Unit4_IO_13623_AnilRawat.ppt

Input/Output Organization 1
Overview
 Peripheral Devices
 Input-Output Interface
 Asynchronous Data Transfer
 Modes of Transfer
 Priority Interrupt
 Direct Memory Access
 Input-Output Processor
 Serial Communication

POLL 1
• Which of the following is a Peripheral device
A) All input devices
B) All output devices
C) Both A and B
D) None of the above

Input Output Organization
– I/O Subsystem
• Provides an efficient mode of communication between the
central system and the outside environment
– Programs and data must be entered into computer memory for
processing and results obtained from computer must be
recorded and displayed to user.
– When input transferred via slow keyboard processor will be idle
most of the time waiting for information to arrive
– Magnetic tapes, disks

Peripheral Devices
• Devices that are under direct control of computer are said to be
connected on-line.
• Input or output devices attached to the computer are also called
peripherals.
• There are three types of peripherals :
• Input peripherals
• Output peripherals
• Input-output peripherals
Peripheral (or I/O Device)
Monitor (Visual Output Device) : CRT, LCD
KeyBoard (Input Device) : light pen, mouse, touch screen, joy stick, digitizer
Printer (Hard Copy Device) : Daisy wheel, dot matrix and laser printer
Storage Device : Magnetic tape, magnetic disk, optical disk

Poll 2
• Which of the following is a Peripheral device
• A) Touch screen
• B) CRT
• C) LCD
• D) All of the above

Peripheral Devices
Input Devices
• Keyboard
• Optical input devices
- Card Reader
- Paper Tape Reader
- Bar code reader
- Optical Mark Reader
• Magnetic Input Devices
- Magnetic Stripe Reader
• Screen Input Devices
- Touch Screen
- Light Pen
- Mouse
•
Output Devices
• Card Puncher, Paper Tape Puncher
• CRT
• Printer (Daisy Wheel, Dot Matrix, Laser)
• Plotter

POLL 3
• Card puncher is a
• A) Input device
• B) Output device
• C) both A and B
• D) none of the above

Input Output Organization
ASCII (American Standard Code for Information Interchange)
• I/O communications usually involves transfer of alphanumeric
information from the device and the computer.
• Standard binary code for alphanumeric character is ASCII
• ASCII Code :
• It uses 7 bits to code 128 characters (94 printable and 34 non printing)
• 7 bit - 00 - 7F ( 0 - 127 )
• ASCII is 7 bits but most computers manipulate 8 bit quantity as a
single unit called byte.
80 - FF ( 128 - 255 ) : Greek, Italic type font
•Three types of control characters: Format effectors, Information
separators and communication control

Poll 4
• ASCII Stands for
• A) American Standard Code for Information
Interchange
• B) American Stable Code for Information
Interchange
• C) American Standard Communication for
Information Interchange
• American Standard Code for Information
Interlink

• Format Effectors: control the layout of
printing. They include familiar typewriter
controls, such as backspace (BS), horizontal
tabulation(HT), carriage return(CR).
• Information separators: used to separate data
into divisions like paragraphs and pages. They
include characters such as record separator
(RS) and file separator(FS).

• Communication Control characters: these are
useful during the transmission of text
between remote terminals. These include
STX(Start of text) and ETX(end of text)

I/O Interface
• Provides a method for transferring information between internal
storage (such as memory and CPU registers) and external I/O
devices
• Resolves the differences between the computer and peripheral
devices
(1). Peripherals – Electromechanical or Electromagnetic Devices
CPU or Memory - Electronic Device
– Conversion of signal values required
(2). Data Transfer Rate
• Peripherals - Usually slower
• CPU or Memory - Usually faster than peripherals
– Some kinds of Synchronization mechanism may be needed
(3). Data formats or Unit of Information
• Peripherals – Byte, Block, …
• CPU or Memory – Word
(4). Operating modes of peripherals may differ
• must be controlled so that not to disturbed other peripherals connected to CPU

