Band-pass Filter with Harmonics Suppression Capability

International Journal of Electrical and Computer Engineering (IJECE)
Vol. 8, No. 4, August 2018, pp. 2512~2520
ISSN: 2088-8708, DOI: 10.11591/ijece.v8i4.pp2512-2520  2512
Journal homepage: http://iaescore.com/journals/index.php/IJECE
Band-pass Filter with Harmonics Suppression Capability
Izni Husna Idris1
, Mohamad Rijal Hamid2
, Kamilia Kamardin3
, Mohamad Kamal A Rahim4
,
Farid Zubir5
, Huda A Majid6
1,2,4,5
Advance RF and Microwave Research Group (ARFMRG), Faculty of Electrical Engineering,
Universiti Teknologi Malaysia, Johor Bahru, Johor, Malaysia
3
Computer Systems Engineering Group, Advanced Informatics School, Universiti Teknologi Malaysia,
Kuala Lumpur, Malaysia
3
Wireless Communication Centre (WCC), Universiti Teknologi Malaysia, Kuala Lumpur, Malaysia
6
Research Center for Applied Electromagnetics, Faculty of Electrical and Electronic Engineering,
Universiti Tun Hussein Onn Malaysia, Batu Pahat, Johor, Malaysia
Article Info ABSTRACT
Article history:
Received Feb 12, 2018
Revised Jun 19, 2018
Accepted Jun 26, 2018
This paper presents a Band-pass Filter (BPF) with a very wide suppressions
band. The filter design is based on a modified U-shaped slot. Two pair of U-
shaped slots is used to ensure that the filter can suppress the unwanted
frequencies up to 4th
harmonics. In order to achieve sharp skirt, two
transmission zeroes are created near the passband area. Additional
transmission zeroes are introduced to deepen the stopband area. Therefore,
the passband range starts from 1.3 to 3.3 GHz and the stopband range from
3.3 GHz up to 9 GHz are achieved. The filter performances are verified
through simulated and measured results.
Keyword:
Band-pass filter
Filter
Harmonic suppression
Slot filter
Copyright © 2018 Institute of Advanced Engineering and Science.
All rights reserved.
Corresponding Author:
Izni Husna Idris,
Advance RF and Microwave Research Group (ARFMRG),
Faculty of Electrical Engineering,
Universiti Teknologi Malaysia,
81310 Johor, Malaysia.
Email: husnaidris89@gmail.com
1. INTRODUCTION
Many modern communication systems demand multifunctional RF front-end. Multifunctional
antenna such as reconfigurable and filtering antennas have the advantage because it can reduce the overall
size and complexity in the systems [1]. However, this antenna also exposed to unwanted harmonic
frequencies which can cause interference in the communication system. Therefore, filter can be used to
remove unwanted frequency by means of being completely eliminated or partially suppressed them.
There are many types of filter can be used as the filtering purposes in the RF front-end. Various
filter structures are presented [2]-[13] such as parallel coupled line technique, stepped impedance resonator
and multimode resonator.
Filter presented in [2], [3] have dual-band band-pass filter. Filter in [2] consists of symmetrical
Y-shaped central-loaded stepped-impedance, overlapped with the hexagon ring resonator. It has a center
frequency at 1.9 GHz and 3.4 GHz, with the minimum insertion loss results of 0.9 dB and 1.0 dB,
respectively. The simple structure is based on parallel coupled line technique of filter in [3], it has an
insertion loss at 2.4 GHz for -0.6 dB while at 5 GHz for -2.1 dB. Filters with more than a quad-band are also
been reported in [4]-[5]. By using multimode resonator (MMR), λ/4 resonator with mixed electric and
magnetic coupling (MEMC), filter in [4] has a quint-band bandpass. Center frequencies are achieved at
2.1 GHz, 3.0 GHz, 4.0 GHz, 4.7 GHz and 7.2 GHz with the insertion loss of 0.98 dB, 1.78 dB, 1.22 dB,

