Travel Assistant For Blind With Dynamic User Input For Location Based Alerts Using ARM7 And XBee (SYNOPSIS)
0 likes15 views
The document outlines the development of a portable electronic travel aid for the blind, utilizing ARM7 technology and Zigbee communication for location-based alerts. It describes the hardware and software requirements, operational methodology, and key functionalities aimed at enhancing independent mobility for visually impaired users. Additionally, it discusses the advantages and disadvantages of the technology, as well as potential applications in various mobility-restricted environments.
Travel Assistant For Blind With Dynamic User Input For Location Based Alerts Using ARM7 And XBee (SYNOPSIS)
- 1. 2. Travel Assistant for the Blind with Dynamic User Input For Location-Based Alerts Using ARM7 And Zigbee Introduction: The goal of the Blind Aid project is to develop navigational assistance technology for the blind or visually impaired. Specifically, we seek to develop a portable Electronic Travel Aid (ETA) for visually impaired users, along with the accompanying radio frequency identification (RFID) localization infrastructure used to equip buildings. The major problem the visually impaired experience is trouble with indoor navigation in unfamiliar buildings. Imagine the wide open spaces in an airport concourse; even if there are Braille signs at the counters, the blind may not be able to find them. Blind people use moving ramps, escalators, revolving doors, and turnstiles with as much ease as any sighted person. When encountering stairs, it simply isn't necessary to explore each step. The cane tip is used primarily to detect the beginnings and ends of stairways. In either case, it is a good idea to hold the cane in a manner that would not trip a fellow pedestrian. One of the major goals for blind and visually impaired people is independent mobility. Mobility aids like walking sticks and guide dogs are commonly used by the blind even today. With the advances of modern technologies, many different types of devices are available to support the mobility of the blind. These mobility aids are generally known as electronic travel aid.
- 2. Block Diagram: LOCATION INFORMATION TRANSMITTER RECEIVER STAGE GND LCD DISPLAY HARDWARE REQUIREMENTS: ARM 7 / Cortex M3, LCD, Relay Driver, Relays, Resistors, Capacitors, LEDs, Crystal, Diodes, Transformer, Voltage Regulator, Push Button. SOFTWARE REQUIREMENTS: Keil compiler uVision 4, Language: Embedded C or Assembly, WLPRO Programmer 230 V, AC Supply TRANSFORMER RECTIFIER FILTER REGULATOR +12 Volts +5 Volts XBEE TX ARM PROCESSOR KEY INPUTS
- 3. Receiver: BUFFER DRIVER RELAY LCD DISPLAY ARM PROCESSOR OR OR M VISUAL INDICATION VOICE DC MOTOR OUTPUT DEVICES XBEE RX
- 4. Block diagram explanation Power supply unit This section needs two voltages viz., +12 V & +5 V, as working voltages. Hence specially designed power supply is constructed to get regulated power supplies. Switches: In electrical engineering, a switch is an electrical component that can break an electrical circuit, interrupting the current or diverting it from one conductor to another. A switch may be directly manipulated by a human as a control signal to a system. Automatically operated switches can be used to control the motions of machines. ARM processor ARM is a computer processor-based RISC architecture. A RISC-based computer design approach means ARM processors require significantly fewer transistors than typical processors in average computers. This approach reduces costs, heat, and power use. The low power consumption of ARM processors has made them very popular: The ARM architecture (32-bit) is the most widely used in mobile devices, and the most popular 32-bit one in embedded systems. Zigbee Technology ZigBee is a specification for a suite of high-level communication protocols used to create personal area networks built from small, low-power digital radios. ZigBee is based on an IEEE 802.15 standard. Though low-powered, ZigBee devices can transmit data over long distances by passing data through intermediate devices to reach more distant ones, creating a mesh network. Buffers
- 5. Buffers do not affect the logical state of a digital signal (i.e. a logic 1 input results in a logic 1 output whereas logic 0 input results in a logic 0 output). Buffers are normally used to provide extra current drive at the output but can also be used to regularize the logic present at an interface Drivers This section is used to drive the relay where the output is the complement of input which is applied to the drive but the current will be amplified Relays It is an electromagnetic device that is used to drive the load connected across the relay and the o/p of the relay can be connected to the controller or load for further processing. Voice recorder: The aPR33A series are powerful audio processors along with high-performance audio analog-to-digital converters (ADCs) and digital-to-analog converters (DACs). The aPR33A series is a fully integrated solution offering high performance and unparalleled integration with analog input, digital processing, and analog output functionality. High- quality audio/voice systems with lower bill-of-material costs can be implemented with the aPR33A series because of its integrated analog data converters and a full suite of quality-enhancing features such as sample-rate converters. In this messages must be recorded or played back sequentially, specially designed for simple key triggers, the user can record and playback the message. Meanwhile, this mode provides a power-management system.
- 6. DC motor: A DC motor relies on the fact that magnet poles repel and unlike magnetic poles attract each other. A coil of wire with a current running through it generates an electromagnetic field aligned with the center of the coil. By switching the current on or off in a coil its magnetic field can be switched on or off or by switching the direction of the current in the coil the direction of the generated magnetic field can be switched 180°. Indicator: This stage provides a visual indication of which relay is actuated and deactivated, by glowing respective LED or Buzzer. Methodology: This project is developed for the blinds to find out the location of the place where they are. The main modules in this project are Zigbee, ARM controller unit, and Voice signal as an output. The transmitter will be there with a blind and the receiver will be there at the location. The transmitter module has Switches, an ARM controller, and Zigbee as a communication media. The receiver has Zigbee, an ARM controller, and a voice-operated device. If a Blind Presses a Switch to know the location, that information will be given to the ARM controller, then the ARM controller analyses the signal and sends information to the receiver which is present in the location via Zigbee. At the receiver, the Zigbee receives a signal which was transmitted from the transmitter and sends that to the ARM controller. After receiving the signal the ARM controller will activate the proper voice chip to provide a corresponding voice signal.
- 7. Advantages: 1. Secure and reliable communication. 2. Leading-edge technology that meets today's and tomorrow's needs. 3. This not only detects the obstacles but can also guide the user around them. This combination of obstacle detection and avoidance reduces the conscious effort required from the user. 4. Continuous scanning of the environment relieves the user from additional actions, therefore reducing the required physical and mental effort. 5. This can provide the user with a panoramic view of the environment, covering a sector of 120 degrees. Disadvantages: 1. One-time investment cost. 2. It has to be planted throughout the city. Applications: 1. This project can be implemented to increase the independent mobility of blind and elderly travelers 2. Restricted zones. 3. Wherever mobility is important there we can implement this project.