cascade
multilevel inverter is 2s + 1, where s is the number of
SDCSs. To obtain the three-phase configuration, the
outputs of three single-phase cascaded inverters can
be connected in Y or Δ.
III. HARMONIC ELIMINATION IN
MULTILEVEL INVERTER
Harmonics are unwanted current or voltage
[9].They exist at some integer multiple or fraction of
the fundamental frequency. The harmonics orders
and magnitude depend on the inverter topology and
the modulation technique, for example in single
phase VSI, only odd harmonics are present in the
output voltage waveform. The even harmonics are
absent due to the half wave symmetry of the output
voltage harmonics. For three phase VSI, in addition
to the even harmonics triplet (third and multiple of
third harmonics) are also absent. The output voltage
V (t) as in eqn. 1 of the multi-level inverter can be
expressed in Fourier series as:
V (t) = (𝑎 𝑛
∞
𝑛=1 𝑠𝑖𝑛𝑛α+𝑏 𝑛 𝑐𝑜𝑠𝑛𝛼) … (1)
Even harmonics are absent (𝑏 𝑛 =0) due to quarter
wave symmetry of the output voltage and only odd
harmonics are present. The amplitude of the nth
harmonic an is expressed only with the first quadrant
switching angle𝛼1,𝛼2, 𝛼3 …….. 𝛼 𝑚 as shown in
eqn.(2) and (3).
𝑎 𝑛 =
4 𝑉 𝑑𝑐
𝑛𝛱
𝑐𝑜𝑠𝑛𝛼𝑘 …∞
𝑘=1 (2)
0<𝛼1 <𝛼2 <𝛼3 < … 𝛼 𝑚 < π/2 …(3)
For any odd harmonics can be expressed up to kth
term where m is the number of variable
corresponding to switching angle α1 through αm of
the first quadrant. THD expression is shown as in
eqn. (4)
THD=
1
fundamental
…… (4)
= 𝑛𝑡ℎ ℎ𝑎𝑟𝑚𝑜𝑛𝑖𝑐 𝑐𝑜𝑚𝑝𝑜𝑛𝑒𝑛𝑡 2∞
𝑛=1 ]2
IV. PROPOSED METHODOLOGY
Proposed methodology for the problem
discussed in Section 3 is mentioned. The technique
Particle Swarm Optimization for multilevel inverter
has been applied on the induction motor model and
then their performance was compared on the basis of
Total Harmonic Distortion, machine performance etc.
4.1 Particle Swarm Optimization (PSO)
Kennedy and Eberhart [10] first introduced PSO
in 1995 as a new heuristic method. Basically, the
PSO was inspired by the sociological behaviour
associated with swarms such as flocks of birds and
schools of fish. The individuals in the population are
called particles. Each particle is a potential solution
for the optimization problem and tries to search the
best position through flying in a multidimensional
space. The sociological behaviour which is modelled
in the PSO system is used to guide the swarm, hence
probing the most promising areas of search space.
The movement of each particle is governed by the
efficiency of their own previous position and that of
the neighbours. Each particle can be described by two
parameters- position (xi) and velocity (vi), which is
updated by the following rule:
𝑣𝑖 𝑡 + 𝑑𝑡 = 𝑤∗
𝑣𝑖 𝑡 + 𝑐1 𝑟1(𝑝𝑏𝑒𝑠𝑡𝑖(𝑡)) − 𝑥𝑖 𝑡 +
𝑐2 𝑟2(𝑔𝑏𝑒𝑠𝑡𝑖(𝑡)) − 𝑥𝑖 𝑡
𝑥𝑖 𝑡 + 𝑑𝑡 = 𝑥𝑖 𝑡 + 𝑣𝑖 𝑡 𝑑𝑡
Here, pbesti is the best position obtained by
𝑖𝑡ℎ particle and gbest is the best position obtained by
any particle till current iteration. c1, c2 are known as
acceleration vectors whereas r1, r2 are two random
vectors uniformly distributed between “0” and “1”
and w denotes inertial weight.