Int J Elec & Comp Eng ISSN: 2088-8708 
Band-pass Filter with Harmonics Suppression Capability (Izni Husna Idris)
2513
1.77 dB and 2.39 dB, respectively. However, the more bands the filter has, the more complex structure or
design of filters will become.
Ultra-wideband bandpass filter is reported in [6], achieved from 3.1 GHz to 10.6 GHz with
minimum insertion loss of 1 dB. The filter consists of λ/2 stepped impedance resonator (SIR) with a short
stub and two open-circuited stubs loaded. Another filter covers from 1.72 GHz to 3.99 GHz is presented in
[7] with the insertion loss of 0.81 dB. The filter is composed of square-loop resonator, three-coupled line load
and interdigital feed lines. UWB bandpass filter ranging from 0.5 GHz to 1.9 GHz is achieved in [8]. The
filter also has seven transmission zeros which are located from 2.04 GHz to 5.9 GHz with insertion loss
greater than 20 dB. A compact bandpass filter with source-load coupling cover from 3.08 GHz to 4.34 GHz
[13]. It consists of triple-mode stub-loaded resonator which can generate one odd mode and two even modes.
However, this filter has a complex design in order to achieve a wide range of passband and stopband
simutanoeusly.
This paper presents a Band-pass Filter (BPF) with a very wide suppressions band. The analysis of
the filter which consists of two pairs of modified U-shaped slot is presented. With this structure, the proposed
structure is able to have a band-pass from 1.3 GHz to 3.3 GHz and supressed the other unwanted frequencies
up to 4th harmonics. To verify the performance, the filter is fabricated and measured. Both of the simulated
and measured results are agreed reasonably well, demonstrating that the filter has a good band-pass
bandwidth and broadband harmonic suppression.
2. PARAMETRIC STUDIES FOR FILTER DESIGN
Harmonic frequencies can somehow contribute to an error and a problem to the wireless
communication systems. By integrating a filter to an antenna structure, the harmonic frequencies can be
eliminated. There are many designs or shapes of filter introduced from the previous research works. For
example; ring-shape, bowtie-shape, square/rectangle-shape and U/L/Г/π-shape are introduced to filtering an
antenna frequency. In this paper, a modified U-shaped slot filter with a CPW-fed has been designed.
2.1. Single-, dual-, triple- and quad-line (s) rectangle-shape of filter
The forming of modified U-shaped slot is based from rectangle slot. Figure 1 shows a single
rectangle-shape slot and was given a name as configuration A. The substrate dimension is 150 x 100 mm2
(length, l x width, w). The single slot denoted as a stub1 has a dimension of length=l1 and width=w1, placed
in the middle of CPW feedline with f=3 mm and g=0.5 mm. The slot length, l1 is approximately a quarter
wavelength at the operating frequency. Thus creating a stop-band function.
l
ww1
l1
f
g
stub1 stub1
Configuration A
Figure 1. Configuration A – single-line, rectangle slot
Figure 2(a) shows insertion loss (S21) results of Configuration A by varying l1 when w1 of stub 1 is
fixed at 1 mm. When l1=9 mm, the -10 dB stopband bandwidth is 4.76 GHz to 6.12 GHz, with the center
frequency, fc=5.4 GHz. When l1=10 mm, the bandwidth is covered from 4.21 GHz to 5.65 GHz, with fc=4.8
GHz. Bandwidth is ranging from 3.87 GHz to 5 GHz when l1=11 mm, with fc=4.3 GHz.
Meanwhile, Figure 2(b) shows S21 results when l1 is fixed at 10 mm and the value of w1 is varied
from 1 mm to 5 mm. Bandwidth percentage is increasing from 14.6% (w1=1 mm) to 20.8% (w1=3 mm) and
24.1% (w1=5 mm). From both of the figures, we can notice that if the length of the stub is shorter, the center
frequency (fc) is higher as shown in Equation (1). Meanwhile, when the width of the slot is wider, the quality
factor becomes lower and thus the bandwidth is increased.
l ∝ 1 / f (1)

