IRJET- IoT based Flow Analyzing and Alerting System
0 likes27 views
This document describes an IoT-based system for continuously measuring and analyzing water flow from a dam. The system uses flow sensors placed at multiple points along a river to measure flow rate, velocity, time taken, and distance covered. A Raspberry Pi processes the sensor data and stores it on the cloud. If the flow exceeds a threshold, an alert is sent. The system provides real-time water flow data and analysis in a tabular format to help monitor for flooding. It is a low-cost, efficient method for continuous water flow measurement and alerting.
![International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 06 Issue: 04 | Apr 2019 www.irjet.net p-ISSN: 2395-0072
© 2019, IRJET | Impact Factor value: 7.211 | ISO 9001:2008 Certified Journal | Page 3038
Iot Based Flow Analyzing and Alerting System
Gautami Keskar1, Akanksha Kolte2, Ajinkya Jadhav3, Anant More4
1,2,3Dept. of E&TC Engineering, RMD Sinhgad School of Engineering, Maharashtra, India
4Anant More, Prof. Dept. of E&TC Engineering, RMD Sinhgad School of Engineering, Maharashtra, India
---------------------------------------------------------------------***----------------------------------------------------------------------
Abstract - The continuous measurement of flow of water
released from dam for long period of time is crucial in water
resource studies. However the accurate estimation of flow is
difficult. Thus a robust and efficientmethodof measurementis
required. In this study an innovativesystem, theflowanalyzing
and alerting system used for continuous measurement of
water flow. This system uses flow sensortomeasuretheflow of
water and time taken by water to reach a certain destination
also measures total distance. The system will storethedataon
cloud so that it can be accessible from anywhere. Thesystemis
reliable and easily accessible. This system will measure the
mass flow and analyze the flow.
Key Words: Measurement of flow, Analyzing and
alerting system, Flow sensor, Distance and time
measured.
1. INTRODUCTION
Dam water discharge is an important hydrological factor in
dam for management and control of water resource.
However it is very difficult to measure average velocity,
distance covered by waterandtime requiredtoreachcertain
destination in unsteady flows or during extreme
hydrological events such as flooding therefore establishing
the method and technology for water flow analysis is a
crucial issue.
For continuous measurement of water, the system
contain number of nodes placed at different points. In river
each node have flow sensors which will measure flow with
respect to river bed. All nodes will operate in real time and
central station can access data from any node and give the
average result. The data will be in tabular format having
parameters such as flow rate, velocity, time taken, distance
covered etc. All the data will be stored on cloud, so that user
can access data from anywhere, if the flow exceeds system
will send an alert to user via mail system.
In this paper section 2 discusses about literature survey
on flow analyzing and alerting while section 3 discusses on
Internet of things. Section 4 discusses implementation of
flow analyzing and alerting system, and results obtained
through the system are discussed in section 5.Section 6
concludes paper.
1.1 Literature Survey
In many cases, river discharge is indirectly estimated from
water level or stream flow velocity near water surface.
However these methods have limited applicability. In this
study, an innovative system, The Fluid Acoustics
Tomography System(FATS), was used for continuous
discharge measurement. Operatinginunsteadystreamflow,
“ NEW ACOUSTIC SYSTEM “ was developed by graduate
school of engineering, hiroshima university, kagamiyama,
higashi-hiroshima 739-8527, japan[1]
The use of acoustic Doppler current profilers(ADCPs) from
moving boat is now a commonly used method formeasuring
stream flow. In 2013”Measuring Discharge With Acoustic
Doppler Current Profiler from A Moving Boat”: U.S
Geological Survey Technique and methods 3A-22, 72p[2]
In “Continuous Measurement of Flow Rate in a Shallow
Gravel Bed River By NewAcousticSystem”published24May
2012, FATs covers the entire cross section of river in single
measurement. The flow rates measured by FATs were
compared to those estimated by moving boat ADCPs and
rating curve (RC) methods [3].
1.2 Internet of Things
Internet of things (IOT) is defined as network of physical
object/things- devices, vehicles, buildings embedded with
sensors, microcontroller and network connectivity that
enables these objects to collect and exchange data. Each
device has a unique identification and must be able to
capture real-time data autonomously.IOTsystemconsistsof
sensors, processors, gateways,andapplications.Itallowsthe
device to be connected to the internet and to each other.The
cloud services collect, store andanalyzethedata collected by
the sensor and allow people to take decisions accordingly
2. Implementation
This system makes use of one sensor (flow) for each node
and processing module raspberry pi. Therefore sensor
captures data in form of analog signal. These signalsaresent
to raspberry pi module](https://image.slidesharecdn.com/irjet-v6i4650-190706100207/85/IRJET-IoT-based-Flow-Analyzing-and-Alerting-System-1-320.jpg)
![International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 06 Issue: 04 | Apr 2019 www.irjet.net p-ISSN: 2395-0072
© 2019, IRJET | Impact Factor value: 7.211 | ISO 9001:2008 Certified Journal | Page 3039
Figure 1: Circuit diagram for flow analyzing system
The Raspberry pi will process digital information analyze it
and then further communication is done. The data is stored
on cloud and alert is sent if flow increases. The code is
written in python and raspberry pi version 3 is used to
simulate the code.