I/O Bus and Interface
Interface :
- Decodes the device address (device code)
- Decodes the commands (operation)
- Provides signals for the peripheral controller
- Synchronizes the data flow and supervises
the transfer rate between peripheral and CPU or Memory
Processor
Interface
Keyboard
and
display
terminal
Magnetic
tape
Printer
Interface Interface Interface
Data
Address
Control
Magnetic
disk
I/O bus
4 types of command interface can receive : control, status, data o/p and data i/p

POLL
• Which of the following is Correct about I/O
interface
• A) Device address
• B) peripheral controller
• C) both A and B
• D none of the above

I/O Bus and Interface
•Control command : is issued to activate peripheral and to inform what to do
•Status command : used to test various status condition in the interface and
the peripherals
•data o/p command : causes the interface to respond by transferring data from
the bus into one of its registers
•data i/p command : interface receives an item of data from the peripheral and
places it in its buffer register.

POLL
• Which of the following is a example of I/O
command
• A) Control
• B) Status
• C) Data
• D) All of the above

I/O Bus and Memory Bus
• MEMORY BUS is for information transfers between CPU and the MM
• I/O BUS is for information transfers between CPUand I/O devices through
their I/O interface
•3 ways to bus can communicate with memory and I/O :
(1). use two separate buses, one to communicate with memory and the
other with I/O interfaces
- Computer has independent set of data, address and control bus one for
accessing memory and another I/O.
- done in computers that have separate IOP other than CPU.
(2). Use one common bus for memory and I/O but separate control lines
for each
(3). Use one common bus for memory and I/O with common control
lines for both
Functions of Buses

Isolated I/O –
Then we have Isolated I/O in which we Have common bus(data and address)
for I/O and memory but separate read and write control lines for I/O. So when
CPU decode instruction then if data is for I/O then it places the address on the
address line and set I/O read or write control line on due to which data transfer
occurs between CPU and I/O. As the address space of memory and I/O is
isolated and the name is so. The address for I/O here is called ports. Here we
have different read-write instruction for both I/O and memory.

Memory Mapped I/O –
In this case every bus in common due to which the same set of instructions
work for memory and I/O. Hence we manipulate I/O same as memory and
both have same address space, due to which addressing capability of memory
become less because some part is occupied by the I/O.

Isolated I/O Memory Mapped I/O
Memory and I/O have seperate
address space
Both have same address space
All address can be used by the
memory
Due to addition of I/O addressable
memory become less for memory
Separate instruction control read and
write operation in I/O and Memory
Same instructions can control both I/O
and Memory
In this I/O address are called ports. Normal memory address are for both
More efficient due to seperate buses Lesser efficient
Larger in size due to more buses Smaller in size
It is complex due to separate separate
logic is used to control both.
Simpler logic is used as I/O is also
treated as memory only.
Differences between memory mapped I/O and isolated I/O –

I/O Interface
- Information in each port can be assigned a meaning depending on the mode of operation of the
I/O device→ Port A = Data; Port B = Command;
- CPU initializes(loads) each port by transferring a byte to the Control Register
→ Allows CPU can define the mode of operation of each port
→ Programmable Port: By changing the bits in the control register, it is possible to change the
interface characteristics
CS RS1 RS0 Register selected
0 x x None - data bus in high-impedence
1 0 0 Port A register
1 0 1 Port B register
1 1 0 Control register
1 1 1 Status register
Programmable Interface
Chip select
Register select
Register select
I/O read
I/O write
CS
RS1
RS0
RD
WR
Timing
and
Control
Bus
buffers
Bidirectional
data bus
Port A
register
Port B
register
Control
register
Status
register
I/O data
I/O data
Control
Status
CPU I/O
Device

11-3. Asynchronous Data Transfer
Synchronous Data Transfer: Clock pulses are applied to all registers
within a unit and all data transfer among internal registers occur
simultaneously during the occurrence of a clock pulse.
Two units such as CPU and I/O Interface are designed independently of
each other.
If the registers in the interface share a common clock with CPU
registers, the transfer between the two is said to be synchronous.

11-3. Asynchronous Data Transfer
Asynchronous Data Transfer: Internal timing in each unit (CPU and
Interface) is independent.
Each unit uses its own private clock for internal registers. Asynchronous
data transfer between two independent units requires that control
signals be transmitted between the communicating units to indicate
the time at which data is being transmitted.
One way of achieving this is by means of STROBE(Control signal to
indicate the time at which data is being transmitted) pulse
and other method is HANDSHAKING(Agreement between two
independent units).