 ISSN: 2088-8708
Int J Elec & Comp Eng, Vol. 8, No. 4, August 2018 : 2512 – 2520
2514
Frequency, GHz
1 2 3 4 5 6 7 8 9
S21,dB
-40
-30
-20
-10
0
l1=9 mm
l1=10 mm
l1=11 mm
Frequency, GHz
1 2 3 4 5 6 7 8 9
S21,dB
-40
-30
-20
-10
0
w1=1 mm
w1=3 mm
w1=5 mm
(a) (b)
Figure 2. S21 Results of configuration A when (a) Vary l1, w1=1 (b) Vary w1, l1=10
Other rectangle slot shape such as dual-lines, triple-lines and quad-lines are shown in Figure 3,
Figure 4 and Figure 5. Dual-lines, rectangle slot as shown in Figure 3(a) consists of two slots known as stub1
and stub2. The structure is given a name as Configuration B. Stub1 has a dimension of l1 x w1 while stub2
has a dimension of l2 x w2. The distance between stub1 and stub2 is 1 mm. Figure 3(b) shows the insertion
loss results of Configuration B when l1=9 mm and l2=7 mm. Value of w1 and w2 is fixed at 1 mm. The low-
pass response is achieved from 2 GHz to 5 GHz. By adding an additional slot, the stop band frequency range
is wider compared to having only one slot. For example, the band-stop is achieved from 4.8 GHz to 6.1 GHz
using Configuration A (l1=9 mm). Meanwhile, by using Configuration B (l1=9 mm, l2=7 mm), the band-stop
covers from 4.9 GHz to 8.0 GHz. The introduction of stub2 has helped to create a stopband at higher
frequency.
(a) (b) (c)
Figure 3. (a) Configuration B - dual-lines, rectangle slot (b) S21 result when l1=9, l2=7 (b) S21 result;
configuration B vs configuration A
Figure 4(a) has three stubs where the size of stub1 is l1 x w1, stub2 is l2 x w2 and stub3 is l3 x w3.
The structure is denoted as Configuration C. The distance between each stub is 1 mm. Figure 4(b) shows the
insertion loss result of Configuration C when l1=12 mm, l2=9 mm, l3=7 mm. Value of w1, w2 and w3 is
fixed at 1 mm. With this configuration, the band-stop is now wider which covers from 3.7 GHz to 7.8 GHz.
Quad-lines, the rectangle shape shown in Figure 5(a) has one additional stub compared to the triple
stub known as stub4. This structure is known as Configuration D. The size of stub 4 is l4 x w4. The rest of
the stubs are the same as previous Configuration C. The Band-stop from 3.7 GHz to 9.0 GHz is now achieved
when l1=12 mm, l2=9 mm, l3=7 mm, l4=6 mm as shown in Figure 5(b). Value of w1, w2, w3 and w4 is fixed
at 1 mm. The distance between each stub is 1 mm. Therefore, it can be concluded that when an additional
rectangular shape slot is added to the filter structure, multiple stopbands are achieved and the combination of
these stopbands make the bandwidth of the band-stop become wider.

2515
(a) (b)
Figure 4. (a) Configuration C - triple-lines, rectangle slot (b) S21 result;
configuration C vs configuration B
(a) (b)
Figure 5. (a) Configuration D - quad-lines, rectangle slot (b) S21 result;
configuration D vs configuration C
2.2. Combined dual-, triple- and quad-lines rectangle-shape of filter
Figure 6(a), Figure 6(b) and Figure 6(c) show the combination of dual-, triple- and quad-lines into
one unit of the resonator namely Configurations E, F and G respectively. There are two connecting boxes
known as boxt and boxr. The dimension of the boxt is lt x wt while the boxr is lr x wr as shown in
Figure 6(d) and Figure 6(e) respectively. In this paper, the size of the boxt is fixed at 1 mm x 1 mm while the
size of the boxr is fixed at 2 mm x 1 mm, unless it is mentioned otherwise.
Figure 7(a) show the S21 result of Configuration E when the length of l1=9 mm and l2=7 mm while
w1=w2=1 mm. The result is compared to Configuration B with the same length of l1, l2, w1 and w2. By
having connecting part, the filter result of Configuration E is different, even though the length is same as
Configuration B. Therefore, to analyze the result obtained in Figure 7(a), both of the rectangular slot length
in Configuration B are added by 1 mm. As a result, Configuration E with l1=9 mm and l2=7 mm produced
quite same bandwidth size with the filter of Configuration B; l1=10 mm and l2=8 mm. When boxt and boxr
is added to the antenna structure, the insertion loss of the filter will produce a slight notch (blue circle) as
shown in Figure 7. The notch occurs depending on the distance between each stub (e.g. wr and wy). The
wider the width between the stubs (e.g. distance between stub1 and stub2 or between stub2 and stub3), the
smaller the bandwidth of the notch will be produced as shown in Figure 7(c).
The insertion loss result of Configurations F and G are shown in Figure 8. Both of the results are
being compared with the same length of stubs but different in configurations. Configuration F is compared
with C while Configuration G is compared with D. As expected from Figure 7, results in Figure 8 also have a
slight notch coming from the distance between each slot (e.g. wr and wy). This will prevent the filter to have
wide bandwidth for the band-stop. Therefore, Configuration D is the best results so far in term of bandwidth
performance. However, the filter requires four pairs of switch to turn on and off the filter later on.

