The 8086 Micro Processor Architecture By Dr. RidhaJemal

Page: 1Dr. Ridha Jemal
Chapter 2 : The 8086 Processor Architecture
2.1. Introduction to Microprocessor Architecture
2.2. Elements of the 8086 Processor Architecture
2.3. Processor Model
2.4. Programming Model
2.5. Register and Flags
2.6. Memory Addressing Modes
By Dr. Ridha Jemal
Electrical Engineering Department
College of Engineering
King Saud University
1431-1432
EE353: Chapter 2 The8086 Processor Architecture

A computer whose entire CPU is contained on one integrated circuits.
The important characteristics of a microprocessor are the widths of its
internal and external address bus and data bus (and instruction), its clock
rate and its instruction set.
CPU : The part of a computer which controls all the other parts. The CPU
fetches instructions from memory, decodes and executes them. This may
cause it to transfer data to or from memory or to activate peripherals to
perform input or output.
Microprocessor:
The connections between the CPU and memory input/output which
carry the address from/to which the CPU wishes to read or write. The
number of bits of address bus determines the maximum size of memory
which the processor can access.
Address Bus:
Introduction to Microprocessor Architecture

One of a small number of high-speed memory locations in a
computer's CPU.
Register:
A data storage device for which the order of access to different
locations does not affect the speed of access. The term "RAM" has
gained the additional meaning of read-write. Most kinds of
semiconductor read-only memory (ROM) are actually "random access"
in the above sense but are never referred to as RAM. Furthermore,
memory referred to as RAM can usually be read and written equally
quickly (approximately), in contrast to the various kinds of
programmable read-only memory. Finally, RAM is usually volatile
Random Access Memory (RAM):

Storage of Data Structure
For multiple-byte data items stored in memory, need to specify which
order:
(a) Most Significant 8 bits at lowest address ("Big Endian"), OR
(b) Least Significant 8 bits at lowest address ("Little Endian")
Little Endian: 80x86
Big Endian: mc680x0, SPARC, HP Precision (Vipers)
Difference in "endian-ness" can be a problem when transferring data
between machines
Big Endian and Little Endian :

Composition of CPU
REGISTERS
Instruction Pointer Counter : Holds address of instruction being
executed
Instruction Register: Holds instruction while it's decoded/executed
Stack Pointer: Address of top of stack
Accumulator: Result of ALU operations
General-Purpose Registers : Hold temporary results or addresses
during execution of instructions Write results to memory
CONTROL UNIT
Generates control/timing signals
Controls decoding/execution of instructions
ALU
Used during execution of instructions
Mathematical operations: * / + - etc.
Logical operations: shift, rotate

Composition of CPU

Instruction Execution
performs Fetch/Decode/Execute cycle
• Fetch instruction from primary memory
• Increment Program Counter
• Decode
• Fetch operands from memory
• Execute instruction
• Write results to memory
Fetch Time depends on
• Access time of primary memory
• Activity on System Bus
Decode/Execute Time taken depends on
• System Clock speed (frequency)
• Type of instruction

Element of the 8086Microprocessor Architecture
The 80x86 has:
• 16-bit internal data bus
• 20-bit address bus
• Control bus
• Execution Unit
• Bus Interface Unit
Among the on-chip peripherals are:
• 2 direct memory access controllers (DMA)
• Three 16-bit programmable timers
• Clock generator
• Chip select unit
• Programmable Control Registers

The 8086 Processor Model
BIUEU
Block Diagram Architecture
The simplified block diagram of the 80x86 processor model is organized
as two separate processors :
Bus Interface Unit (BIU)
Execution Unit (EU).

The BIU provides hardware functions. Including generation of the memory and
I/0 addresses for the transfer of data between itself and the outside world.
The EU receives program instruction codes and data from the BIU, executes
these in-structions, and stores the results in the general registers. By passing
the data back to the BIU, data can also be stored in a memory location or
written to an output device.
• The main linkage between the two functional blocks is the instruction
queue, with the BIU looking ahead of the current instruction being executed in
order to keep the queue filled with instructions for the EU to decode and
operate on.
• The EU has no connection to the system buses. It receives and outputs all of its
data through the BIU. The execution unit, or EU, handles the arithmetic and
logical operations on the data and has a 6-byte first-in, first-out (FIFO)
instruction queue