Timeout : If the return handshake signal does not respond within a given time period,
the unit assumes that an error has occurred.

– Asynchronous Serial Transfer
• Synchronous transmission :
– The two unit share a common clock frequency
– Bits are transmitted continuously at the rate dictated by the clock
pulses
• Asynchronous transmission :
– Binary information sent only when it is available and line remain
idle otherwise
– Special bits are inserted at both ends of the character code
– Each character consists of three parts :
» 1) start bit : always “0”, indicate the beginning of a character
» 2) character bits : data
» 3) stop bit : always “1”
1 1 1
1 0
0
0
0
Start
bit
Character bits
Stop
bit

• Asynchronous transmission rules :
– When a character is not being sent, the line is kept in the 1-state
–  The initiation of a character transmission is detected from the
start bit, which is always “0”
–  The character bits always follow the start bit
–  After the last bit of the character is transmitted, a stop bit is
detected when the line returns to the 1-state for at least one bit
time
• Baud Rate : Data transfer rate in bits per second
– 10 character per second with 11 bit format = 110 bit per second

Universal Asynchronous Receiver Transmitter
A typical asynchronous communication interface available as an IC
Transmitter Register
- Accepts a data byte(from CPU) through the data bus
- Transferred to a shift register for serial transmission
Receiver Register
- Receives serial information into another shift register
- Complete data byte is sent to the receiver register
Status Register Bits
- Used for I/O flags and for recording errors
Control Register Bits
- Define baud rate, no. of bits in each character, whether to generate and check parity, and no. of
stop bits
Chip select
I/O read
I/O write
CS
RS
RD
WR
Timing
and
Control
Bus
buffers
Bidirectional
data bus
Transmitter
register
Control
register
Status
register
Receiver
register
Shift
register
Transmitter
control
and clock
Receiver
control
and clock
Shift
register
Transmit
data
Transmitter
clock
Receiver
clock
Receive
data
CS RS Oper. Register selected
0 x x None
1 0 WR Transmitter register
1 1 WR Control register
1 0 RD Receiver register
1 1 RD Status register
Internal
Bus

 Binary information received from external device is usually
stored in memory.
 Information transferred from central computer into an external
device originates in the memory unit.
The CPU merely execute I/O instructions and may accept data
temporarily but ultimate source or destination is the Memory Unit.
Data transfer between central computer and I/O devices may be
handled in a variety of modes. Some modes use CPU as
intermediate path and others transfer data directly to and from
memory unit.
Data Transfer to or from peripheral can be handled in one of
three possible modes :
 Programmed I/O
 Interrupt-Initiated I/O
 Direct Memory Access (DMA)
Modes of Transfer

Input/output Organization 33
Modes of Transfer – Programmed I/O

Programmed I/O
- Programmed I/O operations are the result of I/O
Instructions written in computer program.
Each data item transfer is initiated by an instruction in
the program.
- Usually, transfer is to and from a CPU register to
peripheral.
- Other instructions are needed to transfer data to and from CPU
and Memory
- Transferring data under program control requires
constant monitoring of the peripheral by CPU.

• In programmed I/O method, CPU stays in a
program loop until the I/O unit indicated that it is
ready for data transfer.
• This is a time consuming process since it keeps
the processor busy needlessly.
• It can be avoided by using Interrupt facility and
special commands to inform the interface to issue
an interrupt request signal when data are
available for the device.

Priority Interrupts
Priority
- Determines which interrupt is to be served first when two or more requests
are made simultaneously
- Also determines which interrupts are permitted to interrupt the computer while
another is being serviced
- Higher priority interrupts can make requests while servicing a lower priority
interrupt
A priority interrupt is a system that establishes priority over the
various sources to determine
- which condition is to serviced first when two or more requests
arrive simultaneously
-which conditions are permitted to interrupt the computer while
another request is being serviced