 ISSN: 2088-8708
2516
l1
l2
stub1
stub2
stub1
stub2 w2
w1
Configuration E
stub1
stub2
stub3
stub1
stub2
stub3
Configuration F
stub4
stub3
stub2
stub1
stub4
stub3
stub2
stub1
Configuration G
(a) (b) (c)
BoxtBoxr Boxt Boxr
stub1
stub2
stub1
stub2
stub1
stub2
lt
lr
wt wr
(d) (e)
Figure 6. Combined rectangle slots’ shapes (a) Dual-lines (b) Triple-lines (c) Quad-lines (d) Zoom-in boxt
and boxr (e) Dimension of boxt and boxr
(a) (b) (c)
Figure 7. S21 results of (a) Configuration E vs configuration B – same length (b) Configuration E vs
configuration B – different length (c) Configuration E (l1=9 mm and l2=7 mm), vary wr
(a) (b)
Figure 8. S21 results of (a) Configuration F vs configuration C (b) Configuration G vs configuration D
2.3. Other configuration of filter
In this paper, another possibility of configuration is investigated to achieve a better result in term of
the insertion loss, S21. For example, a combination of one Configuration E and one Configuration A will
produce the Configuration J as shown in Figure 9(a). Other configuration as shown in Figure 9(b) is a

2517
combination of one Configuration E and two Configurations A will produce Configuration K. Lastly,
Figure 9(c) is a combination of two units of Configuration E to become a Configuration L. Because of
Configuration L have two units of connecting part, the upper unit of connecting part is known as boxt and
boxr while the lower unit is known as boxv and boxy.
stub1
stub2
stub3
stub1
stub2
stub3
Configuration J
stub4
stub3
stub2
stub1
stub4
stub3
stub2
stub1
Configuration K
stub4
stub3
stub2
stub1
stub4
stub3
stub2
stub1
Configuration L
(a) (b) (c)
Figure 9. Rectangle slot shape (a) Combine dual and single-line (b) Combine dual and two single-line
(c) Two units of combine dual-lines
Based on Figure 10, we noticed that the Configuration L provide better performance in terms of
bandwidth compared to Configuration K. Configuration J, with the size of l1=12 mm, l2=9 mm and l3=7 mm
have the stopband results from 3.39 GHz to 4.10 GHz and 5.12 GHz to 7.67 GHz as shown in Figure 10(a).
The maximum ratio for Configuration J is 1.5:1.
Configuration K, with the size of l1=12 mm, l2=9 mm, l3=7 mm and l4=6 mm has a stopband
ranging from 3.44 GHz to 9 GHz with the ratio of 2.62:1 as shown in Figure 10(b). Figure 10(c) shows the
stopband result from 3.41 GHz to 9 GHz for Configuration L with the ratio of 2.64:1. Configuration L has the
same length as Configuration K but different in shape. Therefore, Configuration L is chosen because it can
provide wider bandwidth and less switch is used compared to Configuration D. The bandwidth of band-stop
can be improved by selecting the right length of the rectangular slot shape and the width of the distance
between each slot.
(a) (b) (c)
Figure 10. S21 results of (a) Configuration J vs configuration E and configuration A (b) Configuration K vs
configuration E and configuration B (c) Configuration L vs configuration E
3. FINAL DESIGN OF PROPOSED FILTER
Figure 11(a) shows the final design of the proposed filters. Zoom-in views of the upper and lower
connecting part are shown in Figure 11(b) and Figure 11(c). The dimensions of the filter are listed in Table 1.
In this design, the filter should have a band-pass result from 1.5 GHz to 3.0 GHz. This is because, the higher
order modes will be eliminated when the filter is applied to an antenna structure. Figure 11(d) shows the
photograph of the fabricated filter using FR4 substrate with a thickness of 1.6 mm.