The organization of the processor into a separate BIU and EU allows the fetch and
execute cycles to overlap. To see this, consider what happens when the 8086 is
first started. in Figure 3.2.
The Fetch and Execute Cycle
1. The BIU outputs the contents of the instruction pointer register (IP) onto the
address bus, causing the selected byte or word in memory to be read into the BIU.
2. Register IP is incremented by one to prepare for the next instruction fetch.
3. Once inside the BIU, the instruction is passed to the queue: a first-in/first-out
storage register sometimes likened to a pipeline.
4. Assuming that the queue is initially empty, the EU immediately draws this
instruction from the queue and begins execution.
5. While the EU is executing this instruction, the BIU proceeds to fetch a new
instruction. Depending on the execution time of the first instruction, the BIU may
fill the queue with several new instructions before the EU is ready to draw its next
instruction.
6. The cycle continues, with the BIU filling the queue with instructions and the EU
fetching and executing these instructions.

The Fetch and Execute Cycle (contd.)
The BIU is programmed to fetch a new instruction whenever the queue has room
for two additional bytes. The advantage to this pipelined architecture is that the
EU can execute instructions (almost) continually instead of having to wait for the
BIU to fetch a new in-struction. This is shown schematically in the following
Figure.

The “Wait” mode
There are three conditions that will cause the EU to enter a "wait" mode.
• When an instruction requires access to a memory location. The BIU must
suspend fetching instructions and output the address of this memory
location. After waiting for the memory access, the EU can resume executing
instruction codes from the queue, and the BIU can resume filling the queue.
• When the instruction to be executed is a jump instruction. In this case,
control is to be transferred to a new address. The EU must wait while the
instruction at the jump address is fetched. Any bytes presently in the queue
must be discarded (they are overwritten).
• During the execution of slow-executing instructions.

1978: The 8086 was one of the earliest 16-bit processors.
The 80286 is also a 16-bit microprocessor
Motorola 68000 is also a 16-bit microprocessor
Mid 1980’s : 32-bit microprocessors
Intel 80386, 80486 , Motorola 68030
Microprocessors Timeline:
1997: The Pentium II is superscalar, supports multiprocessing, and includes
special instructions for multimedia applications.
2002:The Pentium 4 runs at insane clock rates (3.06 GHz), implements
extended multimedia instructions and has a large on-chip cache.
Internal Architecture may be different from size of Data Bus
Intel 8088: internally 16-bit, 8-bit data bus
Intel 386sx: internally 32-bit, 16-bit data bus
Can build computer using cheaper external parts (eg. I/O interfaces)

Instruction Set: operations, addressing modes
Registers: size, number
Address bus : size (number of bits)
Data bus: size
Control bus: functions
Permissible clock speeds
Microprocessors Difference:
What About the 8088?
The only significant difference between the 8088 microprocessor and the
8086 microprocessor is the BIU. In the 8088, the BIU data bus path is 8 bits
wide Where the 8086 BIU data bus is l6-bit. Another difference is that the
8088 instruction queue is four bytes long instead of six.
In practice, however, the 8088 is found to only be about 30 percent slower
than an 8086.

The 8086 Programming Model
The programming model for a microprocessor shows the various internal
registers that are accessible to the programmer. The Following Figure is a
model for the 8086. In general, each register has a special function.

Page: 17Dr. Ridha Jemal EE353: Chapter 2 The8086 Processor Architecture
The eight, 16-bit general purpose registers are used for arithmetic and logical
operations.
Data Registers
Examples
MOV AL,6D -- Place the immediate hexadecimal value 6D into register AL
MOV DH,25 -- Place the immediate hexadecimal value 25 into register DH
MUL DH -- Multiply AL by DH and store the result into AX.
The four data registers labeled AX, BX, CX and DX may be further subdivided for
8-bit operations into a high-byte or low-byte register, depending where the byte is
to be stored in the register. Thus, for byte operations, the registers may be
individually addressed. So, each of these is 16 bits wide but can be accessed as a
byte or a word.
AX : known as an accumulator is used in arithmetic and logical operations
BX : refers to refers to the 16-bit base register
CX : is used as a counter
DX : may

Example
If SI=1000h, What is the content of AH after the execution of the instruction:
The registers in this group are all 16 bits wide and, unlike the data registers, cannot
be accessed as a low or high byte. These registers are used as memory pointers
Pointers and Index Registers
For example, the instruction MOV AH,[SI] has the word interpretation "Move the
byte whose address is contained in register SI to register AH." SI is thus
inter-preted as "pointing" to the desired memory location. The brackets around SI
are used to indicate the contents of memory pointed to by SI and not the value of
SI itself.
MOV AH,[SI]
AH will store 26H
1000H
1001H
1002H
1003H
26
A4
C5
BD

