Ultra sonic testing of weldjoints prepared at different voltage and current

IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
__________________________________________________________________________________________
Volume: 02 Issue: 11 | Nov-2013, Available @ http://www.ijret.org 738
ULTRA SONIC TESTING OF WELDJOINTS PREPARED AT DIFFERENT
VOLTAGE AND CURRENT
Vivek Varia1
, Yash Ganatra2
1, 2
School of Mechanical and Building Sciences, Vellore Institute of Technology
varia.vivekvimal@gmail.com, gyash1992@gmail.com
Abstract
There are several millions of weld joints made at every corner of the world. There are chances that safety may be ceased to exist
because of some defects in the weld joints. The objective of this investigation was to verify the influence of current and voltage on
porosity found inside weld joints and other visual defects. Non - Destructive testing was carried out for standard butt joint from
Manual metal arc welding (stick welding) and Gas metal arc welding. Porosity was measured in terms of depth from the surface of
weld joint. The results will be presented in this paper with interesting finding with test sample by different welding technique.
Keywords: Non-Destructive Testing, Stick Welding, Gas Metal Arc Welding, Butt Joint.
------------------------------------------------------------------------***----------------------------------------------------------------------
1. INTRODUCTION
There are thousands of weld joints made using different
welding techniques. Although these welding techniques are
well proven there might be possibility of defect which may
create a problem. For this reason Ultra-Sonic testing of weld
joints is carried out.[1]
Welding joints are made setting
different parameters like current, voltage and welding speed.
This paper primarily focuses on welding current and voltage.
2. LITERATURE STUDY
Ultrasonic testing (UT) is a non-destructive inspection method
that uses high frequency sound waves (ultrasound) that are
above the range of human hearing, to measure geometric and
physical properties in materials.[2] Ultrasound travels in
different materials at different speeds (velocity). However, the
speed of sound propagation in a given material is a
constant.[10] There are several ways that sound travels
through a material. One type of sound wave, called
longitudinal or compression travels about 330 meters per
second in air and about 6400 meters.[3]
The elements that are common in every NDT Test are:[9]
a. Some source of probing energy or probing medium
b. Discontinuity that causes a change In the probing
medium.
c. Some source of detecting the change
d. Some means of indicating the change
e. Some means of recording the change so that
interpretations can be made.
The Ultrasonic testing is based on the fact that solid materials
are good conductors of sound waves, whereby they are
reflected not only from the surface but also from the internal
flaws.[5] The interaction of sound waves with material is
stronger when wavelength is smaller. The piezoelectric
element excited by an extremely short electrical discharge
transmits an ultrasonic pulse. The same element generates an
electric signal when it receives an ultrasonic signal. The probe
is coupled to the surface with a coupling paste so that the
sound waves from the probe are directed into the test object.
The part of the sound pulse transmitted though the couplet,
generates a small electrical signal which causes a vertical
deflection of the beam spot. This is known as the back wall
echo. If a discontinuity is present, another pulse is detected
between the initial echo and the back wall echo.[6]
Fig 1 Ultrasonic testing probe [4]

__________________________________________________________________________________________
Fig 2 Straight beam probe [4]
Fig 3 Flaw echo [4]
3. SETUP
Equipment parameters:
 Model Name: Einstein II- TFT
 Manufacturer: MODSONIC
 Couplant:
 Zero : 2967
 Range: 50 mm
 Velocity : 5920 m/s
 Delay: 0 mm
 Gain: 27 dB
The study was carried on standard specimen. The material
properties are as follows:
Material: Mild Steel
Thickness: 6mm
Weld Length: 100mm
Edge Preparation: Single V Groove
Weld Joint: Butt Joint
The welding joints where prepared using above specimen
using Manual metal arc welding and Gas metal arc welding.
These joints where prepared using different values of current
and voltage.
Table 1: Current settings in stick welding
Voltage (V) Current (A) Description
400 125 High Current
440 75 Optimal
425 175 High Voltage
Table 2: Voltage settings in mig welding
4. RESULT
The defect size as well as the number is least in the middle
portion[11]. In Manual Metal Arc Welding, the flaws are
obtained nearer to the surface as compared to gas metal arc
welding which indicates that penetration is more in MIG
Welding. Maximum defects are observed at the start. This can
be due to the arc blowing effect wherein the arc is not stable.
High current results in more spatter. High Voltage results in
sticking of the arc to the base metal. Maximum defects are
generally observed at the end. Also when current s high
sputtering on the surface also increases.[7]
Fig 4 Mig high current
Voltage(V) Current (A) Description
31 50 Normal
25 30 Low Voltage
69 20 High Voltage