Priority Interrupts
Priority Interrupt by Software (Polling)
Polling procedure is used to identify highest priority source by software
means
- common branch address for all the interrupts
- Priority is established by the order of polling the devices(interrupt sources)
- highest priority device is tested first and if interrupt is on , control
branches to service routine for this source otherwise next lower priority
source is tested
- Flexible since it is established by software
- Low cost since it needs a very little hardware
- Very slow
- if there are many interrupt time required to poll may exceed time available to
service IO device

Priority Interrupts
Priority Interrupt by Hardware
- Require a priority interrupt manager which accepts all the interrupt requests
to determine the highest priority request
- Fast since identification of the highest priority interrupt request is identified by
the hardware
- Fast since each interrupt source has its own interrupt vector to access
directly to its own service routine
- Can be addressed using serial or parallel connection of interrupt lines.
Example of serial is Daisy chaining Priority

Hardware Priority Interrupts – Daisy Chain
Device 1
PI PO
Device 2
PI PO
Device 3
PI PO
INT
INTACK
Interrupt request
Interrupt acknowledge
To next
device
CPU
VAD 1 VAD 2 VAD 3
* Serial hardware priority function
* Interrupt Request Line
- Single common line
* Interrupt Acknowledge Line
- Daisy-Chain
-Serial connection of all device that request an interrupt
-Device with highest priority placed in first position followed by devices with lower
priority and so on.
-Interrupt generated by any device  signals low state interrupt line
-CPU responds by enabling interrupt acknowledgement (INTACK) line.
- device receives PI=1 and passes to next only when not requesting else PI=0
-Thus device with PI=1 and PO=0 is one with highest priority requesting interrupt

Example: Daisy chain working

POLL
If PI=1 and PO =0 , then
(a) Interrupt is activated
(b)No Interrupt
(c) Interrupt ACK passed to next device
(d)Invalid Interrupt

Parallel Priority Interrupts
Mask
register
INTACK
from CPU
Priority
encoder
I0
I1
I 2
I 3
0
1
2
3
y
x
IST
IEN
0
1
2
3
0
0
0
0
0
0
Disk
Printer
Reader
Keyboard
Interrupt register
Enable
Interrupt
to CPU
VAD
to CPU
Bus
Buffer
IEN: Set or Clear by instructions ION or IOF
IST: Represents an unmasked interrupt has occurred. INTACK enables tristate Bus Buffer to load VAD generated
by the Priority Logic
Interrupt Register:
- Each bit is associated with an Interrupt Request from different Interrupt Source - different priority level
- Each bit can be cleared by a program instruction
Mask Register:
- Mask Register is associated with Interrupt Register
- Each bit can be set or cleared by an Instruction

Priority Encoder
Determines the highest priority interrupt when more than one
interrupts take place
Priority Encoder Truth table
1 d d d
0 1 d d
0 0 1 d
0 0 0 1
0 0 0 0
I0 I1 I2 I3
0 0 1
0 1 1
1 0 1
1 1 1
d d 0
x y IST
(IST) = I0 + I1 + I2 + I3
Inputs Outputs
Boolean functions

POLL
Which of the following statement is correct
– Parallel Priority interrupt can handle multiple
interrupt request
a. True
b. False

Interrupt Cycle
At the end of each Instruction cycle
- CPU checks IEN and IST
- If IEN  IST = 1, CPU -> Interrupt Cycle
SP  SP - 1 Decrement stack pointer
M[SP]  PC Push PC into stack
INTACK  1 Enable interrupt acknowledge
PC  VAD Transfer vector address to PC
IEN  0 Disable further interrupts
Go To Fetch to execute the first instruction
in the interrupt service routine

Initial and Final Operations
JMP PTR
JMP RDR
JMP KBD
JMP DISK
0
1
2
3
Program to service
magnetic disk
Program to service
line printer
Program to service
character reader
Program to service
keyboard
DISK
PTR
RDR
KBD
255
256
750
256
750
Stack
Main program
current instr.
749
KBD
interrupt
2
VAD=00000011 3
4
Disk
interrupt
5
6
7
8
9 10
11
1
Initial and Final Operations
Each interrupt service routine must have an initial and final set of
operations for controlling the registers in the hardware interrupt system
Initial Sequence
[1] Clear lower level Mask reg. bits
[2] IST <- 0
[3] Save contents of CPU registers
[4] IEN <- 1
[5] Go to Interrupt Service Routine
Final Sequence
[1] IEN <- 0
[2] Restore CPU registers
[3] Clear the bit in the Interrupt Reg
[4] Set lower level Mask reg. bits
[5] Restore return address, IEN <- 1

