The Intellectual Automated Substation

@ IJTSRD | Available Online @ www.ijtsrd.com | Volume – 2 | Issue – 3 | Mar-Apr 2018 Page: 1652
ISSN No: 2456 - 6470 | www.ijtsrd.com | Volume - 2 | Issue – 3
International Journal of Trend in Scientific
Research and Development (IJTSRD)
International Open Access Journal
The Intellectual Automated Substation
Zhalilov Rashid
Ph.D, Associate Professor,
Department of Electrical Engineering
Bukhara engineering – Technological institute, Uzbekistan
ABSTRACT
The article is devoted to the study and introduction of
modern technologies in electro-technical branch
of the industry for the purpose of increasing
reliability of electric supply. Appling the latest
technical developments marketed in automatic
breakers Compact NS and Master pact of the
company "Schneider Electric", for modernization
distributing device 0,4 kV applied transformer
substation is offered in it .
Keywords: Schneider Electric, Compact NS , Master-
pact, SCADA, the programmed logic controller ,
reliability of electrical supply,cases the low-voltage
transformer,four wire electric network TN-C,
recommended IEC three-phase five-wire network TN-
S, microcontacts OF, SDE, PF, CH, Modbus, SCADA,
Batibus.
INTRODUCTION
Introduction of systems of automation and dispatching
management on the modern digital techniques radical
raises in the image quality and reliability of processes
of manufacture, transfer and distribution electric
power [1]. As a result of equipment of power objects
by systems automations , microprocessor means
emergency-preventive automatics and relay
protection reach essential economic benefit at the
expense of optimization of modes of transfer and
distribution of energy, prevention of emergencies and
minimization of a damage in case of their occurrence
[1,2,3] .
At present the begun transition in abroad to the next
generation of microprocessor (digital) device of relay
protection and automatics (DRPA) with integration
within the limits of a uniform complex functions of
relay protection, measurement processor complexes
which have received wide applicated and commercial
account electric power, regulation and management of
electrical installation it is directed on maintenance of
increase of reliability of electrical supply of
consumers and conformity to modern safety
requirements on IEC [2]. Frequent relay protection
terminals carry out function of controllers of the
bottom level of the automated management systems
(AMS), providing complex protection of management
of substations at modern level. In this case they
provide management in a place or from remote
control offices, control of position of the primary
equipment, measurement, the alarm system,
record and transfer of oscillograms. Besides, the AMS
information system al lows to make to the user
record/change date with use the pass word, to receive
reports and to conduct archive of events, to execute
conditions of diagnostics of the primary equip
ment and etc.[4]. Wide use in electrical installations
of consumers of servers of control systems of real
time ( SCADA) provides [2,4]:
 teleinformation reception/transfer in any reports;
 reception / data transmission of the daily
dispatching sheet (DS);
 processing of the arriving information,
formation date bases (DB) of real time
(DBRT), to condense;
 management of a dispatching board (digital
devices, symbols, mnemonic schemes,
information displays);
 the cyclic copying DBRT on files-servers of a
local network (LN) and etc.