 ISSN: 2088-8708
2518
(a) (b)
(c) (d)
Figure 11. (a) Final design of the proposed filter (b) Zoom-in view of the upper connecting part (c) Zoom-
in view of the lower connecting part (d) Photo of the fabricated filter
Table 1. Dimensions of the Final Design
Parameter Size (mm) Parameter Size (mm) Parameter Size (mm) Parameter Size (mm)
l 150 w 100 f 3 g 0.5
l1 40 l2 9 l3 7 l4 6
w1 1 w2 3 w3 1 w4 1
lt 1 lr 2 lv 1 ly 2
wt 1 wr 3 wv 1 wy 1
Figure 12 shows the simulated and measured results of the final design of the proposed filter as
shown in Figure 11(d). The results show good agreements between simulation and measurement. The
insertion loss in Figure 12 shows that the band-pass is measured from 1.35 GHz to 3.31 GHz against that of
the simulated result ranging from 1.38 GHz to 3.29 GHz. Two transmission zeroes are created near the
passband. The 10 dB rejection band therefore is extended to 9 GHz, for both simulated and measured results.
Frequency, GHz
1 2 3 4 5 6 7 8 9
S21,dB
-40
-30
-20
-10
0
S11 (simulated)
S21 (simulated)
S11 (measured)
S21 (measured)
1.35 - 3.31 GHz
Figure 12. Simulated and measured S11 and S21 results of the proposed filter

2519
4. CONCLUSION
A new design of band-pass filter with harmonic suppression is presented. The proposed filter is
achieved based on connecting two shape of the rectangular-slot into one unit of filter known as a U-shaped
slot. By having two pairs of U-shaped slots, the filter has a wider rejection band from 3.33 GHz to 9 GHz.
The proposed filter shows that it can eliminate the harmonic frequencies effectively.
ACKNOWLEDGEMENTS
The authors would like to acknowledge the Ministry of Higher Education (MoHE) Malaysia, UTM
under the GUP Grant (Q.J130000.2623.14J18) and Advanced RF and Microwave Research Group
(ARFMRG) for supporting this work.
REFERENCES
[1] A. N. Obadiah, et al., “A review on filter-antennas” Applied Mechanics and Materials, vol. 735, pp. 289-293,
Feb 2015.
[2] M.-C. Tang and T. Shi, “A novel central-stub-loaded, dual-band bandpass filter for PCS and WiMAX application”
IEEE International Microwave Workshop Series on Advanced Materials and Processes for RF and THz
Applications (IMWS-AMP), pp.1-3, 2015.
[3] R. A. Rahim, et. al., “Microstrip dual-band bandpass filter for ISM band applications” IEEE International
Conference on Control System, Computing and Engineering, pp. 281-286, 2015.
[4] J. Ai, et. al., “Miniaturized Quint-band bandpass filter based on multi-mode resonator and λ/4 resonator with mixed
electric and magnetic coupling” IEEE Microwave and Wireless Components Letters, vol. 26, 343-345, 2016.
[5] K.-W. Hsu, et. al., “Compact parallel-coupled sext-band bandpass filter using semi-lumped resonators” IEEE
International Microwave Symposium (IMS), pp. 1-4, 2016.
[6] D. Li, et. al., “A novel UWB bandpass filter based on quadruple-mode resonator” IEEE International Wireless
Symposium (IWS), pp. 1-3, 2015.
[7] S. Punyawarin and N. Siripon, “A novel wideband bandpass filter using square loop resonator and three-coupled
line load, 12th
International Conference on Electrical Engineering/Electronics, Computer, Telecommunications and
Information Technology (ECTI-CON), pp. 1-4, 2015.
[8] X. Gao, et. al., “Compact ultra-wideband bandpass filter with improved upper stopband using open/shorted stubs”
IEEE Microwave and Wireless Components Letters, vol. 27, pp. 123-125, 2017.
[9] S. A. Hamzah, et. al., “Reduced size harmonic suppressed fractal dipole antenna with reconfigurable feature”
Proceedings of Asia-Pacific Microwave Conference, pp. 2040-2043, 2010.
[10] F. Darwis, et. al., “Design of compact microstrip U shape bandpass filter using via ground holes” TELKOMNIKA
(Telecommunication, Computing, Electronics and Control), vol. 14, pp. 82-85, 2016.
[11] A. Boutejdar, et. al., “Design and improvement of a compact bandpass filter using DGS technique for WLAN and
WiMAX Applications” TELKOMNIKA (Telecommunication, Computing, Electronics and Control), vol. 15, pp.
1137-1144, 2017.
[12] D. A. A. Mat, et. al., “Integrated open loop resonator filter designed with notch patch antenna for microwave
applications” TELKOMNIKA (Telecommunication, Computing, Electronics and Control), vol. 15,
pp. 1485-1492, 2017.
[13] W. Chen, et. al., “Compact and wide upper-stopband triple-mode broadband microstrip BPF” TELKOMNIKA
(Telecommunication, Computing, Electronics and Control), vol. 10, pp. 353-358, 2012.
BIOGRAPHIES OF AUTHORS
Izni Husna Idris received B. Eng. and M. Eng. degrees in electrical engineering from Universiti
Teknologi Malaysia (UTM). Now, she is pursuing the PhD degree in Advanced RF and Microwave
Research Group (ARFMRG), UTM Johor, Malaysia. Her research interests include reconfigurable
antenna design and multi-function antenna for wireless communication systems application.
Mohamad Rijal Hamid received the M.Sc. degrees in communication engineering from the
Universiti Teknologi Malaysia, Johor Bahru, Malaysia, in 2001 and the PhD degree at the University
of Birmingham, Birmingham, U.K. in 2011. He has been with Universiti Teknologi Malaysia (UTM)
at the Faculty of Electrical Engineering (FKE), UTM, since 1999. Currently his position is a Senior
Lecturer. His major research interest is reconfigurable antenna design for multimode wireless
applications.