__________________________________________________________________________________________
Fig 5 Stick normal current
4.1 Manual Metal Arc Welding:
4.1.1 Normal Current:
Fig 6 Ultrasonic pattern at start
The defect is present at a depth of 2mm. The amplitude of the
echo is the highest at the start. This implies that the size of the
defect is maximum
Fig 7 Ultrasonic pattern at middle
At the middle, the defect is detected at a depth of 5mm. The
amplitude of the echo is lesser.
Fig 8 Ultrasonic pattern at end
The discontinuity is detected at 5 mm. The size of the
discontinuity is smaller than that obtained in the beginning.
4.1.2 High Current:
The defect is detected at a depth of 2mm.
The defect is detected at a depth of 3mm. The size of the
defect is smaller than that obtained at the start.
The flaw is at a depth of 5mm but the echo amplitude suggests
that the size of the discontinuity is significantly higher.
4.1.3 High Voltage:

__________________________________________________________________________________________
that the size of the discontinuity is lower than obtained in
earlier two cases.(Normal and High Current)
that the size of the discontinuity remains almost same.
that the size of the discontinuity has increased significantly.
This can be due to the sticking of the arc.
4.2 Gas Metal Arc Welding (MIG):
4.2.1 Normal Current
The discontinuity is obtained at 5mm. The size of
discontinuity is less than those obtained in Manual Metal Arc
Welding. Gas Metal Arc Welding provides better control and
precision.
The flaw is detected at a depth of 5mm. The amplitude of the
echo is less which implies that the size of discontinuity is less.
Also, this indicates a complete penetration.
Fig17 Ultrasonic pattern at end
The flaw is detected at a depth of 3 mm. The amplitude of the
echo is more which implies that the size of discontinuity is
more.
4.2.2 High Current:
The flaw is detected at a depth of 3 mm. The amplitude of the
echo is less which implies that the size of discontinuity is less.

__________________________________________________________________________________________
The flaw is detected at a depth of 3mm.
that the size of the discontinuity has increased significantly.
CONCLUSIONS
Ultrasonic Testing of 6mm thick mild steel plates welded
using Stick and Gas Metal Arc Welding was done. Different
defects are observed.[8] Maximum defects are observed when
high current and high voltage is used. With high current the
sputtering is also increased. Different materials have different
current-voltage characteristics. Amplitude Reject Level (ARL)
and Disregard Level (DRL) indicate the set levels for
acceptance and rejection of amplitude. Different techniques
for categorization of defects involve use of Neural Networks
and Data Acquisition and filtering techniques. Genetic
Algorithms are being developed. [7]
REFERENCES
[1] Non Destructive Material Testing with Ultrasonics–
Krautkramer.
[2] Non Destructive Testing – Det Norske Veritas (DNV),
March 2012
[3] A Guide for Ultrasonic Testing and Evaluation of flaws
– Ship Structure Committee, USA, 1970
[4] Bredif P., Plu J., Pouligny P. and Poldevin C. Phased-
array method for the us-inspection of French rail
repairs. CP975. Review of Quantitative Non-
destructive Evaluation. Ed by D. O.Thompson and
E.Chimenti. 2008. Vol.27. American Institute of
Physics 978-0-7354-0494-6/08
[5] M. Berke, U. Hoppenkamps: "Testing materials
ultrasonically" Krautkrämer Training System, Level 1
3rd edition (1990)
[6] The ultrasonic wave interaction with porosity defects in
welded rail head E. Jasiūnienė, E. Žukauskas ISSN
1392-2114
[7] WELDING DEFECTS PATTERN RECOGNITION
IN TOFD SIGNALS USING LINEAR CLASSIFIER
IMPLEMENTED BY NEURAL NETWORKS
Elineudo P. de Moura
[8] Silk, M.G., LIDINGTON, B.H., “Defect sizing using
an Ultrasonic Time Delay Approach”, British Journal
of NDT, pp. 33-36, March, 1975
[9] Defects Clustering using Kohonen Networks during
Ultrasonic Inspection Thouraya Merazi Meksen, Bachir
Boudraa, Malika Boudraa
[10] Non Destructive Testing Handbook. American Society
for Nondestructive Testing, USA, 1986.
[11] T. Stepinski, F. Lingvall, Automated Defect
Characterization in Ultrasonic NDT, 15th WCNDT,
Roma, 2000

Ultra sonic testing of weldjoints prepared at different voltage and current

More Related Content

What's hot (20)

Similar to Ultra sonic testing of weldjoints prepared at different voltage and current (20)

More from eSAT Journals (20)

Recently uploaded (20)

Ultra sonic testing of weldjoints prepared at different voltage and current