International Journal of Trend in Scientific Research and Development (IJTSRD) ISSN: 2456-6470
As it is marked in [1-3], in the report 34-108 СIGRE
are answered to Dews of a combination of traditional
control facilities, relay protection and automatics
(DRРА) with the new microprocessor complexes
which have received wide application in the world.
Creation is thus provided: microprocessor systems of
registration of emergency events, gathering and data
processing about work RРА; systems of
communications of new complexes with computer
"kernel" of the integrated monitoring system and
management, and also systems of display of the
information on workplaces of operation personnel and
the personnel of services RРА.
Distinctive feature developed by us distributing
device -DD-0,4 kV for complete transformer
substation (CTS) is the modern design, an openness
for AMS for the account of presence of ports and the
applications of the software that allows to realize
flexible technical and economic solving for an
electrical supply of consumers of any category. The
device carries out functions local or remote control,
relay are sewn up, alarm systems, automatics,
registration, control of harmonics in a voltages curve
(in cells of input from a reserve source), diagnostics
automatic breakers, and also necessary blocking
various blockings CTS. The switching centre- DD-0,4
kV CTS gathers from low-voltage cases of
type Cases low-voltage transformer (CLVT). For
assemblage of sections of tires DD-0,4 kV CTS
separate CLVT, two party service, rigidly fasten
among themselves the folding connections.
In cells CLVT in the main chain following devices are
established:
 in cells of departing joining - automatic breakers
(АВ) manufactures Schneider Electric Compact
NS 400 N on 400 A to roll out executions with
the electric drive;
 in section and cells of input from the transformer -
automatic breakers manufactures Schneider
Electric Master pact NT 16 H1 on 1600 A to roll
out execution with the electric drive;
 in cells of input from a reserve source - automatic
breakers of manufacture Schneider Electric
Master pact NT 10 H1 on 1000 A to roll out
execution with the electric drive;
 a source of an uninterrupted food (UPS) (UPS
NetPro 19) capacity 1кVt.) with time of support of
capacity of consumers not less 5 minutes.
In cell RРА of the section breakers are established
various microprocessor blocks of relay protection, or
programmed logic controllers (PLC) at will of the
customer, for example S7-300 (the manufactures
Siemens). On fig. 1 basic one-linear scheme CTS with
it is developed us DD-0,4 kV.
In DD-0,4 kV the following algorithm of automatics
CTS is realized (fig. 1):
 on the section breakers (SВ) it is executed
automatic input of a reserve food (AIRBF) - a
normal mode - both introduction breakers from
transformers are included, SВ it is disconnected.
On voltage disappearance on one of inputs (voltage
control is carried out directly on tires CTS) - through
the set endurance of time the breakers is disconnected
corresponding introduction.
Upon switching-off of input, absence of voltage on
the disconnected section of tires and voltage presence
on the second section, joins SB. At switching-off of
the introduction breakers on currents protection the
signal on a start-up interdiction is given of AIRBF.
The algorithm of start of a reserve source (is carried
out by the independent automatical Diesel power
station (АDPS):
In a starting position both introduction breakers from
a transformers one of the introduction breakers is
included, the generating switch in van АDPS is
disconnected.
At voltage disappearance on two sections CTS
(voltage control it is made directly on tires) the signal
on start АDPS is formed, at occurrence of voltage
from АDPS, both introduction breakers are
disconnected CTS, upon their switching-off the signal
is formed on inclusions generating breakers are
ADPS.
 For realization of automatic and manual return
transition to a food Automatic return transition»,
having two position: "Auto" and «The manual.».
Algorithm of return transition.
At voltage occurrence on one of inputs, with set date
time (1-30 minutes), are formed a signal normal to
stopping АDPS. Thus is disconnected generating
breakers ADPS, upon its switching-off, presence
voltage on input to the introduction switch of one of

section of tires (ST), to the absence fact voltage on
ST, to the fact of the disconnected condition of the
introduction switch adjacent section without
endurance of time the switch of that joins introduction
ST on which input there was voltage. At voltage
occurrence on other input, with set date time (1-30
minutes), upon presence of voltage to the introduction
switch of this ST, the included condition of the
introduction switch and voltage presence on adjacent
ST, it is disconnected SВ and the switch of the second
joins introduction Input. Thus scheme АIRВ comes
back in a starting position.
The choice of a priority of inclusion of the
introduction breaker is carried out with set date time
on inclusion. At voltage occurrence simultaneously on
both inputs - by the first input with smaller date time
joins.
One more feature developed DD-0,4 kV is that taps
«The automatic breakers - a departing cable to
consumers» are deduced in the bottom part of a case.
On the ends tires (each all taps and the ends are
marked (a phase, № the cells, a departing feeder). For
safety of attendants cases CLVT are divided into the
isolated compartments: the tires a compartment,
compartment with breakers, compartment of relay
protection and automatics. In the tires a compartment
the equipment of the main chains settles down: the
power the tires departing to consumers and a reserve
source power cables and transformers of a current.
Power automatic switches and switches of chains of
management are established in corresponding cells.
In cells of input from the transformer (cell № 1 in a
case №1 and cell № 2 in a case №5) under a
compartment for power switches it is allocated the
special sector for installation of a source of an
uninterrupted food (UPS) (UPS NetPro 19 capacity
of 1 kVt.) with time of support of capacity of
consumers not less minutes.
In is the requirement on maintenance of speed of
switching-off of the damages connected with
influence on the person. In a compartment of relay
protection are established: the interface relays of the
alarm system, blocking and automatics, PLC, devices
of control and the account of the electric power and
other. Cells inside CLVT are separated from each
other metal a partitions. For carrying out of repair
work and maintenance service the power to roll out
executions automatic breakers are established in cells
on not-mobile the chassis fixed in working position
bolt connection supported on the basis of a cell.
1
3
2
14
10
11
6 98
4
5
12
13
7
Fig-1: One-linear the principle scheme CTS.
Symbols are accepted, on the scheme the following : 1
high-voltage input- 1 from the closed distributing
device of voltage 6-10 кV ; 2- the transformer №1 of
voltage 6-10 /0.4 кV, capacity 1000 кVА; 3- input- 1
0.4 кV from transformer In = 1600 A; 4- high-voltage
input- 2 from transformer In = 1600 A; 5-the

