A Low Power Hybrid Partition SRAM based TCAM with a Parity Bit

International Journal of Innovative Research in Advanced Engineering (IJIRAE) ISSN: 2349-2163
Volume 1 Issue 6 (July 2014) http://ijirae.com
_________________________________________________________________________________________________
© 2014, IJIRAE- All Rights Reserved Page - 102
A Low Power Hybrid Partition SRAM based TCAM with a
Parity Bit
Thushara T Hima Sara Jacob
Dept. of ECE, MG University Dept. of ECE, MG University
Mangalam College of Engineering, Kerala Mangalam College of Engineering, Kerala
Abstract— Ternary Content Addressable memory provides high speed search operation. When compared to RAM, TCAM suffers
certain limitation like low bit density, slow access time, high cost per bit. In this paper, we introduced a parity bit to boost the
searching speed HP SRAM based TCAM with less power and delay. A novel memory architecture called HP SRAM based TCAM,
which emulates TCAM functionality with SRAM memory. The architecture of HP SRAM based TCAM with a parity bit was
verified by VHDL in ModelSim.
Keywords— TCAM, APT, BPT, APTAG, Hybrid Partition, SRAM, ANDing operation.
I. INTRODUCTION
Ternary Content Addressable (TCAM) is a special type of memory, which receives an input search word and returns
the address of that word which it is stored on its data bank [1]. TCAM search the entire contents in a single clock cycle.
TCAM has the ability to store three states 0, 1, and don’t care condition (“X”). It can be described as the opposite of
RAM [2]. Due to its parallel nature, TCAM used a wide variety of applications such as network routers, image
processing and data compression.
When compared to RAM, the cost of conventional TCAM device is high [3]. Hybrid Partitioned SRAM based TCAM
achieves advantages like bit density, lower cost, and comparable search performance. HP SRAM based TCAM that
emulates TCAM functionality with SRAM memory [4]. Conventional TCAM divide along vertically and horizontally
and form TCAM sub tables. Each TCAM sub table is named as Hybrid Partition. All TCAM sub tables are stored in their
corresponding SRAM memory units.
In this work, a parity bit is introduced to boost the searching speed of HP SRAM based TCAM with less power and
delay. These newly introduced parity bits are used to find the matched word and reduce the comparison with the
mismatched word. This is similar to the existing HP SRAM based TCAM, but it has a different operating principle. By
this way the total power consumption in HP SRAM based TCAM is reduced when compared with already existing
schemes [5]-[8].
II. ARCHITECTURE OF HP SRAM BASED TCAM
Fig. 1 illustrates an overall architecture of HP SRAM based TCAM where each layer corresponds to Fig. 2. It contains
m layers and Global Priority Encoder (GPE). All layers receive input word simultaneously during searching operation.
Potential Matching Address (PMA) is an output of each layer. If multiple PMA occurs, GPE select the highest priority as
a Matching Address (MA). Lower layer of PMA has the highest priority.
Fig. 1 Memory Architecture of HP SRAM based TCAM

_________________________________________________________________________________________________
Fig. 2 Architecture of a layer of HP SRAM based TCAM
Main components are Bit Position Tables (BPTs), Address Position Tables (APTs), Address Position Table Address
Generators (APTAGs), Local Priority Encoder (LPE), and ANDing operation. In BPT, 2ᵂ bits of memory are grouped
into 2ᵂ‾ᵇ bit of rows. Each row is supplemented with a value is called Last Index (LI) and its length is w+1 bit. The high
order bits (“w-b”) of input words used to select a particular row in BPT acting as an address. This address is termed as
BPT Address (BPTA). The low order bits (“b”) of the input sub word are used to indicate a particular bit position in the
row selected and it’s named as Bit Position Indicator (BPI). If BPI is high means input sub word is present. Last Index of
a row is set to the total number of bits in all previous rows reduced by one. Fig. 3 shows the Conceptual view of BPT.
Fig. 3 Conceptual view of BPT
APTAG generates an address referred to APTA, which contains 1’s counter and adder. The 1’s counter counts the
number of ones in the selected row of BPT and then forwards this information to adder. The adder then adds the 1’s
counter output and LI of the selected row. Fig. 4 shows the conceptual view of APT, where K bits represent the number
of bits in each row.
Fig. 4 Conceptual view of APT