4.2 Modification with PSO of Induction Motor
For better search, acceleration vectors c1 and c2
should be retained small, which however decreases
the convergence rate and has to be selectively chosen
varying from application to application. For a
problem having large numbers of local extrema, the
values of c1 and c2 should be kept low, so as to
increase the chance of finding the global extrema at
the cost of convergence time and vice-versa.
Similarly, the inertial weight w is adjusted,
depending on the amount of influence desired in a
particles previous position on its current movement.
This optimization algorithm is finally said to
converge, when each particle reaches the global best
or the preset extremum value of the cost function.
V. SIMULATION RESULTS AND
DISCUSSION
All the simulations were prepared in MATLAB
R2013, 2.7GHz processor with 4 GB RAM. The
proposed model of Multilevel Inverter fed Induction
Motor was designed in Simulink as shown in Fig 2.
Figure 2: Complete Design of Multilevel Inverter fed
Induction Motor model using PSO
Figure 2 shows the complete model of the
multilevel inverter fed induction motor, tuned by
Particle Swarm optimization. The PSO is employed
using MATLAB s-function and is operated for the
tuning of firing angles after taking feedback from the
calculated THD.
Fig. 3 Complete Design of Multilevel Inverter fed
Induction Motor model without PSO
Fig. 3 shows the complete model of the multilevel
inverter fed induction motor, without Particle Swarm
optimization. THD analysis is done without using
any algorithm.
Figure 4: Individual components of H-Bridge
Inverter
Figure 4 shows the individual H-bridge inverter
which is implemented and cascaded using subsystem
in the main model. The output of the individual
inverters is kept around 8V.
Figure 5: Output of Multilevel inverter
Figure 5 shows the motor voltage when PSO
algorithm is applied and is compared to the reference
sine wave. The total Harmonic distortion is found to
be 8.03% without using PSO while it comes down to
6.9% when PSO algorithm is applied.
Algorithm Without PSO With PSO
THD Value
(%)
8.03% 6.9%
The THD has been taken as the optimization
function for the Particle Swarm Optimization. The
PSO is implemented by generating random particles
in the given range and updating each particle suing

the update rule of PSO. The best position of each
particle is found out and called pbest and the best of
all pbest is called as gbest.
Fig 6: Simulation results of currents, capacitor
voltage, electromagnetic torque, and rotor speed of
Induction Motor using PSO.
VI. CONCLUSIONS AND FUTURE
SCOPE
PSO (Particle swarm optimization) based
harmonic elimination technique has been applied in
this paper for control of induction motors and the
various simulations has been performed on Simulink.
The results have been shown and it is supposed that
the use of PSO improves the performance and also
the multilevel inverters have an edge over other
designs due to their design simplicity and
performance. In future, other algorithms can be
implemented for the same problem and other
configurations of inverters can be verified. Further,
better objective functions can be considered and
effect of other parameters can be considered in
future.
REFERENCES
[1] Gopukumar K, Biswas SK, Satish Kumar S
and Joseph Vithyanthil. “Modified current
source inverter fed induction motor drive
with reduced torque pulsation”. IEEE Proc.
313(4): 150-164 1984.
[2] Mohapatra. KK, Gopukumar K,
Somashekhar VT and Umanand L. “ A
Modulation scheme for six phase induction
motor with an open-end winding”. 25th
Annual Conference IECON 02, Spain. pp.
810-815 2002.
[3] Zhong DuLeon, M. Tolbert and John N.
Chiasson. “ Active Harmonic Elimination
for Multilevel Converters”. IEEE
Transactions on Power Electronics. 21(2):
459-469 2006.
[4] Shivakumar E.G, Gopukumar K, Sinha S.K
and Ranganathan V.T, “ Space vector PWM
control of dual inverter fed open-end
winding induction motor drive”. IEEE
APEC Conf. 1: 399-405 2006.
[5] Juan Dixon and Luis Mora, “ High-Level
Multi-step Inverter Optimization Using a
Minimum Number of Power Transistors”.
IEEE Transactions on Power Electronics.
21(2): 330-337 2006.
[6] Chunmei Feng and Vassilions G Agelidis, “
On the Comparison of fundamental and high
frequency Carrier based techniques for
multilevel NPC Inverters”. IEEE PES Conf.
2: 520-525 2002.
[7] Jih-Sheng Lai, Fang Zheng Peng,
“Multilevel Converters- A New Breed of
Power Converters”, IEEE Trans. On
Industry Applications, vol. 32, no. 3, pp.
509-517, May/June 1996.
[8] Fang Zheng Peng, Jih-Sheng Lai, et al, “A
Multilevel Voltage-Source Inverter with
Separate DC Sources for Static Var
Generation”, IEEE Trans. on Industry
Applications, vol. 32, no. 5, pp. 1130-1138,
September/October 1996
[9] A. K. Ali Othman “Elimination of
harmonics in multi-level inverter with non-
equal DCsources using PSO”.IEEE conf.
proce EPEPEMC2008.
[10] Kennedy, James. "Particle swarm
optimization." Encyclopedia of Machine
Learning. Springer US, 2010. 760-766.

THD Analysis in Multilevel Inverter Fed Induction Motors Using Particle Swarm Optimization

More Related Content

What's hot (17)

Viewers also liked (18)

Similar to THD Analysis in Multilevel Inverter Fed Induction Motors Using Particle Swarm Optimization (20)

Recently uploaded (20)

THD Analysis in Multilevel Inverter Fed Induction Motors Using Particle Swarm Optimization