The flow analyzing system shown in fig 2 employs sensor
to collect data (parameter flow rate). This data is processed
through the Raspberrypimicrocontrollermoduleandstored
on cloud. This data can be accessed by users. The data is
collected, processed, analyzed and displayed all in real time.
Python is an interpreted high level programming language
for general purpose programming. Created
By guido van rossum and first released in1991.Pythonhasa
design philosophy that emphasizes code reliability, notably
using significant whitespace. It provides constructs that
enable clear programming on both small and large scales.
Figure2: Block diagram for flow analyzing system.
Flow sensor is device used to measure volume o mass of gas
or liquid. Flow measurement is quantification of bulk fluid
movement. Flow may be measured by measuring velocity of
fluid over known area. For very large flows, tracer methods
may be used to deduce the flow rate.
The result will be displayed and saved in tabular format on
phpMyAdmin as shown below;
Figure 3: Result in Tabular Format
3. CONCLUSIONS
The low cost, efficient, real-time water flow analyzing and
alerting system has been implemented and tested. Through
this system the officials can keep track of flow rate of water
released and send immediate warnings to public. This can
prevent flood situations. Quick actions can be taken to
prevent losses occurring due to flood. The system can be
easily installed, with base station kept close to dam and task
of monitoring can be done.
Internet of things and its services are becoming part of our
everyday life, ways of working and business. There is great
deal of research on developing crucial building blocks and
models for the next generationinternetservicesupportedby
a plethora of connected things.
ACKNOWLEDGEMENT
The authors are thankful to project guide prof. Anant More,
and prof. Snehal Bhosale, head of E&TC dept., RMD sinhgad
school of engineering, SPPU university Pune, India for
providing necessary resourcesandinfrastructuretoconduct
the project work and foe this encouragement.
REFERENCES
[1]Kiyosi Kawanisi, Arata Kaneka, Shinya Nigo, Mohammad
Soltaniasl, Mahmoud f.Maghrebi.
“ NEW ACOUSTIC SYSTEM” Graduate school of engineering,
Hiroshima university, Japan.
[2] Mueller, D.S Wagner, C.R Rehmel, M.S Oberg, K.A
Rainville, 2013 ”MEASURING DISCHARGE FROM ACOUSTIC
DOPPLER CURRENT PROFILERFROMAMOVINGBOAT”:U.S
Geological survey techniques and methods.
[3] K. kawanisi, M. Razaz, K. Ishikawa, J. Yano, and
M.Soltaniasl“CONTINUOS MEASUREMENT OF FLOW RATE
IN SHALLOW GRAVEL BED RIVER BY A NEW ACOUSTIC
SYSTEM”: published 24 May 2012.](https://image.slidesharecdn.com/irjet-v6i4650-190706100207/85/IRJET-IoT-based-Flow-Analyzing-and-Alerting-System-2-320.jpg)
IRJET- IoT based Flow Analyzing and Alerting System
- 1. International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056 Volume: 06 Issue: 04 | Apr 2019 www.irjet.net p-ISSN: 2395-0072 © 2019, IRJET | Impact Factor value: 7.211 | ISO 9001:2008 Certified Journal | Page 3038 Iot Based Flow Analyzing and Alerting System Gautami Keskar1, Akanksha Kolte2, Ajinkya Jadhav3, Anant More4 1,2,3Dept. of E&TC Engineering, RMD Sinhgad School of Engineering, Maharashtra, India 4Anant More, Prof. Dept. of E&TC Engineering, RMD Sinhgad School of Engineering, Maharashtra, India ---------------------------------------------------------------------***---------------------------------------------------------------------- Abstract - The continuous measurement of flow of water released from dam for long period of time is crucial in water resource studies. However the accurate estimation of flow is difficult. Thus a robust and efficientmethodof measurementis required. In this study an innovativesystem, theflowanalyzing and alerting system used for continuous measurement of water flow. This system uses flow sensortomeasuretheflow of water and time taken by water to reach a certain destination also measures total distance. The system will storethedataon cloud so that it can be accessible from anywhere. Thesystemis reliable and easily accessible. This system will measure the mass flow and analyze the flow. Key Words: Measurement of flow, Analyzing and alerting system, Flow sensor, Distance and time measured. 1. INTRODUCTION Dam water discharge is an important hydrological factor in dam for management and control of water resource. However it is very difficult to measure average velocity, distance covered by waterandtime requiredtoreachcertain destination in unsteady flows or during extreme hydrological events such as flooding therefore establishing the method and technology for water flow analysis is a crucial issue. For continuous measurement of water, the system contain number of nodes placed at different points. In river each node have flow sensors which will measure flow with respect to river bed. All nodes will operate in real time and central station can access data from any node and give the average result. The data will be in tabular format having parameters such as flow rate, velocity, time taken, distance covered etc. All the data will be stored on cloud, so that user can access data from anywhere, if the flow exceeds system will send an alert to user via mail system. In this paper section 2 discusses about literature survey on flow analyzing and alerting while section 3 discusses on Internet of things. Section 4 discusses implementation of flow analyzing and alerting system, and results obtained through the system are discussed in section 5.Section 6 concludes paper. 