 ISSN: 2088-8708
2520
Kamilia Kamardin received her B. Eng. Electronic (Communications) from the University of
Sheffield, U.K., in 2004 and obtained her M.Sc. in Information Technology (Data Communications
and Networking) from Universiti Teknologi Mara (UiTM), Malaysia in 2007. She received her Ph.D.
in Electrical Engineering (Communications) from Universiti Teknologi Malaysia (UTM), Malaysia in
2014. She spent 3 months at University of Bimingham, U.K., as a visiting Ph.D. student. She serves
under Computer Systems Engineering Group at Advanced Informatics School. Her research interests
include antennas, wireless communication, wearable communication, body centric communication,
metamaterials, wireless networking, Internet of Things (IoT) and computer systems engineering.
Mohamad Kamal A Rahim received the B Eng. degree in Electrical and Electronic Engineering from
University of Strathclyde, UK, in 1987. In 1989, he joined the Department of Communication
Engineering, Faculty of Electrical Engineering Universiti Teknologi Malaysia Kuala Lumpur as an
Assistant Lecturer A. He obtained his M.Eng Science from University of New South Wales Australia
in 1992 and PhD degrees in Electrical Engineering from University of Birmingham UK in 2003. Now
he is the Professor in RF and Antenna at Faculty of Electrical Engineering Universiti Teknologi
Malaysia. His research interest includes the areas of design of Dielectric resonator antennas, microstrip
antennas, small antennas, microwave sensors, RFID antennas for readers and tags, multi-function
antennas, microwave cicuits, EBG, artificial magnetic conductors, metamaterials, phased array
antennas, computer aided design for antennas and design of millimeter frequency antennas. He has
published over 200 articles in journals and conference papers.
Farid Zubir received the B. Eng. degree in Electrical Engineering majoring in Telecommunication as
well as M. Eng. degree (Communication) from the Universiti Teknologi Malaysia in 2008 and 2010
respectively. In 2016, he then obtained his Ph.D degree from the University of Birmingham, UK, for
research into direct integration of power amplifiers with antennas in microwave transmitters. He is
currently serves as a Senior Lecturer at the Department of Communication Engineering, Faculty of
Electrical Engineering, Universiti Teknologi Malaysia. His current research interest and specialization
are in the area of RF and Microwave technologies including Planar Array Antennas, Dielectric
Resonator Antennas (DRAs), Active Integrated Antenna (AIA), Microstrip Reflectarray Antenna
(MRA), Millimeter wave Antennas, Electromagnetic Band Gap (EBG), Artificial Magnetic Conductor
(AMC), Full-integrated Transmitting Amplifiers, Linear PAs, Doherty PAs and Bias Decoupling
Circuits. He has published over 30 articles in journals, book chapters, conference papers and
proceedings.
Huda A Majid received his B.Eng Electrical (Telecommunication) in 2007, M.Eng Electrical in 2010
and obtained his PhD Electrical Engineering in 2013 from Universiti Teknologi Malaysia (UTM). He
is currently serves as a lecturer at Faculty of Engineering Technology in Universiti Tun Hussein Onn
Malaysia (UTHM). His research interest include reconfigurable antenna and metamaterial structures.

Band-pass Filter with Harmonics Suppression Capability

More Related Content

What's hot (19)

Similar to Band-pass Filter with Harmonics Suppression Capability (20)

More from IJECEIAES (20)

Recently uploaded (20)

Band-pass Filter with Harmonics Suppression Capability