The following Figure shows the bit definitions for the 16-bit flag register.
• Six of the flags are status indicators reflecting properties of the result of the last
arithmetic or logical instruction
• 8086 flag word. DF, IF, and TF can be set or reset to control the operation of
the processor
• The remaining flags are status indicators. Bits marked X are undefined.
;7FH + 1 = 80H
;there is no carry out of bit 7
;S0H has an odd number of logic ones
;there is a carry out of bit 3 into bit 4
;the result is not 0
;bit seven is 1
;the sign bit has changed
AL=80H
CF=0
PF=0
AF=l
ZF=0
SF=l
OF=l
Example

Bit
Position
Name Function
0 CF
Carry flag: Set on high-order bit carry or borrow; cleared otherwise
2 PF
Parity flag: Set if low-order 8 bits of result contain an even number of 1 bits; cleared
otherwise
4 AF
Set on carry from or borrow to the low-order 4 bits of the result; cleared otherwise
6 ZF Zero flag: Set if result is zero; cleared otherwise
7 SF
Sign flag: Set equal to high-order bit of result
(0 is positive, I is negative)
8 TF
Single-step flag: Once set, a single-step interrupt
occurs after the next instruction executes; TF
is cleared by the single-step interrupt
9 IF
Interrupt-enable flag: When set, maskable
interrupts will cause the CPU to transfer control
to an interrupt vector-specified location
10 DF
Direction flag: Causes string instructions to auto-decrement the appropriate index
register when set; clearing DF causes auto-increment
11 OF
Overflow flag: Set if the signed result cannot be expressed within the number of bits
in the destination operand; cleared otherwise
Status and Control Flags

Central Processing Unit:
CS:IP DS:SI OR DS:DI OR DS:BX SS:SP OR SS:BP

Pointers and Index Registers:
In 8086-based System, we can access 220= 1M memory locations at most
µproc
8086
20 bits (A0-A19)
16 bits (D0- D15)
Address Bus
Data Bus
Control Bus
Proc
8086

IP Register:
The Instruction Pointer register (IP)
contains the offset address of the next
sequential instruction to be executed.
Thus, the IP register cannot be directly
modified.
These register descriptions have slowly
been introducing us to a new way of
addressing memory, called:
segment-offset addressing.
The segment register is used to point to
the beginning of any one of the 64K
sixteen-byte boundaries
00000H
FFFFFH
7000H
Segment address
0000H
FFFFH
….
Physical Address
64 K

Physical Address:
Each segment register is 16
bits wide while the address
bus is 20 bits wide. The BIU
takes care of this by
appending four 0s to the low
order bits of the segment
register
The physical Address is calculated as:
Physical Address= 16xSegment + offset
+
=

Physical Address:
Converting the logical address to the physical address

If the segment register CS, DS and SS have values 1000H, 2000H and 3000H
respectively. What will be the 20 bit start and end addresses of the code, data
and stack segments?
Code Segment: 20-bit start address = CS x10h +0000H
= 10000h
20-bit end address = CS x10H +FFFFH
= 1FFFFH
Data Segment : 20-bit start address = DS x10h +0000H
= 20000H
20-bit end address = DS x10H +FFFFH
= 2FFFFH
Stack Segment : 20-bit start address = SS x10h +0000H
= 30000H
20-bit end address = SS x10H +FFFFH
= 3FFFFH
Data Segment and Code Segment can have a complete overlapping. In addition
Stack Segment and Extra Segment can have an overlapping.

Examples
Lower byte of word is stored at lower address
The word ABC2H stored in the memory starting at 20-bit address 50000H
The double word 452ABDFF stored in the memory starting at 20-bit
address 60000H
C2
AB
50000H
50001H BD
FF
45
2A
60000H
60001H
60002H
60003H

Memory Addressing Mode:

The 8086 Micro Processor Architecture By Dr. RidhaJemal

More Related Content

What's hot (20)

Viewers also liked (9)

Similar to The 8086 Micro Processor Architecture By Dr. RidhaJemal (20)

Recently uploaded (20)

The 8086 Micro Processor Architecture By Dr. RidhaJemal