Direct Memory Access
Data bus
Read
Write
ABUS
DBUS
RD
WR
Bus request
Bus granted
BR
BG
CPU
Data bus
DMA select
Read
Write
Bus request
Bus grant
Interrupt
DS
RS
RD
WR
BR
BG
Interrupt
Data bus
buffers
Address bus
buffers
Address register
Word count register
Control register
DMA request
DMA acknowledge to I/O device
Control
logic
Internal
Bus
Fig 2: Block diagram of DMA controller
* Block of data transfer between high speed devices like Disk and Memory
* DMA controller - Interface which takes over the buses to manage the transfer directly between
Memory and I/O Device, freeing CPU for other tasks
* CPU initializes DMA Controller by sending memory address and the block size (number of words)
Fig 1: CPU bus signals for DMA transfer
Address bus
Address register:
Contains an address to specify
Desired location in memory
Word count register
Holds no. of words to be transferred
Control register
Specifies the mode of transfer

DMA Transfer can be made in several ways
(1) Burst Transfer : a block sequence consisting of memory words is transferred
in continuous burst while the DMA controller is master of memory
bus
- This mode of transfer is needed for fast devices such as magnetic
disk where data transmission cannot be stopped or slowed down
until an entire block is transferred
(2) Cycle stealing : Alternative technique called cycle stealing allows DMA controller to
transfer one data word at time after which it must return control of
the buses to the CPU.
- CPU merely delays its operation for one memory cycle to allow the
direct memory I/O transfer to “steal” one memory cycle
Direct Memory Access
RD and WR is bidirectional
When BG=0 CPU can communicate with DMA Register
When BG=1 CPU left the buses and DMA can communicate directly with memory

DMA I/O Operation
DMA is first initialized by CPU. After that DMA starts and continues to transfer data
between memory and peripheral unit until an entire block is transferred.
CPU initializes the DMA by sending following information through data bus:
(1) Starting address of the memory block (for read/write)
(2) Word Count (no. of words in memory block)
(3) Control to specify mode of transfer (E.g. read/write)
(4) A control to start DMA Transfer

DMA Transfer
BG
BR
CPU
RD WR Addr Data
Interrupt
Random-access
memory unit (RAM)
RD WR Addr Data
BR
BG
RD WR Addr Data
Interrupt
DS
RS DMA
Controller
I/O
Peripheral
device
DMA request
DMA ack.
Read control
Write control
Data bus
Address bus
Address
select

I/O Processor - Channel
Channel
- Processor with direct memory access capability that communicates with I/O devices
- Channel accesses memory by cycle stealing
- Unlike DMA Controller, IOP can fetch and execute its own instruction
- IOP Instructions (Commands) specially designed to facilitate I/O transfer.
- Data gathered in IOP at device rate and bit capacity while CPU executing own program
- Transfer between IOP and Device similar to Programmed I/O and
transfer between IOP and Memory similar to DMA
- CPU is master while IOP is slave processor
- CPU initiates the channel by executing a channel I/O class instruction and once initiated,
channel operates independent of the CPU
PD PD PD PD
Peripheral devices
I/O bus
Input-output
processor
(IOP)
Central
processing
unit (CPU)
Memory
unit
Memory
Bus

Channel CPU Communication
Send instruction
to test IOP.path
If status OK, then send
start I/O instruction
to IOP.
CPU continues with
another program
Transfer status word
to memory
Access memory
for IOP program
Conduct I/O transfers
using DMA;
Prepare status report.
I/O transfer completed;
Interrupt CPU
Request IOP status
Transfer status word
to memory location
Check status word
for correct transfer.
Continue
CPU operations IOP operations

Unit4_IO_13623_AnilRawat.ppt

More Related Content

What's hot (20)

Similar to Unit4_IO_13623_AnilRawat.ppt (20)

Recently uploaded (20)

Unit4_IO_13623_AnilRawat.ppt