transformer №2 of voltage 6-10 /0.4 кV, capacity
1000 кVА; 6- input- 2 0.4 кV from transformer In
= 1600 A; 7- section automatic breakers In = 1600 A
; 8- section of tires № 1; 9- Section of tires № 2; 10-
automatic diesel power station (АDPS) rated current
of In = 1250 A; 11- automatic breakers the generating
of АDPS; 12- input- 1 0.4 кV from the АDPS; 13-
input- 2 0.4 кV from the АDPS; 14- bunch of power
cables 4х (КВБШв - 3х150+1х50).
CLVT on the back party has two doors: top – closing
access in compartment of modular tires and bottom
closes a zone of departing power cables and bottom
closes a zone of departing power cables.
For possibility of control over a power consumption,
management electrical Consumption, accumulation of
the information on loadings of sections of tires CTS,
integration of automatic switch Master pact NT H1
into scheduling systems uses additional function of data
transmission (communication Bus) COM, realized in
section, cells of
input from the transformer and from a reserve source,
АВ Master pact NT [5]. For these to roll out devices
additional function of data transmission is provided
(fig. 2)
The module of communication established in the
device, delivered together with group of contacts
(microcontacts OF, SDE, PF, CH) and the complete
set of communication with electromagnets of
management XF and MX
 the module of communication established in the
chassis, delivered together with group of contacts
(contacts CE,CD, CT).
Each established device has the address which is
appropriated to it by means of the keyboard of the
block of control and management Micrologic
(Modbus) or remotely (Batibus). Thus at creation
automated management systems of the enterprise it is
possible from Information operating system of top
level , for example from mini enterprise COMPUTER
scheduling office , management (or through PLC, or
passing it) established on feeding substations AV, to
transfer in top level of the data of measurement, the
alarm system, automatics, registration, control of
harmonics in a pressure curve, and also other
necessary information, for example condition АВ of
switches in various joining CTS, voltage presence on
inputs and sections of tires CTS etc.
Fig. 2. The scheme of connection of additional function of data transmission COM .

Conclusion
1. With a view of creation of the automated control
systems by industrial power supply, in particular an
electrical supply, workings out more perfection
methods of optimization of power modes, increases
adequacy and security of electrical supplies etc. it is
necessary to expand use sphere in of electrical
installations consumers of servers of control systems
of real time (SCADA).
2. DD-0,4 kV CTS, equipped with PLC, automatic
breakers the manufactures Schneider Electric Master
pact with block of the control and management
Micrologic A/P/H can carry out function of bottom
level automated management systems of electric
power, complex protection of management of
substations at modern level. In this case they provide
automatic control in a place or with the removed
control offices, control of position primary
installations, measurements, the alarm system, record
and transfer of oscillograms etc.
3. In development of the theory and perfection of
methodology of designing of systems electrical
supplies industrial company the important place
occupies the account in such workings out available in
present time in electrical installations of consumers
and introduced in practice of operation of modern
devices DRPA, micro-processor systems of
registration of emergency events, gathering and data
processing about work DRPA; systems of
communications of new complexes with computer
"kernel" of the integrated monitoring system and
management, and also systems of display of the
information on workplaces of operation personnel and
a personnel of services RPA
4. And necessary for such workings out conformity to
modern safety requirements on IEC, IEE is important.
At reconstruction maintained, and also designing of
new electric networks it is necessary to aspire to pass
on three-phase five-wire network TN-S recommended
to СIGRE, IEC.
REFERENCES:
1) Design of a digital protection scheme for power
transformers using optimal state observers/ Y.V.
Multy et al.// IEE Proceedings- C, N 3, pp.224-
230, 1988.
2) Rudenko J.N., Semenov V. A/Automation of
dispatching management in electrical power. М:
Publishing house MEI. pp. 648, 2000.
3) Zhalilov R. B. Preconditions of creation of the
automated control systems of industrial power
supply.// The chief electrical engineer, release 6,
pp. 41-43, 2006.
4) Zhalilov R. B. Preconditions to creation of the
intellectual automated substation..//Industrial
power, release 4, pp. 15-18, 2008 .
5) Merlin Gerin. Automatic switches and switches of
loading for capacities transfer in low voltage
networks. Masterpact NT and NW. The catalogue.
М: the centre of information support, 2007.

The Intellectual Automated Substation

More Related Content

What's hot (20)

Similar to The Intellectual Automated Substation (20)

More from ijtsrd (20)

Recently uploaded (20)

The Intellectual Automated Substation