1.1 Literature Survey In many cases, river discharge is indirectly estimated from water level or stream flow velocity near water surface. However these methods have limited applicability. In this study, an innovative system, The Fluid Acoustics Tomography System(FATS), was used for continuous discharge measurement. Operatinginunsteadystreamflow, “ NEW ACOUSTIC SYSTEM “ was developed by graduate school of engineering, hiroshima university, kagamiyama, higashi-hiroshima 739-8527, japan[1] The use of acoustic Doppler current profilers(ADCPs) from moving boat is now a commonly used method formeasuring stream flow. In 2013”Measuring Discharge With Acoustic Doppler Current Profiler from A Moving Boat”: U.S Geological Survey Technique and methods 3A-22, 72p[2] In “Continuous Measurement of Flow Rate in a Shallow Gravel Bed River By NewAcousticSystem”published24May 2012, FATs covers the entire cross section of river in single measurement. The flow rates measured by FATs were compared to those estimated by moving boat ADCPs and rating curve (RC) methods [3]. 1.2 Internet of Things Internet of things (IOT) is defined as network of physical object/things- devices, vehicles, buildings embedded with sensors, microcontroller and network connectivity that enables these objects to collect and exchange data. Each device has a unique identification and must be able to capture real-time data autonomously.IOTsystemconsistsof sensors, processors, gateways,andapplications.Itallowsthe device to be connected to the internet and to each other.The cloud services collect, store andanalyzethedata collected by the sensor and allow people to take decisions accordingly 2. Implementation This system makes use of one sensor (flow) for each node and processing module raspberry pi. Therefore sensor captures data in form of analog signal. These signalsaresent to raspberry pi module
- 2. International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056 Volume: 06 Issue: 04 | Apr 2019 www.irjet.net p-ISSN: 2395-0072 © 2019, IRJET | Impact Factor value: 7.211 | ISO 9001:2008 Certified Journal | Page 3039 Figure 1: Circuit diagram for flow analyzing system The Raspberry pi will process digital information analyze it and then further communication is done. The data is stored on cloud and alert is sent if flow increases. The code is written in python and raspberry pi version 3 is used to simulate the code. The flow analyzing system shown in fig 2 employs sensor to collect data (parameter flow rate). This data is processed through the Raspberrypimicrocontrollermoduleandstored on cloud. This data can be accessed by users. The data is collected, processed, analyzed and displayed all in real time. Python is an interpreted high level programming language for general purpose programming. Created By guido van rossum and first released in1991.Pythonhasa design philosophy that emphasizes code reliability, notably using significant whitespace. It provides constructs that enable clear programming on both small and large scales. Figure2: Block diagram for flow analyzing system. Flow sensor is device used to measure volume o mass of gas or liquid. Flow measurement is quantification of bulk fluid movement. Flow may be measured by measuring velocity of fluid over known area. For very large flows, tracer methods may be used to deduce the flow rate. The result will be displayed and saved in tabular format on phpMyAdmin as shown below; Figure 3: Result in Tabular Format 3. CONCLUSIONS The low cost, efficient, real-time water flow analyzing and alerting system has been implemented and tested. Through this system the officials can keep track of flow rate of water released and send immediate warnings to public. This can prevent flood situations. Quick actions can be taken to prevent losses occurring due to flood. The system can be easily installed, with base station kept close to dam and task of monitoring can be done. Internet of things and its services are becoming part of our everyday life, ways of working and business. There is great deal of research on developing crucial building blocks and models for the next generationinternetservicesupportedby a plethora of connected things. ACKNOWLEDGEMENT The authors are thankful to project guide prof. Anant More, and prof. Snehal Bhosale, head of E&TC dept., RMD sinhgad school of engineering, SPPU university Pune, India for providing necessary resourcesandinfrastructuretoconduct the project work and foe this encouragement. REFERENCES [1]Kiyosi Kawanisi, Arata Kaneka, Shinya Nigo, Mohammad Soltaniasl, Mahmoud f.Maghrebi. “ NEW ACOUSTIC SYSTEM” Graduate school of engineering, Hiroshima university, Japan. [2] Mueller, D.S Wagner, C.R Rehmel, M.S Oberg, K.A Rainville, 2013 ”MEASURING DISCHARGE FROM ACOUSTIC DOPPLER CURRENT PROFILERFROMAMOVINGBOAT”:U.S Geological survey techniques and methods. [3] K. kawanisi, M. Razaz, K. Ishikawa, J. Yano, and M.Soltaniasl“CONTINUOS MEASUREMENT OF FLOW RATE IN SHALLOW GRAVEL BED RIVER BY A NEW ACOUSTIC SYSTEM”: published 24 May 2012.