_________________________________________________________________________________________________
A. Searching in HP SRAM based TCAM
During searching operation [10], an input word is applied to all layers of HP SRAM based TCAM and it’s partitioned
into n sub words, which are then applied to their corresponding BPTs in parallel. Upon reading, each access memory
location produces a single bit ie, ‘1’ or ‘0’. If read out a bit is high, an input sub word is present and sustain the search
operation. Upon validation of all sub word, each sub word access a memory location in its corresponding APT and read
K bits data. All the validated sub words read out their respective memory locations concurrently from their corresponding
APT, which are then bit-wise ANDed. LPE receives the K-bit AND operation result and selects PMA. GPE select MA
from the multiple PMA.
B. Searching in HP SRAM based TCAM with a Parity Bit
The new architecture has the same interface as the conventional HP SRAM based TCAM with one extra bit. The
proposed TCAM with a parity bit design consisting of the original data segment and an extra one bit segment derived
from the actual data bits. Parity bit is either odd or even. The extractor is used to find the parity bit value. During the
search operation, the matched parity bit value of word is found first. Only the word whose parity bit value matched will
be compared with the search word and reduce the comparison with the mismatched word [9].
III. RESULTS
A. Simulation Result
The performance analysis HP SRAM based TCAM architecture is analysed and it is simulated using ModelSim
simulator in Fig. 5. Also HP SRAM based TCAM with a parity bit is analysed as shown in Fig. 6.
Fig. 5 Simulated Waveform of HP SRAM based TCAM
Fig. 6 Simulated Waveform of HP SRAM based TCAM with a Parity Bit
B. Synthesis Results
Using Xilinx ISE 13.1, synthesis is done and analysed. The synthesis report is gives the parameters enhanced like
power dissipation and delay.

_________________________________________________________________________________________________
Fig. 7 Delay of HP SRAM based TCAM
Fig. 8 Delay of HP SRAM based TCAM with a Parity Bit
Fig .9 Power of HP SRAM based TCAM

_________________________________________________________________________________________________
Fig. 10 Power of HP SRAM based TCAM with a Parity Bit
C. Results Comparison
TABLE I shows that HP SRAM based TCAM with a parity bit has given the better performance compared to existing
method.
TABLE I
COMPARISON OF HP SRAM BASED TCAM AND HP SRAM BASED TCAM WITH A PARITY BIT
Parameter Delay (ns) Power (mW) Power*Delay (J)
HP SRAM based TCAM 7.219 61 4.49E-10
HP SRAM based TCAM with a Parity Bit 5.684 55 3.12E-10
IV.CONCLUSIONS
We proposed a low power TCAM with high speed. It support large input patterns with much simpler design structure,
and has a deterministic search performance. The proposed design has a low power dissipation and shorter propagation
delay compared to existing method.
ACKNOWLEDGMENT
I would like to take this opportunity to express my sincere gratitude to all my professors who have guided, inspired
and motivated me for my project work. It gives me immense pleasure to acknowledge their co-operation.
REFERENCES
[1] S. Baeg, “Low power ternary content-addressable memory design using a segmented match line, “IEEE Trans. Circuits Syst. I, vol.55, no.6, pp.
1485-1494, Jul.2008.
[2] K. Pagiamtzis and A. Sheikholeslami, “Content-addressable memory (CAM) circuits and architectures: A tutorial and survey,” IEEE J. Solid
State Circuits, vol. 41,n0. 3,pp. 712-727, Mar. 2006.
[3] P. Mahoney, Y. Savaria, G. Bois, and P. Plante, “Performance characterization for the implementation of content addressable memories based
on parallel hashing memories,” P. Stentrom (ED.): Trans. HiPEAC II, LNCS 5470, pp.307-325, 2009.
[4] Zahid Ullah, Kim Ilgon, and Sanghyeon baeg, “Hybrid partitioned SRAM-based ternary content addressable memory,” IEEE Trans. Circuits
Syst. I, vol. 59, no.12, pp. 2969-2978, Dec. 2012.
[5] Anh-Tuan Do, Shoushun Chen, Zhi-Hui Kong, and Kiat Seng Yeo, “A high speed low power CAM with a parity bit and power-gated ML
sensing,” IEEE Trans. Very Large Scale Integration (VLSI) System, vol. 21, no. 1, pp. 151-156, Jan. 2013.
[6] K. Pagiamtzis and A. Sheikholeslami, “A low-power content- addressable memory (CAM) using pipelined hierarchical search scheme,” IEEE J.
Solid-State Circuits, vol. 39, pp. 1512-1519, Sep. 2004.
[7] I. Arsovski and A, Sheikholeslami, “A mismatch-dependent power allocation technique for matchline sensing in content-addressable memories,”
IEEE J. Solid-State Circuits, vol.38, no. 11, pp. 1958-1966, Nov. 2003.
[8] J. Chang, “Using the dynamic power source technique to reduce TCAM leakage power,” IEEE Trans. Circuits Syst. II, vol. 57, no. 11, pp. 888-
892, Nov. 2010.
[9] Do, S. S. Chen, Z. H. Kong, and K. S. Yeo, “A low-power CAM with efficient power and delay trade-off,” in Proc. IEEE int. Symp. Circuits
Syst. (ISCAS), 2011, pp. 2573-2576.
[10] B. D. Yang, Y. K. Lee, S. W. Sung, J. J. Min, J. M. Oh, and H. J. Kang, “A low power content addressable memory using low swing search
lines,” IEEE Trans. Circuits Syst. I, vol.58, no. 12, pp. 2849-2858, Dec. 2011.

A Low Power Hybrid Partition SRAM based TCAM with a Parity Bit

More Related Content

Viewers also liked (9)

Similar to A Low Power Hybrid Partition SRAM based TCAM with a Parity Bit (20)

More from AM Publications (20)

Recently uploaded (20)

A Low Power Hybrid Partition SRAM based TCAM with a Parity Bit